Abstract: In the transition zone between aquifers and basal aquitards, the perchloroethene (PCE)-pools are more recalcitrant than those elsewhere in the aquifer. Although biodegradation of chloroethenes occur in this zone, it is a slow process and a remediation strategy is needed. The aim of this study is to demonstrate that combined strategy of biostimulation and in situ chemical reduction (ISCR) is more efficient than the two separated strategies. Four different microcosm experiments with sediment and groundwater of a selected field site where an aged pool exists at the bottom of a transition zone were designed under i) natural conditions, ii) biostimulation with lactic acid, iii) ISCR with zero-value iron (ZVI) and under iv) a combined strategy with lactic acid and ZVI. Biotic and abiotic dehalogenation, terminal electron acceptor processes and evolution of microbial communities were determined for each experiment. The main results were: i) reductive dehalogenation of PCE-pools occurs under sulfate-reducing conditions; ii) biostimulation with lactic acid supports more pronounced reductive dehalogenation of PCE and trichloroethene (TCE), but results in an accumulation of 1,2-cis-dichloroethene (cDCE); iii) ISCR with ZVI produces a sustained dehalogenation of PCE and its metabolites iv) combined strategy of biostimulation and ISCR results in a fast dehalogenation of PCE and TCE and a sustained dehalogenation of cisDCE. These findings suggest that biostimulation and ISCR with ZVI are the most suitable strategies for a complete reductive dehalogenation of PCE-pools in the transition zone and further to enable the dissolution of dense non-aqueous phase liquids.
Abstract: Global warming, growing awareness of the environment, waste management issues, dwindling fossil resources, and rising oil prices resulted to increase the research in the materials that are friendly to our health and environment. Due to these reasons, green products are increasingly being promoted for sustainable development. In this work, fully biodegradable green composites have been developed using jute fibers as reinforcement and poly lactic acid as matrix material by film stacking technique. The effect of curing temperature during development of composites ranging from 160 °C, 170 °C, 180 °C and 190 °C was investigated for various mechanical properties. Results obtained from various tests indicate that impact strength decreases with an increase in curing temperature, but tensile and flexural strength increases till 180 °C, thereafter both the properties decrease. This study gives an optimum curing temperature for the development of jute/PLA composites.
Abstract: Due to increasing environmental pressure for biodegradable products, especially in polymeric materials, in order to meet the demands of the biological cycles of the circular economy, new materials have been developed as a sustainability strategy. This study proposes a composite material developed from the biodegradable polymer PLA Ecovio® (polylactic acid - PLA) with natural sisal fibers, where the soybean ester was used as a plasticizer, which can aid in adhesion between the materials and fibers, making the most attractive final composite from an environmental point of view. The composites were obtained by extrusion. The materials tests were produced and submitted to biodegradation tests. Through the biodegradation tests, it can be seen that the biodegradable polymer composition with 5% sisal fiber presented about 12.4% more biodegradability compared to the polymer without fiber addition. It has also been found that the plasticizer was not a compatible with fibers and the polymer. Finally, fibers help to anticipate the decomposition process of the material when subjected to conditions of a landfill. Therefore, its intrinsic properties are not affected during its use, only the biodegradation process begins after its exposure to landfill conditions.
Abstract: The relationship between biodegradation and mechanical behavior is fundamental for studies of the application of cellulose acetate films as a possible material for biodegradable packaging. In this work, the biodegradation of cellulose acetate (CA) with DS 2.5 was analyzed in simulated soil. CA films were prepared by casting and buried in the simulated soil. Samples were taken monthly and analyzed, the total time of biodegradation was 6 months. To characterize the biodegradable CA, the DMA technique was employed. The main result showed that the time of exposure to the simulated soil affects the mechanical properties of the films and the values of crystallinity. By DMA analysis, it was possible to conclude that as the CA is biodegraded, its mechanical properties were altered, for example, storage modulus has increased with biodegradation and the modulus of loss has decreased. Analyzes of DSC, XRD, and FTIR were also carried out to characterize the biodegradation of CA, which corroborated with the results of DMA. The observation of the carbonyl band by FTIR and crystalline indices obtained by XRD were important to evaluate the degradation of CA during the exposure time.
