Abstract: In this paper, an attempt has been made to obtain nonsensitive
solutions in the multi-objective optimization of a
photovoltaic/thermal (PV/T) air collector. The selected objective
functions are overall energy efficiency and exergy efficiency.
Improved thermal, electrical and exergy models are used to calculate
the thermal and electrical parameters, overall energy efficiency,
exergy components and exergy efficiency of a typical PV/T air
collector. A computer simulation program is also developed. The
results of numerical simulation are in good agreement with the
experimental measurements noted in the previous literature. Finally,
multi-objective optimization has been carried out under given
climatic, operating and design parameters. The optimized ranges of
inlet air velocity, duct depth and the objective functions in optimal
Pareto front have been obtained. Furthermore, non-sensitive solutions
from energy or exergy point of view in the results of multi-objective
optimization have been shown.
Abstract: Hot tear cracking and residual stress are two different consequences of thermal stress both of which can be considered as casting problem. The purpose of the present study is simulation of the effect of casting shape characteristic on hot tearing and residual stress. This study shows that the temperature range for simulation of hot tearing and residual stress are different. In this study, in order to study the development of thermal stress and to predict the hot tearing and residual stress of shaped casting, MAGMASOFT simulation program was used. The strategy of this research was the prediction of hot tear location using pinpointing hot spot and thermal stress concentration zones. The results shows that existing of stress concentration zone increases the hot tearing probability and consequently reduces the amount of remaining residual stress in casting parts.
Abstract: The current practice of determination of moisture diffusivity of building materials under laboratory conditions is predominantly aimed at the absorption phase. The main reason is the simplicity of the inverse analysis of measured moisture profiles. However, the liquid moisture transport may exhibit significant hysteresis. Thus, the moisture diffusivity should be different in the absorption (wetting) and desorption (drying) phase. In order to bring computer simulations of hygrothermal performance of building materials closer to the reality, it is then necessary to find new methods for inverse analysis which could be used in the desorption phase as well. In this paper we present genetic algorithm as a possible method of solution of the inverse problem of moisture transport in desorption phase. Its application is demonstrated for AAC as a typical building material.
Abstract: Optimal selection of electrical insulations in electrical
machinery insures reliability during operation. From the insulation
studies of view for electrical machines, stator is the most important
part. This fact reveals the requirement for inspection of the electrical
machine insulation along with the electro-thermal stresses. In the
first step of the study, a part of the whole structure of machine in
which covers the general characteristics of the machine is chosen,
then based on the electromagnetic analysis (finite element method),
the machine operation is simulated. In the simulation results, the
temperature distribution of the total structure is presented
simultaneously by using electro-thermal analysis. The results of
electro-thermal analysis can be used for designing an optimal cooling
system. In order to design, review and comparing the cooling
systems, four wiring structures in the slots of Stator are presented.
The structures are compared to each other in terms of electrical,
thermal distribution and remaining life of insulation by using Finite
Element analysis. According to the steps of the study, an optimization
algorithm has been presented for selection of appropriate structure.
Abstract: Composites based on a biodegradable polycaprolactone (PCL) containing 0.5, 1.0 and 2.0 wt % of titanium dioxide (TiO2) micro and nanoparticles were prepared by melt mixing and the effect of filler type and contents on the thermal properties, dynamic-mechanical behaviour and morphology were investigated. Measurements of storage modulus and loss modulus by dynamic mechanical analysis (DMA) showed better results for microfilled PCL/TiO2 composites than nanofilled composites, with the same filler content. DSC analysis showed that the Tg and Tc of micro and nanocomposites were slightly lower than those of neat PCL. The crystallinity of the PCL increased with the addition of TiO2 micro and nanoparticles; however, the cc for the PCL was unchanged with micro TiO2 content. The thermal stability of PCL/TiO2 composites were characterized using thermogravimetric analysis (TGA). The initial weight loss (5 wt %) occurs at slightly higher temperature with micro and nano TiO2 addition and with increasing TiO2 content.
Abstract: Space exploration is a highly visible endeavour of
humankind to seek profound answers to questions about the origins
of our solar system, whether life exists beyond Earth, and how we
could live on other worlds. Different platforms have been utilized in
planetary exploration missions, such as orbiters, landers, rovers, and
penetrators.
