Abstract: To understand the factors which affect impact damage on composite structures, particularly the effects of impact position and ribs. In this paper, a finite element model (FEM) of low-velocity impact damage on the composite structure was established via the nonlinear finite element method, combined with the user-defined materials subroutine (VUMAT) of the ABAQUS software. The structural elements chosen for the investigation comprised a series of stiffened composite panels, representative of real aircraft structure. By impacting the panels at different positions relative to the ribs, the effect of relative position of ribs was found out. Then the simulation results and the experiments data were compared. Finally, the factors which affect impact damage on the structures were discussed. The paper was helpful for the design of stiffened composite structures.
Abstract: To enhance installation security, a LNG storage in Rudong of Jiangsu province was adopted as a practical work, and it was analyzed by nonlinear finite element method to research overall and local stability performance, as well as the stress and deformation under the action of wind load and self-weight. Results indicate that deformation is tiny when steel mesh maintains as an overall ring, and stress caused by vertical bending moment and tension of bottom tie wire are also in the safe range. However, axial forces of lap reinforcement in adjacent steel mesh exceed the ultimate bearing capacity of tie wire. Hence, tie wires are ruptured; single mesh loses lateral connection and turns into monolithic status as the destruction of overall structure. Further more, monolithic steel mesh is led to collapse by the damage of bottom connection. So, in order to prevent connection failure and enhance installation security, the overlapping parts of steel mesh should be taken more reliable measures.
Abstract: The cable tower of Liede Bridge is a double-column curved-lever arched-beam portal framed structure. Being novel and unique in structure, its cable tower differs in complexity from traditional ones. This paper analyzes the ultimate load capacity of cable tower by adopting the finite element calculations and model tests which indicate that constitutive relations applied here give a better simulation of actual failure process of prestressed reinforced concrete. In vertical load, horizontal load and overloading tests, the stepped loading of the tower model is of linear relationship, and the test data has good repeatability. All suggests that the cable tower has good bearing capacity, rational design and high emergency capacity.
Abstract: In this study, aeroelastic response and performance
analyses have been conducted for a 5MW-Class composite wind
turbine blade model. Advanced coupled numerical method based on
computational fluid dynamics (CFD) and computational flexible
multi-body dynamics (CFMBD) has been developed in order to
investigate aeroelastic responses and performance characteristics of
the rotating composite blade. Reynolds-Averaged Navier-Stokes
(RANS) equations with k-ω SST turbulence model were solved for
unsteady flow problems on the rotating turbine blade model. Also,
structural analyses considering rotating effect have been conducted
using the general nonlinear finite element method. A fully implicit
time marching scheme based on the Newmark direct integration
method is applied to solve the coupled aeroelastic governing equations
of the 3D turbine blade for fluid-structure interaction (FSI) problems.
Detailed dynamic responses and instantaneous velocity contour on the
blade surfaces which considering flow-separation effects were
presented to show the multi-physical phenomenon of the huge rotating
wind- turbine blade model.
Abstract: Nonlinear finite element method and Serendipity eight
nodes element are used for determining of ground surface settlement
due to tunneling. Linear element with elastic behavior is used for
modeling of lining. Modified Generalized plasticity model with nonassociated
flow rule is applied for analysis of a tunnel in Sao Paulo –
Brazil. The tunnel had analyzed by Lades- model with 16 parameters.
In this work modified Generalized Plasticity is used with 10
parameters, also Mohr-Coulomb model is used to analysis the tunnel.
The results show good agreement with observed results of field data
by modified Generalized Plasticity model than other models. The
obtained result by Mohr-Coulomb model shows less settlement than
other model due to excavation.
Abstract: This paper deals with behavior and capacity of
punching shear force for flat slabs produced from steel fiber
reinforced self compacting concrete (SFRSCC) by application
nonlinear finite element method. Nonlinear finite element analysis on
nine slab specimens was achieved by using ANSYS software. A
general description of the finite element method, theoretical modeling
of concrete and reinforcement are presented. The nonlinear finite
element analysis program ANSYS is utilized owing to its capabilities
to predict either the response of reinforced concrete slabs in the post
elastic range or the ultimate strength of a flat slabs produced from
steel fiber reinforced self compacting concrete (SFRSCC). In order to
verify the analytical model used in this research using test results of
the experimental data, the finite element analysis were performed
then a parametric study of the effect ratio of flexural reinforcement,
ratio of the upper reinforcement, and volume fraction of steel fibers
were investigated. A comparison between the experimental results
and those predicted by the existing models are presented. Results and
conclusions may be useful for designers, have been raised, and
represented.
Abstract: Nonlinear finite element method with eight noded
isoparametric quadrilateral element is used for prediction of loaddeformation
behavior including bearing capacity of foundations.
Modified generalized plasticity model with non-associated flow rule
is applied for analysis of soil-footing system. Also Von Mises and
Tresca criterions are used for simulation of soil behavior. Modified
generalized plasticity model is able to simulate load-deformation
including softening behavior. Localization phenomena are considered
by different meshes. Localization phenomena have not been seen in
the examples. Predictions by modified generalized plasticity model
show good agreement with laboratory data and theoretical prediction
in comparison the other models.