Abstract: This article is focused on the calculation of heat
radiation intensity and its optimization on an aluminum mould
surface. The inside of the mould is sprinkled with a special powder
and its outside is heated by infra heaters located above the mould
surface, up to a temperature of 250°C. By this way artificial leathers
in the car industry are produced (e. g. the artificial leather on a car
dashboard). A mathematical model of heat radiation of infra heaters
on a mould surface is described in this paper. This model allows us to
calculate a heat-intensity radiation on the mould surface for the
concrete location of infra heaters above the mould surface. It is
necessary to ensure approximately the same heat intensity radiation
on the mould surface by finding a suitable location for the infra
heaters, and in this way the same material structure and color of
artificial leather. In the model we have used a genetic algorithm to
optimize the radiation intensity on the mould surface. Experimental
measured values for the heat radiation intensity by a sensor in the
surroundings of an infra heater are used for the calculation
procedures. A computational procedure was programmed in language
Matlab.
Abstract: The power transformer is the most expensive, indispensable and arguably the most important equipment item in a power system Insulation failure in transformers can cause long term interruption to supply and loss of revenue and the condition assessment of the insulation is thus an important maintenance procedure. Oil-impregnated transformer insulation consists of mainly organic materials including mineral oil and cellulose-base paper and pressboard. The operating life of cellulose-based insulation, as with most organic insulation, depends heavily on its operating temperature rise above ambient. This paper reports results of a laboratory-based experimental investigation of partial discharge (PD) activity at high temperature in oil-impregnated insulation. The experiments reported here are part an on-going programme aimed at investigating the way in which insulation deterioration can be monitored and quantified by use of partial discharge diagnostics. Partial discharge patterns were recorded and analysed during increasing and decreasing phases of the temperature. The effect of ageing of the insulation on the PD patterns in oil and oil-impregnated insulation are also considered.
Abstract: A zero dimensional model has been used to investigate
the combustion performance of a single cylinder direct injection
diesel engine fueled by biofuels with options like supercharging and
exhaust gas recirculation. The numerical simulation was performed at
constant speed. The indicated pressure, temperature diagrams are
plotted and compared for different fuels. The emissions of soot and
nitrous oxide are computed with phenomenological models. The
experimental work was also carried out with biodiesel (palm stearin
methyl ester) diesel blends, ethanol diesel blends to validate
simulation results with experimental results, and observed that the
present model is successful in predicting the engine performance with
biofuels.
Abstract: Composites based on a biodegradable polycaprolactone (PCL) containing 0.5, 1.0 and 2.0 wt % of titanium dioxide (TiO2) micro and nanoparticles were prepared by melt mixing and the effect of filler type and contents on the thermal properties, dynamic-mechanical behaviour and morphology were investigated. Measurements of storage modulus and loss modulus by dynamic mechanical analysis (DMA) showed better results for microfilled PCL/TiO2 composites than nanofilled composites, with the same filler content. DSC analysis showed that the Tg and Tc of micro and nanocomposites were slightly lower than those of neat PCL. The crystallinity of the PCL increased with the addition of TiO2 micro and nanoparticles; however, the cc for the PCL was unchanged with micro TiO2 content. The thermal stability of PCL/TiO2 composites were characterized using thermogravimetric analysis (TGA). The initial weight loss (5 wt %) occurs at slightly higher temperature with micro and nano TiO2 addition and with increasing TiO2 content.
Abstract: Air conditioning is mainly use as human comfort
cooling medium. It use more in high temperatures are country such as
Malaysia. Proper estimation of cooling load will archive ideal
temperature. Without proper estimation can lead to over estimation or
under estimation. The ideal temperature should be comfort enough.
This study is to develop a program to calculate an ideal cooling load
demand, which is match with heat gain. Through this study, it is easy
to calculate cooling load estimation. Objective of this study are to
develop user-friendly and easy excess cooling load program. This is
to insure the cooling load can be estimate by any of the individual
rather than them using rule-of-thumb. Developed software is carryout
by using Matlab-GUI. These developments are only valid for
common building in Malaysia only. An office building was select as
case study to verify the applicable and accuracy of develop software.
In conclusion, the main objective has successfully where developed
software is user friendly and easily to estimate cooling load demand.
