Abstract: This paper presents a numerical investigation of two
horizontally mounted four-lobed swirl pipes in terms of swirl
induction effectiveness into flows passing through them. The swirl
flows induced by the two swirl pipes have the potential to improve
the efficiency of Clean-In-Place procedures in a closed processing
system by local intensification of hydrodynamic impact on the
internal pipe surface. Pressure losses, swirl development within the
two swirl pipe, swirl induction effectiveness, swirl decay and wall
shear stress variation downstream of two swirl pipes are analyzed and
compared. It was found that a shorter length of swirl inducing pipe
used in joint with transition pipes is more effective in swirl induction
than when a longer one is used, in that it has a less constraint to the
induced swirl and results in slightly higher swirl intensity just
downstream of it with the expense of a smaller pressure loss. The
wall shear stress downstream of the shorter swirl pipe is also slightly
larger than that downstream of the longer swirl pipe due to the
slightly higher swirl intensity induced by the shorter swirl pipe. The
advantage of the shorter swirl pipe in terms of swirl induction is more
significant in flows with a larger Reynolds Number.
Abstract: Due to the continuous increment of the load demand,
identification of weaker buses, improvement of voltage profile and
power losses in the context of the voltage stability problems has
become one of the major concerns for the larger, complex,
interconnected power systems. The objective of this paper is to
review the impact of Flexible AC Transmission System (FACTS)
controller in Wind generators connected electrical network for
maintaining voltage stability. Wind energy could be the growing
renewable energy due to several advantages. The influence of wind
generators on power quality is a significant issue; non uniform power
production causes variations in system voltage and frequency.
Therefore, wind farm requires high reactive power compensation; the
advances in high power semiconducting devices have led to the
development of FACTS. The FACTS devices such as for example
SVC inject reactive power into the system which helps in maintaining
a better voltage profile. The performance is evaluated on an IEEE 14
bus system, two wind generators are connected at low voltage buses
to meet the increased load demand and SVC devices are integrated at
the buses with wind generators to keep voltage stability. Power
flows, nodal voltage magnitudes and angles of the power network are
obtained by iterative solutions using MIPOWER.
Abstract: DC motors have been widely used in the past
centuries which are proudly known as the workhorse of industrial
systems until the invention of the AC induction motors which makes
a huge revolution in industries. Since then, the use of DC machines
has been decreased due to enormous factors such as reliability,
robustness and complexity but it lost its fame due to the losses. In this
paper a new methodology is proposed to construct a DC motor
through the simulation in LabVIEW to get an idea about its real time
performances, if a change in parameter might have bigger
improvement in losses and reliability.
Abstract: Proposed paper dealt with the modelling and analysis of induction motor based on the mathematical expression using the graphical programming environment of Laboratory Virtual Instrument Engineering Workbench (LabVIEW). Induction motor modelling with the mathematical expression enables the motor to be simulated with the various required parameters. Owing to the invention of variable speed drives study about the induction motor characteristics became complex. In this simulation motor internal parameter such as stator resistance and reactance, rotor resistance and reactance, phase voltage, frequency and losses will be given as input. By varying the speed of motor corresponding parameters can be obtained they are input power, output power, efficiency, torque induced, slip and current.
Abstract: Transmission system performance analysis is vital to
proper planning and operations of power systems in the presence of
deregulation. Key performance indicators (KPIs) are often used as
measure of degree of performance. This paper gives a novel method
to determine the transmission efficiency by evaluating the ratio of
real power losses incurred from a specified transfer direction.
Available Transmission Transfer Efficiency (ATTE) expresses the
percentage of real power received resulting from inter-area available
power transfer. The Tie line (Rated system path) performance is seen
to differ from system wide (Network response) performance and
ATTE values obtained are transfer direction specific. The required
sending end quantities with specified receiving end ATC and the
receiving end power circle diagram are obtained for the tie line
analysis. The amount of real power loss load relative to the available
transfer capability gives a measure of the transmission grid
efficiency.
Abstract: The quality and condition of perishable products
delivered to the market and their subsequent selling prices are
directly affected by the care taken during harvesting and handling.
