Abstract: In this paper, we present a simple circuit for
Manchester decoding and without using any complicated or
programmable devices. This circuit can decode 90kbps of transmitted
encoded data; however, greater than this transmission rate can be
decoded if high speed devices were used. We also present a new
method for extracting the embedded clock from Manchester data in
order to use it for serial-to-parallel conversion. All of our
experimental measurements have been done using simulation.
Abstract: Speedups from mapping four real-life DSP
applications on an embedded system-on-chip that couples coarsegrained
reconfigurable logic with an instruction-set processor are
presented. The reconfigurable logic is realized by a 2-Dimensional
Array of Processing Elements. A design flow for improving
application-s performance is proposed. Critical software parts, called
kernels, are accelerated on the Coarse-Grained Reconfigurable
Array. The kernels are detected by profiling the source code. For
mapping the detected kernels on the reconfigurable logic a prioritybased
mapping algorithm has been developed. Two 4x4 array
architectures, which differ in their interconnection structure among
the Processing Elements, are considered. The experiments for eight
different instances of a generic system show that important overall
application speedups have been reported for the four applications.
The performance improvements range from 1.86 to 3.67, with an
average value of 2.53, compared with an all-software execution.
These speedups are quite close to the maximum theoretical speedups
imposed by Amdahl-s law.
Abstract: A steady two-dimensional magnetohydrodynamics
flow and heat transfer over a stretching vertical sheet influenced by
radiation and porosity is studied. The governing boundary layer
equations of partial differential equations are reduced to a system of
ordinary differential equations using similarity transformation. The
system is solved numerically by using a finite difference scheme
known as the Keller-box method for some values of parameters,
namely the radiation parameter N, magnetic parameter M, buoyancy
parameter l , Prandtl number Pr and permeability parameter K. The
effects of the parameters on the heat transfer characteristics are
analyzed and discussed. It is found that both the skin friction
coefficient and the local Nusselt number decrease as the magnetic
parameter M and permeability parameter K increase. Heat transfer
rate at the surface decreases as the radiation parameter increases.
Abstract: An innovative tri-axes micro-power receiver is
proposed. The tri-axes micro-power receiver consists of two sets 3-D
micro-solenoids and one set planar micro-coils in which iron core is
embedded. The three sets of micro-coils are designed to be orthogonal
to each other. Therefore, no matter which direction the flux is present
along, the magnetic energy can be harvested and transformed into
electric power. Not only dead space of receiving power is mostly
reduced, but also transformation efficiency of electromagnetic energy
to electric power can be efficiently raised. By employing commercial
software, Ansoft Maxwell, the preliminary simulation results verify
that the proposed micro-power receiver can efficiently pick up the
energy transmitted by magnetic power source.
As to the fabrication process, the isotropic etching technique is
employed to micro-machine the inverse-trapezoid fillister so that the
copper wire can be successfully electroplated. The adhesion between
micro-coils and fillister is much enhanced.
Abstract: Today-s manufacturing companies are facing multiple and dynamic customer-supplier-relationships embedded in nonhierarchical production networks. This complex environment leads to problems with delivery reliability and wasteful turbulences throughout the entire network. This paper describes an operational model based on a theoretical framework which improves delivery reliability of each individual customer-supplier-relationship within non-hierarchical production networks of the European machinery and equipment industry. By developing a non-centralized coordination mechanism based on determining the value of delivery reliability and derivation of an incentive system for suppliers the number of in time deliveries can be increased and thus the turbulences in the production network smoothened. Comparable to an electronic stock exchange the coordination mechanism will transform the manual and nontransparent process of determining penalties for delivery delays into an automated and transparent market mechanism creating delivery reliability.
Abstract: Social media has led to paradigm shifts in ways
people work and do business, interact and socialize, learn and obtain
knowledge. So much so that social media has established itself as an
important spatial extension of this nation-s historicity and challenges.
Regardless of the enabling reputation and recommendation features
through social networks embedded in the social media system, the
overflow of broadcasted and publicized media contents turns the
table around from engendering trust to doubting the trust system.
