Abstract: Research results and optimal parameters investigation
of laser cut and profiling of diamond and quartz substrates by
femtosecond laser pulses are presented. Profiles 10 μm in width, ~25
μm in depth and several millimeters long were made. Investigation of
boundaries quality has been carried out with the use of AFM
«Vecco». Possibility of technological formation of profiles and
micro-holes in diamond and quartz substrates with nanometer-scale
boundaries is shown. Experimental results of multilayer dielectric
cover treatment are also presented. Possibility of precise upper layer
(thickness of 70–140 nm) removal is demonstrated. Processes of thin
metal film (60 nm and 350 nm thick) treatment are considered.
Isolation tracks (conductance ~ 10-11 S) 1.6–2.5 μm in width in
conductive metal layers are formed.
Abstract: This paper tries to study the effect of geosynthetic inclusion on the improvement of the load-settlement characters of two layered soil. In addition, the effect of geogrid and geotextile in reduction of the required thickness of subbase layer in unpaved roads is studied. Considering the vast application of bearing ratio tests in road construction projects, this test is used in present investigation. Bearing ratio tests were performed on two layered soil including a granular soil layer at the top (as the subbase layer) and a weak clayey soil placed at the bottom (as the subgrade layer). These tests were performed for different conditions including unreinforced and reinforced by geogrid and geotextile and three thicknesses for top layer soil (subbase layer). In the reinforced condition the reinforcing element was placed on the interface of the top granular layer and the beneath clayey layer to study the separation effect of geosynthetics. In all tests the soils (both granular and clayey soil layers) were compacted according to optimum water content. At the end, the diagrams were plotted and were compared with each other. Furthermore, a comparison between geogrids and geotextiles behaviors on two layer soil is done in this paper. The results show an increase in compression strength of reinforced specimen in comparison with unreinforced soil sample. The effect of geosynthetic inclusion reduces by increasing the subbase thickness. In addition it was found that geogrids have more desirable behavior rather than geotextiles due to interlocking with the subbase layer aggregates.
Abstract: This paper adopted the hybrid differential transform approach for studying heat transfer problems in a gold/chromium thin film with an ultra-short-pulsed laser beam projecting on the gold side. The physical system, formulated based on the hyperbolic two-step heat transfer model, covers three characteristics: (i) coupling effects between the electron/lattice systems, (ii) thermal wave propagation in metals, and (iii) radiation effects along the interface. The differential transform method is used to transfer the governing equations in the time domain into the spectrum equations, which is further discretized in the space domain by the finite difference method. The results, obtained through a recursive process, show that the electron temperature in the gold film can rise up to several thousand degrees before its electron/lattice systems reach equilibrium at only several hundred degrees. The electron and lattice temperatures in the chromium film are much lower than those in the gold film.
Abstract: In this paper, for the first time, a two-dimensional
(2D) analytical drain current model for sub-100 nm multi-layered
gate material engineered trapezoidal recessed channel (MLGMETRC)
MOSFET: a novel design is presented and investigated using
ATLAS and DEVEDIT device simulators, to mitigate the large gate
leakages and increased standby power consumption that arise due to
continued scaling of SiO2-based gate dielectrics. The twodimensional
(2D) analytical model based on solution of Poisson-s
equation in cylindrical coordinates, utilizing the cylindrical
approximation, has been developed which evaluate the surface
potential, electric field, drain current, switching metric: ION/IOFF
ratio and transconductance for the proposed design. A good
agreement between the model predictions and device simulation
results is obtained, verifying the accuracy of the proposed analytical
model.
Abstract: Conventionally the selection of parameters depends
intensely on the operator-s experience or conservative technological
data provided by the EDM equipment manufacturers that assign
inconsistent machining performance. The parameter settings given by
the manufacturers are only relevant with common steel grades. A
single parameter change influences the process in a complex way.
Hence, the present research proposes artificial neural network (ANN)
models for the prediction of surface roughness on first commenced
Ti-15-3 alloy in electrical discharge machining (EDM) process. The
proposed models use peak current, pulse on time, pulse off time and
servo voltage as input parameters. Multilayer perceptron (MLP) with
three hidden layer feedforward networks are applied. An assessment
is carried out with the models of distinct hidden layer. Training of the
models is performed with data from an extensive series of
experiments utilizing copper electrode as positive polarity. The
predictions based on the above developed models have been verified
with another set of experiments and are found to be in good
agreement with the experimental results. Beside this they can be
exercised as precious tools for the process planning for EDM.
