Abstract: In this paper, the effect of addition the dune sand powder (DSP) on development of compressive strength and hydration of cement pastes was investigated as a function of water/binder ratio, was varied, on the one hand, the percentage of DSP and on the other, the fineness of DSP. In order to understand better the pozzolanic effect of dune sand powder in cement pastes, we followed the mixtures hydration (50% Pure Lime + 50% DSP) by X-ray diffraction. These mixtures the pastes present a hydraulic setting which is due to the formation of a C-S-H phase (calcium silicate hydrate). The latter is semi-crystallized. This study is a simplified approach to that of the mixtures (80% ordinary Portland cement + 20% DSP), in which the main reaction is the fixing of the lime coming from the cement hydration in the presence of DSP, to form calcium silicate hydrate semi-crystallized of second generation. The results proved that up to (20% DSP) as Portland cement replacement could be used with a fineness of 4000 cm²/g without affecting adversely the compressive strength. After 28 days, the compressive strength at 5, 10 and 15% DSP is superior to Portland cement, with an optimum effect for a percentage of the order of 5% to 10% irrespective of the w/b ratio and fineness of DSP.
Abstract: Study of fire and explosion is very important mainly
in oil and gas industries due to several accidents which have been
reported in the past and present. In this work, we have investigated
the flammability of bio oil vapour mixtures. This mixture may
contribute to fire during the storage and transportation process. Bio
oil sample derived from Palm Kernell shell was analysed using Gas
Chromatography Mass Spectrometry (GC-MS) to examine the
composition of the sample. Mole fractions of 12 selected
components in the liquid phase were obtained from the GC-FID data
and used to calculate mole fractions of components in the gas phase
via modified Raoult-s law. Lower Flammability Limits (LFLs) and
Upper Flammability Limits (UFLs) for individual components were
obtained from published literature. However, stoichiometric
concentration method was used to calculate the flammability limits
of some components which their flammability limit values are not
available in the literature. The LFL and UFL values for the mixture
were calculated using the Le Chatelier equation. The LFLmix and
UFLmix values were used to construct a flammability diagram and
subsequently used to determine the flammability of the mixture. The
findings of this study can be used to propose suitable inherently
safer method to prevent the flammable mixture from occurring and
to minimizing the loss of properties, business, and life due to fire
accidents in bio oil productions.
Abstract: Independent component analysis can estimate unknown
source signals from their mixtures under the assumption that the
source signals are statistically independent. However, in a real environment,
the separation performance is often deteriorated because
the number of the source signals is different from that of the sensors.
In this paper, we propose an estimation method for the number of
the sources based on the joint distribution of the observed signals
under two-sensor configuration. From several simulation results, it
is found that the number of the sources is coincident to that of
peaks in the histogram of the distribution. The proposed method can
estimate the number of the sources even if it is larger than that of
the observed signals. The proposed methods have been verified by
several experiments.
Abstract: Due to urbanization, trees and plants which covered a great land mass of the earth and are an excellent carbon dioxide (CO2) absorber through photosynthesis are being replaced by several concrete based structures. It is therefore important to have these cement based structures absorb the large volume of carbon dioxide which the trees would have removed from the atmosphere during their useful lifespan. Hence the need for these cement based structures to be designed to serve other useful purposes in addition to shelter. This paper reviews the properties of Sodium carbonate and sugar as admixtures in concrete with respect to improving carbon sequestration in concrete.
Abstract: Studying alternative raw materials for biodiesel production is of major importance. The use of mixtures with incorporation of wastes is an environmental friendly alternative and might reduce biodiesel production costs. The objective of the present work was: (i) to study biodiesel production using waste frying oil mixed with pork lard and (ii) to understand how mixture composition influences biodiesel quality. Biodiesel was produced by transesterification and quality was evaluated through determination of several parameters according to EN 14214. The weight fraction of lard in the mixture varied from 0 to 1 in 0.2 intervals. Biodiesel production yields varied from 81.7 to 88.0 (wt%), the lowest yields being the ones obtained using waste frying oil and lard alone as raw materials. The obtained products fulfilled most of the determined quality specifications according to European biodiesel quality standard EN 14214. Minimum purity (96.5 wt%) was closely obtained when waste frying oil was used alone and when 0.2% of lard was incorporated in the raw material (96.3 wt%); however, it ranged from 93.9 to 96.3 (wt%) being always close to the limit. From the evaluation of the influence of mixture composition in biodiesel quality, it was possible to establish a model to be used for predicting some parameters of biodiesel resulting from mixtures of waste frying oil with lard when different lard contents are used.