Abstract: Tissue engineering includes combination of materials and techniques used for the improvement, repair or replacement of the tissue. Scaffolds, permanent or temporally material, are used as support for the creation of the "new cell structures". For this important component (scaffold), a variety of materials can be used. The advantage of some polymeric materials is their cytocompatibility and possibility of biodegradation. Poly(L-lactic acid) (PLLA) is a biodegradable, semi-crystalline thermoplastic polymer. PLLA can be fully degraded into H2O and CO2. In this experiment, the effect of the surface modification of biodegradable polymer (performed by plasma treatment) on the various cell types was studied. The surface parameters and changes of the physicochemical properties of modified PLLA substrates were studied by different methods. Surface wettability was determined by goniometry, surface morphology and roughness study were performed with atomic force microscopy and chemical composition was determined using photoelectron spectroscopy. The physicochemical properties were studied in relation to cytocompatibility of human osteoblast (MG 63 cells), rat vascular smooth muscle cells (VSMC), and human stem cells (ASC) of the adipose tissue in vitro. A fluorescence microscopy was chosen to study and compare cell-material interaction. Important parameters of the cytocompatibility like adhesion, proliferation, viability, shape, spreading of the cells were evaluated. It was found that the modification leads to the change of the surface wettability depending on the time of modification. Short time of exposition (10-120 s) can reduce the wettability of the aged samples, exposition longer than 150 s causes to increase of contact angle of the aged PLLA. The surface morphology is significantly influenced by duration of modification, too. The plasma treatment involves the formation of the crystallites, whose number increases with increasing time of modification. On the basis of physicochemical properties evaluation, the cells were cultivated on the selected samples. Cell-material interactions are strongly affected by material chemical structure and surface morphology. It was proved that the plasma treatment of PLLA has a positive effect on the adhesion, spreading, homogeneity of distribution and viability of all cultivated cells. This effect was even more apparent for the VSMCs and ASCs which homogeneously covered almost the whole surface of the substrate after 7 days of cultivation. The viability of these cells was high (more than 98% for VSMCs, 89-96% for ASCs). This experiment is one part of the basic research, which aims to easily create scaffolds for tissue engineering with subsequent use of stem cells and their subsequent "reorientation" towards the bone cells or smooth muscle cells.
Abstract: Poor ability of cartilage tissue when experiencing a damage leads scientists to use tissue engineering as a reliable and effective method for regenerating or replacing damaged tissues. An artificial tissue should have some features such as biocompatibility, biodegradation and, enough mechanical properties like the original tissue. In this work, a composite hydrogel is prepared by using natural and synthetic materials that has high porosity. Mechanical properties of different combinations of polymers such as modulus of elasticity were tested, and a hydrogel with good mechanical properties was selected. Bone marrow derived mesenchymal stem cells were also seeded into the pores of the sponge, and the results showed the adhesion and proliferation of cells within the hydrogel after one month. In comparison with previous works, this study offers a new and efficient procedure for the fabrication of cartilage like tissue and further cartilage repair.
Abstract: The heat and mass transfer characteristics of
contaminants in groundwater subjected to a biodegradation reaction
is analyzed by taking into account the thermal diffusion (Soret)
effects. This phenomenon is modulated mathematically by a
system of partial differential equations which govern the motion
of fluid (groundwater) and solid (contaminants) particles. The
numerical results are presented graphically for different values of
the parameters entering into the problem on the velocity profiles of
fluid, contaminants, temperature and concentration profile.