Mechanical injury, in fact, occurs at all stages, from pre-harvest
operations through post-harvest handling, packing and transport to
the market. The main implications of this damage are the reduction of
the product’s quality and economical losses related to the shelf life
diminution. For most perishable products, the shelf life is relatively
short and it is typically dictated by microbial growth related to the
application of dynamic and static loads during transportation. This
paper presents the correlation between vibration levels and
microbiological growth on strawberries and woodland strawberries
and detects the presence of volatile organic compounds (VOC) in
order to develop an intelligent logistic unit capable of monitoring
VOCs using a specific sensor system. Fresh fruits were exposed to
vibrations by means of a vibrating table in a temperature-controlled
environment. Microbiological analyses were conducted on samples,
taken at different positions along the column of the crates. The values
obtained were compared with control samples not exposed to
vibrations and the results show that different positions along the
column influence the development of bacteria, yeasts and filamentous
fungi.
Abstract: The performance of box-type solar cookers has been
reported by several researchers but little attention was paid to the
effect of the type of insulation material on the energy and exergy
efficiency of these cookers. This research aimed at evaluating the
energy and exergy efficiencies of the box-type cookers containing
different insulation materials. Energy and exergy efficiencies of five
box-type solar cookers insulated with maize cob, air (control), maize
husk, coconut coir and polyurethane foam respectively were obtained
over a period of three years. The cookers were evaluated using water
heating test procedures in determining the energy and exergy
analysis. The results were subjected to statistical analysis using
ANOVA. The result shows that the average energy input for the five
solar cookers were: 245.5, 252.2, 248.7, 241.5 and 245.5J
respectively while their respective average energy losses were: 201.2,
212.7, 208.4, 189.1 and 199.8J. The average exergy input for five
cookers were: 228.2, 234.4, 231.1, 224.4 and 228.2J respectively
while their respective average exergy losses were: 223.4, 230.6,
226.9, 218.9 and 223.0J. The energy and exergy efficiency was
highest in the cooker with coconut coir (37.35 and 3.90%
respectively) in the first year but was lowest for air (11 and 1.07%
respectively) in the third year. Statistical analysis showed significant
difference between the energy and exergy efficiencies over the years.
These results reiterate the importance of a good insulating material
for a box-type solar cooker.
Abstract: Poly bag and mulch films for agricultural field caused
pose environmental problem due to the non-degradable plastics
wastes upon disposal. Thus, a degradable poly bag was designed with
hybrid sago starch (SS) and polyvinyl alcohol (PVA). Two Different
blended compositions of SS and PVA hybrid have been compounded.
Then, the hybrids blended are mixed with linear line density
polyethylene (LLDPE) resin to fabricate poly bag film through
conventional film blowing process. Samples of LLDPE, SS and PVA
hybrid film were exposed to UV light and soil burial. The weight
losses were determined during degradation process. Hybrid film by
degradation of starch was found to hydrolyze and hydroxyl groups
decrease on esterification upon exposure to soil burial and uv
radiation. It was found out that, the hybrid film for 60% of SS
composition showed greatest degradation in soil and UV radiation.
Abstract: The introduction of degradable plastic materials into
agricultural sectors has represented a promising alternative to
promote green agriculture and environmental friendly of modern
farming practices. Major challenges of developing degradable
agricultural films are to identify the most feasible types of
degradation mechanisms, composition of degradable polymers and
related processing techniques. The incorrect choice of degradable
mechanisms to be applied during the degradation process will cause
premature losses of mechanical performance and strength. In order to
achieve controlled process of agricultural film degradation, the
compositions of degradable agricultural film also important in order
to stimulate degradation reaction at required interval of time and to
achieve sustainability of the modern agricultural practices. A set of
photodegradable polyethylene based agricultural film was developed
and produced, following the selective optimization of processing
parameters of the agricultural film manufacturing system. Example of
agricultural films application for oil palm seedlings cultivation is
presented.
Abstract: Parabolic solar trough systems have seen limited
deployments in cold northern climates as they are more suitable for
electricity production in southern latitudes. A numerical dynamic
model is developed to simulate troughs installed in cold climates and
validated using a parabolic solar trough facility in Winnipeg. The
model is developed in Simulink and will be utilized to simulate a trigeneration
system for heating, cooling and electricity generation in
remote northern communities. The main objective of this simulation
is to obtain operational data of solar troughs in cold climates and use
the model to determine ways to improve the economics and address
cold weather issues.