Abstract: The pyrolysis of hazelnut shell, polyethylene oxide and their blends were carried out catalytically at 500 and 650 ºC. Potassium dichromate was chosen according to its oxidative characteristics and decomposition temperature (500 ºC) where decomposition products are CrO3 and K2CrO4. As a main effect, a remarkable increase in gasification was observed using this catalyst for pure components and blends especially at 500 ºC rather than 650 ºC contrary to the main observation in the pyrolysis process. The increase in gas product quantity was compensated mainly with decrease in solid product and additionally in some cases liquid products.
Abstract: Attempt was made to improve certain characteristics of bio-oil derived from palm kernel pyrolysis by blending it with diesel fuel and alcohols. Two types of alcohol, ethanol or butanol, was used as cosolvent to stabilize the phase of ternary systems. Phase behaviors and basic fuel properties of palm kernel bio-oildiesel- alcohol systems were investigated in this study. Alcohol types showed a significant influence on the phase characteristics with palm kernel bio-oil-diesel-butanol system giving larger soluble area than that of palm kernel bio-oil-diesel-ethanol system. For fuel properties, blended fuels showed superior properties including lower values of density (~860 kg/m3 at 25°C), viscosity (~4.12 mm2/s at 40°C), carbon residue (1.02-2.53 wt%), ash (0.018-0.034 wt%) and pour point (
Abstract: The usefulness of weaning foods to meet the nutrient
needs of children is well recognized, and most of them are precooked
roller dried mixtures of cereal and/or legume flours which posses a
high viscosity and bulk when reconstituted. The objective of this study
was to formulate composite weaning foods using cereals, malted
legumes and vegetable powders and analyze them for nutrients,
functional properties and sensory attributes. Selected legumes (green
gram and lentil) were germinated, dried and dehulled. Roasted wheat,
rice, carrot powder and skim milk powder also were used. All the
ingredients were mixed in different proportions to get four
formulations, made into 30% slurry and dried in roller drier. The
products were analyzed for proximate principles, mineral content,
functional and sensory qualities. The results of analysis showed
following range of constituents per 100g of formulations on dry
weight basis, protein, 18.1-18.9 g ; fat, 0.78-1.36 g ; iron, 5.09-6.53
mg; calcium, 265-310 mg. The lowest water absorption capacity was
in case of wheat green gram based and the highest was in rice lentil
based sample. Overall sensory qualities of all foods were graded as
“good" and “very good" with no significant differences. The results
confirm that formulated weaning foods were nutritionally superior,
functionally appropriate and organoleptically acceptable.
Abstract: In order to supplement the brittle property of concrete,
fibers are added into concrete mixtures. Compared to general concrete,
various characteristics such as tensile strength, bending strength,
bending toughness, and resistance to crack are superior, and even
when cracks occur, improvements on toughness as well as resistance
to shock are excellent due to the growth of fracture energy. Increased
function of steel fiber reinforced concrete can be differentiated
depending on the fiber dispersion, and sand percentage can be an
important influence on the fiber dispersion. Therefore, in this research,
experiments were planned on sand percentage in order to apprehend
the influence of sand percentage on the bending properties and direct
tension of SFRC and basic experiments were conducted on bending
and direct tension in order to recognize the properties of bending
properties and direct tension following the size of the aggregates and
sand percentage.
Abstract: As the fossil fuels kept on depleting, intense research in developing hydrogen (H2) as the alternative fuel has been done to cater our tremendous demand for fuel. The potential of H2 as the ultimate clean fuel differs with the fossil fuel that releases significant amounts of carbon dioxide (CO2) into the surrounding and leads to the global warming. The experimental work was carried out to study the production of H2 from palm kernel shell steam gasification at different variables such as heating rate, steam to biomass ratio and adsorbent to biomass ratio. Maximum H2 composition which is 61% (volume basis) was obtained at heating rate of 100oCmin-1, steam/biomass of 2:1 ratio, and adsorbent/biomass of 1:1 ratio. The commercial adsorbent had been modified by utilizing the alcoholwater mixture. Characteristics of both adsorbents were investigated and it is concluded that flowability and floodability of modified CaO is significantly improved.
Abstract: This paper presents development of an ignition system using spark electrodes for application in a research explosion vessel.
A single spark is aimed to be discharged with quantifiable ignition energy. The spark electrode system would enable study of flame
propagation, ignitability of fuel-air mixtures and other fundamental characteristics of flames. The principle of the capacitive spark circuit
of ASTM is studied to charge an appropriate capacitance connected across the spark gap through a large resistor by a high voltage from
the source of power supply until the initiation of spark. Different spark energies could be obtained mainly by varying the value of the
capacitance and the supply current. The spark sizes produced are found to be affected by the spark gap, electrode size, input voltage
and capacitance value.
