Abstract: Having considered tactile sensing and palpation of a
surgeon in order to detect kidney stone during open surgery; we
present the 2D model of nephrolithiasis (two dimensional model of
kidney containing a simulated stone). The effects of stone existence
that appear on the surface of kidney (because of exerting mechanical
load) are determined. Using Finite element method, it is illustrated
that the created stress patterns on the surface of kidney and stress
graphs not only show existence of stone inside kidney, but also show
its exact location.
Abstract: Manufacturing components of fiber-reinforced
thermoplastics requires three steps: heating the matrix, forming and
consolidation of the composite and terminal cooling the matrix. For
the heating process a pre-determined temperature distribution through
the layers and the thickness of the pre-consolidated sheets is
recommended to enable forming mechanism. Thus, a design for the
heating process for forming composites with thermoplastic matrices
is necessary. To obtain a constant temperature through thickness and
width of the sheet, the heating process was analyzed by the help of
the finite element method. The simulation models were validated by
experiments with resistance thermometers as well as with an infrared
camera. Based on the finite element simulation, heating methods for
infrared radiators have been developed. Using the numeric
simulation many iteration loops are required to determine the process
parameters. Hence, the initiation of a model for calculating relevant
process parameters started applying regression functions.
Abstract: The aim of this paper is the analysis and preservation of lime kilns, focusing on the structure, construction, and functionality of vertical shaft lime kilns of the Cap Corse in Corsica. Plans and sections of two lime kilns are presented in detail, providing an overall picture of this specific industrial heritage. The potential damage areas are identified performing structural analysis of a lime kiln using the finite element method. A restoration and strengthening technique that satisfies the directions of the Charter of Venice is presented using post-tensioning tendons. Recommendations are given to preserve and promote these important historical structures integrating them into the custom footpath.
Abstract: This paper presents the simulation the results of
electric field and potential distributions along surface of silicone
rubber polymer insulators. Near the same leakage distance subjected
to 15 kV in 50 cycle salt fog ageing test, alternate sheds silicone
rubber polymer insulator showed better contamination performance
than straight sheds silicone rubber polymer insulator. Severe surface
ageing was observed on the straight sheds insulator. The objective of
this work is to elucidate that electric field distribution along straight
sheds insulator higher than alternate shed insulator in salt fog ageing
test. Finite element method (FEM) is adopted for this work. The
simulation results confirmed the experimental data, as well.
Abstract: In this paper, the effect of bolt clamping force on the fatigue behavior of bolted single lap joints of aluminum alloy 2024- T3 have been studied using numerical finite element method. To do so, a three dimensional model according to the bolted single lap joint has been created and numerical analysis has been carried out using finite element based package. Then the stress distribution and also the slip amplitudes have been calculated in the critical regions and the outcome have been compared with the available experimental fatigue tests results. The numerical results show that in low applied clamping force, the fatigue failure of the specimens occur around the stress concentration location (the bolted hole edge) due to the tensile stresses and thus fatigue crack propagation, but with increase of the clamping force, the fatigue life increases and the cracks nucleate and propagate far from the hole edge because of fretting fatigue. In other words, with the further increase of clamping force value of the joint, the fatigue life reduces due to occurrence of the fretting fatigue in the critical location where the slip amplitude is within its critical occurs earlier.
Abstract: A biophysically based multilayer continuum model of the facial soft tissue composite has been developed for simulating wrinkle formation. The deformed state of the soft tissue block was determined by solving large deformation mechanics equations using the Galerkin finite element method. The proposed soft tissue model is composed of four layers with distinct mechanical properties. These include stratum corneum, epidermal-dermal layer (living epidermis and dermis), subcutaneous tissue and the underlying muscle. All the layers were treated as non-linear, isotropic Mooney Rivlin materials. Contraction of muscle fibres was approximated using a steady-state relationship between the fibre extension ratio, intracellular calcium concentration and active stress in the fibre direction. Several variations of the model parameters (stiffness and thickness of epidermal-dermal layer, thickness of subcutaneous tissue layer) have been considered.
Abstract: The paper deals with determination of electromagnetic
and temperature field distribution of induction heating system used
for pipe brazing. The problem is considered as coupled – time
harmonic electromagnetic and transient thermal field. It has been
solved using finite element method. The detailed maps of
electromagnetic and thermal field distribution have been obtained.
The good understanding of the processes in the considered system
ensures possibilities for control, management and increasing the
efficiency of the welding process.
