Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: Machining parameters are very important in
determining the surface quality of any material. In the past decade,
some new engineering materials were developed for the
manufacturing industry which created a need to conduct an
investigation on the impact of the said parameters on their surface
roughness. Polyurethane (PU) block is widely used in the automotive
industry to manufacture parts such as checking fixtures that are used
to verify the dimensional accuracy of automotive parts. In this paper,
the design of experiment (DOE) was used to investigate on the effect
of the milling parameters on the PU block. Furthermore, an analysis
of the machined surface chemical composition was done using
scanning electron microscope (SEM). It was found that the surface
roughness of the PU block is severely affected when PU undergoes a
flood machining process instead of a dry condition. In addition the
stepover and the silicon content were found to be the most significant
parameters that influence the surface quality of the PU block.
Abstract: Heavy rare earth (HRE) oxalate concentrates were
prepared from the Egyptian crude monazite sand (graded about 47%).
The concentrates were specified quantitatively for their constituents
of individual rare earth elements using ion chromatograph (IC) and
qualitatively by scanning electron microscope (SEM) for the other
major constituents. The 1st concentrate was composed of 10.5%
HREE where 7.25% of them represented yttrium. The 2nd concentrate
contained about 41.7% LREE, 17.5% HREE and 13.6% Th. The
LREE involved 18.3% Ce, 10.5% La and 8% Nd while the HREE
were 8.7% Y, 3.5% Gd and 2.9% Dy. The 3rd concentrate was
containing about 8.0% LREE (3.7% Ce, 2.0% La and 1.5% Nd),
10.2% HREE (6.4% yttrium and 2.0% Dy) and 2.1% uranium. The
final concentrate comprised 0.84% uranium beside iron, chromium
and traces of REE.
Abstract: In the present study, we have synthesized Cr and Fe
doped zinc oxide (ZnO) nanostructures (Zn1-δCraFebO; where δ = a +
b = 20%, a = 5, 6, 8 & 10% and b = 15, 14, 12 & 10%) via sol-gel
method at different doping concentrations. The synthesized samples
were characterized for structural properties by X-ray diffractrometer
and field emission scanning electron microscope and the optical
properties were carried out through photoluminescence and UVvisible
spectroscopy. The particle size calculated through field
emission scanning electron microscope varies from 41 to 96 nm for
the samples synthesized at different doping concentrations. The
optical band gaps calculated through UV-visible spectroscopy are
found to be decreasing from 3.27 to 3.02 eV as the doping
concentration of Cr increases and Fe decreases.
Abstract: This research aims to investigate callus induction,
somatic embryogenesis and indirect plant regeneration of Crassula
ovata (Mill.) Druce – the famous ornamental plant. Experiment no.1:
Callus induction was obtained from leaf and stem explants on
Murashige and Skoog (MS) medium supplemented with various plant
growth regulators (PGRs). Effects of different PGRs, plant
regeneration and subsequent plantlet conversion were also assessed.
Indirect plant regeneration was achieved from the callus of stem
explants by the addition of 1.5 mg/L Kinetin (KN) alone. Best shoot
induction was achieved (6.5 shoots/per explant) after 60 days. For
successful rooting, regenerated plantlets were sub-cultured on the
same MS media supplemented with 1.5 mg/L KN alone. The rooted
plantlets were acclimatized and the survival rate was 90%.
Experiment no.2: Results revealed that 0.5 mg/L 2,4-D alone and in
combination with 1.0 mg/L 6-Benzyladenine (BA) gave 89.8% callus
from the stem explants as compared to leaf explants. Callus
proliferation and somatic embryo formation were also evaluated by
‘Double Staining Method’ and different stages of somatic
embryogenesis were revealed by scanning electron microscope. Full
Strength MS medium produced the highest number (49.6%) of
cotyledonary stage somatic embryos (SEs). Mature cotyledonary
stage SEs developed into plantlets after 12 weeks of culture. Wellrooted
plantlets were successfully acclimatized at the survival rate of
85%. Indirectly regenerated plants did not show any detectable
variation in morphological and growth characteristics when
compared with the donor plant.
Abstract: Fly ash is an important waste, produced in thermal
power plants which causes very important environmental pollutions.