Abstract: Coronary artery bypass grafts (CABG) are widely
studied with respect to hemodynamic conditions which play
important role in presence of a restenosis. However, papers which
concern with constitutive modeling of CABG are lacking in the
literature. The purpose of this study is to find a constitutive model for
CABG tissue. A sample of the CABG obtained within an autopsy
underwent an inflation–extension test. Displacements were
recoredered by CCD cameras and subsequently evaluated by digital
image correlation. Pressure – radius and axial force – elongation
data were used to fit material model. The tissue was modeled as onelayered
composite reinforced by two families of helical fibers. The
material is assumed to be locally orthotropic, nonlinear,
incompressible and hyperelastic. Material parameters are estimated
for two strain energy functions (SEF). The first is classical
exponential. The second SEF is logarithmic which allows
interpretation by means of limiting (finite) strain extensibility.
Presented material parameters are estimated by optimization based
on radial and axial equilibrium equation in a thick-walled tube. Both
material models fit experimental data successfully. The exponential
model fits significantly better relationship between axial force and
axial strain than logarithmic one.
Abstract: In this paper, multilayered coreless printed circuit
board (PCB) step-down power transformers for DC-DC converter
applications have been designed, manufactured and evaluated. A set
of two different circular spiral step-down transformers were
fabricated in the four layered PCB. These transformers have been
modelled with the assistance of high frequency equivalent circuit and
characterized with both sinusoidal and square wave excitation. This
paper provides the comparative results of these two different
transformers in terms of their resistances, self, leakage, mutual
inductances, coupling coefficient and also their energy efficiencies.
The operating regions for optimal performance of these transformers
for power transfer applications are determined. These transformers
were tested for the output power levels of about 30 Watts within the
input voltage range of 12-50 Vrms. The energy efficiency for these
step down transformers is observed to be in the range of 90%-97% in
MHz frequency region.
Abstract: The mechanical properties including flexural and
tensile of neat vinyl ester and polymer based on layered silicate
nanocomposite materials are discussed. The addition of layered
silicate into the polymer matrix increased the tensile and flexural
modulus up to 1 wt.% clay loading. The incorporation of more clay
resulted in decreasing the mechanical properties which was traced to
the existence of aggregation layers. Likewise, up to 1 wt.% clay
loading, the thermal behaviour showed significant improvements and
at higher clay loading the thermal pattern was reduced. The
aggregation layers imparted a negative impact on the overall
mechanical and thermal properties. Wide Angle X-ray Diffraction,
Scanning Electron Microscopy and Transmission Electron
Microscopy were utilised in order to characterise the interlamellar
structure of nanocomposites.
Abstract: The Multi-Layered Perceptron (MLP) Neural
networks have been very successful in a number of signal processing
applications. In this work we have studied the possibilities and the
met difficulties in the application of the MLP neural networks for the
prediction of daily solar radiation data. We have used the Polack-Ribière algorithm for training the neural networks. A comparison, in
term of the statistical indicators, with a linear model most used in
literature, is also performed, and the obtained results show that the
neural networks are more efficient and gave the best results.
Abstract: The speech signal conveys information about the
identity of the speaker. The area of speaker identification is
concerned with extracting the identity of the person speaking the
utterance. As speech interaction with computers becomes more
pervasive in activities such as the telephone, financial transactions
and information retrieval from speech databases, the utility of
automatically identifying a speaker is based solely on vocal
characteristic. This paper emphasizes on text dependent speaker
identification, which deals with detecting a particular speaker from a
known population. The system prompts the user to provide speech
utterance. System identifies the user by comparing the codebook of
speech utterance with those of the stored in the database and lists,
which contain the most likely speakers, could have given that speech
utterance. The speech signal is recorded for N speakers further the
features are extracted. Feature extraction is done by means of LPC
coefficients, calculating AMDF, and DFT. The neural network is
trained by applying these features as input parameters. The features
are stored in templates for further comparison. The features for the
speaker who has to be identified are extracted and compared with the
stored templates using Back Propogation Algorithm. Here, the
trained network corresponds to the output; the input is the extracted
features of the speaker to be identified. The network does the weight
adjustment and the best match is found to identify the speaker. The
number of epochs required to get the target decides the network
performance.
