Abstract: The causality between energy consumption and
economic growth has been an important issue in the economic
literature. This paper studies the causal relationship between
electricity consumption and economic growth in Mexico for the
period of 1971-2011. In so doing, unit root and causality tests are
applied. The results show that energy consumption and economic
growth series are stationary and there is also a causality relationship
running from economic growth to electricity consumption. Therefore,
any energy conservation policy would have little or no impact at all
on economic growth in México.
Abstract: This paper presents the design and fabrication of a
novel piezoelectric actuator for a gas micro pump with check valve
having the advantages of miniature size, light weight and low power
consumption. The micro pump is designed to have eight major
components, namely a stainless steel upper cover layer, a piezoelectric
actuator, a stainless steel diaphragm, a PDMS chamber layer, two
stainless steel channel layers with two valve seats, a PDMS check
valve layer with two cantilever-type check valves and an acrylic
substrate. A prototype of the gas micro pump, with a size of 52 mm ×
50 mm × 5.0 mm, is fabricated by precise manufacturing. This device
is designed to pump gases with the capability of performing the
self-priming and bubble-tolerant work mode by maximizing the stroke
volume of the membrane as well as the compression ratio via
minimization of the dead volume of the micro pump chamber and
channel. By experiment apparatus setup, we can get the real-time
values of the flow rate of micro pump and the displacement of the
piezoelectric actuator, simultaneously. The gas micro pump obtained
higher output performance under the sinusoidal waveform of 250 Vpp.
The micro pump achieved the maximum pumping rates of 1185
ml/min and back pressure of 7.14 kPa at the corresponding frequency
of 120 and 50 Hz.
Abstract: This paper proposes a linear model for optimizing
domestic energy consumption in Romania. The particularity of the
model is that it is putting in competition both tangible technologies
and thermal insulation projects with different financing modes.
The model is optimizing the energy system by minimizing the
global discounted cost in household sector, by integrating residential
lighting, space heating, hot water, combined space heating – hot
water, as well as space cooling, in a monolithic model. Another
demand sector included is the passenger transport.
This paper focuses on space heating part, analyzing technical and
economic issues related to investment decisions to envelope and
insulate buildings, in order to minimize energy consumption.
Abstract: Based on Business and Consumer Survey (BCS) data,
the European Commission (EC) regularly publishes the monthly
Economic Sentiment Indicator (ESI) for each EU member state. ESI
is conceptualized as a leading indicator, aimed ad tracking the overall
economic activity. In calculating ESI, the EC employs arbitrarily
chosen weights on 15 BCS response balances. This paper raises the
predictive quality of ESI by applying nonlinear programming to find
such weights that maximize the correlation coefficient of ESI and
year-on-year GDP growth. The obtained results show that the highest
weights are assigned to the response balances of industrial sector
questions, followed by questions from the retail trade sector. This
comes as no surprise since the existing literature shows that the
industrial production is a plausible proxy for the overall Croatian
economic activity and since Croatian GDP is largely influenced by
the aggregate personal consumption.
Abstract: A sensory network consists of multiple detection
locations called sensor nodes, each of which is tiny, featherweight
and portable. A single path routing protocols in wireless sensor
network can lead to holes in the network, since only the nodes
present in the single path is used for the data transmission. Apart
from the advantages like reduced computation, complexity and
resource utilization, there are some drawbacks like throughput,
increased traffic load and delay in data delivery. Therefore, multipath
routing protocols are preferred for WSN. Distributing the traffic
among multiple paths increases the network lifetime. We propose a
scheme, for the data to be transmitted through a dominant path to
save energy. In order to obtain a high delivery ratio, a basic route
reconstruction protocol is utilized to reconstruct the path whenever a
failure is detected. A basic reconstruction routing (BRR) algorithm is
proposed, in which a node can leap over path failure by using the
already existing routing information from its neighbourhood while
the composed data is transmitted from the source to the sink. In order
to save the energy and attain high data delivery ratio, data is
transmitted along a multiple path, which is achieved by BRR
algorithm whenever a failure is detected. Further, the analysis of
how the proposed protocol overcomes the drawback of the existing
protocols is presented. The performance of our protocol is compared
to AOMDV and energy efficient node-disjoint multipath routing
protocol (EENDMRP). The system is implemented using NS-2.34.
The simulation results show that the proposed protocol has high
delivery ratio with low energy consumption.
Abstract: This paper addresses the design of hospital Intensive
Care Unit windows for the achievement of visual comfort and energy
savings. The aim was to identify the window size and shading system
configurations that could fulfill daylighting adequacy, avoid glare
and reduce energy consumption. The study focused on addressing the
effect of utilizing different shading systems in association with a
range of Window-to-Wall Ratios (WWR) in different orientations
under the desert clear-sky of Cairo, Egypt.
