Abstract: The hydraulic actuated excavator, being a non-linear
mobile machine, encounters many uncertainties. There are
uncertainties in the hydraulic system in addition to the uncertain
nature of the load. The simulation results obtained in this study show
that there is a need for intelligent control of such machines and in
particular interval type-2 fuzzy controller is most suitable for
minimizing the position error of a typical excavator-s bucket under
load variations. We consider the model parameter uncertainties such
as hydraulic fluid leakage and friction. These are uncertainties which
also depend up on the temperature and alter bulk modulus and
viscosity of the hydraulic fluid. Such uncertainties together with the
load variations cause chattering of the bucket position. The interval
type-2 fuzzy controller effectively eliminates the chattering and
manages to control the end-effecter (bucket) position with positional
error in the order of few millimeters.
Abstract: In this paper a three dimensional thermal model of
high breaking capacity fuse with unequal fuse links is proposed for
both steady-state or transient conditions. The influence of ambient
temperature and electric current on the temperature distribution
inside the fuse, has been investigated. A thermal analysis of the
unbalanced distribution of the electric current through the fuse
elements and their influence on fuse link temperature rise, has been
performed. To validate the three dimensional thermal model, some
experimental tests have been done. There is a good correlation
between experimental and simulation results.
Abstract: A composite made of plasma functionalized multiwall
carbon nanotubes (MWNTs) coated with SnO2 was synthesized by
sonochemical precipitation method. Thick layer of this
nanocomposite material was used as ethanol sensor at low
temperatures. The composite sensitivity for ethanol has increased by
a factor of 2 at room temperature and by a factor of 13 at 250°C in
comparison to that of pure SnO2. SEM image of nanocomposite
material showed MWNTs were embedded in SnO2 matrix and also a
higher surface area was observed in the presence of functionalized
MWNTs. Greatly improved sensitivity of the composite material to
ethanol can be attributed to new gas accessing passes through
MWNTs and higher specific surface area.
Abstract: The presented article deals with the description of a
numerical model of a corridor at a Central Interim Spent Fuel Storage
Facility (hereinafter CISFSF). The model takes into account the
effect of air flows on the temperature of stored waste. The
computational model was implemented in the ANSYS/CFX
programming environment in the form of a CFD task solution, which
was compared with an approximate analytical calculation. The article
includes a categorization of the individual alternatives for the
ventilation of such underground systems. The aim was to evaluate a
ventilation system for a CISFSF with regard to its stability and
capacity to provide sufficient ventilation for the removal of heat
produced by stored casks with spent nuclear fuel.
Abstract: The study of interaction among the grain, moisture,
and the surrounding space (air) is key to understanding the graindrying
process. In Iran, rice (mostly Indica type) is dried by flat
bed type dryer until the final MC reaches to 6 to 8%. The
experiments were conducted to examine the effect of application of
discharge fan with different heights of paddy on the drying
efficiency. Experiments were designed based on two different
configurations of the drying methods; with and without discharge
fan with three different heights of paddy including; 5, 10, and 15
cm. The humid heated air will be going out immediately by the
suction of discharge fan. The drying time is established upon the
average final MC to achieve about 8%. To save energy and reduce
the drying time, the distribution of temperature between layers
should be fast and uniform with minimum difference; otherwise
the difference of MC gradient between layers will be high and will
induce grain breakage. The difference of final MC between layers
in the two methods was 48-73%. The steady state of temperature
between the two methods has saved time in the range of 10-20%,
and the efficiency of temperature distribution increased 17-26% by
the use of discharge fan.
Abstract: In the past many uneconomic solutions for limitation
and interruption of short-circuit currents in low power applications
have been introduced, especially polymer switch based on the
positive temperature coefficient of resistance (PCTR) concept.
However there are many limitations in the active material, which
consists of conductive fillers. This paper presents a significantly
improved and simplified approach that replaces the existing current
limiters with faster switching elements. Its elegance lies in the
remarkable simplicity and low-cost processes of producing the device
using polyaniline (PANI) doped with methane-sulfonic acid (MSA).
Samples characterized as lying in the metallic and critical regimes of
metal insulator transition have been studied by means of electrical
performance in the voltage range from 1V to 5 V under different
environmental conditions. Moisture presence is shown to increase the
resistivity and also improved its current limiting performance.
Additionally, the device has also been studied for electrical resistivity
in the temperature range 77 K-300 K. The temperature dependence of
the electrical conductivity gives evidence for a transport mechanism
based on variable range hopping in three dimensions.
Abstract: Herein, the organic semiconductor methyl orange
(MO), is investigated for the first time for its electronic applications.