Having low mass, good mechanical contact with the surface,
ability to acquire high quality scientific subsurface data, and ability to
be deployed in areas that may not be conducive to landers or rovers,
Penetrators provide an alternative and complimentary solution that
makes possible scientific exploration of hardly accessible sites (icy
areas, gully sites, highlands etc.).
The Canadian Space Agency (CSA) has put space exploration as
one of the pillars of its space program, and established ExCo program
to prepare Canada for future international planetary exploration.
ExCo sets surface mobility as its focus and priority, and invests
mainly in the development of rovers because of Canada's niche space
robotics technology. Meanwhile, CSA is also investigating how
micro-penetrators can help Canada to fulfill its scientific objectives
for planetary exploration.
This paper presents a review of the micro-penetrator technologies,
past missions, and lessons learned. It gives a detailed analysis of the
technical challenges of micro-penetrators, such as high impact
survivability, high precision guidance navigation and control, thermal
protection, communications, and etc. Then, a Canadian perspective of
a possible micro-penetrator mission is given, including Canadian
scientific objectives and priorities, potential instruments, and flight
opportunities.
Abstract: There is an ongoing controversy in the literature related
to the biological effects of weak, low frequency electromagnetic
fields. The physical arguments and interpretation of the experimental
evidence are inconsistent, where some physical arguments and
experimental demonstrations tend to reject the likelihood of any
effect of the fields at extremely low level. The problem arises of
explaining, how the low-energy influences of weak magnetic fields
can compete with the thermal and electrical noise of cells at normal
temperature using the theoretical studies. The magnetoreception in
animals involve radical pair mechanism. The same mechanism has
been shown to be involved in the circadian rhythm synchronization in
mammals. These reactions can be influenced by the weak magnetic
fields. Hence, it is postulated the biological clock can be affected
by weak magnetic fields and these disruptions to the rhythm can
cause adverse biological effects. In this paper, likelihood of altering
the biological clock via the radical pair mechanism is analyzed to
simplify these studies of controversy.
Abstract: The leaching behavior and structure of Li2O-CeO2- Fe2O3-P2O5 glasses incorporated with simulated high level nuclear wastes (HLW) were studied. The leach rates of gross and each constituent element were determined from the total weight loss of the specimen and the leachate analyses by inductively coupled argon plasma spectroscopy (ICP). The gross leach rate of the 4.5Li2O- 9.7CeO2-34.7Fe2O3-51.5P2O5 glass waste form containing 45 mass% simulated HLW is of the order of 10
Abstract: Thermal water hammer is a special type of water
hammer which rarely occurs in heat exchangers. In biphasic fluids, if
steam bubbles are surrounded by condensate, regarding lower
condensate temperature than steam, they will suddenly collapse. As a
result, the vacuum caused by an extreme change in volume lead to
movement of the condensates in all directions and their collision the
force produced by this collision leads to a severe stress in the pipe
wall. This phenomenon is a special type of water hammer. According
to fluid mechanics, this phenomenon is a particular type of transient
flows during which abrupt change of fluid leads to sudden pressure
change inside the tube. In this paper, the mechanism of abrupt failure
of 80 tubes of 481 tubes of a methanol heat exchanger is discussed.
Initially, due to excessive temperature differences between heat
transfer fluids and simultaneous failure of 80 tubes, thermal shock
was presupposed as the reason of failure. Deeper investigation on
cross-section of failed tubes showed that failure was, ductile type of
failure, so the first hypothesis was rejected. Further analysis and more
accurate experiments revealed that failure of tubes caused by thermal
water hammer. Finally, the causes of thermal water hammer and
various solutions to avoid such mechanism are discussed.
Abstract: ORC (Organic Rankine Cycle) has potential of
reducing consumption of fossil fuels and has many favorable
characteristics to exploit low-temperature heat sources. In this work
thermodynamic performance of ORC with regeneration is
comparatively assessed for various working fluids. Special attention is
paid to the effects of system parameters such as the turbine inlet
pressure on the characteristics of the system such as net work
production, heat input, volumetric flow rate per 1 MW of net work and
quality of the working fluid at turbine exit as well as thermal
efficiency. Results show that for a given source the thermal efficiency
generally increases with increasing of the turbine inlet pressure
however has optimal condition for working fluids of low critical
pressure such as iso-pentane or n-pentane.