Abstract: Bendiocarb is a known toxic xenobiotic that presents acute and chronic risks for freshwater invertebrates and estuarine and marine biota; thus, the treatment of water contaminated with the insecticide is of concern. In this paper, a bacterial community with the capacity to grow in bendiocarb as its sole carbon and nitrogen source was isolated by enrichment techniques in batch culture, from samples of a composting plant located in the northeast of Mexico City. Eight cultivable bacteria were isolated from the microbial community, by PCR amplification of 16 rDNA; Pseudoxanthomonas spadix (NC_016147.2, 98%), Ochrobacterium anthropi (NC_009668.1, 97%), Staphylococcus capitis (NZ_CP007601.1, 99%), Bosea thiooxidans. (NZ_LMAR01000067.1, 99%), Pseudomonas denitrificans. (NC_020829.1, 99%), Agromyces sp. (NZ_LMKQ01000001.1, 98%), Bacillus thuringiensis. (NC_022873.1, 97%), Pseudomonas alkylphenolia (NZ_CP009048.1, 98%). NCBI accession numbers and percentage of similarity are indicated in parentheses. These bacteria were regarded as the isolated species for having the best similarity matches. The ability to degrade bendiocarb by the immobilized bacterial community in a packed bed biofilm reactor, using as support volcanic stone fragments (tezontle), was evaluated. The reactor system was operated in batch using mineral salts medium and 30 mg/L of bendiocarb as carbon and nitrogen source. With this system, an overall removal efficiency (ηbend) rounding 90%, was reached.
Abstract: Quick development and usage of nanotechnology have resulted to massive use of various nanoparticles, such as iron oxide nanoparticles (IONPs) and multi-wall carbon nanotubes (MWCNTs). Thus, this study investigated the role of IONPs and MWCNTs in enhancing bioenergy recovery. Results show that IONPs at a concentration of 750 mg/L and MWCNTs at a concentration of 1500 mg/L induced faster substrate utilization and biogas production rates than the control. IONPs exhibited higher carbon oxygen demand (COD) removal efficiency than MWCNTs while on the contrary, MWCNT performance on biogas generation was remarkable than IONPs. Furthermore, scanning electron microscopy (SEM) investigation revealed extracellular polymeric substances (EPS) excretion from AGS had an interaction with nanoparticles. This interaction created a protective barrier to microbial consortia hence reducing their cytotoxicity. Microbial community analyses revealed genus predominance of bacteria of Anaerolineaceae and Longilinea. Their role in biodegradation of the substrate could have highly been boosted by nanoparticles. The archaea predominance of the genus level of Methanosaeta and Methanobacterium enhanced methanation process. The presence of bacteria of genus Geobacter was also reported. Their presence might have significantly contributed to direct interspecies electron transfer in the system. Exposure of AGS to nanoparticles promoted direct interspecies electron transfer among the anaerobic fermenting bacteria and their counterpart methanogens during the anaerobic digestion process. This results provide useful insightful information in understanding the response of microorganisms to IONPs and MWCNTs in the complex natural environment.
Abstract: The environmental fate of organic contaminants in soils is influenced significantly by the pH, texture of soil, water content and also presence of organic matter. In this study, biodegradation of endosulfan isomers was studied in two different soils (Soil A and Soil B) that have contrasting properties in terms of their texture, pH, organic content, etc. Two Nocardia sp., which were isolated from soil, were used for degradation of endosulfan. Soils were contaminated with commercial endosulfan. Six sets were maintained from two different soils, contaminated with different endosulfan concentrations for degradation experiments. Inoculated and uninoculated mineral media with Nocardia isolates were added to the soils and mixed. Soils were incubated at a certain temperature (30 °C) during ten weeks. Residue endosulfan and its metabolites’ concentrations were determined weekly during the incubation period. The changes of the soil microorganisms were investigated weekly.