For this reason the usage and evaluation the fly ash in various areas
are very important. Nearly, 15 million tons/year of fly ash is
produced in Turkey. In this study, usage of fly ash with diatomite and
molasses for heavy metal (Cd) adsorption from wastewater is
investigated. The samples of Seyitomer region fly ash were analyzed
by X-ray fluorescence (XRF) and Scanning Electron Microscope
(SEM) then diatomite (0 and 1% in terms of fly ash, w/w) and
molasses (0-0.75 mL) were pelletized under 30 MPa of pressure for
the usage of cadmium (Cd) adsorption in wastewater. After the
adsorption process, samples of Seyitomer were analyzed using
Optical Emission Spectroscopy (ICP-OES). As a result, it is seen that
the usage of Seyitomer fly ash is proper for cadmium (Cd) adsorption
and an optimum adsorption yield with 52% is found at a compound
with Seyitomer fly ash (10 g), diatomite (0.5 g) and molasses (0.75
mL) at 2.5 h of reaction time, pH:4, 20ºC of reaction temperature and
300 rpm of stirring rate.
Abstract: In this study, Electrical Discharge Machining (EDM) is used to modify the surface of high carbon steel En31 with the help of tool electrode (Copper-Chromium-Nickel) manufactured by powder metallurgy (PM) process. The effect of EDM on surface roughness during surface alloying is studied. Taguchi’s Design of experiment (DOE) and L18 orthogonal array is used to find the best level of input parameters in order to achieve high surface finish. Six input parameters are considered and their percentage contribution towards surface roughness is investigated by analysis of variances (ANOVA). Experimental results show that an hard alloyed surface (1.21% carbon, 2.14% chromium and 1.38% nickel) with surface roughness of 3.19µm can be generated using EDM with PM tool. Additionally, techniques like Scanning Electron Microscope (SEM) and Energy Dispersive Spectroscopy (EDS) are used to analyze the machined surface and EDMed layer composition, respectively. The increase in machined surface micro-hardness (101%) may be related to the formation of carbides containing chromium.
Abstract: In this study, fish bone waste was used as a new
catalyst for biodiesel production. Instead of discarding the fish bone
waste, it will be utilized as a source for catalyst that can provide
significant benefit to the environment. Also, it can be substitute as a
calcium oxide source instead of using eggshell, crab shell and snail
shell. The XRD and SEM analysis proved that calcined fish bone
contains calcium oxide, calcium phosphate and hydroxyapatite. The
catalyst was characterized using Scanning Electron Microscope
(SEM) and X-ray Diffraction (XRD).
Abstract: Many studies have been conducted on DC transmission. Of power apparatus for DC transmission, high voltage direct current (HVDC) cable systems are being evaluated because of the increase in power demand and transmission distance. Therefore, dc insulation characteristics of liquid silicone rubber (LSR), which has various advantages such as short curing time and the ease of maintenance, were investigated to assess its performance as a HVDC insulation material for cable joints. The electrical performance of LSR added to nano-aluminum trihydrate (ATH) were confirmed by measurements of the breakdown strength and electrical conductivity. In addition, field emission scanning electron microscope (FE-SEM) was used as a means of confirmation of nanofiller dispersion state. The LSR nanocomposite was prepared by compounding LSR filled nano-sized ATH filler. The dc insulation properties of LSR added to nano-sized ATH fillers were found to be superior to those of the LSR without a filler.
Abstract: Al/Cu clad sheet has been fabricated by using differential speed rolling (DSR) process, which caused severe shear deformation between Al and Cu plate to easily bond to each other. Rolling was carried out at 100 and 150oC with speed ratios from 1.4 to 2.2, in which the total thickness reduction was in the range between 14 and 46%. Interfacial microstructure and mechanical properties of Al/Cu clad were investigated by scanning electron microscope equipped with energy dispersive X-ray detector, and tension tests. The DSR process was very effective to provide a good interface for atoms diffusion during subsequent annealing. The strength of bonding was higher with the increasing speed ratio. Post heat treatment enhanced the mechanical properties of clad sheet by forming intermetallic compounds in the interface area.
