Abstract: The effect of SnO2 surface modification by Ag nanoclusters, synthesized by SILD method, on the operating characteristics of thin film gas sensors was studied and models for the promotional role of Ag additives were discussed. It was found that mentioned above approach can be used for improvement both the sensitivity and the rate of response of the SnO2-based gas sensors to CO and H2. At the same time, the presence of the Ag clusters on the surface of SnO2 depressed the sensor response to ozone.
Abstract: Engineered nanoparticles’ usage rapidly increased in
various applications in the last decade due to their unusual properties.
However, there is an ever increasing concern to understand their
toxicological effect in human health. Particularly, metal and metal
oxide nanoparticles have been used in various sectors including
biomedical, food and agriculture. But their impact on human health is
yet to be fully understood. In this present investigation, we assessed
the toxic effect of engineered nanoparticles (ENPs) including Ag,
MgO and Co3O4 nanoparticles (NPs) on human mesenchymal stem
cells (hMSC) adopting cell viability and cellular morphological
changes as tools The results suggested that silver NPs are more toxic
than MgO and Co3O4NPs. The ENPs induced cytotoxicity and
nuclear morphological changes in hMSC depending on dose. The cell
viability decreases with increase in concentration of ENPs. The
cellular morphology studies revealed that ENPs damaged the cells.
These preliminary findings have implications for the use of these
nanoparticles in food industry with systematic regulations.
Abstract: An aqueous methanol sensor for use in direct
methanol fuel cells (DMFCs) applications is demonstrated; the
methanol sensor is built using dispersed single-walled carbon
nanotubes (SWCNTs) with Nafion117 solution to detect the methanol
concentration in water. The study is aimed at the potential use of the
carbon nanotubes array as a methanol sensor for direct methanol fuel
cells (DMFCs). The concentration of methanol in the fuel circulation
loop of a DMFC system is an important operating parameter, because
it determines the electrical performance and efficiency of the fuel cell
system. The sensor is also operative even at ambient temperatures
and responds quickly to changes in the concentration levels of the
methanol. Such a sensor can be easily incorporated into the methanol
fuel solution flow loop in the DMFC system.
Abstract: Toughening of polyamide 6 (PA6)/ Nanoclay (NC) nanocomposites with styrene-ethylene/butadiene-styrene copolymer (SEBS) using maleated styrene-ethylene/butadiene-styrene copolymer (mSEBS)/ as a compatibilizer were investigated by blending them in a co-rotating twin-screw extruder. Response surface method of experimental design was used for optimizing the material and processing parameters. Effect of four factors, including SEBS, mSEBS and NC contents as material variables and order of mixing as a processing factor, on toughness of hybrid nanocomposites were studied. All the prepared samples showed ductile behavior and low temperature Izod impact toughness of some of the hybrid nanocomposites demonstrated 900% improvement compared to the PA6 matrix while the modulus showed maximum enhancement of 20% compared to the pristine PA6 resin.
Abstract: In the present work, we have developed a symmetric electrochemical capacitor based on the nanostructured iron oxide (Fe3O4)-activated carbon (AC) nanocomposite materials. The physical properties of the nanocomposites were characterized by Scanning Electron Microscopy (SEM) and Brunauer-Emmett-Teller (BET) analysis. The electrochemical performances of the composite electrode in 1.0 M Na2SO3 and 1.0 M Na2SO4 aqueous solutions were evaluated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The composite electrode with 4 wt% of iron oxide nanomaterials exhibits the highest capacitance of 86 F/g. The experimental results clearly indicate that the incorporation of iron oxide nanomaterials at low concentration to the composite can improve the capacitive performance, mainly attributed to the contribution of the pseudocapacitance charge storage mechanism and the enhancement on the effective surface area of the electrode. Nevertheless, there is an optimum threshold on the amount of iron oxide that needs to be incorporated into the composite system. When this optimum threshold is exceeded, the capacitive performance of the electrode starts to deteriorate, as a result of the undesired particle aggregation, which is clearly indicated in the SEM analysis. The electrochemical performance of the composite electrode is found to be superior when Na2SO3 is used as the electrolyte, if compared to the Na2SO4 solution. It is believed that Fe3O4 nanoparticles can provide favourable surface adsorption sites for sulphite (SO3 2-) anions which act as catalysts for subsequent redox and intercalation reactions.