The results of this study demonstrated that solar penetration is a
critical concern affecting the design of ICU windows in desert
locations, as in Cairo, Egypt. Use of shading systems was found to be
essential in providing acceptable daylight performance and energy
saving. Careful positioning of the ICU window towards a proper
orientation can dramatically improve performance. It was observed
that ICU windows facing the north direction enjoyed the widest range
of successful window configuration possibilities at different WWRs.
ICU windows facing south enjoyed a reasonable number of
configuration options as well. By contrast, the ICU windows facing
the east orientation had a very limited number of options that provide
acceptable performance. These require additional local shading
measures at certain times due to glare incidence. Moreover, use of
horizontal sun breakers and solar screens to protect the ICU windows
proved to be more successful than the other alternatives in a wide
range of Window to Wall Ratios. By contrast, the use of light shelves
and vertical shading devices seemed questionable.
Abstract: Fruit juices play important roles in human health as
being a key part of nutrition. Juice and nectar are two categories of
drinks with so many variations for consumers, regardless of age,
lifestyle and taste preferences, which they can find their favorites.
Juices contain 100% pulp when pulp content of ‘nectar’ changes
between 25%-50%. In this study, potassium (K), magnesium (Mg),
and phosphorus (P) contents in orange juice and nectar is determined
for conscious consumption. For this purpose inductively coupled
plasma optical emission spectrometry (ICP-OES) is used to find out
potassium (K), magnesium (Mg), and phosphorus (P) contents in
orange juices and nectar. Furthermore, the daily intake of elements
from orange juice and nectar that affects human health is also
investigated. From the results of experiments K, Mg and P contents
are found in orange juice as 1351; 73,25; 89,27 ppm and in orange
nectar as 986; 33,76; 51,30 respectively.
Abstract: Recently, universities are increasingly consuming
energy to support various activities. A large population of staff and
students in Malaysian universities has led to excessive energy
consumption which directly gives an impact to the environment. The
key question then ascended “How well is an energy management
(EM) been practiced in universities without taking the Critical
Success Factors (CSFs) into consideration to ensure the management
of university achieves the goals in reducing energy consumption.
Review on past literature is carried out to establish CSFs for EM best
practices. Thus, this paper highlighted the CSFs which have to be
focused on by management of university to successfully measure the
EM implementation and its performance. At the end of this paper, a
theoretical framework is developed for EM success factors towards
sustainable university.
Abstract: Kazakhstan is currently one of the dynamically
developing states in its region. The stable growth in all sectors of the
economy leads to a corresponding increase in energy consumption.
Thus country consumes significant amount of energy due to the high
level of industrialisation and the presence of energy-intensive
manufacturing such as mining and metallurgy which in turn leads to
low energy efficiency. With allowance for this the Government has
set several priorities to adopt a transition of Republic of Kazakhstan
to a “green economy”. This article provides an overview of
Kazakhstan’s energy efficiency situation in for the period of 1991-
2014. First, the dynamics of production and consumption of
conventional energy resources are given. Second, the potential of
renewable energy sources is summarised followed by the description
of GHG emissions trends in the country. Third, Kazakhstan’ national
initiatives, policies and locally implemented projects in the field of
energy efficiency are described.
Abstract: Composite materials, due to their unique properties
such as high strength to weight ratio, corrosion resistance, and impact
resistance have huge potential as structural materials in automotive,
construction and transportation applications. However, these
properties often come at higher cost owing to complex design
methods, difficult manufacturing processes and raw material cost.
Traditionally, tapered laminated composite structures are
manufactured using autoclave manufacturing process by ply drop off
technique. Autoclave manufacturing though very powerful suffers
from high capital investment and higher energy consumption. As per
the current trends in composite manufacturing, Out of Autoclave
(OoA) processes are looked as emerging technologies for
manufacturing the structural composite components for aerospace
and defense applications. However, there is a need for improvement
among these processes to make them reliable and consistent. In this
paper, feasibility of using out of autoclave process to manufacture the
variable thickness cantilever beam is discussed. The minimum weight
design for the composite beam is obtained using constant stress beam
concept by tailoring the thickness of the beam. Ply drop off
techniques was used to fabricate the variable thickness beam from
glass/epoxy prepregs. Experiments were conducted to measure
bending stresses along the span of the cantilever beam at different
intervals by applying the concentrated load at the free end.
Experimental results showed that the stresses in the bean at different
intervals were constant. This proves the ability of OoA process to
manufacture the constant stress beam. Finite element model for the
constant stress beam was developed using commercial finite element
simulation software. It was observed that the simulation results
agreed very well with the experimental results and thus validated
design and manufacturing approach used.
