Abstract: A 10bit, 40 MSps, sample and hold, implemented in 0.18-μm CMOS technology with 3.3V supply, is presented for application in the front-end stage of an analog-to-digital converter. Topology selection, biasing, compensation and common mode feedback are discussed. Cascode technique has been used to increase the dc gain. The proposed opamp provides 149MHz unity-gain bandwidth (wu), 80 degree phase margin and a differential peak to peak output swing more than 2.5v. The circuit has 55db Total Harmonic Distortion (THD), using the improved fully differential two stage operational amplifier of 91.7dB gain. The power dissipation of the designed sample and hold is 4.7mw. The designed system demonstrates relatively suitable response in different process, temperature and supply corners (PVT corners).
Abstract: In this paper, a double balanced radio frequency multiplier
is presented which is customized for transmitted reference
ultra wideband (UWB) receivers. The multiplier uses 90nm model
parameters and exploits compensating transistors to provide controllable
gain for a Gilbert core. After performing periodic and quasiperiodic
non linear analyses the RF mixer (multiplier) achieves a
voltage conversion gain of 16 dB and a DSB noise figure of 8.253
dB with very low power consumption. A high degree of LO to RF
isolation (in the range of -94dB), RF to IF isolation (in the range of
-95dB) and LO to IF isolation (in the range of -143dB) is expected
for this design with an input-referred IP3 point of -1.93 dBm and an
input referred 1 dB compression point of -10.67dBm. The amount of
noise at the output is 7.7 nV/√Hz when the LO input is driven by
a 10dBm signal. The mixer manifests better results when compared
with other reported multiplier circuits and its Zero-IF performance
ensures its applicability as TR-UWB multipliers.
Abstract: Major social changes in the last century had significant impact on the Kazakh literature. Participants of the World War II, writers and poets imprisoned during the war, formed the Kazakh literature in emigration within the framework of 'Turkistan Legion'. This was a topic which remained closed until Kazakhstan gained its independence, though even after the independence, there were few research works done about the literature in emigration. The article studies the formation of the Kazakh literature in emigration, its prominent figures, its artistic heritage, and notes of emigration in works of poets and writers.
Abstract: A 1V, 1GHz low noise amplifier (LNA) has been designed and simulated using Spectre simulator in a standard TSMC 0.18um CMOS technology.With low power and noise optimization techniques, the amplifier provides a gain of 24 dB, a noise figure of only 1.2 dB, power dissipation of 14 mW from a 1 V power supply.
Abstract: The present paper develops and validates a numerical procedure for the calculation of turbulent combustive flow in converging and diverging ducts and throuh simulation of the heat transfer processes, the amount of production and spread of Nox pollutant has been measured. A marching integration solution procedure employing the TDMA is used to solve the discretized equations. The turbulence model is the Prandtl Mixing Length method. Modeling the combustion process is done by the use of Arrhenius and Eddy Dissipation method. Thermal mechanism has been utilized for modeling the process of forming the nitrogen oxides. Finite difference method and Genmix numerical code are used for numerical solution of equations. Our results indicate the important influence of the limiting diverging angle of diffuser on the coefficient of recovering of pressure. Moreover, due to the intense dependence of Nox pollutant to the maximum temperature in the domain with this feature, the Nox pollutant amount is also in maximum level.