When the trust is at doubt, the effects include deactivation of
accounts and creation of multiple profiles, which lead to the overflow
of 'ghost' contents (i.e. “the abundance of abandoned ships"). In
most literature, the study of trust can be related to culture; hence the
difference between Western-s “openness" and Eastern-s “blue-chip"
concepts in networking and relationships. From a survey on issues
and challenges among Malaysian social media users, 'authenticity'
emerges as one of the main factors that causes and is caused by other
factors. The other issue that has surfaced is credibility either in terms
of message/content and source. Another is the quality of the
knowledge that is shared. This paper explores the terrains of this
critical space which in recent years has been dominated increasingly
by, arguably, social networks embedded in the social media system,
the overflow of broadcasted and publicized media content.
Abstract: With increasing utilization of the wireless devices in
different fields such as medical devices and industrial fields, the
paper presents a method for simplify the Bluetooth packets with
throughput enhancing. The paper studies a vital issue in wireless
communications, which is the throughput of data over wireless
networks. In fact, the Bluetooth and ZigBee are a Wireless Personal
Area Network (WPAN). With taking these two systems competition
consideration, the paper proposes different schemes for improve the
throughput of Bluetooth network over a reliable channel. The
proposition depends on the Channel Quality Driven Data Rate
(CQDDR) rules, which determines the suitable packet in the
transmission process according to the channel conditions. The
proposed packet is studied over additive White Gaussian Noise
(AWGN) and fading channels. The Experimental results reveal the
capability of extension of the PL length by 8, 16, 24 bytes for classic
and EDR packets, respectively. Also, the proposed method is suitable
for the low throughput Bluetooth.
Abstract: Authentication of multimedia contents has gained much attention in recent times. In this paper, we propose a secure semi-fragile watermarking, with a choice of two watermarks to be embedded. This technique operates in integer wavelet domain and makes use of semi fragile watermarks for achieving better robustness. A self-recovering algorithm is employed, that hides the image digest into some Wavelet subbands to detect possible malevolent object manipulation undergone by the image (object replacing and/or deletion). The Semi-fragility makes the scheme tolerant for JPEG lossy compression as low as quality of 70%, and locate the tempered area accurately. In addition, the system ensures more security because the embedded watermarks are protected with private keys. The computational complexity is reduced using parameterized integer wavelet transform. Experimental results show that the proposed scheme guarantees the safety of watermark, image recovery and location of the tempered area accurately.
Abstract: In order to protect original data, watermarking is first consideration direction for digital information copyright. In addition, to achieve high quality image, the algorithm maybe can not run on embedded system because the computation is very complexity. However, almost nowadays algorithms need to build on consumer production because integrator circuit has a huge progress and cheap price. In this paper, we propose a novel algorithm which efficient inserts watermarking on digital image and very easy to implement on digital signal processor. In further, we select a general and cheap digital signal processor which is made by analog device company to fit consumer application. The experimental results show that the image quality by watermarking insertion can achieve 46 dB can be accepted in human vision and can real-time execute on digital signal processor.
Abstract: Real options theory suggests that managerial flexibility embedded within irreversible investments can account for a significant value in project valuation. Although the argument has become the dominant focus of capital investment theory over decades, yet recent survey literature in capital budgeting indicates that corporate practitioners still do not explicitly apply real options in investment decisions. In this paper, we explore how real options decision criteria can be transformed into equivalent capital budgeting criteria under the consideration of uncertainty, assuming that underlying stochastic process follows a geometric Brownian motion (GBM), a mixed diffusion-jump (MX), or a mean-reverting process (MR). These equivalent valuation techniques can be readily decomposed into conventional investment rules and “option impacts", the latter of which describe the impacts on optimal investment rules with the option value considered. Based on numerical analysis and Monte Carlo simulation, three major findings are derived. First, it is shown that real options could be successfully integrated into the mindset of conventional capital budgeting. Second, the inclusion of option impacts tends to delay investment. It is indicated that the delay effect is the most significant under a GBM process and the least significant under a MR process. Third, it is optimal to adopt the new capital budgeting criteria in investment decision-making and adopting a suboptimal investment rule without considering real options could lead to a substantial loss in value.
