Abstract: Explosive welding is a process which uses explosive
detonation to move the flyer plate material into the base material to
produce a solid state joint. Experimental tests have been carried out
by other researchers; have been considered to explosively welded
aluminium 7039 and steel 4340 tubes in one step. The tests have been
done using various stand-off distances and explosive ratios. Various
interface geometries have been obtained from these experiments. In
this paper, all the experiments carried out were simulated using the
finite element method. The flyer plate and collision velocities
obtained from the analysis were validated by the pin-measurement
experiments. The numerical results showed that very high localized
plastic deformation produced at the bond interface. The
Ls_dyna_971 FEM has been used for all simulation process.
Abstract: Reinforced concrete stair slabs with mid landings i.e.
Dog-legged shaped are conventionally designed as per specifications
of standard codes of practices which guide about the effective span
according to the varying support conditions. Presently, the behavior
of such slabs has been investigated using Finite Element method. A
single flight stair slab with landings on both sides and supported at
ends on wall, and a multi flight stair slab with landings and six
different support arrangements have been analyzed. The results
obtained for stresses, strains and deflections are used to describe the
behavior of such stair slabs, including locations of critical moments
and deflections. Values of critical moments obtained by F.E. analysis
have also have been compared with that obtained from conventional
analysis. Analytical results show that the moments are also critical
near the kinks i.e. junction of mid-landing and inclined waist slab.
This change in the behavior of dog-legged stair slab may be due to
continuity of the material in transverse direction in two landings
adjoining the waist slab, hence additional stiffness achieved. This
change in the behavior is generally not taken care of in conventional
method of design.
Abstract: This paper deals with behavior and capacity of
punching shear force for flat slabs produced from steel fiber
reinforced self compacting concrete (SFRSCC) by application
nonlinear finite element method. Nonlinear finite element analysis on
nine slab specimens was achieved by using ANSYS software. A
general description of the finite element method, theoretical modeling
of concrete and reinforcement are presented. The nonlinear finite
element analysis program ANSYS is utilized owing to its capabilities
to predict either the response of reinforced concrete slabs in the post
elastic range or the ultimate strength of a flat slabs produced from
steel fiber reinforced self compacting concrete (SFRSCC). In order to
verify the analytical model used in this research using test results of
the experimental data, the finite element analysis were performed
then a parametric study of the effect ratio of flexural reinforcement,
ratio of the upper reinforcement, and volume fraction of steel fibers
were investigated. A comparison between the experimental results
and those predicted by the existing models are presented. Results and
conclusions may be useful for designers, have been raised, and
represented.
Abstract: This study is to investigate the electroencephalogram (EEG) differences generated from a normal and Alzheimer-s disease (AD) sources. We also investigate the effects of brain tissue distortions due to AD on EEG. We develop a realistic head model from T1 weighted magnetic resonance imaging (MRI) using finite element method (FEM) for normal source (somatosensory cortex (SC) in parietal lobe) and AD sources (right amygdala (RA) and left amygdala (LA) in medial temporal lobe). Then, we compare the AD sourced EEGs to the SC sourced EEG for studying the nature of potential changes due to sources and 5% to 20% brain tissue distortions. We find an average of 0.15 magnification errors produced by AD sourced EEGs. Different brain tissue distortion models also generate the maximum 0.07 magnification. EEGs obtained from AD sources and different brain tissue distortion levels vary scalp potentials from normal source, and the electrodes residing in parietal and temporal lobes are more sensitive than other electrodes for AD sourced EEG.
Abstract: Multilobe bearings are found to be more stable than circular bearings. A three lobe bearing also possesses good stability characteristics. Sometimes the line of action of the load does not pass through the axis of a bearing and is shifted on either side by a few degrees. Load orientation is one of the factors that affect the stability of a three lobe bearing. The effect of load orientation on the stability of a three-lobe has been discussed in this paper. The results show that stability of a three-lobe bearing supporting either rigid or flexible rotor is increased for the positive values of load orientation i.e. when the load line is shifted in the opposite direction of rotation.