Abstract: Starting in 2020, an EU-wide CO2-limitation of
95 g/km is scheduled for the average of an OEMs passenger car fleet.
Taking that into consideration additional improvement measures of
the Diesel cycle are necessary in order to reduce fuel consumption
and emissions while boosting, or at the least, keeping performance
values at the same time.
The present article deals with the possibilities of an optimized
air/water charge air cooler, also called iCAC (indirect Charge Air
Cooler) for a Diesel passenger car amongst extreme-boundary
conditions. In this context, the precise objective was to show the
impact of improved intercooling with reference to the engine working
process (fuel consumption and NOx-emissions). Several extremeboundaries
- e.g. varying ambient temperatures or mountainous
routes - that will become very important in the near future regarding
RDE (Real Driving emissions) were subject of the investigation.
With the introduction of RDE in 2017 (EU6c measure), the
controversial NEDC (New European Driving Cycle) will belong to
the past and the OEMs will have to avoid harmful emissions in any
conceivable real life situation.
This is certainly going to lead to optimization-measurements at the
powertrain, which again is going to make the implementation of
iCACs, presently solely used for the premium class, more and more
attractive for compact class cars. The investigations showed a benefit
in FC between 1 and 3% for the iCAC in real world conditions.
Abstract: The paper examines the interaction between the
environmental taxation, size of government spending on
environmental protection and greenhouse gas emissions and gross
inland energy consumption. The aim is to analyze the effects of
environmental taxation and government spending on environmental
protection as an environmental policy instruments on greenhouse gas
emissions and gross inland energy consumption in the EU15. The
empirical study is performed using a VAR approach with the
application of aggregated data of EU15 over the period 1995 to 2012.
The results provide the evidence that the reactions of greenhouse gas
emission and gross inland energy consumption to the shocks of
environmental policy instruments are strong, mainly in the short term
and decay to zero after about 8 years. Further, the reactions of the
environmental policy instruments to the shocks of greenhouse gas
emission and gross inland energy consumption are also strong in the
short term, however with the deferred effects. In addition, the results
show that government spending on environmental protection together
with gross inland energy consumption has stronger effect on
greenhouse gas emissions than environmental taxes in EU15 over the
examined period.
Abstract: This work was one of the tasks of the
Manufacturing2Client project, whose objective was to develop a
frontal deflector to be commercialized in the automotive industry,
using new project and manufacturing methods. In this task, in
particular, it was proposed to develop the ability to predict
computationally the aerodynamic influence of flow in vehicles, in an
effort to reduce fuel consumption in vehicles from class 3 to 8. With
this aim, two deflector models were developed and their aerodynamic
performance analyzed. The aerodynamic study was done using the
Computational Fluid Dynamics (CFD) software Ansys CFX and
allowed the calculation of the drag coefficient caused by the vehicle
motion for the different configurations considered. Moreover, the
reduction of diesel consumption and carbon dioxide (CO2) emissions
associated with the optimized deflector geometry could be assessed.
Abstract: In regards to the energy sector in the modern period,
two points were raised. First is a vast and growing energy demand, and
second is an environmental impact associated with it. The enormous
consumption of fossil fuel to the mobile unit is leading to its rapid
depletion. Nuclear power is not the only problem. A modal shift that
utilizes personal transporters and independent power, in order to
realize a sustainable society, is very effective. The author proposes that
the world will continue to work on this. Energy of the future society,
innovation in battery technology and the use of natural energy is a big
key. And it is also necessary in order to save on energy consumption.
Abstract: The exposure to outdoor air pollution causes lung
cancer and increases the risk of bladder cancer. Because air pollution
in urban areas is mainly caused by transportation, it is necessary to
evaluate pollutant exhaust emissions from vehicles during their realworld
use. Nevertheless their evaluation and reduction is a key
problem, especially in the cities, that account for more than 50% of
world population.
A particular attention was given to the slope variability along the
streets during each journey performed by the instrumented vehicle.
In this paper we dealt with the problem of describing a
quantitatively approach for the reconstruction of GPS coordinates and
altitude, in the context of correlation study between driving cycles /
emission / geographical location, during an experimental campaign
realized with some instrumented cars.
Finally the slope analysis can be correlated to the emission and
consumption values in a specific road position, and it could be
evaluated its influence on their behaviour.