Abstract: In this paper, a new reversible watermarking method is presented that reduces the size of a stereoscopic image sequence while keeping its content visible. The proposed technique embeds the residuals of the right frames to the corresponding frames of the left sequence, halving the total capacity. The residual frames may result in after a disparity compensated procedure between the two video streams or by a joint motion and disparity compensation. The residuals are usually lossy compressed before embedding because of the limited embedding capacity of the left frames. The watermarked frames are visible at a high quality and at any instant the stereoscopic video may be recovered by an inverse process. In fact, the left frames may be exactly recovered whereas the right ones are slightly distorted as the residuals are not embedded intact. The employed embedding method reorders the left frame into an array of consecutive pixel pairs and embeds a number of bits according to their intensity difference. In this way, it hides a number of bits in intensity smooth areas and most of the data in textured areas where resulting distortions are less visible. The experimental evaluation demonstrates that the proposed scheme is quite effective.
Abstract: Commercial nanocomposite food packaging type nano-silver containers were characterised using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The presence of nanoparticles consistent with the incorporation of 1% nano-silver (Ag) and 0.1% titanium dioxide (TiO2) nanoparticle into polymeric materials formed into food containers was confirmed. Both nanomaterials used in this type of packaging appear to be embedded in a layered configuration within the bulk polymer. The dimensions of the incorporated nanoparticles were investigated using X-ray diffraction (XRD) and determined by calculation using the Scherrer Formula; these were consistent with Ag and TiO2 nanoparticles in the size range 20-70nm both were spherical shape nanoparticles. Antimicrobial assessment of the nanocomposite container has also been performed and the results confirm the antimicrobial activity of Ag and TiO2 nanoparticles in food packaging containers. Migration assessments were performed in a wide range of food matrices to determine the migration of nanoparticles from the packages. The analysis was based upon the relevant European safety Directives and involved the application of inductively coupled plasma mass spectrometry (ICP-MS) to identify the range of migration risk. The data pertain to insignificance levels of migration of Ag and TiO2 nanoparticles into the selected food matrices.
Abstract: The problem of natural convection about a cone embedded in a porous medium at local Rayleigh numbers based on the boundary layer approximation and the Darcy-s law have been studied before. Similarity solutions for a full cone with the prescribed wall temperature or surface heat flux boundary conditions which is the power function of distance from the vertex of the inverted cone give us a third-order nonlinear differential equation. In this paper, an approximate method for solving higher-order ordinary differential equations is proposed. The approach is based on a rational Chebyshev Tau (RCT) method. The operational matrices of the derivative and product of rational Chebyshev (RC) functions are presented. These matrices together with the Tau method are utilized to reduce the solution of the higher-order ordinary differential equations to the solution of a system of algebraic equations. We also present the comparison of this work with others and show that the present method is applicable.
Abstract: Wind power is among the most actively developing distributed generation (DG) technology. Majority of the wind power based DG technologies employ wind turbine induction generators (WTIG) instead of synchronous generators, for the technical advantages like: reduced size, increased robustness, lower cost, and increased electromechanical damping. However, dynamic changes of wind speed make the amount of active/reactive power injected/drawn to a WTIG embedded distribution network highly variable. This paper analyzes the effect of wind speed changes on the active and reactive power penetration to the wind energy embedded distribution network. Four types of wind speed changes namely; constant, linear change, gust change and random change of wind speed are considered in the analysis. The study is carried out by three-phase, non-linear, dynamic simulation of distribution system component models. Results obtained from the investigation are presented and discussed.
Abstract: Considering toxicity of heavy metals and their
accumulation in domestic wastes, immobilization of lead and
cadmium is envisaged inside glass-ceramics. We particularly
focused this work on calcium-rich phases embedded in a
glassy matrix.
Glass-ceramics were synthesized from glasses doped with
12 wt% and 16 wt% of PbO or CdO. They were observed and
analyzed by Electron MicroProbe Analysis (EMPA) and
Analytical Scanning Electron Microscopy (ASEM). Structural
characterization of the samples was performed by powder XRay
Diffraction.
Diopside crystals of CaMgSi2O6 composition are shown to
incorporate significant amounts of cadmium (up to 9 wt% of
CdO). Two new crystalline phases are observed with very
high Cd or Pb contents: about 40 wt% CdO for the cadmiumrich
phase and near 60 wt% PbO for the lead-rich phase. We
present complete chemical and structural characterization of
these phases. They represent a promising way for the
immobilization of toxic elements like Cd or Pb since glass
ceramics are known to propose a “double barrier" protection
(metal-rich crystals embedded in a glass matrix) against metal
release in the environment.