Abstract: In this study, aeroelastic response and performance
analyses have been conducted for a 5MW-Class composite wind
turbine blade model. Advanced coupled numerical method based on
computational fluid dynamics (CFD) and computational flexible
multi-body dynamics (CFMBD) has been developed in order to
investigate aeroelastic responses and performance characteristics of
the rotating composite blade. Reynolds-Averaged Navier-Stokes
(RANS) equations with k-ω SST turbulence model were solved for
unsteady flow problems on the rotating turbine blade model. Also,
structural analyses considering rotating effect have been conducted
using the general nonlinear finite element method. A fully implicit
time marching scheme based on the Newmark direct integration
method is applied to solve the coupled aeroelastic governing equations
of the 3D turbine blade for fluid-structure interaction (FSI) problems.
Detailed dynamic responses and instantaneous velocity contour on the
blade surfaces which considering flow-separation effects were
presented to show the multi-physical phenomenon of the huge rotating
wind- turbine blade model.
Abstract: The transient thermoelastic response of thick hollow cylinder made of functionally graded material under thermal loading is studied. The generalized coupled thermoelasticity based on the Green-Lindsay model is used. The thermal and mechanical properties of the functionally graded material are assumed to be varied in the radial direction according to a power law variation as a function of the volume fractions of the constituents. The thermal and elastic governing equations are solved by using Galerkin finite element method. All the finite element calculations were done by using commercial finite element program FlexPDE. The transient temperature, radial displacement, and thermal stresses distribution through the radial direction of the cylinder are plotted.
Abstract: This study aimed to present the mechanical
performance evaluation of the dynamic hip screw (DHS) for
trochanteric fracture by means of finite element method. The
analyses were performed based on stainless steel and titanium
implant material definitions at various stages of bone healing and
including implant removal. The assessment of the mechanical
performance used two parameters, von Mises stress to evaluate the
strength of bone and implant and elastic strain to evaluate fracture
stability. The results show several critical aspects of dynamic hip
screw for trochanteric fracture stabilization. In the initial stage of
bone healing process, partial weight bearing should be applied to
avoid the implant failure. In the late stage of bone healing, stainless
steel implant should be removed.
Abstract: The mechanism behind the electromigration and
thermomigration failure in flip-chip solder joints with Cu-pillar bumps
was investigated in this paper through using finite element method.
Hot spot and the current crowding occurrs in the upper corner of
copper column instead of solders of the common solder ball. The
simulation results show that the change in thermal gradient is
noticeable, which might greatly affect the reliability of solder joints
with Cu-pillar bumps under current stressing. When the average
applied current density is increased from 1×104 A/cm2 to 3×104 A/cm2
in solders, the thermal gradient would increase from 74 K/cm to 901
K/cm at an ambient temperature of 25°C. The force from thermal
gradient of 901 K/cm can nearly induce thermomigration by itself.
With the increase in applied current, the thermal gradient is growing. It
is proposed that thermomigration likely causes a serious reliability
issue for Cu column based interconnects.
Abstract: In this study, stress distributions on dental implants
made of functionally graded biomaterials (FGBM) are investigated
numerically. The implant body is considered to be subjected to axial
compression loads. Numerical problem is assumed to be 2D, and
ANSYS commercial software is used for the analysis. The cross
section of the implant thread varies as varying the height (H) and the
width (t) of the thread. According to thread dimensions of implant
and material properties of FGBM, equivalent stress distribution on
the implant is determined and presented with contour plots along
with the maximum equivalent stress values. As a result, with
increasing material gradient parameter (n), the equivalent stress
decreases, but the minimum stress distribution increases. Maximum
stress values decrease with decreasing implant radius (r). Maximum
von Mises stresses increases with decreasing H when t is constant.
On the other hand, the stress values are not affected by variation of t
in the case of H = constant.
Abstract: One of Effective parameters on the performance of linear induction motors is number of poles which must be selected and optimized to increase power efficiency and motor performance significantly. In this paper a double-sided linear induction motor with different poles number by using MAXWELL3D software is designed and with finite element method is analyzed electromagnetically. Then for dynamic simulation, linear motor by using MATLAB software is simulated. The results show that by adding poles number, system time response is increased and motor after more time reaches to steady state. Also propulsion force of motor is increased.