Abstract: In the present work, we propose a new technique to
enhance the learning capabilities and reduce the computation
intensity of a competitive learning multi-layered neural network
using the K-means clustering algorithm. The proposed model use
multi-layered network architecture with a back propagation learning
mechanism. The K-means algorithm is first applied to the training
dataset to reduce the amount of samples to be presented to the neural
network, by automatically selecting an optimal set of samples. The
obtained results demonstrate that the proposed technique performs
exceptionally in terms of both accuracy and computation time when
applied to the KDD99 dataset compared to a standard learning
schema that use the full dataset.
Abstract: Bandwidth allocation in wired network is less complex
and to allocate bandwidth in wireless networks is complex and
challenging, due to the mobility of source end system.This paper
proposes a new approach to bandwidth allocation to higher and lower
priority mobile nodes.In our proposal bandwidth allocation to new
mobile node is based on bandwidth utilization of existing mobile
nodes.The first section of the paper focuses on introduction to
bandwidth allocation in wireless networks and presents the existing
solutions available for allocation of bandwidth. The second section
proposes the new solution for the bandwidth allocation to higher and
lower priority nodes. Finally this paper ends with the analytical
evaluation of the proposed solution.
Abstract: This paper presents a video transmission system using
layered multiple description (coding (MDC) and multi-path transport
for reliable video communications in wireless ad-hoc networks.
The proposed MDC extends a quality-scalable H.264/AVC video
coding algorithm to generate two independent descriptions. The two
descriptions are transmitted over different paths to a receiver in order
to alleviate the effect of unstable channel conditions of wireless adhoc
networks. If one description is lost due to transmission erros,
then the correctly received description is used to estimate the lost
information of the corrupted description. The proposed MD coder
maintains an adequate video quality as long as both description are
not simultaneously lost. Simulation results show that the proposed
MD coding combined with multi-path transport system is largely
immune to packet losses, and therefore, can be a promising solution
for robust video communications over wireless ad-hoc networks.
Abstract: This study presents the application of artificial
neural network for modeling the phenolic compound
migration through vertical soil column. A three layered feed
forward neural network with back propagation training
algorithm was developed using forty eight experimental data
sets obtained from laboratory fixed bed vertical column tests.
The input parameters used in the model were the influent
concentration of phenol(mg/L) on the top end of the soil
column, depth of the soil column (cm), elapsed time after
phenol injection (hr), percentage of clay (%), percentage of
silt (%) in soils. The output of the ANN was the effluent
phenol concentration (mg/L) from the bottom end of the soil
columns. The ANN predicted results were compared with the
experimental results of the laboratory tests and the accuracy of
the ANN model was evaluated.
Abstract: Image convolution similar to the receptive fields
found in mammalian visual pathways has long been used in
conventional image processing in the form of Gabor masks.
However, no VLSI implementation of parallel, multi-layered pulsed
processing has been brought forward which would emulate this
property. We present a technical realization of such a pulsed image
processing scheme. The discussed IC also serves as a general testbed
for VLSI-based pulsed information processing, which is of interest
especially with regard to the robustness of representing an analog
signal in the phase or duration of a pulsed, quasi-digital signal, as
well as the possibility of direct digital manipulation of such an
analog signal. The network connectivity and processing properties
are reconfigurable so as to allow adaptation to various processing
tasks.
Abstract: Workload and resource management are two essential functions provided at the service level of the grid software infrastructure. To improve the global throughput of these software environments, workloads have to be evenly scheduled among the available resources. To realize this goal several load balancing strategies and algorithms have been proposed. Most strategies were developed in mind, assuming homogeneous set of sites linked with homogeneous and fast networks. However for computational grids we must address main new issues, namely: heterogeneity, scalability and adaptability. In this paper, we propose a layered algorithm which achieve dynamic load balancing in grid computing. Based on a tree model, our algorithm presents the following main features: (i) it is layered; (ii) it supports heterogeneity and scalability; and, (iii) it is totally independent from any physical architecture of a grid.