Abstract: The importance of machining process in today-s
industry requires the establishment of more practical approaches to
clearly represent the intimate and severe contact on the tool-chipworkpiece
interfaces. Mathematical models are developed using the
measured force signals to relate each of the tool-chip friction
components on the rake face to the operating cutting parameters in
rough turning operation using multilayers coated carbide inserts.
Nonlinear modeling proved to have high capability to detect the
nonlinear functional variability embedded in the experimental data.
While feedrate is found to be the most influential parameter on the
friction coefficient and its related force components, both cutting
speed and depth of cut are found to have slight influence. Greater
deformed chip thickness is found to lower the value of friction
coefficient as the sliding length on the tool-chip interface is reduced.
Abstract: The importance of low power consumption is widely
acknowledged due to the increasing use of portable devices, which
require minimizing the consumption of energy. Energy dissipation is
heavily dependent on the software used in the system. Applying
design patterns in object-oriented designs is a common practice
nowadays. In this paper we analyze six design patterns and explore
the effect of them on energy consumption and performance.
Abstract: We study in this paper the effect of the scene
changing on image sequences coding system using Embedded
Zerotree Wavelet (EZW). The scene changing considered here is the
full motion which may occurs. A special image sequence is generated
where the scene changing occurs randomly. Two scenarios are
considered: In the first scenario, the system must provide the
reconstruction quality as best as possible by the management of the
bit rate (BR) while the scene changing occurs. In the second scenario,
the system must keep the bit rate as constant as possible by the
management of the reconstruction quality. The first scenario may be
motivated by the availability of a large band pass transmission
channel where an increase of the bit rate may be possible to keep the
reconstruction quality up to a given threshold. The second scenario
may be concerned by the narrow band pass transmission channel
where an increase of the bit rate is not possible. In this last case,
applications for which the reconstruction quality is not a constraint
may be considered. The simulations are performed with five scales
wavelet decomposition using the 9/7-tap filter bank biorthogonal
wavelet. The entropy coding is performed using a specific defined
binary code book and EZW algorithm. Experimental results are
presented and compared to LEAD H263 EVAL. It is shown that if
the reconstruction quality is the constraint, the system increases the
bit rate to obtain the required quality. In the case where the bit rate
must be constant, the system is unable to provide the required quality
if the scene change occurs; however, the system is able to improve
the quality while the scene changing disappears.
Abstract: This paper demonstrates an effort of a serviceoriented
engineering department in improving the sharing and
transfer of knowledge. Although the department consist of only six
employees, but it provides services in various chemical application in
an oil and gas business. The services provided span across Asia
Pacific region mainly Indonesia, Myanmar, Vietnam, Brunei,
Thailand and Singapore. Currently there are no effective tools or
integrated systems that support the sharing or transfer and
maintenance of knowledge so the department has considered
preserving this valuable knowledge by developing a Knowledge
Management System (KMS). This paper presents the development of
a KMS to support the sharing of knowledge in a service-oriented
engineering department of an oil and gas company. The embedded
features in the KMS like blog and forum will encourage iterative
process of knowledge sharing among the employees in the
department. The information and knowledge being shared, discussed
and communicated will be then achieved for future re-use. The re-use
of the knowledge allows the department to reduce redundant efforts
in providing consistent, up-to-date and cost effective of the best
solution to the its clients.
Abstract: A composite made of plasma functionalized multiwall
carbon nanotubes (MWNTs) coated with SnO2 was synthesized by
sonochemical precipitation method. Thick layer of this
nanocomposite material was used as ethanol sensor at low
temperatures. The composite sensitivity for ethanol has increased by
a factor of 2 at room temperature and by a factor of 13 at 250°C in
comparison to that of pure SnO2. SEM image of nanocomposite
material showed MWNTs were embedded in SnO2 matrix and also a
higher surface area was observed in the presence of functionalized
MWNTs. Greatly improved sensitivity of the composite material to
ethanol can be attributed to new gas accessing passes through
MWNTs and higher specific surface area.