Abstract: In the modern construction practices, industrial wastes
or by-products are largely used as raw materials in cement and
concrete. These impart many benefits to the environment and bringabout
an economic impact because the cost of waste disposal is
constantly increasing due to strict environmental regulations. It was
reported in literature that the leakage of oil onto concrete element in
older cement grinding unit resulted in concrete with greater resistance
to freezing and thawing. This effect was thought to be similar to
adding an air-entraining chemical admixture to concrete. This paper
presents an investigation on the load deflection behaviour and crack
patterns of reinforced concrete (RC) beams subjected to four point
loading. Ten 120x260x1900 mm beams were cast with 100%
ordinary Portland cement (OPC) concrete, 20% fly ash (FA) and 20%
rice husk ash (RHA) blended cement concrete. 0.15% dosage of
admixtures (used engine oil, new engine oil, and superplasticizer)
was used throughout the experiment. Results show that OPC and
OPC/RHA RC beams containing used engine oil and superplasticizer
exhibit higher capacity, 18-26% than their corresponding control
mix.
Abstract: A highly optimized implementation of binary mixture
diffusion with no initial bulk velocity on graphics processors is
presented. The lattice Boltzmann model is employed for simulating
the binary diffusion of oxygen and nitrogen into each other with
different initial concentration distributions. Simulations have been
performed using the latest proposed lattice Boltzmann model that
satisfies both the indifferentiability principle and the H-theorem for
multi-component gas mixtures. Contemporary numerical
optimization techniques such as memory alignment and increasing
the multiprocessor occupancy are exploited along with some novel
optimization strategies to enhance the computational performance on
graphics processors using the C for CUDA programming language.
Speedup of more than two orders of magnitude over single-core
processors is achieved on a variety of Graphical Processing Unit
(GPU) devices ranging from conventional graphics cards to
advanced, high-end GPUs, while the numerical results are in
excellent agreement with the available analytical and numerical data
in the literature.
Abstract: The effect of dry milling on the carbothermic
reduction of celestite was investigated. Mixtures of celestite
concentrate (98% SrSO4) and activated carbon (99% carbon) was
milled for 1 and 24 hours in a planetary ball mill. Un-milled and
milled mixtures and their products after carbothermic reduction were
studied by a combination of XRD and TGA/DTA experiments. The
thermogravimetric analyses and XRD results showed that by milling
celestite-carbon mixtures for one hour, the formation temperature of
strontium sulfide decreased from about 720°C (in un-milled sample)
to about 600°C, after 24 hours milling it decreased to 530°C. It was
concluded that milling induces increasingly thorough mixing of the
reactants to reduction occurring at lower temperatures
Abstract: The studies concerned an effect of six variants of ion
exchange substrate (nutrient carriers with a different potential impact
on pH of soil solution) on vegetation of orchard grass during two
different periods (42 and 84 days). In the pot experiment plants were
grown on sand (model of degraded soil) and six mixtures of sand and
2% (v/v) additions of particular variants of ion exchange substrate
(with pH ranged from 5.5 to 8.0). The study results showed that the
addition of the substrate at pH=6.5 caused the highest increase in
plant yield after shorter vegetation period whereas the addition of the
substrate at pH=5.5 increased dry stem and root biomass of orchard
grass after longer vegetation period. Thus, the ion exchange substrate
at pH=6.5 can be recommended for restoration of exhausted soils
when shorter vegetation period is planned; the ion exchange substrate
at pH=5.5 can be used for the same purpose when longer periods of
vegetative growth are considered.
Abstract: Cements, which are intrinsically brittle materials, can
exhibit a degree of pseudo-ductility when reinforced with a sufficient
volume fraction of a fibrous phase. This class of materials, called
Engineered Cement Composites (ECC) has the potential to be used in
future tunneling applications where a level of pseudo-ductility is
required to avoid brittle failures. However uncertainties remain
regarding mechanical performance. Previous work has focused on
comparatively thin specimens; however for future civil engineering
applications, it is imperative that the behavior in tension of thicker
specimens is understood. In the present work, specimens containing
cement powder and admixtures have been manufactured following
two different processes and tested in tension. Multiple matrix
cracking has been observed during tensile testing, leading to a
“strain-hardening" behavior, confirming the possible suitability of
ECC material when used as thick sections (greater than 50mm) in
tunneling applications.
Abstract: Climate change and environmental pressures are
major international issues nowadays. It is time when governments,
businesses and consumers have to respond through more
environmentally friendly and aware practices, products and policies.