Abstract: In recent times there has been a growing interest in the
development of quasi-two-dimensional niobium pentoxide (Nb2O5)
as a semiconductor for the potential electronic applications such as
capacitors, filtration, dye-sensitised solar cells and gas sensing
platforms. Therefore once the purpose is established, Nb2O5 can be
prepared in a number of nano- and sub-micron-structural
morphologies that include rods, wires, belts and tubes. In this study
films of Nb2O5 were prepared on gold plated silicon substrate using
spin-coating technique and subsequently by mechanical exfoliation.
The reason this method was employed was to achieve layers of less
than 15nm in thickness. The sintering temperature of the specimen
was 800oC. The morphology and structural characteristics of the
films were analyzed by Atomic Force Microscopy (AFM), Raman
Spectroscopy, X-ray Photoelectron Spectroscopy (XPS).
Abstract: The lubricating properties of commercially available
mucins originating from different animal organs, namely bovine
submaxillary mucin (BSM) and porcine gastric mucin (PGM), have
been characterized at polymeric surfaces for biomedical applications.
Atomic force microscopy (AFM) and pin-on-disk tribometry have
been employed for tribological studies at nanoscale and macroscale
contacts, respectively. Polystyrene (PS) was employed to represent
‘rigid’ contacts, whereas poly(dimethylsiloxane) (PDMS) was
employed to represent ‘soft contacts’. To understand the lubricating
properties of mucins in correlation with the coverage on surfaces,
adsorption properties of mucins onto the polymeric substrates have
been characterized by means of optical waveguide light-mode
spectroscopy (OWLS). Both mucins showed facile adsorption onto
both polymeric substrates, but the lubricity was highly dependent
upon the pH change between 2 and 7.
Abstract: A computational study at the level density functional theory (DFT) was carried out to investigate the influences of Si and C-doping on the 14N and 27Al quadrupole coupling constant in the (10, 0) zigzag single ? walled Aluminum-Nitride nanotube (AlNNT). To this aim, a 1.16nm, length of AlNNT consisting of 40 Al atoms and 40 N atoms were selected where the end atoms are capped by hydrogen atom. To follow the purpose, three Si atoms and three C atoms were doped instead of three Al atoms and three N atoms as a central ring in the surface of the Si and C-doped AlNNT. At first both of systems optimized at the level of BLYP method and 6-31G (d) basis set and after that, the NQR parameters were calculated at the level BLYP method and 6-311+G** basis set in two optimized forms. The calculate CQ values for both optimized AlNNT systems, raw and Si and C-doped, reveal different electronic environments in the mentioned systems. It was also demonstrated that the end nuclei have the largest CQ values in both considered AlNNT systems. All the calculations were carried out using Gaussian 98 package of program.
Abstract: Silicon nanowire (SiNW) based thermoelectric device (TED) has potential applications in areas such as chip level cooling/ energy harvesting. It is a great challenge however, to assemble an efficient device with these SiNW. The presence of parasitic in the form of interfacial electrical resistance will have a significant impact on the performance of the TED. In this work, we explore the effect of the electrical contact resistance on the performance of a TED. Numerical simulations are performed on SiNW to investigate such effects on its cooling performance. Intrinsically, SiNW individually without the unwanted parasitic effect has excellent cooling power density. However, the cooling effect is undermined with the contribution of the electrical contact resistance.