Abstract: Composite of Celatom-ZeoliteY (Cel-ZY) was used to
remove cobalt ion from an aqueous solution using batch mode.
ZeoliteY has successfully superimposed on Celatom FW-14 surface
using hydrothermal treatment .The product was synthesized as a
novel of hierarchical porous material. It was observed from the
results that Cel-ZY has higher ability to remove cobalt ions than the
pure ZeoliteY powder (PZY) synthesized under the same conditions.
Several parameters were studied in this project to investigate the
effect of removal cobalt ion such as pH and initial cobalt
concentration. It was clearly observed that the uptake of cobalt ions
was affected with increase these parameters. The results proved that
the product can be used effectively to remove Co2+ ions from
wastewater as an environmentally friendly alternative.
Abstract: Sol-gel method has been used to fabricate
nanocomposite films on glass substrates composed halloysite clay
mineral and nanocrystalline TiO2. The methodology for the synthesis
involves a simple chemistry method utilized nonionic surfactant
molecule as pore directing agent along with the acetic acid-based solgel
route with the absence of water molecules. The thermal treatment
of composite films at 450oC ensures elimination of organic material
and lead to the formation of TiO2 nanoparticles onto the surface of
the halloysite nanotubes. Microscopy techniques and porosimetry
methods used in order to delineate the structural characteristics of the
materials. The nanocomposite films produced have no cracks and
active anatase crystal phase with small crystallite size were deposited
on halloysite nanotubes. The photocatalytic properties for the new
materials were examined for the decomposition of the Basic Blue 41
azo dye in solution. These, nanotechnology based composite films
show high efficiency for dye’s discoloration in spite of different
halloysite quantities and small amount of halloysite/TiO2 catalyst
immobilized onto glass substrates. Moreover, we examined the
modification of the halloysite/TiO2 films with silver particles in order
to improve the photocatalytic properties of the films. Indeed, the
presence of silver nanoparticles enhances the discoloration rate of the
Basic Blue 41 compared to the efficiencies obtained for unmodified
films.
Abstract: The effect of Alumina nanoparticle size on thermophysical
properties, heat transfer performance and pressure loss characteristics of
Aviation Turbine Fuel (ATF)-Al2O3 nanofluids is studied experimentally for
the proposed application of regenerative cooling of semi-cryogenic rocket
engine thrust chambers. Al2O3 particles with mean diameters of 50 nm or 150
nm are dispersed in ATF. At 500C and 0.3% particle volume concentration,
the bigger particles show increases of 17% in thermal conductivity and 55% in
viscosity, whereas the smaller particles show corresponding increases of 21%
and 22% for thermal conductivity and viscosity respectively. Contrary to these
results, experiments to study the heat transfer performance and pressure loss
characteristics show that at the same pumping power, the maximum
enhancement in heat transfer coefficient at 500C and 0.3% concentration is
approximately 47% using bigger particles, whereas it is only 36% using
smaller particles.
Abstract: The daily increase of organic waste materials resulting
from different activities in the country is one of the main factors for
the pollution of environment. Today, with regard to the low level of
the output of using traditional methods, the high cost of disposal
waste materials and environmental pollutions, the use of modern
methods such as anaerobic digestion for the production of biogas has
been prevailing. The collected biogas from the process of anaerobic
digestion, as a renewable energy source similar to natural gas but
with a less methane and heating value is usable. Today, with the help
of technologies of filtration and proper preparation, access to biogas
with features fully similar to natural gas has become possible. At
present biogas is one of the main sources of supplying electrical and
thermal energy and also an appropriate option to be used in four
stroke engine, diesel engine, sterling engine, gas turbine, gas micro
turbine and fuel cell to produce electricity. The use of biogas for
different reasons which returns to socio-economic and environmental
advantages has been noticed in CHP for the production of energy in
the world. The production of biogas from the technology of anaerobic
digestion and its application in CHP power plants in Iran can not only
supply part of the energy demands in the country, but it can
materialize moving in line with the sustainable development. In this
article, the necessity of the development of CHP plants with biogas
fuels in the country will be dealt based on studies performed from the
economic, environmental and social aspects. Also to prove the
importance of the establishment of these kinds of power plants from
the economic point of view, necessary calculations has been done as
a case study for a CHP power plant with a biogas fuel.