Abstract: The postharvest quality management of tomatoes is
important to limit the amount of losses that occur due to deterioration
between harvest and consumption. This study was undertaken to
investigate the effects of pre- and postharvest integrated agrotechnologies,
involving greenhouse microclimate and postharvest
storage conditions, on the postharvest quality attributes of four
tomato cultivars. Tomato fruit firmness, colour (hue angle (h°) and
L* value), pH and total soluble solids for the cultivars Bona,
Star 9037, Star 9009 and Zeal, grown in a fan-pad evaporativelycooled
and an open-ended naturally-ventilated tunnel, were harvested
at the mature-green stage. The tomatoes were stored for 28 days
under cold storage conditions, with a temperature of 13°C and RH of
85%, and under ambient air conditions, with a temperature of 23±
2°C and RH of 52± 4%. This study has provided information on the
effect of integrated pre-harvest and postharvest agro-technologies,
involving greenhouse microclimate and postharvest storage
environment on the postharvest quality attributes of four of the
tomato cultivars in South Africa. NVT-grown tomatoes retained
better textural qualities, but ripened faster by changing from green to
red faster, although these were reduced under cold storage conditions.
FPVT-grown tomatoes had lower firmness, but ripened slowly with
higher colour attributes. With cold storage conditions, the firmness of
FPVT-grown tomatoes was maintained. Cultivar Bona firmness and
colour qualities depreciated the fastest, but it had higher TSS content
and lower pH values. Star 9009 and Star 9037 presented better
quality, by retaining higher firmness and ripening slowly, but they
had the lowest TSS contents and high pH values, especially
Star 9037. Cold storage improved the firmness of tomato cultivars
with poor textural quality and faster colour changes.
Abstract: Recent advances in wireless networking technologies
introduce several energy aware routing protocols in sensor networks.
Such protocols aim to extend the lifetime of network by reducing the
energy consumption of nodes. Many researchers are looking for
certain challenges that are predominant in the grounds of energy
consumption. One such protocol that addresses this energy
consumption issue is ‘Cluster based hierarchical routing protocol’. In
this paper, we intend to discuss some of the major hierarchical
routing protocols adhering towards sensor networks. Furthermore, we
examine and compare several aspects and characteristics of few
widely explored hierarchical clustering protocols, and its operations
in wireless sensor networks (WSN). This paper also presents a
discussion on the future research topics and the challenges of
hierarchical clustering in WSNs.
Abstract: Anultra-low power capacitor less low-dropout voltage
regulator with improved transient response using gain enhanced feed
forward path compensation is presented in this paper. It is based on a
cascade of a voltage amplifier and a transconductor stage in the feed
forward path with regular error amplifier to form a composite gainenhanced
feed forward stage. It broadens the gain bandwidth and thus
improves the transient response without substantial increase in power
consumption. The proposed LDO, designed for a maximum output
current of 100 mA in UMC 180 nm, requires a quiescent current of
69 )A. An undershot of 153.79mV for a load current changes from
0mA to 100mA and an overshoot of 196.24mV for current change of
100mA to 0mA. The settling time is approximately 1.1 )s for the
output voltage undershooting case. The load regulation is of 2.77
)V/mA at load current of 100mA. Reference voltage is generated by
using an accurate band gap reference circuit of 0.8V.The costly
features of SOC such as total chip area and power consumption is
drastically reduced by the use of only a total compensation
capacitance of 6pF while consuming power consumption of 0.096
mW.
Abstract: Heating, cooling and lighting appliances in buildings
account for more than one third of the world’s primary energy
demand. Therefore, main components of the building heating systems
play an essential role in terms of energy consumption. In this context,
efficient energy and exergy utilization in HVAC-R systems has been
very essential, especially in developing energy policies towards
increasing efficiencies. The main objective of the present study is to
assess the performance of a family house with a volume of 326.7 m3
and a net floor area of 121 m2, located in the city of Izmir, Turkey in
terms of energetic, exergetic and sustainability aspects. The indoor
and exterior air temperatures are taken as 20°C and 1°C, respectively.
In the analysis and assessment, various metrics (indices or indicators)
such as exergetic efficiency, exergy flexibility ratio and sustainability
index are utilized. Two heating options (Case 1: condensing boiler
and Case 2: air heat pump) are considered for comparison purposes.
The total heat loss rate of the family house is determined to be
3770.72 W. The overall energy efficiencies of the studied cases are
calculated to be 49.4% for Case 1 and 54.7% for Case 2. The overall
exergy efficiencies, the flexibility factor and the sustainability index
of Cases 1 and 2 are computed to be around 3.3%, 0.17 and 1.034,
respectively.
Abstract: The paper presents actual benefits and drawbacks of a multidirectional autonomous hovercraft conceived with limited resources and designed for indoor exploration. Recent developments in the field have led to the apparition of very powerful automotive systems capable of very high calculation and exploration in complex unknown environments. They usually propose very complex algorithms, high precision/cost sensors and sometimes have heavy calculation consumption with complex data fusion. These systems are usually powerful but have a certain price, and the benefits may not be worth the cost, especially considering their hardware limitations and their power consumption. The present approach is to build a compromise between cost, power consumption and results preciseness.