Abstract: A biocompatible ferrofluid have been prepared by coprecipitation
of FeCl2.4H2O and FeCl3.6H2O under ultrasonic
irradiation and with NaOH as alkaline agent. Cystein was also used
as capping agent in the solution. Magnetic properties of the produced
ferrofluid were then determined by VSM test and magnetite
nanoparticles were characterized by XRD and TEM techniques. The
effect of surfactant to Fe ion weight ratio was also studied during this
project by using two different amount of Dextran. Results showed the
presence of a biocompatible superparamagnetic ferrofluid including
magnetite nanoparticles with particle size ranging under 20 nm. The
increase in the surfactant content results in the narrowing of the size
distribution and reduction of the particle size and more solution
stability.
Abstract: We fabricated multi-walled carbon nanotube (MCNT)
emitters by an electroporetic deposition (EPD) method using a
MCNT-sodium dodecyl sulfate (SDS) suspension. MCNT films were
prepared on graphite tip using EPD. We observe field emission
properties of MCNT film after heat treatment. Consequently, The
MCNT film on graphite tip exhibit good electron emission current.
Abstract: Composites based on a biodegradable polycaprolactone (PCL) containing 0.5, 1.0 and 2.0 wt % of titanium dioxide (TiO2) micro and nanoparticles were prepared by melt mixing and the effect of filler type and contents on the thermal properties, dynamic-mechanical behaviour and morphology were investigated. Measurements of storage modulus and loss modulus by dynamic mechanical analysis (DMA) showed better results for microfilled PCL/TiO2 composites than nanofilled composites, with the same filler content. DSC analysis showed that the Tg and Tc of micro and nanocomposites were slightly lower than those of neat PCL. The crystallinity of the PCL increased with the addition of TiO2 micro and nanoparticles; however, the cc for the PCL was unchanged with micro TiO2 content. The thermal stability of PCL/TiO2 composites were characterized using thermogravimetric analysis (TGA). The initial weight loss (5 wt %) occurs at slightly higher temperature with micro and nano TiO2 addition and with increasing TiO2 content.
Abstract: TiO2 supported nano-ZnO catalyst was prepared by
deposition-precipitation and tested for the trans-esterification
reaction of soybean oil to biodiesel. The TiO2 support stabilized the
nano-ZnO in a dispersed form with limited crystallite size compared
to the unsupported ZnO. The final ZnO dispersion and crystallite size
and the material transfer resistance in the catalyst significantly
influenced the supported nano-ZnO catalyst performance.
Abstract: Memristor is also known as the fourth fundamental
passive circuit element. When current flows in one direction through
the device, the electrical resistance increases and when current flows
in the opposite direction, the resistance decreases. When the current
is stopped, the component retains the last resistance that it had, and
when the flow of charge starts again, the resistance of the circuit will
be what it was when it was last active. It behaves as a nonlinear
resistor with memory. Recently memristors have generated wide
research interest and have found many applications. In this paper we
survey the various applications of memristors which include non
volatile memory, nanoelectronic memories, computer logic,
neuromorphic computer architectures low power remote sensing
applications, crossbar latches as transistor replacements, analog
computations and switches.
Abstract: An efficient and green protocol for the synthesis of α-
aminonitriles derivatives by one-pot reaction of different aldehydes
with amines and trimethylsilyl cyanides has been developed using
natural alumina, alumina sulfuric acid (ASA), nano-γ-alumina, nanoalumina
sulfuric acid (nano-ASA) under microwave irradiation and
solvent-free conditions. The advantages of methods are short reaction
times, high yields, milder conditions and easy work up. The catalysts
can be recovered for the subsequent reactions and reused without any
appreciable loss of efficiency.
Abstract: This paper presents a simple and original method for
the generation of short monocycle pulses based on the transient
response of a passive band-pass filter. The recorded sub-nanosecond
pulses show a good symmetry and a small ringing (13 % of the peak
amplitude). Their spectral density covers the range 3.1 GHz to
10.6 GHz. The possibility to adapt the pulse spectral density to the
indoor FCC frequency mask is demonstrated with a prototype
working at a reduced frequency (FCC/1000). A detection technique is
proposed.