Abstract: Textile industries cater to varied customer preferences and contribute substantially to the economy. However, these textile industries also produce a considerable amount of effluents. Prominent among these are the azo dyes which impart considerable color and toxicity even at low concentrations. Azo dyes are also used as coloring agents in food and pharmaceutical industry. Despite their applications, azo dyes are also notorious pollutants and carcinogens. Popular techniques like photo-degradation, biodegradation and the use of oxidizing agents are not applicable for all kinds of dyes, as most of them are stable to these techniques. Chemical coagulation produces a large amount of toxic sludge which is undesirable and is also ineffective towards a number of dyes. Most of the azo dyes are stable to UV-visible light irradiation and may even resist aerobic degradation. Adsorption has been the most preferred technique owing to its less cost, high capacity and process efficiency and the possibility of regenerating and recycling the adsorbent. Adsorption is also most preferred because it may produce high quality of the treated effluent and it is able to remove different kinds of dyes. However, the adsorption process is influenced by many variables whose inter-dependence makes it difficult to identify optimum conditions. The variables include stirring speed, temperature, initial concentration and adsorbent dosage. Further, the internal diffusional resistance inside the adsorbent particle leads to slow uptake of the solute within the adsorbent. Hence, it is necessary to identify optimum conditions that lead to high capacity and uptake rate of these pollutants. In this work, commercially available activated carbon was chosen as the adsorbent owing to its high surface area. A typical azo dye found in textile effluent waters, viz. the monoazo Acid Orange 10 dye (CAS: 1936-15-8) has been chosen as the representative pollutant. Adsorption studies were mainly focused at obtaining equilibrium and kinetic data for the batch adsorption process at different process conditions. Studies were conducted at different stirring speed, temperature, adsorbent dosage and initial dye concentration settings. The Full Factorial Design was the chosen statistical design framework for carrying out the experiments and identifying the important factors and their interactions. The optimum conditions identified from the experimental model were validated with actual experiments at the recommended settings. The equilibrium and kinetic data obtained were fitted to different models and the model parameters were estimated. This gives more details about the nature of adsorption taking place. Critical data required to design batch adsorption systems for removal of Acid Orange 10 dye and identification of factors that critically influence the separation efficiency are the key outcomes from this research.
Abstract: In the vicinity of red sea about 15 fungi species were
isolated from oil contaminated sites. On the basis of aptitude to
degrade the crude oil and DCPIP assay, two fungal isolates were
selected amongst 15 oil degrading strains. Analysis of ITS-1, ITS-2
and amplicon pyrosequencing studies of fungal diversity revealed
that these strains belong to Penicillium and Aspergillus species. Two
strains that proved to be the most efficient in degrading crude oil was
Aspergillus niger (54%) and Penicillium commune (48%) Subsequent
to two weeks of cultivation in BHS medium the degradation rate
were recorded by using spectrophotometer and GC-MS. Hence, it is
cleared that these fungal strains has capability of degradation and can
be utilize for cleaning the Saudi Arabian environment.
Abstract: The problem of degradation of agricultural residues
from palm oil industry is increasing due to its expansion.
Lignocelloulosic waste from these industry represent large amount of
unutilized resources, this is due to their high lignin content. Since
white rot fungi are capable of degrading lignin, its potential for the
degradation of lignocelloulosic waste from palm oil industry was
accessed. The lignocellluloses content was measured before and after
biodegradation and the rate of reduction was determined. From the
results of the biodegradation, it was observed that hemicellulose
reduces by 22.62%, cellulose by 20.97% and lignin by 10.65% from
the initials lignocelluloses contents. Thus, to improve the digestibility
of palm oil mesocarp fibre, treatment by white rot-fungi is
recommended.
Abstract: Anammox is a novel and promising technology that has changed the traditional concept of biological nitrogen removal. The process facilitates direct oxidation of ammonical nitrogen under anaerobic conditions with nitrite as an electron acceptor without addition of external carbon sources. The present study investigated the feasibility of Anammox Hybrid Reactor (AHR) combining the dual advantages of suspended and attached growth media for biodegradation of ammonical nitrogen in wastewater. Experimental unit consisted of 4 nos. of 5L capacity AHR inoculated with mixed seed culture containing anoxic and activated sludge (1:1). The process was established by feeding the reactors with synthetic wastewater containing NH4-H and NO2-N in the ratio 1:1 at HRT (hydraulic retention time) of 1 day. The reactors were gradually acclimated to higher ammonium concentration till it attained pseudo steady state removal at a total nitrogen concentration of 1200 mg/l. During this period, the performance of the AHR was monitored at twelve different HRTs varying from 0.25-3.0 d with increasing NLR from 0.4 to 4.8 kg N/m3d. AHR demonstrated significantly higher nitrogen removal (95.1%) at optimal HRT of 1 day. Filter media in AHR contributed an additional 27.2% ammonium removal in addition to 72% reduction in the sludge washout rate. This may be attributed to the functional mechanism of filter media which acts as a mechanical sieve and reduces the sludge washout rate many folds. This enhances the biomass retention capacity of the reactor by 25%, which is the key parameter for successful operation of high rate bioreactors. The effluent nitrate concentration, which is one of the bottlenecks of anammox process was also minimised significantly (42.3-52.3 mg/L). Process kinetics was evaluated using first order and Grau-second order models. The first-order substrate removal rate constant was found as 13.0 d-1. Model validation revealed that Grau second order model was more precise and predicted effluent nitrogen concentration with least error (1.84±10%). A new mathematical model based on mass balance was developed to predict N2 gas in AHR. The mass balance model derived from total nitrogen dictated significantly higher correlation (R2=0.986) and predicted N2 gas with least error of precision (0.12±8.49%). SEM study of biomass indicated the presence of heterogeneous population of cocci and rod shaped bacteria of average diameter varying from 1.2-1.5 mm. Owing to enhanced NRE coupled with meagre production of effluent nitrate and its ability to retain high biomass, AHR proved to be the most competitive reactor configuration for dealing with nitrogen laden wastewater.