Abstract: Ethanol has been known for a long time, being
perhaps the oldest product obtained through traditional biotechnology
fermentation. Agriculture waste as substrate in fermentation is vastly
discussed as alternative to replace edible food and utilization of
organic material. Pineapple peel, highly potential source as substrate
is a by-product of the pineapple processing industry. Bio-ethanol
from pineapple (Ananas comosus) peel extract was carried out by
controlling fermentation without any treatment. Saccharomyces
ellipsoides was used as inoculum in this fermentation process as it is
naturally found at the pineapple skin. In this study, the capability of
Response Surface Methodology (RSM) for optimization of ethanol
production from pineapple peel extract using Saccharomyces
ellipsoideus in batch fermentation process was investigated. Effect of
five test variables in a defined range of inoculum concentration 6-
14% (v/v), pH (4.0-6.0), sugar concentration (14-22°Brix),
temperature (24-32°C) and time of incubation (30-54 hrs) on the
ethanol production were evaluated. Data obtained from experiment
were analyzed with RSM of MINITAB Software (Version 15)
whereby optimum ethanol concentration of 8.637% (v/v) was
determined. The optimum condition of 14% (v/v) inoculum
concentration, pH 6, 22°Brix, 26°C and 30hours of incubation. The
significant regression equation or model at the 5% level with
correlation value of 99.96% was also obtained.
Abstract: The excessive consumption of fossil energies (electrical energy) during summer caused by the technological development involves more and more climate warming.
In order to reduce the worst impact of gas emissions produced from classical air conditioning, heat driven solar absorption chiller is pretty promising; it consists on using solar as motive energy which is clean and environmentally friendly to provide cold.
Solar absorption machine is composed by four components using Lithium Bromide /water as a refrigerating couple. LiBr- water is the most promising in chiller applications due to high safety, high volatility ratio, high affinity, high stability and its high latent heat. The lithium bromide solution is constitute by the salt lithium bromide which absorbs water under certain conditions of pressure and temperature however if the concentration of the solution is high in the absorption chillers; which exceed 70%, the solution will crystallize.
The main aim of this article is to study the phenomena of the crystallization and to evaluate how the dependence between the electric conductivity and the concentration which should be controlled.
Abstract: Characterized as rich mineral substances, low
temperature, few bacteria, and stability with numerous implementation
aspects on aquaculture, food, drinking, and leisure, the deep sea water
(DSW) development has become a new industry in the world. It has
been report that marine algae contain various biologically active
compounds. This research focued on the affections in cultivating
Sagrassum cristaefolium with different concentration of deep sea
water(DSW) and surface sea water(SSW). After two and four weeks,
the total phenolic contents were compared in Sagrassum cristaefolium
culturing with different ways, and the reductive activity of them was
also be tried with potassium ferricyanide. Those fresh seaweeds were
dried with oven and were ground to powder. Progressively, the marine
algae we cultured was extracted by water under the condition with
heating them at 90Ôäâ for 1hr.The total phenolic contents were be
executed using Folin–Ciocalteu method. The results were explaining
as follows: the highest total phenolic contents and the best reductive
ability of all could be observed on the 1/4 proportion of DSW to SSW
culturing in two weeks. Furthermore, the 1/2 proportion of DSW to
SSW also showed good reductive ability and plentiful phenolic
compositions. Finally, we confirmed that difference proportion of
DSW and SSW is the major point relating to ether the total phenolic
components or the reductive ability in the Sagrassum cristaefolium. In
the future, we will use this way to mass production the marine algae or
other micro algae on industry applications.
Abstract: Tourism is a phenomenon respected by the human communities since a long time ago. It has been evoloving continually based on a variety of social and economic needs and with respect to increasingly development of communication and considerable increase of tourist-s number and resulted exchange income has attained much out come such as employment for the communities. or the purpose of tourism development in this zone suitable times and locations need to be specified in the zone for the tourist-s attendance. One of the most important needs of the tourists is the knowledge of climate conditions and suitable times for sightseeing. In this survey, the climate trend condition has been identified for attending the tourists in Isfahan province using the modified tourism climate index (TCI) as well as SPSS, GIS, excel, surfer softwares. This index evoluates systematically the climate conditions for tourism affairs and activities using the monthly maximum mean parameters of daily temperature, daily mean temperature, minimum relative humidity, daily mean relative humidity, precipitation (mm), total sunny hours, wind speed and dust. The results obtaind using kendal-s correlation test show that the months January, February, March, April, May, June, July, August, September, October, November and December are significant and have an increasing trend that indicates the best condition for attending the tourists. S, P, T mean , T max and dust are estimated from 1976-2005 and do kendal-s correlation test again to see which parameter has been effective. Based on the test, we also observed on the effective parameters that the rate of dust in February, March, April, May, June, July, August, October and November is decreasing and precipitation in September and January is increasing and also the radiation rate in May and August is increasing that indicate a better condition of convenience. Maximum temperature in June is also decreasing. Isfahan province has two spring and fall peaks and the best places for tourism are in the north and western areas.