Abstract: In this paper, we have combined some spatial derivatives with the optimised time derivative proposed by Tam and Webb in order to approximate the linear advection equation which is given by = 0. Ôêé Ôêé + Ôêé Ôêé x f t u These spatial derivatives are as follows: a standard 7-point 6 th -order central difference scheme (ST7), a standard 9-point 8 th -order central difference scheme (ST9) and optimised schemes designed by Tam and Webb, Lockard et al., Zingg et al., Zhuang and Chen, Bogey and Bailly. Thus, these seven different spatial derivatives have been coupled with the optimised time derivative to obtain seven different finite-difference schemes to approximate the linear advection equation. We have analysed the variation of the modified wavenumber and group velocity, both with respect to the exact wavenumber for each spatial derivative. The problems considered are the 1-D propagation of a Boxcar function, propagation of an initial disturbance consisting of a sine and Gaussian function and the propagation of a Gaussian profile. It is known that the choice of the cfl number affects the quality of results in terms of dissipation and dispersion characteristics. Based on the numerical experiments solved and numerical methods used to approximate the linear advection equation, it is observed in this work, that the quality of results is dependent on the choice of the cfl number, even for optimised numerical methods. The errors from the numerical results have been quantified into dispersion and dissipation using a technique devised by Takacs. Also, the quantity, Exponential Error for Low Dispersion and Low Dissipation, eeldld has been computed from the numerical results. Moreover, based on this work, it has been found that when the quantity, eeldld can be used as a measure of the total error. In particular, the total error is a minimum when the eeldld is a minimum.
Abstract: In the recent years multimedia traffic and in particular
VoIP services are growing dramatically. We present a new algorithm
to control the resource utilization and to optimize the voice codec
selection during SIP call setup on behalf of the traffic condition
estimated on the network path.
The most suitable methodologies and the tools that perform realtime
evaluation of the available bandwidth on a network path have
been integrated with our proposed algorithm: this selects the best
codec for a VoIP call in function of the instantaneous available
bandwidth on the path. The algorithm does not require any explicit
feedback from the network, and this makes it easily deployable over
the Internet. We have also performed intensive tests on real network
scenarios with a software prototype, verifying the algorithm
efficiency with different network topologies and traffic patterns
between two SIP PBXs.
The promising results obtained during the experimental validation
of the algorithm are now the basis for the extension towards a larger
set of multimedia services and the integration of our methodology
with existing PBX appliances.
Abstract: Lignocellulosic materials are considered the most
abundant renewable resource available for the Bioethanol
Production. Water Hyacinth is one of potential raw material of the
world-s worst aquatic plant as a feedstock to produce Bioethanol.
The purposed this research is obtain reduced of matter for
biodegradation lignin in Biological pretreatment with White Rot
Fungi eg. Phanerochaete Chrysosporium using Solid state
Fermentation methods. Phanerochaete Chrysosporium is known to
have the best ability to degraded lignin, but simultaneously it can also
degraded cellulose and hemicelulose. During 8 weeks incubation,
water hyacinth occurred loss of weight reached 34,67%, while loss
of lignin reached 67,21%, loss of cellulose reached 11,01% and loss
of hemicellulose reached 36,56%. The kinetic of losses lignin using
regression linear plot, the results is obtained constant rate (k) of
reduction lignin is -0.1053 and the equation of reduction of lignin
is y = wo - 0, 1.53 x
Abstract: The importance of low power consumption is widely
acknowledged due to the increasing use of portable devices, which
require minimizing the consumption of energy. Energy dissipation is
heavily dependent on the software used in the system. Applying
design patterns in object-oriented designs is a common practice
nowadays. In this paper we analyze six design patterns and explore
the effect of them on energy consumption and performance.
Abstract: This paper presents a methodology towards the emulation of the electrical power consumption of the RF device during the cellular phone/handset transmission mode using the LTE technology. The emulation methodology takes the physical environmental variables and the logical interface between the baseband and the RF system as inputs to compute the emulated power dissipation of the RF device. The emulated power, in between the measured points corresponding to the discrete values of the logical interface parameters is computed as a polynomial interpolation using polynomial basis functions. The evaluation of polynomial and spline curve fitting models showed a respective divergence (test error) of 8% and 0.02% from the physically measured power consumption. The precisions of the instruments used for the physical measurements have been modeled as intervals. We have been able to model the power consumption of the RF device operating at 5MHz using homotopy between 2 continuous power consumptions of the RF device operating at the bandwidths 3MHz and 10MHz.
