Abstract: Usually, phosphate deposits contain 238U and 232Th in addition to their decay products. Due to their different pathways in the environment, the 238U/232Th activity concentration ratio usually found to be greater than unity in phosphate sediments. The presence of these radionuclides creates a potential need to control exposure of workers in the mining and processing activities of the phosphate minerals in accordance with IAEA safety standards. The greatest dose to workers comes from exposure to radon, especially 222Rn from the uranium series, and has to be controlled. In this regard, radon (222Rn) was measured in the atmosphere (indoor and outdoor) of Al-Jalamid phosphate-mines working area using a portable radon-measurement instrument RAD7, in a purpose of radiation protection. Radon was measured in 61 sites inside the open phosphate mines, the phosphate upgrading facility (offices and rooms of the workers, and in some open-air sites) and in the dwellings of the workers residence-village that lies at about 3 km from the mines working area. The obtained results indicated that the average indoor radon concentration was about 48.4 Bq/m3. Inside the upgrading facility, the average outdoor concentrations were 10.8 and 9.7 Bq/m3 in the concentrate piles and crushing areas, respectively. It was 12.3 Bq/m3 in the atmosphere of the open mines. These values are comparable with the global average values. Based on the average values, the annual effective dose due to radon inhalation was calculated and risk estimates have been done. The average annual effective dose to workers due to the radon inhalation was estimated by 1.32 mSv. The potential excess risk of lung cancer mortality that could be attributed to radon, when considering the lifetime exposure, was estimated by 53.0x10-4. The results have been discussed in detail.
Abstract: Environment free of pollutants should be the concern of every individual but with industrialization and urbanization it is difficult to achieve. In view of achieving a pollution limited environment at low cost, a study was conducted on the use of bioremediation technology to remediate hydrocarbons and three heavy metals namely; copper (Cu), zinc (Zn) and iron (Fe) from a typical petroleum refinery wastewater in a closed system. Physicochemical and microbiological characteristics on the wastewater sample revealed that it was polluted with the aforementioned pollutants. Isolation and identification of microorganisms present in the wastewater sample revealed the presence of Bacillus subtilis, Micrococcus luteus, Staphylococcus aureus and Staphylococcus epidermidis. Bioremediation experiments carried out on five batch reactors with different compositions but at same environmental conditions revealed that treatment T5 (boosted with the association of Bacillus subtilis, Micrococcus luteus) gave the best result in terms of oil and grease content removal (i.e. 67% in 63 days). In addition, these microorganisms were able of reducing the concentrations of heavy metals in the sample. Treatments T5, T3 (boosted with Bacillus subtilis only) and T4 (boosted with Micrococcus luteus only) gave optimum percentage uptakes of 65, 75 and 25 for Cu, Zn and Fe respectively.
Abstract: This research aims to investigate callus induction,
somatic embryogenesis and indirect plant regeneration of Crassula
ovata (Mill.) Druce – the famous ornamental plant. Experiment no.1:
Callus induction was obtained from leaf and stem explants on
Murashige and Skoog (MS) medium supplemented with various plant
growth regulators (PGRs). Effects of different PGRs, plant
regeneration and subsequent plantlet conversion were also assessed.
Indirect plant regeneration was achieved from the callus of stem
explants by the addition of 1.5 mg/L Kinetin (KN) alone. Best shoot
induction was achieved (6.5 shoots/per explant) after 60 days. For
successful rooting, regenerated plantlets were sub-cultured on the
same MS media supplemented with 1.5 mg/L KN alone. The rooted
plantlets were acclimatized and the survival rate was 90%.
Experiment no.2: Results revealed that 0.5 mg/L 2,4-D alone and in
combination with 1.0 mg/L 6-Benzyladenine (BA) gave 89.8% callus
from the stem explants as compared to leaf explants. Callus
proliferation and somatic embryo formation were also evaluated by
‘Double Staining Method’ and different stages of somatic
embryogenesis were revealed by scanning electron microscope. Full
Strength MS medium produced the highest number (49.6%) of
cotyledonary stage somatic embryos (SEs). Mature cotyledonary
stage SEs developed into plantlets after 12 weeks of culture. Wellrooted
plantlets were successfully acclimatized at the survival rate of
85%. Indirectly regenerated plants did not show any detectable
variation in morphological and growth characteristics when
compared with the donor plant.
Abstract: Some of the major concerns regarding sewer overflows to receiving water bodies include serious environmental, aesthetic and public health problems. A noble self-cleansing sewer overflow screening device having a sewer overflow chamber, a rectangular tank and a slotted ogee weir to capture the gross pollutants has been investigated. Computational Fluid Dynamics (CFD) techniques are used to simulate the flow phenomena with two different inlet orientations; parallel and perpendicular to the weir direction. CFD simulation results are compared with analytical results. Numerical results show that the flow is not uniform (across the width of the inclined surface) near the top of the inclined surface. The flow becomes uniform near the bottom of the inclined surface, with significant increase of shear stress. The simulation results promises for an effective and efficient self-cleansing sewer overflow screening device by comparing hydrodynamic results.