Abstract: There is an ongoing controversy in the literature related
to the biological effects of weak, low frequency electromagnetic
fields. The physical arguments and interpretation of the experimental
evidence are inconsistent, where some physical arguments and
experimental demonstrations tend to reject the likelihood of any
effect of the fields at extremely low level. The problem arises of
explaining, how the low-energy influences of weak magnetic fields
can compete with the thermal and electrical noise of cells at normal
temperature using the theoretical studies. The magnetoreception in
animals involve radical pair mechanism. The same mechanism has
been shown to be involved in the circadian rhythm synchronization in
mammals. These reactions can be influenced by the weak magnetic
fields. Hence, it is postulated the biological clock can be affected
by weak magnetic fields and these disruptions to the rhythm can
cause adverse biological effects. In this paper, likelihood of altering
the biological clock via the radical pair mechanism is analyzed to
simplify these studies of controversy.
Abstract: Supercritical carbon dioxide (SC-CO2) was used as a
solvent to extract oil from wheat bran. Extractions were carried out in a
semi-batch process at temperatures ranging from 40 to 60ºC and
pressures ranging from 10 to 30 MPa, with a carbon dioxide (CO2)
flow rate of 26.81 g/min. The oil obtained from wheat bran at different
extraction conditions was quantitatively measured to investigate the
solubility of oil in SC-CO2. The solubility of wheat bran oil was found
to be enhanced in high temperature and pressure. The composition of
fatty acids in wheat bran oil was measured by gas chromatography
(GC). Linoleic, palmitic, oleic and γ-linolenic acid were the major
fatty acids of wheat bran oil. Tocopherol contents in oil were analyzed
by high performance liquid chromatography (HPLC). The highest
amount of phenolics and tocopherols (α and β) were found at
temperature of 60ºC and pressure of 30 MPa.
Abstract: Thermal water hammer is a special type of water
hammer which rarely occurs in heat exchangers. In biphasic fluids, if
steam bubbles are surrounded by condensate, regarding lower
condensate temperature than steam, they will suddenly collapse. As a
result, the vacuum caused by an extreme change in volume lead to
movement of the condensates in all directions and their collision the
force produced by this collision leads to a severe stress in the pipe
wall. This phenomenon is a special type of water hammer. According
to fluid mechanics, this phenomenon is a particular type of transient
flows during which abrupt change of fluid leads to sudden pressure
change inside the tube. In this paper, the mechanism of abrupt failure
of 80 tubes of 481 tubes of a methanol heat exchanger is discussed.
Initially, due to excessive temperature differences between heat
transfer fluids and simultaneous failure of 80 tubes, thermal shock
was presupposed as the reason of failure. Deeper investigation on
cross-section of failed tubes showed that failure was, ductile type of
failure, so the first hypothesis was rejected. Further analysis and more
accurate experiments revealed that failure of tubes caused by thermal
water hammer. Finally, the causes of thermal water hammer and
various solutions to avoid such mechanism are discussed.
Abstract: The design of methods of the 20 K large dimension cold shield used for infrared radiation demarcating in space environment simulation test were introduced in this paper. The cold shield were cooled by five G-M cryocoolers , and the dimension of the cold shield is the largest in our country.Cold shield installation and distribution and compensator for contraction on cooling were introduced detailedly. The temperature distribution and cool-down time of cold shield surface were also calculated and analysed in this paper. The design of cold shield resolves the difficulty of compensator for contraction on cooling successfully. Test results show that the actual technical performance indicators of cold shield met and exceeded the design requirements.
Abstract: The essential oil of M. × piperita L. was formulated
into a topical gel. The prepared gel was characterized for its pH,
viscosity, spreadiblity, consistency and extrudiblity, while its stability
was evaluated under different temperature conditions. The prepared
M. × piperita oil gel was clear and transparent. The pH value of
developed gel was 6.6, while its viscosity was 1200 cP. Spreadability
and consistency of the M. × piperita oil gel was 10.7 g.cm/sec and 7
mm, respectively. The prepared gel showed good extrudiblity. During
the stability studies, no significant change in pH and viscosity as a
function of time for gel was observed, indicating stability of prepared
formulation. The gel developed in this study is expected to forward
the usage of M. × piperita essential towards commercial application.
Abstract: In this study, the two dimensional heat conduction
problem for the dry friction clutch disc is modeled mathematically
analysis and is solved numerically using finite element method, to
determine the temperature field when band contacts occurs between
the rubbing surfaces during the operation of an automotive clutch.