Abstract: This research were investigated, determined, and
analyzed of the climate characteristically change in the provincial
Udon Thani in the period of 60 surrounding years from 1951 to 2010
A.D. that it-s transferred to effects of climatologically data for
determining global warming. Statistically significant were not found
for the 60 years- data (R2
Abstract: The main issue in sweetening natural gas is H2S
dissociation. The present study is concerned with simulating thermal
dissociation of H2S in industrial natural gas carbon black furnace.
The comparison of calculated results against experimental
measurements shows good agreement. The results show that sulfur
derived from H2S thermal dissociation peaked at φ=0.95. H2S
thermal dissociation is enhanced in equivalence ratio upper than 1
and H2S oxidization is increased in equivalence ratio lower than 1.
H2 concentration of H2S thermal dissociation is increased with
increase of equivalence ratio up to 1. Also, H2S concentration
decreased in outlet as equivalence ratio increases. H2S thermal
dissociation to hydrogen and Sulfur reduces its toxic characteristics
and make economical benefits.
Abstract: The high temperature degree and uniform
Temperature Distribution (TD) on surface of cookware which contact
with food are effective factors for improving cookware application.
Additionally, the ability of pan material in retaining the heat and nonreactivity
with foods are other significant properties. It is difficult for
single material to meet a wide variety of demands such as superior
thermal and chemical properties. Multi-Layer Plate (MLP) makes
more regular TD. In this study the main objectives are to find the best
structure (single or multi-layer) and materials to provide maximum
temperature degree and uniform TD up side surface of pan. And also
heat retaining of used metals with goal of improving the thermal
quality of pan to economize the energy. To achieve this aim were
employed Finite Element Method (FEM) for analyzing transient
thermal behavior of applied materials. The analysis has been
extended for different metals, we achieved the best temperature
profile and heat retaining in Copper/ Stainless Steel MLP.
Abstract: A behavioral model of a second order switchedcapacitor Sigma-Delta modulator is presented. The purpose of this work is the presentation of a behavioral model of a second order switched capacitor ΣΔ modulator considering (Error due to Clock Jitter, Thermal noise Amplifier Noise, Amplifier Slew-Rate, Non linearity of amplifiers, Gain error, Charge Injection, Clock Feedthrough, and Nonlinear on-resistance). A comparison between the use of MOS switches and the use transmission gate switches use is analyzed.
Abstract: The paper reports the preparation and photocatalytic
activity of ZnO/SnO2 and SnO2 nanoparticles. These nanoparticles
were synthesized by hydrothermal method. The products were
characterized by X-ray diffraction (XRD) and scanning electron
microscopy (SEM). Their grain sizes are about 50-100 nm. The
photocatalytic activities of these materials were investigated for
congo red removal from aqueous solution under UV light irradiation.
It was shown that the use of ZnO/SnO2 as photocatalyst have better
photocatalytic activity for degradation of congo red than SnO2 or
TiO2 (anatase, particle size: 30nm) alone.
Abstract: Facing the concern of the population to its environment and to climatic change, city planners are now considering the urban climate in their choices of planning. The urban climate, representing different urban morphologies across central Bangkok metropolitan area (BMA), are used to investigates the effects of both the composition and configuration of variables of urban morphology indicators on the summer diurnal range of urban climate, using correlation analyses and multiple linear regressions. Results show first indicate that approximately 92.6% of the variation in the average maximum daytime near-surface air temperature (Ta) was explained jointly by the two composition variables of urban morphology indicators including open space ratio (OSR) and floor area ratio (FAR). It has been possible to determine the membership of sample areas to the local climate zones (LCZs) using these urban morphology descriptors automatically computed with GIS and remote sensed data. Finally result found the temperature differences among zones of large separation, such as the city center could be respectively from 35.48±1.04ºC (Mean±S.D.) warmer than the outskirt of Bangkok on average for maximum daytime near surface temperature to 28.27±0.21ºC for extreme event and, can exceed as 8ºC. A spatially disaggregation of urban thermal responsiveness map would be helpful for several reasons. First, it would localize urban areas concerned by different climate behavior over summer daytime and be a good indicator of urban climate variability. Second, when overlaid with a land cover map, this map may contribute to identify possible urban management strategies to reduce heat wave effects in BMA.