Abstract: In the present study, two TRIP-assisted steels were designated as A (having no Cr and Cu content) and B (having higher Ni, Cr and Cu content) heat treated under different conditions, and the correlation between its heat treatment, microstructure and properties were investigated. Micro structural examination was carried out by optical microscope and scanning electron microscope after electrolytic etching. Non-destructive electrochemical and ultrasonic testing on two TRIP-assisted steels was used to find out corrosion and mechanical properties of different alter microstructure phase’s steels. Furthermore, micro structural studies accompanied by the evaluation of mechanical properties revealed that steels having martensite phases with higher corrosive and hardness value were less sound velocity and also steel’s microstructure having finer grains that was more grain boundary was less corrosion resistance. Steel containing more Cu, Ni and Cr was less corrosive compared to other steels having same processing or microstructure.
Abstract: Characteristics of MSM photodetector based on a porous In0.08Ga0.92N thin film were reported. Nanoporous structures of n-type In0.08Ga0.92N/AlN/Si thin films were synthesized by photoelectrochemical (PEC) etching at a ratio of 1:4 of HF:C2H5OH solution for 15min. The structural and optical properties of pre- and post-etched thin films were investigated. Field emission scanning electron microscope and atomic force microscope images showed that the pre-etched thin film has a sufficiently smooth surface over a large region and the roughness increased for porous film. Blue shift has been observed in photoluminescence emission peak at 300 K for porous sample. The photoluminescence intensity of the porous film indicated that the optical properties have been enhanced. A high work function metals (Pt and Ni) were deposited as a metal contact on the porous films. The rise and recovery times of the devices were investigated at 390nm chopped light. Finally, the sensitivity and quantum efficiency were also studied.
Abstract: In this study, the phase transition characteristics of flame-synthesized γ-Al2O3 nanoparticles to α-Al2O3 have been investigated. The nanoparticles were synthesized by using a coflow hydrogen diffusion flame. The phase transition and particle characteristics of the Al2O3 nanoparticles were determined by examining the crystalline structure and the shape of the collected nanoparticles before and after the heat treatment. The morphology and crystal structure of the Al2O3 nanoparticles were determined from SEM images and XRD analyses, respectively. The measured specific surface area and averaged particle size were 63.44m2/g and 23.94nm, respectively. Based on the scanning electron microscope images and x-ray diffraction patterns, it is believed that the onset temperature of the phase transition to α-Al2O3 was existed near 1200oC. The averaged diameters of the sintered particles heat treated at 1,260oC were approximately 80nm.
Abstract: This study was conducted to formulate diclofenac sodium-loaded chitosan nanoparticles and to study the effect of formulation compositions on particle size and zeta potential of chitosan nanoparticles (CSN) containing diclofenac sodium (DC) prepared by ionotropic gelation method. It was found that the formulations containing chitosan, DC and tripolyphosphate (TPP) at a weight ratio of 4:1:1, respectively, with various pH provided various systems. At pH 5.0 and 6.0, the obtained systems were turbid because of precipitation of DC and chitosan, respectively. However, the dispersed system of CSN possessing diameter of 108±1 nm and zeta potential of 19±1 mV could be obtained at pH 5.5. These CSN also showed spherical morphology observed via a transmission scanning electron microscope. Change in weight ratio of chitosan:DC:TPP i.e. 1:1:1, 2:1:1, 3:1:1 and 4:1:1 showed that these ratios led to precipitation of particles except for the ratio of 4:1:1 providing CSN properly. The effect of Tween 80 as a stabilizer was also determined. It suggested that increment of Tween 80 concentration to 0.02% w/v could stabilize CSN at least 48 hours. However, increment of Tween 80 to 0.03% w/v led to quick precipitation of particles. The study of effect of TPP suggested that increment of TPP concentration increased particle size but decreased zeta potential. The excess TPP caused precipitation of CSN. Therefore, the optimized CSN was the CSN containing chitosan, DC and TPP at the ratio of 4:1:1and 0.02% w/v Tween 80 prepared at pH 5.5. Their particle size, zeta potential and entrapment efficiency were 128±1 nm, 15±1 mV and 45.8±2.6%, respectively.