Abstract: At present, the tendency to implement the conditionbased
maintenance (CBM), which allows the optimization of the
expenses for equipment monitoring, is more and more evident; also,
the transformer substations with remote monitoring are increasingly
used. This paper reviews all the advantages of the on-line monitoring
and presents an equipment for on-line monitoring of bushings, which
is the own contribution of specialists who are the authors of this
paper. The paper presents a study of the temperature field, using the
finite element method. For carrying out this study, the 3D modelling
of the above mentioned bushing was performed. The analysis study is
done taking into account the extreme thermal stresses, focusing at the
level of the first cooling wing section of the ceramic insulator. This
fact enables to justify the tanδ variation in time, depending on the
transformer loading and the environmental conditions. With a view
to reducing the variation of dielectric losses in bushing insulation, the
use of ferrofuids instead of mineral oils is proposed.
Abstract: Stress analysis of functionally graded composite plates
composed of ceramic, functionally graded material and metal layers is
investigated using 3-D finite element method. In FGM layer, material
properties are assumed to be varied continuously in the thickness
direction according to a simple power law distribution in terms of the
volume fraction of a ceramic and metal. The 3-D finite element model
is adopted by using an 18-node solid element to analyze more
accurately the variation of material properties in the thickness
direction. Numerical results are compared for three types of materials.
In the analysis, the tensile and the compressive stresses are
summarized for various FGM thickness ratios, volume fraction
distributions, geometric parameters and mechanical loads.
Abstract: The scalar wave equation for a potential in a curved space time, i.e., the Laplace-Beltrami equation has been studied in this work. An action principle is used to derive a finite element algorithm for determining the modes of propagation inside a waveguide of arbitrary shape. Generalizing this idea, the Maxwell theory in a curved space time determines a set of linear partial differential equations for the four electromagnetic potentials given by the metric of space-time. Similar to the Einstein-s formulation of the field equations of gravitation, these equations are also derived from an action principle. In this paper, the expressions for the action functional of the electromagnetic field have been derived in the presence of gravitational field.
Abstract: A stiffened laminated composite panel (1 m length ×
0.5m width) was optimized for minimum weight and deflection under
several constraints using genetic algorithm. Here, a significant study
on the performance of a penalty function with two kinds of static and
dynamic penalty factors was conducted. The results have shown that
linear dynamic penalty factors are more effective than the static ones.
Also, a specially combined linear-exponential function has shown to
perform more effective than the previously mentioned penalty
functions. This was then resulted in the less sensitivity of the GA to
the amount of penalty factor.
Abstract: The development and extension of large cities induced
a need for shallow tunnel in soft ground of building areas. Estimation
of ground settlement caused by the tunnel excavation is important
engineering point. In this paper, prediction of surface subsidence
caused by tunneling in one section of seventh line of Tehran subway
is considered. On the basis of studied geotechnical conditions of the
region, tunnel with the length of 26.9km has been excavated applying
a mechanized method using an EPB-TBM with a diameter of 9.14m.
In this regard, settlement is estimated utilizing both analytical and
numerical finite element method. The numerical method shows that
the value of settlement in this section is 5cm. Besides, the analytical
consequences (Bobet and Loganathan-Polous) are 5.29 and 12.36cm,
respectively. According to results of this study, due tosaturation of
this section, there are good agreement between Bobet and numerical
methods. Therefore, tunneling processes in this section needs a
special consolidation measurement and support system before the
passage of tunnel boring machine.
Abstract: The effect of thermally induced stress on the modal
properties of highly elliptical core optical fibers is studied in this
work using a finite element method. The stress analysis is carried out
and anisotropic refractive index change is calculated using both the
conventional plane strain approximation and the generalized plane
strain approach. After considering the stress optical effect, the modal
analysis of the fiber is performed to obtain the solutions of
fundamental and higher order modes. The modal effective index,
modal birefringence, group effective index, group birefringence, and
dispersion of different modes of the fiber are presented. For
propagation properties, it can be seen that the results depend much on
the approach of stress analysis.
Abstract: Following harvest, fresh produce needs to be cooled
immediately in a room where the air temperature and the relative air
humidity are controlled to maintain the produce quality. In this paper,
an experimental study for forced air cooling of fresh produce
(cauliflower) is performed using a pilot developed within our
laboratory. Furthermore, a numerical simulation of spherical
produces, taking into account the aerodynamic aspect and also the
heat transfer in the produce and in the air, was carried out using a
finite element method. At the end of this communication,
experimental results are presented and compared with the simulation.