For this purpose, Al/MO/n-Si heterojunction is fabricated through
economical cheap and simple “drop casting” technique. The currentvoltage
(I-V) measurements of the device are made at room
temperature under dark conditions. The I-V characteristics of
Al/MO/n-Si junction exhibits asymmetrical and rectifying behavior
that confirms the formation of diode. The diode parameters such as
rectification ratio (RR), turn on voltage (Vturn on), reverse saturation
current (I0), ideality factor (n), barrier height ( b
f ), series resistance
(Rs) and shunt resistance (Rsh) are determined from I-V curves using
Schottky equations. These values of these parameters are also
extracted and verified by applying Cheung’s functions. The
conduction mechanisms are explained from the forward bias I-V
characteristics using the power law.
Abstract: The present work represents an investigation of the
hydrolysis of hull-less pumpkin (Cucurbita Pepo L.) oil cake protein
isolate (PuOC PI) by pepsin. To examine the effectiveness and
suitability of pepsin towards PuOC PI the kinetic parameters for
pepsin on PuOC PI were determined and then, the hydrolysis process
was studied using Response Surface Methodology (RSM). The
hydrolysis was carried out at temperature of 30°C and pH 3.00. Time
and initial enzyme/substrate ratio (E/S) at three levels were selected
as the independent parameters. The degree of hydrolysis, DH, was
mesuared after 20, 30 and 40 minutes, at initial E/S of 0.7, 1 and 1.3
mA/mg proteins. Since the proposed second-order polynomial model
showed good fit with the experimental data (R2 = 0.9822), the
obtained mathematical model could be used for monitoring the
hydrolysis of PuOC PI by pepsin, under studied experimental
conditions, varying the time and initial E/S. To achieve the highest
value of DH (39.13 %), the obtained optimum conditions for time
and initial E/S were 30 min and 1.024 mA/mg proteins.
Abstract: Green propellants used for satellite-level propulsion
system become attractive in recent years because the non-toxicity and
lower requirements of safety protection. One of the green propellants,
high-concentration hydrogen peroxide H2O2 solution (≥70% w/w,
weight concentration percentage), often known as high-test peroxide
(HTP), is considered because it is ITAR-free, easy to manufacture and
the operating temperature is lower than traditional monopropellant
propulsion. To establish satellite propulsion technology, the National
Space Organization (NSPO) in Taiwan has initialized a long-term
cooperation project with the National Cheng Kung University to
develop compatible tank and thruster. An experimental propulsion
payload has been allocated for the future self-reliant satellite to
perform orbit transfer and maintenance operations. In the present
research, an 1-Newton thruster prototype is designed and the thrusting
force is measured by a pendulum-type platform. The preliminary
hot-firing test at ambient environment showed the generated thrust and
the specific impulse are about 0.7 Newton and 102 seconds,
respectively.
Abstract: Copper sulfide nanoparticles (CuS) were successfully synthesized by the pulsed plasma in liquid method, using two copper rod electrodes submerged in molten sulfur. Low electrical energy and no high temperature were applied for synthesis. Obtained CuS nanoparticles were then analyzed by means of X-ray diffraction, Low and High Resolution Transmission Electron Microscopy, Electron Diffraction, X-ray Photoelectron, Raman Spectroscopies and Field Emission Scanning Electron Microscopy. XRD analysis revealed peaks for CuS with hexagonal phase composition. TEM and HRTEM studies showed that sizes of CuS nanoparticles ranged between 10-60 nm, with the average size of about 20 nm. Copper sulfide nanoparticles have short nanorod-like structure. Raman spectroscopy found peak for CuS at 474.2cm-1of Raman region.
Abstract: An organic bulk heterojunction (BHJ) was fabricated using a blended film containing Copper (II) tetrakis(4-acumylphenoxy) phthalocyanine (Tc-CuPc) along with [6,6]-Phenyl C61 butyric acid methyl ester (PCBM). Weight ratio between Tc-CuPc and PCBM was 1:1. The electrical properties of Tc-CuPc: PCBM BHJ were examined. Rectifying nature of the BHJ was displayed by current-voltage (I-V) curves, recorded in dark and at various temperatures. At low voltages, conduction was ohmic succeeded by space-charge limiting current (SCLC) conduction at higher voltages in which exponential trap distribution was dominant. Series resistance, shunt resistance, ideality factor, effective barrier height and mobility at room temperature were found to be 526 4, 482 k4, 3.7, 0.17 eV and 2×10-7 cm2V-1s-1 respectively. Temperature effect towards different BHJ parameters was observed under dark condition.