Abstract: According to synthetic plastics obtained from petroleum cause some environmental problems. Therefore, degradable plastics become widely used and studied for replacing the synthetic plastic waste. A biopolymer of poly hydroxybutyrate-co-hydroxyvalerate (PHBV) is subgroups of a main kind of polyhydroxyalkanoates (PHAs). Naturally, PHBV is hard, brittle and low flexible while natural rubber (NR) is high elastic latex. Then, they are blended and the biodegradation of the blended PHBV and NR films were examined in soil environment. The results showed that the degradation occurs predominantly in the bulk of the samples. The order of biodegradability was shown as follows: PHBV> PHBV/NR> NR. After biodegradation, the blended films were characterized by appearance analysis such as Scanning Electron Microscope (SEM), Fourier transform infrared spectroscopy (FTIR) and Differential Scanning Calorimetry (DSC). It was found that the biodegradation mainly occurred at the polymer surface.
Abstract: Aluminum/Copper clad sheet has been fabricated using
asymmetric extrusion method, which caused severe shear deformation
between Al and Cu plate to easily bond to each other. Interfacial
microstructure and mechanical properties of Al/Cu clad were studied
by scanning electron microscope equipped with energy dispersive
X-ray detector, micro-hardness, and tension tests. The asymmetric
extrusion bonding was very effective to provide a good interface for
atoms diffusion during subsequent annealing. The strength of bonding
was higher with the increasing extrusion ratio.
Abstract: In this article, biomechanical aspects of hen-s eggshell as a natural ceramic structure are studied. The images, taken by a scanning electron microscope (SEM), are used to investigate the microscopic aspects of the egg. It is observed that eggshell has a three-layered microstructure with different morphological and structural characteristics. Studies on the eggshell membrane (ESM) as a prosperous tissue suggest that it is placed to prevent the penetration of microorganisms into the egg. Finally, numerical models of the egg are presented to study the stress distribution and its deformation under different loading conditions. The effects of two different types of loading (hydrostatic and point loadings) on two different shell models (with constant and variable thicknesses) are investigated in detail.
Abstract: The morphology, mineralogical and chemical
composition of a low-grade nickel ore from Mpumalanga, South
Africa, were studied by scanning electron microscope (SEM), X-ray
diffraction (XRD) and X-ray fluorescence (XRF), respectively. The
ore was subjected to atmospheric agitation leaching using sulphuric
acid to investigate the effects of acid concentration, leaching
temperature, leaching time and particle size on extraction of nickel
and cobalt. Analyses results indicated the ore to be a saprolitic nickel
laterite belonging to the serpentine group of minerals. Sulphuric acid
was found to be able to extract nickel from the ore. Increased acid
concentration and temperature only produced low amounts of nickel
but improved cobalt extraction. As high as 77.44% Ni was achieved
when leaching a -106+75μm fraction with 4.0M acid concentration at
25oC. The kinetics of nickel leaching from the saprolitic ore were
studied and the activation energy was determined to be 18.16kJ/mol.
This indicated that nickel leaching reaction was diffusion controlled.
Abstract: Noble metal participation in nanostructured
semiconductor catalysts has drawn much interest because of their
improved properties. Recently, it has been discussed by many
researchers that Ag participation in TiO2, CuO, ZnO semiconductors
showed improved photocatalytic and optical properties. In this
research, Ag/ZnO nanocomposite particles were prepared by
Ultrasonic Spray Pyrolysis(USP) Method. 0.1M silver and zinc
nitrate aqueous solutions were used as precursor solutions. The
Ag:Zn atomic ratio of the solution was selected 1:1. Experiments
were taken place under constant air flow of 400 mL/min at 800°C
furnace temperature. Particles were characterized by X-Ray
Diffraction (XRD), Scanning Electron Microscope (SEM) and
Energy Dispersive Spectroscopy (EDS). The crystallite sizes of Ag
and ZnO in composite particles are 24.6 nm, 19.7 nm respectively.
Although, spherical nanocomposite particles are in a range of 300-
800 nm, these particles are formed by the aggregation of primary
particles which are in a range of 20-60 nm.
Abstract: Charging and discharging phenomenon on the surface
of materials can be found in plasma display panel, spacecraft
charging, high voltage insulator, etc. This report gives a simple
explanation on this phenomenon. A scanning electron microscope
was used not only as a tool to produce energetic electron beam to
charge an insulator without metallic coating and to produce a surface
discharging (surface breakdown/flashover) but also to observe the
visible charging and discharging on the sample surface. A model of
electric field distribution on the surface was developed in order to
explain charging and discharging phenomena. Since charging and
discharging process involves incubation time, therefore this process
can be used to evaluate the insulation property of materials under
electron bombardment.