Temperature calculation have been made for contact area of different
band width and the results obtained compared with these attained
when complete contact occurs. Furthermore, the effects of slipping
time and sliding velocity function are investigated as well. Both
single and repeated engagements made at regular interval are
considered.
Abstract: The influence of humidity and low temperature on the α- amylase activity and isoenzyme composition of grains of different wheat varieties have been studied. The identified samples of varieties have significant difference in the level of enzyme induction under the impact of high humidity and low temperature. It is proposed to use this methodological approach for testing genotypes and wheat breeding lines for resistance to pre-harvest sprouting (PHS).
Abstract: ORC (Organic Rankine Cycle) has potential of
reducing consumption of fossil fuels and has many favorable
characteristics to exploit low-temperature heat sources. In this work
thermodynamic performance of ORC with regeneration is
comparatively assessed for various working fluids. Special attention is
paid to the effects of system parameters such as the turbine inlet
pressure on the characteristics of the system such as net work
production, heat input, volumetric flow rate per 1 MW of net work and
quality of the working fluid at turbine exit as well as thermal
efficiency. Results show that for a given source the thermal efficiency
generally increases with increasing of the turbine inlet pressure
however has optimal condition for working fluids of low critical
pressure such as iso-pentane or n-pentane.
Abstract: In this work Membrane Distillation is applied to
concentrate orange Juice. Clarified orange juice (11o Brix) obtained
from fresh fruits and a sugar solution was subjected to membrane
distillation. The experiments were performed on a flat sheet module
using orange juice and sucrose solution as feeds. The concentration
of a sucrose solution, used as a model fruit juice and also orange
juice, was carried out in a direct contact membrane distillation using
hydrophobic PTFE membrane of pore size 0.2 μm and porosity 70%.
Surface modification of PTFE membrane has been carried out by
treating membrane with alcohol and water solution to make it
hydrophilic and then hydrophobicity was regained by drying. The
influences of the feed temperature, feed concentration, flow rate,
operating time on the permeate flux were studied for treated and non
treated membrane. In this work treated and non treated membrane
were compared in terms of water flux, Within the tested range, MD
with surface modified membrane the water flux has been
significantly improved by treating the membrane surface.
Abstract: The dilute acid pretreatment and enzymatic
saccharification of lignocellulosic substrate, cogon grass (Imperata
cylindrical, L.) was optimized prior ethanol fermentation using
simultaneous saccharification and fermentation (SSF) method. The
optimum pretreatment conditions, temperature, sulfuric acid
concentration, and reaction time were evaluated by determining the
maximum sugar yield at constant enzyme loading. Cogon grass, at
10% w/v substrate loading, has optimum pretreatment conditions of
126°C, 0.6% v/v H2SO4, and 20min reaction time. These
pretreatment conditions were used to optimize enzymatic
saccharification using different enzyme combinations. The maximum
saccharification yield of 36.68mg/mL (71.29% reducing sugar) was
obtained using 25FPU/g-cellulose cellulase complex combined with
1.1% w/w of cellobiase, ß-glucosidase, and 0.225% w/w of
hemicellulase complex, after 96 hours of saccharification. Using the
optimum pretreatment and saccharification conditions, SSF of treated
substrates was done at 37°C for 120 hours using industrial yeast
strain HBY3, Saccharomyces cerevisiae. The ethanol yield for cogon
grass at 4% w/w loading was 9.11g/L with 5.74mg/mL total residual
sugar.
Abstract: In this study, the sorption of Malachite green (MG) on Hydrilla verticillata biomass, a submerged aquatic plant, was investigated in a batch system. The effects of operating parameters such as temperature, adsorbent dosage, contact time, adsorbent size, and agitation speed on the sorption of Malachite green were analyzed using response surface methodology (RSM). The proposed quadratic model for central composite design (CCD) fitted very well to the experimental data that it could be used to navigate the design space according to ANOVA results. The optimum sorption conditions were determined as temperature - 43.5oC, adsorbent dosage - 0.26g, contact time - 200min, adsorbent size - 0.205mm (65mesh), and agitation speed - 230rpm. The Langmuir and Freundlich isotherm models were applied to the equilibrium data. The maximum monolayer coverage capacity of Hydrilla verticillata biomass for MG was found to be 91.97 mg/g at an initial pH 8.0 indicating that the optimum sorption initial pH. The external and intra particle diffusion models were also applied to sorption data of Hydrilla verticillata biomass with MG, and it was found that both the external diffusion as well as intra particle diffusion contributes to the actual sorption process. The pseudo-second order kinetic model described the MG sorption process with a good fitting.