Abstract: Evaluation of contact pressure, surface and
subsurface contact stresses are essential to know the functional
response of surface coatings and the contact behavior mainly depends
on surface roughness, material property, thickness of layer and the
manner of loading. Contact parameter evaluation of real rough
surface contacts mostly relies on statistical single asperity contact
approaches. In this work, a three dimensional layered solid rough
surface in contact with a rigid flat is modeled and analyzed using
finite element method. The rough surface of layered solid is
generated by FFT approach. The generated rough surface is exported
to a finite element method based ANSYS package through which the
bottom up solid modeling is employed to create a deformable solid
model with a layered solid rough surface on top. The discretization
and contact analysis are carried by using the same ANSYS package.
The elastic, elastoplastic and plastic deformations are continuous in
the present finite element method unlike many other contact models.
The Young-s modulus to yield strength ratio of layer is varied in the
present work to observe the contact parameters effect while keeping
the surface roughness and substrate material properties as constant.
The contacting asperities attain elastic, elastoplastic and plastic states
with their continuity and asperity interaction phenomena is inherently
included. The resultant contact parameters show that neighboring
asperity interaction and the Young-s modulus to yield strength ratio
of layer influence the bulk deformation consequently affect the
interface strength.
Abstract: In this paper, mesh-free element free Galerkin (EFG) method is extended to solve two-dimensional potential flow problems. Two ideal fluid flow problems (i.e. flow over a rigid cylinder and flow over a sphere) have been formulated using variational approach. Penalty and Lagrange multiplier techniques have been utilized for the enforcement of essential boundary conditions. Four point Gauss quadrature have been used for the integration on two-dimensional domain (Ω) and nodal integration scheme has been used to enforce the essential boundary conditions on the edges (┌). The results obtained by EFG method are compared with those obtained by finite element method. The effects of scaling and penalty parameters on EFG results have also been discussed in detail.
Abstract: Nanomaterials have attracted considerable attention
during the last two decades, due to their unusual electrical, mechanical
and other physical properties as compared with their bulky
counterparts. The mechanical properties of nanostructured materials
show strong size dependency, which has been explained within the
framework of continuum mechanics by including the effects of surface
stress. The size-dependent deformations of two-dimensional
nanosized structures with surface effects are investigated in the paper
by the finite element method. Truss element is used to evaluate the
contribution of surface stress to the total potential energy and the
Gurtin and Murdoch surface stress model is implemented with
ANSYS through its user programmable features. The proposed
approach is used to investigate size-dependent stress concentration
around a nanosized circular hole and the size-dependent effective
moduli of nanoporous materials. Numerical results are compared with
available analytical results to validate the proposed modeling
approach.
Abstract: Minimally invasive surgery (MIS) is now being widely used as a preferred choice for various types of operations. The need to detect various tactile properties, justifies the key role of tactile sensing that is currently missing in MIS. In this regard, Laparoscopy is one of the methods of minimally invasive surgery that can be used in kidney stone removal surgeries. At this moment, determination of the exact location of stone during laparoscopy is one of the limitations of this method that no scientific solution has been found for so far. Artificial tactile sensing is a new method for obtaining the characteristics of a hard object embedded in a soft tissue. Artificial palpation is an important application of artificial tactile sensing that can be used in different types of surgeries. In this study, a new method for determining the exact location of stone during laparoscopy is presented. In the present study, the effects of stone existence on the surface of kidney were investigated using conceptual 3D model of kidney containing a simulated stone. Having imitated palpation and modeled it conceptually, indications of stone existence that appear on the surface of kidney were determined. A number of different cases were created and solved by the software and using stress distribution contours and stress graphs, it is illustrated that the created stress patterns on the surface of kidney show not only the existence of stone inside, but also its exact location. So three-dimensional analysis leads to a novel method of predicting the exact location of stone and can be directly applied to the incorporation of tactile sensing in artificial palpation, helping surgeons in non-invasive procedures.
Abstract: The distributions of stresses and deflection in
rectangular isotropic and orthotropic plates with central
circular hole under transverse static loading have been studied
using finite element method. The aim of author is to analyze
the effect of D/A ratio (where D is hole diameter and A is plate
width) upon stress concentration factor (SCF) and deflection
in isotropic and orthotropic plates under transverse static
loading. The D/A ratio is varied from 0.01 to 0.9. The analysis
is done for plates of isotropic and two different orthotropic
materials. The results are obtained for three different boundary
conditions. The variations of SCF and deflection with respect
to D/A ratio are presented in graphical form and discussed.
The finite element formulation is carried out in the analysis
section of the ANSYS package.