Abstract: The aim of this study was to synthesize the single
walled carbon nanotubes (SWCNTs) and determine their hydrogen
storage capacities. SWCNTs were firstly synthesized by chemical
vapor deposition (CVD) of acetylene (C2H2) on a magnesium oxide
(MgO) powder impregnated with an iron nitrate (Fe(NO3)3·9H2O)
solution. The synthesis parameters were selected as: the synthesis
temperature of 800°C, the iron content in the precursor of 5% and the
synthesis time of 30 min. Purification process of SWCNTs was
fulfilled by microwave digestion at three different temperatures (120,
150 and 200 °C), three different acid concentrations (0.5, 1 and 1.5
M) and for three different time intervals (15, 30 and 60 min). Nitric
acid (HNO3) was used in the removal of the metal catalysts. The
hydrogen storage capacities of the purified materials were measured
using volumetric method at the liquid nitrogen temperature and gas
pressure up to 100 bar. The effects of the purification conditions such
as temperature, time and acid concentration on hydrogen adsorption
were investigated.
Abstract: Sol-gel method has been used to fabricate
nanocomposite films on glass substrates composed halloysite clay
mineral and nanocrystalline TiO2. The methodology for the synthesis
involves a simple chemistry method utilized nonionic surfactant
molecule as pore directing agent along with the acetic acid-based solgel
route with the absence of water molecules. The thermal treatment
of composite films at 450oC ensures elimination of organic material
and lead to the formation of TiO2 nanoparticles onto the surface of
the halloysite nanotubes. Microscopy techniques and porosimetry
methods used in order to delineate the structural characteristics of the
materials. The nanocomposite films produced have no cracks and
active anatase crystal phase with small crystallite size were deposited
on halloysite nanotubes. The photocatalytic properties for the new
materials were examined for the decomposition of the Basic Blue 41
azo dye in solution. These, nanotechnology based composite films
show high efficiency for dye’s discoloration in spite of different
halloysite quantities and small amount of halloysite/TiO2 catalyst
immobilized onto glass substrates. Moreover, we examined the
modification of the halloysite/TiO2 films with silver particles in order
to improve the photocatalytic properties of the films. Indeed, the
presence of silver nanoparticles enhances the discoloration rate of the
Basic Blue 41 compared to the efficiencies obtained for unmodified
films.
Abstract: In this study, mechanically alloyed Al 2024 powder is
densified by conventional sintering and by equal channel angular
pressing (ECAP) with and without back pressure. The powder was
encapsulated in an aluminium can for consolidation through ECAP.
The properties obtained in the compacts by conventional sintering
route and by ECAP are compared. The effect of conventional
sintering and ECAP on consolidation behaviour of powder,
microstructure, density and hardness is discussed. Room temperature
back pressure aided ECAP results in nearly full denser (97% of its
theoretical density) compact at room temperature. NanoIndentation
technique was used to determine the modulus of the consolidated
compacts.
Abstract: The effect of Alumina nanoparticle size on thermophysical
properties, heat transfer performance and pressure loss characteristics of
Aviation Turbine Fuel (ATF)-Al2O3 nanofluids is studied experimentally for
the proposed application of regenerative cooling of semi-cryogenic rocket
engine thrust chambers. Al2O3 particles with mean diameters of 50 nm or 150
nm are dispersed in ATF. At 500C and 0.3% particle volume concentration,
the bigger particles show increases of 17% in thermal conductivity and 55% in
viscosity, whereas the smaller particles show corresponding increases of 21%
and 22% for thermal conductivity and viscosity respectively. Contrary to these
results, experiments to study the heat transfer performance and pressure loss
characteristics show that at the same pumping power, the maximum
enhancement in heat transfer coefficient at 500C and 0.3% concentration is
approximately 47% using bigger particles, whereas it is only 36% using
smaller particles.