Abstract: Organic Flash Cycle (OFC) has potential of improving
efficiency for recovery of low temperature heat sources mainly due to
reducing temperature mismatch in the heat exchanger. In this work
exergetical performance analysis of ORC is conducted for recovery of
low grade heat source. Effects of system parameters such as flash
evaporation temperature or heating temperature are theoretically
investigated on the exergy destructions (anergies) at various
components of the system as well as exergy efficiency. Results show
that exergy efficiency has a peak with respect to the flash temperature,
and the optimum flash temperature increases with the heating
temperature. The component where the largest exergy destruction
occurs varies with the flash temperature or heating temperature.
Abstract: This paper presents one of the best applications of wireless sensor network for campus Monitoring. With the help of PIR sensor, temperature sensor and humidity sensor, effective utilization of energy resources has been implemented in one of rooms of Sharda University, Greater Noida, India. The RISC microcontroller is used here for analysis of output of sensors and providing proper control using ZigBee protocol. This wireless sensor module presents a tremendous power saving method for any campus
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: In the present study, the surface temperature history of the adaptor part in a two-stage supersonic launch vehicle is accurately predicted. The full Navier-Stokes equations are used to estimate the aerodynamic heat flux and the one-dimensional heat conduction in solid phase is used to compute the temperature history. The instantaneous surface temperature is used to improve the applied heat flux, to improve the accuracy of the results.
Abstract: The new idea of this research is application of a new fault detection and isolation (FDI) technique for supervision of sensor networks in transportation system. In measurement systems, it is necessary to detect all types of faults and failures, based on predefined algorithm. Last improvements in artificial neural network studies (ANN) led to using them for some FDI purposes. In this paper, application of new probabilistic neural network features for data approximation and data classification are considered for plausibility check in temperature measurement. For this purpose, two-phase FDI mechanism was considered for residual generation and evaluation.
Abstract: This paper characterizes the effects of artificial short
term aging in the laboratory on the rheological properties of virgin
80/100 penetration grade asphalt binder. After several years in
service, asphalt mixture started to deteriorate due to aging. Aging is a
complex physico-chemical phenomenon that influences asphalt
binder rheological properties causing a deterioration in asphalt
mixture performance. To ascertain asphalt binder aging effects, the
virgin, artificially aged and extracted asphalt binder were tested via
the Rolling Thin film Oven (RTFO), Dynamic Shear Rheometer
(DSR) and Rotational Viscometer (RV). A comparative study
between laboratory and field aging conditions were also carried out.
The results showed that the specimens conditioned for 85 minutes
inside the RTFO was insufficient to simulate the actual short term
aging caused that took place in the field under Malaysian field
conditions
Abstract: This paper presents the study of induced currents and
temperature distribution in gear heated by induction process using 2D
finite element (FE) model. The model is developed by coupling
Maxwell and heat transfer equations into a multi-physics model. The
obtained results allow comparing the medium frequency (MF) and
high frequency (HF) cases and the effect of machine parameters on
the evolution of induced currents and temperature during heating.
The sensitivity study of the temperature profile is conducted and the
case hardness is predicted using the final temperature profile. These
results are validated using tests and give a good understanding of
phenomena during heating process.
Abstract: Future astronomical projects on large space x-ray
imaging telescopes require novel substrates and technologies for the
construction of their reflecting mirrors. The mirrors must be
lightweight and precisely shaped to achieve large collecting area with
high angular resolution. The new materials and technologies must be
cost-effective. Currently, the most promising materials are glass or
silicon foils. We focused on precise shaping these foils by thermal
forming process. We studied free and forced slumping in the
temperature region of hot plastic deformation and compared the
shapes obtained by the different slumping processes. We measured
the shapes and the surface quality of the foils. In the experiments, we
varied both heat-treatment temperature and time following our
experiment design. The obtained data and relations we can use for
modeling and optimizing the thermal forming procedure.
Abstract: Thirty three re-wetting tests were conducted at
different combinations of temperatures (5.7- 46.30C) and relative
humidites (48.2-88.6%) with barley. Two most commonly used thinlayer
drying and rewetting models i.e. Page and Diffusion were
compared for their ability to the fit the experimental re-wetting data
based on the standard error of estimate (SEE) of the measured and
simulated moisture contents. The comparison shows both the Page
and Diffusion models fit the re-wetting experimental data of barley
well. The average SEE values for the Page and Diffusion models
were 0.176 % d.b. and 0.199 % d.b., respectively. The Page and
Diffusion models were found to be most suitable equations, to
describe the thin-layer re-wetting characteristics of barley over a
typically five day re-wetting. These two models can be used for the
simulation of deep-bed re-wetting of barley occurring during
ventilated storage and deep bed drying.