Abstract: It is the patient compliance and stability in
combination with controlled drug delivery and biocompatibility that
forms the core feature in present research and development of
sustained biodegradable patch formulation intended for wound
healing. The aim was to impart sustained degradation, sterile
formulation, significant folding endurance, elasticity,
biodegradability, bio-acceptability and strength. The optimized
formulation comprised of polymers including Hydroxypropyl methyl
cellulose, Ethylcellulose, and Gelatin, and Citric Acid PEG Citric
acid (CPEGC) triblock dendrimers and active Curcumin. Polymeric
mixture dissolved in geometric order in suitable medium through
continuous stirring under ambient conditions. With continued stirring
Curcumin was added with aid of DCM and Methanol in optimized
ratio to get homogenous dispersion. The dispersion was sonicated
with optimum frequency and for given time and later casted to form a
patch form. All steps were carried out under strict aseptic conditions.
The formulations obtained in the acceptable working range were
decided based on thickness, uniformity of drug content, smooth
texture and flexibility and brittleness. The patch kept on stability
using butter paper in sterile pack displayed folding endurance in
range of 20 to 23 times without any evidence of crack in an
optimized formulation at room temperature (RT) (24 ± 2°C). The
patch displayed acceptable parameters after stability study conducted
in refrigerated conditions (8±0.2°C) and at RT (24 ± 2°C) up to 90
days. Further, no significant changes were observed in critical
parameters such as elasticity, biodegradability, drug release and drug
content during stability study conducted at RT 24±2°C for 45 and 90
days. The drug content was in range 95 to 102%, moisture content
didn’t exceeded 19.2% and patch passed the content uniformity test.
Percentage cumulative drug release was found to be 80% in 12h and
matched the biodegradation rate as drug release with correlation
factor R2>0.9. The biodegradable patch based formulation developed
shows promising results in terms of stability and release profiles.
Abstract: The disposal and the treatment of sewage sludge is an
expensive and environmentally complex problem. In this work, a
lipopeptide biosurfactant extracted from corn steep liquor was used
as ecofriendly and cost-competitive alternative for the mobilization
and bioremediation of fluorene in sewage sludge. Results have
demonstrated that this biosurfactant has the capability to mobilize
fluorene to the aqueous phase, reducing the amount of fluorene in the
sewage sludge from 484.4 mg/Kg up to 413.7 mg/Kg and 196.0
mg/Kg after 1 and 27 days respectively. Furthermore, once the
fluorene was extracted the lipopeptide biosurfactant contained in the
aqueous phase allowed the biodegradation, up to 40.5% of the initial
concentration of this polycyclic aromatic hydrocarbon.