This is the prime time to develop alternative sustainable construction
materials, reduce greenhouse gas emissions, save energy, look to
renewable energy sources and recycled materials, and reduce waste.
The utilization of waste materials (slag, fly ash, glass beads, plastic
and so on) in concrete manufacturing is significant due to its
engineering, financial, environmental and ecological benefits. Thus,
utilization of waste materials in concrete production is very much
helpful to reach the goal of the sustainable construction. Therefore,
this study intends to use glass beads in concrete production.
The paper reports on the performance of 9 different concrete
mixes containing different ratios of glass crushed to 5 mm - 20 mm
maximum size and glass marble of 20 mm size as coarse aggregate.
Ordinary Portland cement type 1 and fine sand less than 0.5 mm were
used to produce standard concrete cylinders. Compressive strength
tests were carried out on concrete specimens at various ages. Test
results indicated that the mix having the balanced ratio of glass beads
and round marbles possess maximum compressive strength which is
3889 psi, as glass beads perform better in bond formation but have
lower strength, on the other hand marbles are strong in themselves
but not good in bonding. These mixes were prepared following a
specific W/C and aggregate ratio; more strength can be expected to
achieve from different W/C, aggregate ratios, adding admixtures like
strength increasing agents, ASR inhibitor agents etc.
Abstract: Utilization of waste material in asphalt pavement
would be beneficial in order to find an alternative solution to increase
service life of asphalt pavement and reduce environmental pollution
as well. One of these waste materials is Polyethylene Terephthalate
(PET) which is a type of polyester material and is produced in a large
extent. This research program is investigating the effects of adding
waste PET particles into the asphalt mixture with a maximum size of
2.36 mm. Different percentages of PET were added into the mixture
during dry process. Gap-graded mixture (SMA 14) and PG 80-100
asphalt binder have been used for this study. To evaluate PET
reinforced asphalt mixture different laboratory investigations have
been conducted on specimens. Marshall Stability test was carried
out. Besides, stiffness modulus test and indirect tensile fatigue test
were conducted on specimens at optimum asphalt content. It was
observed that in many cases PET reinforced SMA mixture had better
mechanical properties in comparison with control mixture.
Abstract: In this study two series of self compacting concrete
mixtures were prepared with 100% coarse recycled concrete
aggregates and different percentages of 0%, 20%, 40%, 60%, 80%
and 100% fine recycled concrete aggregates. In series I and II the
water to binder ratios were 0.50 and 0.45, respectively. The cement
content was kept 350
3 m
kg for those mixtures that don't have any
Nano-Silica. To improve the compressive strength of samples, Nano-
Silica replaced with 10% of cement weight in concrete mixtures. By
doing the tests, the results showed that, adding Nano-silica to the
samples with less percentage of fine recycled concrete aggregates,
lead to more increase on the compressive strength.
Abstract: Limited infrastructure development on peats and
organic soils is a serious geotechnical issues common to many
countries of the world especially Malaysia which distributed 1.5 mill
ha of those problematic soil. These soils have high water content and
organic content which exhibit different mechanical properties and
may also change chemically and biologically with time. Constructing
structures on peaty ground involves the risk of ground failure and
extreme settlement. Nowdays, much efforts need to be done in
making peatlands usable for construction due to increased landuse.
Deep mixing method employing cement as binders, is generally used
as measure again peaty/ organic ground failure problem. Where the
technique is widely adopted because it can improved ground
considerably in a short period of time. An understanding of
geotechnical properties as shear strength, stiffness and compressibility
behavior of these soils was requires before continues construction on
it. Therefore, 1- 1.5 meter peat soil sample from states of Johor and
an organic soil from Melaka, Malaysia were investigated. Cement
were added to the soil in the pre-mixing stage with water cement ratio
at range 3.5,7,14,140 for peats and 5,10,30 for organic soils,
essentially to modify the original soil textures and properties. The
mixtures which in slurry form will pour to polyvinyl chloride (pvc)
tube and cured at room temperature 250C for 7,14 and 28 days.
Laboratory experiments were conducted including unconfined
compressive strength and bender element , to monitor the improved
strength and stiffness of the 'stabilised mixed soils'. In between,
scanning electron miscroscopic (SEM) were observations to
investigate changes in microstructures of stabilised soils and to
evaluated hardening effect of a peat and organic soils stabilised
cement. This preliminary effort indicated that pre-mixing peat and
organic soils contributes in gaining soil strength while help the
engineers to establish a new method for those problematic ground
improvement in further practical and long term applications.