Abstract: In this paper, we have developed an explicit analytical
drain current model comprising surface channel potential and
threshold voltage in order to explain the advantages of the proposed
Gate Stack Double Diffusion (GSDD) MOSFET design over the
conventional MOSFET with the same geometric specifications that
allow us to use the benefits of the incorporation of the high-k layer
between the oxide layer and gate metal aspect on the immunity of the
proposed design against the self-heating effects. In order to show the
efficiency of our proposed structure, we propose the simulation of the
power chopper circuit. The use of the proposed structure to design a
power chopper circuit has showed that the (GSDD) MOSFET can
improve the working of the circuit in terms of power dissipation and
self-heating effect immunity. The results so obtained are in close
proximity with the 2D simulated results thus confirming the validity
of the proposed model.
Abstract: One of the main and responsible units of Sulzer
projectile loom is picking mechanism. It is specifically designed to
accelerate projectile to speed of 25 m / s. Initial speed projectile of
Sulzer projectile loom is independent of speed loom and determined
the potential energy torsion rod. This paper investigates the dynamics
picking mechanism of Sulzer projectile loom during its discharge. A
result of calculation model, we obtain the law of motion lever of
picking mechanism during its discharge. Construction of dynamic
model the picking mechanism of Sulzer projectile loom on software
complex SimulationX can make calculations for different thickness
of torsion rods taking into account the backlashes in the connections,
the dissipative forces and resistance forces
Abstract: This paper examines the issues, the dangers and the
saving graces of life in a transparent global community where there is
truly “no place to hide". In recent years, social networks and online
groups have transformed issues of privacy and the ways in which we
perceive and interact with others. The idea of reputation is critical to
this dynamic. The discussion begins with a brief etymological history
of the concept of reputation and moves to an exploration of how and
why online communication changes our basic nature, our various
selves and the Bakhtin idea of the polyphonic nature of truth. The
discussion considers the damaging effects of bullying and gossip,
both of which constitute an assault on reputation and the latter of
which is not limited to the lifetime of the person. It concludes with
guidelines and specific recommendations.
Abstract: To study the impact of the inter-module ventilation (IMV) on the space station, the Computational Fluid Dynamic (CFD) model under the influence of IMV, the mathematical model, boundary conditions and calculation method are established and determined to analyze the influence of IMV on cabin air flow characteristics and velocity distribution firstly; and then an integrated overall thermal mathematical model of the space station is used to consider the impact of IMV on thermal management. The results show that: the IMV has a significant influence on the cabin air flow, the flowrate of IMV within a certain range can effectively improve the air velocity distribution in cabin, if too much may lead to its deterioration; IMV can affect the heat deployment of the different modules in space station, thus affecting its thermal management, the use of IMV can effectively maintain the temperature levels of the different modules and help the space station to dissipate the waste heat.
Abstract: Water hyacinth has been used in aquatic systems for
wastewater purification in many years worldwide. The role of water
hyacinth (Eichhornia crassipes) species in polishing nitrate and
phosphorus concentration from municipal wastewater treatment plant
effluent by phytoremediation method was evaluated. The objective
of this project is to determine the removal efficiency of water
hyacinth in polishing nitrate and phosphorus, as well as chemical
oxygen demand (COD) and ammonia. Water hyacinth is considered
as the most efficient aquatic plant used in removing vast range of
pollutants such as organic matters, nutrients and heavy metals. Water
hyacinth, also referred as macrophytes, were cultivated in the
treatment house in a reactor tank of approximately 90(L) x 40(W) x
25(H) in dimension and built with three compartments. Three water
hyacinths were placed in each compartments and water sample in
each compartment were collected in every two days. The plant
observation was conducted by weight measurement, plant uptake and
new young shoot development. Water hyacinth effectively removed
approximately 49% of COD, 81% of ammonia, 67% of phosphorus
and 92% of nitrate. It also showed significant growth rate at starting
from day 6 with 0.33 shoot/day and they kept developing up to 0.38
shoot/day at the end of day 24. From the studies conducted, it was
proved that water hyacinth is capable of polishing the effluent of
municipal wastewater which contains undesirable amount of nitrate
and phosphorus concentration.