Abstract: Fungal mutant strains have produced cellulase and
xylanase enzymes, and have induced high hydrolysis with enhanced
of rice straw. The mutants were obtained by exposing Penicillium
strain to UV-light treatments. Screening and selection after treatment
with UV-light were carried out using cellulolytic and xylanolytic
clear zones method to select the hypercellulolytic and
hyperxylanolytic mutants. These mutants were evaluated for their
cellulase and xylanase enzyme production as well as their abilities for
biodegradation of rice straw. The mutant 12 UV/1 produced 306.21%
and 209.91% cellulase and xylanase, respectively, as compared with
the original wild type strain. This mutant showed high capacity of
rice straw degradation. The effectiveness of tested mutant strain and
that of wild strain was compared in relation to enhancing the
composting process of rice straw and animal manures mixture. The
results obtained showed that the compost product of inoculated
mixture with mutant strain (12 UV/1) was the best compared to the
wild strain and un-inoculated mixture. Analysis of the composted
materials showed that the characteristics of the produced compost
were close to those of the high quality standard compost. The results
obtained in the present work suggest that the combination between
rice straw and animal manure could be used for enhancing the
composting process of rice straw and particularly when applied with
fungal decomposer accelerating the composting process.
Abstract: Bacterial strains capable of degradation of malathion
from the domestic sewage were isolated by an enrichment culture
technique. Three bacterial strains were screened and identified as
Acinetobacter baumannii (AFA), Pseudomonas aeruginosa (PS1),
and Pseudomonas mendocina (PS2) based on morphological,
biochemical identification and 16S rRNA sequence analysis.
Acinetobacter baumannii AFA was the most efficient malathion
degrading bacterium, so used for further biodegradation study. AFA
was able to grow in mineral salt medium (MSM) supplemented with
malathion (100 mg/l) as a sole carbon source, and within 14 days,
84% of the initial dose was degraded by the isolate measured by high
performance liquid chromatography. Strain AFA could also degrade
other organophosphorus compounds including diazinon, chlorpyrifos
and fenitrothion. The effect of different culture conditions on the
degradation of malathion like inoculum density, other carbon or
nitrogen sources, temperature and shaking were examined.
Degradation of malathion and bacterial cell growth were accelerated
when culture media were supplemented with yeast extract, glucose
and citrate. The optimum conditions for malathion degradation by
strain AFA were; an inoculum density of 1.5x 10^12CFU/ml at 30°C
with shaking. A specific polymerase chain reaction primers were
designed manually using multiple sequence alignment of the
corresponding carboxylesterase enzymes of Acinetobacter species.
Sequencing result of amplified PCR product and phylogenetic
analysis showed low degree of homology with the other
carboxylesterase enzymes of Acinetobacter strains, so we suggested
that this enzyme is a novel esterase enzyme. Isolated bacterial strains
may have potential role for use in bioremediation of malathion
contaminated.
Abstract: The present study was conducted to evaluate the
potential applicability of biological trickling filter system for the
treatment of simulated textile wastewater containing reactive azo
dyes with bacterial consortium under non-sterile conditions. The
percentage decolorization for the treatment of wastewater containing
structurally different dyes was found to be higher than 95% in all
trials. The stable bacterial count of the biofilm on stone media of the
trickling filter during the treatment confirmed the presence,
proliferation, dominance and involvement of the added microbial
consortium in the treatment of textile wastewater. Results of
physicochemical parameters revealed the reduction in chemical
oxygen demand (58.5-75.1%), sulphates (18.9-36.5%), and
phosphates (63.6-73.0%). UV-Visible and FTIR spectroscopy
confirmed decolorization of dye containing wastewater was ultimate
consequence of biodegradation. Toxicological studies revealed the
nontoxic nature of degradative metabolites.
Abstract: In the present study, presence of endosulfan, imidacloprid, carbendazim, in the soil /vegetables/cereals and water samples was observed in agriculture fields of Uttarakhand. In view of biodegradation of these pesticides, 9 bacterial isolates were recovered from the soil samples of the fields which tolerated endosulfan, imidacloprid, carbendazim from 100 to 200 µg/ml. Three bacterial consortia used for in vitro bioremediation experiments were consisted of 3 bacterial isolates for carbendazim, imidacloprid and endosulfan, respectively. Maximum degradation (87 and 83%) of α and β endosulfan respectively was observed in soil slurry by consortium. Degradation of Imidacloprid and carbendazim under similar conditions was 88.4 and 77.5% respectively. FT-IR analysis of biodegraded samples of pesticides in liquid media showed stretching of various bonds. GC-MS of biodegraded endosulfan sample in soil slurry showed the presence of nontoxic intermediates. A pot trial with Bacterial treatments lowered down the uptake of pesticides in onion plants.