Abstract: The problem of N cracks interaction in an isotropic
elastic solid is decomposed into a subproblem of a homogeneous solid
without crack and N subproblems with each having a single crack
subjected to unknown tractions on the two crack faces. The unknown
tractions, namely pseudo tractions on each crack are expanded into
polynomials with unknown coefficients, which have to be determined
by the consistency condition, i.e. by the equivalence of the original
multiple cracks interaction problem and the superposition of the N+1
subproblems. In this paper, Kachanov-s approach of average tractions
is extended into the method of moments to approximately impose the
consistence condition. Hence Kachanov-s method can be viewed as
the zero-order method of moments. Numerical results of the stress
intensity factors are presented for interactions of two collinear cracks,
three collinear cracks, two parallel cracks, and three parallel cracks.
As the order of moment increases, the accuracy of the method of
moments improves.
Abstract: Researches on the general rules of temperature field
changing and their effects on the bridge in construction are necessary.
This paper investigated the rules of temperature field changing and its
effects on bridge using onsite measurement and computational
analysis. Guanyinsha Bridge was used as a case study in this research.
The temperature field was simulated in analyses. The effects of certain
boundary conditions such as sun radiance, wind speed, and model
parameters such as heat factor and specific heat on temperature field
are investigated. Recommended values for these parameters are
proposed. The simulated temperature field matches the measured
observations with high accuracy. At the same time, the stresses and
deflections of the bridge computed with the simulated temperature
field matches measured values too. As a conclusion, the temperature
effect analysis of reinforced concrete box girder can be conducted
directly based on the reliable weather data of the concerned area.
Abstract: When the characteristic length of an elastic solid is
down to the nanometer level, its deformation behavior becomes size
dependent. Surface energy /surface stress have recently been applied
to explain such dependency. In this paper, the effect of
strain-independent surface stress on the deformation of an isotropic
elastic solid containing a nanosized elliptical hole is studied by the
finite element method. Two loading cases are considered, in the first
case, hoop stress along the rim of the elliptical hole induced by pure
surface stress is studied, in the second case, hoop stress around the
elliptical opening under combined remote tension and surface stress is
investigated. It has been shown that positive surface stress induces
compressive hoop stress along the hole, and negative surface stress has
opposite effect, maximum hoop stress occurs near the major semi-axes
of the ellipse. Under combined loading of remote tension and surface
stress, stress concentration around the hole can be either intensified or
weakened depending on the sign of the surface stress.
Abstract: The cable tower of Liede Bridge is a double-column curved-lever arched-beam portal framed structure. Being novel and unique in structure, its cable tower differs in complexity from traditional ones. This paper analyzes the ultimate load capacity of cable tower by adopting the finite element calculations and model tests which indicate that constitutive relations applied here give a better simulation of actual failure process of prestressed reinforced concrete. In vertical load, horizontal load and overloading tests, the stepped loading of the tower model is of linear relationship, and the test data has good repeatability. All suggests that the cable tower has good bearing capacity, rational design and high emergency capacity.
Abstract: The launching nose plays an important role in the
incremental launching construction. The parameters of the launching
nose essentially affect the internal forces of the girder during the
construction. The appropriate parameters can decrease the internal
forces in the girder and save the material and reduce the cost. The
simplified structural model, which is made with displacement method
according to the characteristic of incremental launching construction
and the variation rule of the internal forces, calculates and analyzes the
effect of the length, the rigidity and weight of launch nose on the
internal forces of girder during the incremental launching
construction. The method, which can calculate the launching nose
parameters for the optimum incremental launching construction, is
achieved. This method is simple, reliable and easy for practical use.
Abstract: The nearly 21-year-old Jiujiang Bridge, which is suffering from uneven line shape, constant great downwarping of the main beam and cracking of the box girder, needs reinforcement and cable adjustment. It has undergone cable adjustment for twice with incomplete data. Therefore, the initial internal force state of the Jiujiang Bridge is identified as the key for the cable adjustment project. Based on parameter identification by means of static force test data, this paper suggests determining the initial internal force state of the cable-stayed bridge according to the cable force-displacement relationship parameter identification method. That is, upon measuring the displacement and the change in cable forces for twice, one can identify the parameters concerned by means of optimization. This method is applied to the cable adjustment, replacement and reinforcement project for the Jiujiang Bridge as a guidance for the cable adjustment and reinforcement project of the bridge.
Abstract: Nanomaterials have attracted considerable attention
during the last two decades, due to their unusual electrical, mechanical
and other physical properties as compared with their bulky
counterparts. The mechanical properties of nanostructured materials
show strong size dependency, which has been explained within the
framework of continuum mechanics by including the effects of surface
stress. The size-dependent deformations of two-dimensional
nanosized structures with surface effects are investigated in the paper
by the finite element method. Truss element is used to evaluate the
contribution of surface stress to the total potential energy and the
Gurtin and Murdoch surface stress model is implemented with
ANSYS through its user programmable features. The proposed
approach is used to investigate size-dependent stress concentration
around a nanosized circular hole and the size-dependent effective
moduli of nanoporous materials. Numerical results are compared with
available analytical results to validate the proposed modeling
approach.