Abstract: State Dependent Riccati Equation (SDRE) approach is
a modification of the well studied LQR method. It has the capability of being applied to control nonlinear systems. In this paper the technique
has been applied to control the single inverted pendulum (SIP) which represents a rich class of nonlinear underactuated systems. SIP
modeling is based on Euler-Lagrange equations. A procedure is developed
for judicious selection of weighting parameters and constraint handling. The controller designed by SDRE technique here gives better results than existing controllers designed by energy based techniques.
Abstract: In this paper we develop and analyze the model for
the spread of Leptospirosis by age group in Thailand, between 1997
and 2010 by using mathematical modeling and computer simulation.
Leptospirosis is caused by pathogenic spirochetes of the genus
Leptospira. It is a zoonotic disease of global importance and an
emerging health problem in Thailand. In Thailand, leptospirosis is a
reportable disease, the top three age groups are 23.31% in 35-44
years olds group, 22.76% in 25-34 year olds group, 17.60% in 45-54
year olds group from reported leptospirosis between 1997 and 2010,
with a peak in 35-44 year olds group. Our paper, the Leptosipirosis
transmission by age group in Thailand is studied on the mathematical
model. Some analytical and simulation results are presented.
Abstract: A direct downconversion receiver implemented in 0.13 μm 1P8M process is presented. The circuit is formed by a single-end LNA, an active balun for conversion into balanced mode, a quadrature double-balanced passive switch mixer and a quadrature voltage-controlled oscillator. The receiver operates in the 2.4 GHz ISM band and complies with IEEE 802.15.4 (ZigBee) specifications. The circuit exhibits a very low noise figure of only 2.27 dB and dissipates only 14.6 mW with a 1.2 V supply voltage and is hence suitable for low-power applications.
Abstract: Circular tubes have been widely used as structural
members in engineering application. Therefore, its collapse behavior
has been studied for many decades, focusing on its energy absorption
characteristics. In order to predict the collapse behavior of members,
one could rely on the use of finite element codes or experiments.
These tools are helpful and high accuracy but costly and require
extensive running time. Therefore, an approximating model of tubes
collapse mechanism is an alternative for early step of design. This
paper is also aimed to develop a closed-form solution of thin-walled
circular tube subjected to bending. It has extended the Elchalakani et
al.-s model (Int. J. Mech. Sci.2002; 44:1117-1143) to include the
rate of energy dissipation of rolling hinge in the circumferential
direction. The 3-D geometrical collapse mechanism was analyzed by
adding the oblique hinge lines along the longitudinal tube within the
length of plastically deforming zone. The model was based on the
principal of energy rate conservation. Therefore, the rates of internal
energy dissipation were calculated for each hinge lines which are
defined in term of velocity field. Inextensional deformation and
perfect plastic material behavior was assumed in the derivation of
deformation energy rate. The analytical result was compared with
experimental result. The experiment was conducted with a number of
tubes having various D/t ratios. Good agreement between analytical
and experiment was achieved.
Abstract: By analyzing the sources of energy and power
loss in PWM (Pulse Width Modulation) controlled drivers of
water electrolysis cells, it is possible to reduce the power
dissipation and enhance the efficiency of such hydrogen
production units. A PWM controlled power driver is based on
a semiconductor switching element where its power
dissipation might be a remarkable fraction of the total power
demand of an electrolysis system. Power dissipation in a
semiconductor switching element is related to many different
parameters which could be fitted into two main categories:
switching losses and conduction losses. Conduction losses are
directly related to the built, structure and capabilities of a
switching device itself and indeed the conditions in which the
element is handling the switching application such as voltage,
current, temperature and of course the fabrication technology.
On the other hand, switching losses have some other
influencing variables other than the mentioned such as control
system, switching method and power electronics circuitry of
the PWM power driver. By analyzings the characteristics of
recently developed power switching transistors from different
families of Bipolar Junction Transistors (BJT), Metal Oxide
Semiconductor Field Effect Transistors (MOSFET) and
Insulated Gate Bipolar Transistors (IGBT), some
recommendations are made in this paper which are able to
lead to achieve higher hydrogen production efficiency by
utilizing PWM controlled water electrolysis cells.