Abstract: Commercial nanocomposite food packaging type nano-silver containers were characterised using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The presence of nanoparticles consistent with the incorporation of 1% nano-silver (Ag) and 0.1% titanium dioxide (TiO2) nanoparticle into polymeric materials formed into food containers was confirmed. Both nanomaterials used in this type of packaging appear to be embedded in a layered configuration within the bulk polymer. The dimensions of the incorporated nanoparticles were investigated using X-ray diffraction (XRD) and determined by calculation using the Scherrer Formula; these were consistent with Ag and TiO2 nanoparticles in the size range 20-70nm both were spherical shape nanoparticles. Antimicrobial assessment of the nanocomposite container has also been performed and the results confirm the antimicrobial activity of Ag and TiO2 nanoparticles in food packaging containers. Migration assessments were performed in a wide range of food matrices to determine the migration of nanoparticles from the packages. The analysis was based upon the relevant European safety Directives and involved the application of inductively coupled plasma mass spectrometry (ICP-MS) to identify the range of migration risk. The data pertain to insignificance levels of migration of Ag and TiO2 nanoparticles into the selected food matrices.
Abstract: The process of laser absorption in the skin during
laser irradiation was a critical point in medical application
treatments. Delivery the correct amount of laser light is a critical
element in photodynamic therapy (PDT). More amounts of laser
light able to affect tissues in the skin and small amount not able to
enhance PDT procedure in skin. The knowledge of the skin tone
laser dependent distribution of 635 nm radiation and its penetration
depth in skin is a very important precondition for the investigation of
advantage laser induced effect in (PDT) in epidermis diseases
(psoriasis). The aim of this work was to estimate an optimum effect
of diode laser (635 nm) on the treatment of epidermis diseases in
different color skin. Furthermore, it is to improve safety of laser in
PDT in epidermis diseases treatment. Advanced system analytical
program (ASAP) which is a new approach in investigating the PDT,
dependent on optical properties of different skin color was used in
present work. A two layered Realistic Skin Model (RSM); stratum
corneum and epidermal with red laser (635 nm, 10 mW) were used
for irradiative transfer to study fluence and absorbance in different
penetration for various human skin colors. Several skin tones very
fair, fair, light, medium and dark are used to irradiative transfer. This
investigation involved the principles of laser tissue interaction when
the skin optically injected by a red laser diode. The results
demonstrated that the power characteristic of a laser diode (635 nm)
can affect the treatment of epidermal disease in various color skins.
Power absorption of the various human skins were recorded and
analyzed in order to find the influence of the melanin in PDT
treatment in epidermal disease. A two layered RSM show that the
change in penetration depth in epidermal layer of the color skin has a
larger effect on the distribution of absorbed laser in the skin; this is
due to the variation of the melanin concentration for each color.
Abstract: Thermal load calculations have been performed for
multi-layered walls that are composed of three different parts; a
common (sand and cement) plaster, and two types of locally
produced soft and hard bricks. The masonry construction of these
layered walls was based on concrete-backed stone masonry made of
limestone bricks joined by mortar. These multilayered walls are
forming the outer walls of the building envelope of a typical Libyan
house. Based on the periodic seasonal weather conditions, within the
Libyan cost region during summer and winter, measured thermal
conductivity values were used to implement such seasonal variation
of heat flow and the temperature variations through the walls. The
experimental measured thermal conductivity values were obtained
using the Hot Disk technique. The estimation of the thermal
resistance of the wall layers ( R-values) is based on measurements
and calculations. The numerical calculations were done using a
simplified analytical model that considers two different wall
constructions which are characteristics of such houses. According to
the obtained results, the R-values were quite low and therefore,
several suggestions have been proposed to improve the thermal
loading performance that will lead to a reasonable human comfort
and reduce energy consumption.
Abstract: To measure the thickness of the subcutaneous adipose
tissue layer, a non-invasive optical measurement system (λ=1300 nm)
is introduced. Animal and human subjects are used for the
experiments. The results of human subjects are compared with the data
of ultrasound device measurements, and a high correlation (r=0.94 for
n=11) is observed. There are two modes in the corresponding signals
measured by the optical system, which can be explained by
two-layered and three-layered tissue models. If the target tissue is
thinner than the critical thickness, detected data using diffuse
reflectance method follow the three-layered tissue model, so the data
increase as the thickness increases. On the other hand, if the target
tissue is thicker than the critical thickness, the data follow the
two-layered tissue model, so they decrease as the thickness increases.