Abstract: Sometimes the amount of time available for testing could be considerably less than the expected lifetime of the component. To overcome such a problem, there is the accelerated life-testing alternative aimed at forcing components to fail by testing them at much higher-than-intended application conditions. These models are known as acceleration models. One possible way to translate test results obtained under accelerated conditions to normal using conditions could be through the application of the “Maxwell Distribution Law.” In this paper we will apply a combined approach of a sequential life testing and an accelerated life testing to a low alloy high-strength steel component used in the construction of overpasses in Brazil. The underlying sampling distribution will be three-parameter Inverse Weibull model. To estimate the three parameters of the Inverse Weibull model we will use a maximum likelihood approach for censored failure data. We will be assuming a linear acceleration condition. To evaluate the accuracy (significance) of the parameter values obtained under normal conditions for the underlying Inverse Weibull model we will apply to the expected normal failure times a sequential life testing using a truncation mechanism. An example will illustrate the application of this procedure.
Abstract: In this paper we will develop a sequential life test approach applied to a modified low alloy-high strength steel part used in highway overpasses in Brazil.We will consider two possible underlying sampling distributions: the Normal and theInverse Weibull models. The minimum life will be considered equal to zero. We will use the two underlying models to analyze a fatigue life test situation, comparing the results obtained from both.Since a major chemical component of this low alloy-high strength steel part has been changed, there is little information available about the possible values that the parameters of the corresponding Normal and Inverse Weibull underlying sampling distributions could have. To estimate the shape and the scale parameters of these two sampling models we will use a maximum likelihood approach for censored failure data. We will also develop a truncation mechanism for the Inverse Weibull and Normal models. We will provide rules to truncate a sequential life testing situation making one of the two possible decisions at the moment of truncation; that is, accept or reject the null hypothesis H0. An example will develop the proposed truncated sequential life testing approach for the Inverse Weibull and Normal models.
Abstract: The main objective of this work is to compare the
quality of service of the bus companies operating in the city of Rio
Branco, located in the state of Acre with the quality of service of the
bus companies operating in the city of Campos, situated in the state
of Rio de Janeiro, both cities in Brazil. This comparison, based on the
opinion of the bus users, will determine their degree of satisfaction
with the service available in both cities. The outcome of this
evaluation shows the users unhappy with the quality of the service
provided by the bus companies operating in both cities and the need
to identify alternative solutions that may minimize the consequences
caused by the main problems detected in this work. With these
alternatives available, the bus companies will be able to better
understand the needs of their customers in terms of manpower,
service cost, time schedule, etc.
Abstract: The State of Rio de Janeiro, Brazil, will hold two important events in the nearby future. In 2014 it will have the final game of the Football World Cup, and in 2016 it will be holding the Olympic Games. Therefore, the public transportation system (mainly buses) is of a major concern to the Rio de Janeiro State authorities-. The main objective of this work is to compare the quality of service of the bus companies operating in the cities of ItaperunaandCampos, both cities situated in the state of Rio de Janeiro, Brazil. The outcome of thiscomparison, based on the opinion of the bus users, has shownthemdispleased with the quality of the service provided by the bus companies operating in both cities. It is urgent the need to find possible practical alternatives to minimize the consequences of the main problems detected in this work. With these practical alternatives available, we will be able to offer to the Rio de Janeiro State authorities- suggestions about possible solutions to the main problems identified in this survey, as well as the time of implantation and costs of these solutions.
Abstract: In this paper the main objective is to analyze the
quality of service of the bus companies operating in the city of
Campos, located in the state of Rio de Janeiro, Brazil. This analysis,
based on the opinion of the bus customers, will help to determine
their degree of satisfaction with the service provided by the bus
companies. The result of this assessment shows that the bus
customers are displeased with the quality of service supplied by the
bus companies. Therefore, it is necessary to identify alternative
solutions to minimize the consequences of the main problems related
to customers- dissatisfaction identified in our evaluation and to help
the bus companies operating in Campos better fulfill their riders-
needs.
Abstract: In this paper we will develop further the sequential life test approach presented in a previous article by [1] using an underlying two parameter Inverse Weibull sampling distribution. The location parameter or minimum life will be considered equal to zero. Once again we will provide rules for making one of the three possible decisions as each observation becomes available; that is: accept the null hypothesis H0; reject the null hypothesis H0; or obtain additional information by making another observation. The product being analyzed is a new electronic component. There is little information available about the possible values the parameters of the corresponding Inverse Weibull underlying sampling distribution could have.To estimate the shape and the scale parameters of the underlying Inverse Weibull model we will use a maximum likelihood approach for censored failure data. A new example will further develop the proposed sequential life testing approach.
Abstract: In this paper, the test purpose will be to assess
whether or not the accelerated model proposed by Eyring will be able
to translate results for the shape and scale parameters of an
underlying Weibull model, obtained under two accelerating using
conditions, to expected normal using condition results for these
parameters. The product being analyzed is a new type of insulate
fluid, and the accelerating factor is the voltage stresses applied to the
fluid at two different levels (30KV and 40KV). The normal operating
voltage is 25KV. In this case, it was possible to test the insulate fluid
at normal voltage using condition. Both results for the two
parameters of the Weibull model, obtained under normal using
condition and translated from accelerated using conditions to normal
conditions, will be compared to each other to assess the accuracy of
the Eyring model when the accelerating factor is only the voltage
stress.
Abstract: In this paper we will develop further the sequential
life test approach presented in a previous article by [1] using an
underlying two parameter Weibull sampling distribution. The
minimum life will be considered equal to zero. We will again provide
rules for making one of the three possible decisions as each
observation becomes available; that is: accept the null hypothesis H0;
reject the null hypothesis H0; or obtain additional information by
making another observation. The product being analyzed is a new
type of a low alloy-high strength steel product. To estimate the shape
and the scale parameters of the underlying Weibull model we will use
a maximum likelihood approach for censored failure data. A new
example will further develop the proposed sequential life testing
approach.