In this paper the validated Simulink model is applied to simulate a
solar assisted absorption cooling system along with electricity
generation using Organic Rankine Cycle (ORC) and thermal storage.
A control strategy is employed to distribute the heated oil from solar
collectors among the above three systems considering the
temperature requirements. This modelling provides dynamic
performance results using measured meteorological data recorded
every minute at the solar facility location. The purpose of this
modeling approach is to accurately predict system performance at
each time step considering the solar radiation fluctuations due to
passing clouds. Optimization of the controller in cold temperatures is
another goal of the simulation to for example minimize heat losses in
winter when energy demand is high and solar resources are low.
The solar absorption cooling is modeled to use the generated heat
from the solar trough system and provide cooling in summer for a
greenhouse which is located next to the solar field.
The results of the simulation are presented for a summer day in
Winnipeg which includes comparison of performance parameters of
the absorption cooling and ORC systems at different heat transfer
fluid (HTF) temperatures.
Abstract: Real bronchial tree is very complicated piping system.
Analysis of flow and pressure losses in this system is very difficult.
Due to the complex geometry and the very small size in the lower
generations is examination by CFD possible only in the central part
of bronchial tree. For specify the pressure losses of lower generations
is necessary to provide a mathematical equation. Determination of
mathematical formulas for calculation of pressure losses in the real
lungs is time consuming and inefficient process due to its complexity
and diversity. For these calculations is necessary to slightly simplify
the geometry of lungs (same cross-section over the length of
individual generation) or use one of the idealized models of lungs
(Horsfield, Weibel). The article compares the values of pressure
losses obtained from CFD simulation of air flow in the central part of
the real bronchial tree with the values calculated in a slightly
simplified real lungs by using a mathematical relationship derived
from the Bernoulli and continuity equations. The aim of the article is
to analyse the accuracy of the analytical method and its possibility of
use for the calculation of pressure losses in lower generations, which
is difficult to solve by numerical method due to the small geometry.
Abstract: Multi-Level Inverter technology has been developed in the area of high-power medium-voltage energy scheme, because of their advantages such as devices of lower rating can be used thereby enabling the schemes to be used for high voltage applications. Reduced Total Harmonic Distortion (THD).Since the dv/dt is low; the Electromagnetic Interference from the scheme is low. To avoid the switching losses Lower switching frequencies can be used. In this paper present a survey of various topologies, control strategy and modulation techniques used by these inverters. Here the regenerative and superior topologies are also discussed.
Abstract: The paper presents a practical three-phase PWM
inverter suitable for low voltage, low rating energy efficient systems.
The work in the paper is conducted with the view to establishing the
significance of the loss contribution from the PWM inverter in the
determination of the complete losses of a photovoltaic (PV) arraypowered
induction motor drive water pumping system. Losses
investigated include; conduction and switching loss of the devices
and gate drive losses. It is found that the PWM inverter operates at a
reasonable variable efficiency that does not fall below 92%
depending on the load. The results between the simulated and
experimental results for the system with or without a maximum
power tracker (MPT) compares very well, within an acceptable range
of 2% margin.
Abstract: This paper presents two types of microstrip bandpass
filter (BPF) at microwave frequencies. The first one is a tunable BPF
using planar patch resonators based on a varactor diode. The filter is
formed by a triple mode circular patch resonator with two pairs of
slots, in which the varactor diodes are connected. Indeed, this filter is
initially centered at 2.4 GHz; the center frequency of the tunable
patch filter could be tuned up to 1.8 GHz simultaneously with the
bandwidth, reaching high tuning ranges. Lossless simulations were
compared to those considering the substrate dielectric, conductor
losses and the equivalent electrical circuit model of the tuning
element in order to assess their effects. Within these variations,
simulation results showed insertion loss better than 2 dB and return
loss better than 10 dB over the passband. The second structure is a
BPF for ultra-wideband (UWB) applications based on multiple-mode
resonator (MMR) and rectangular-shaped defected ground structure
(DGS). This filter, which is compact size of 25.2 x 3.8 mm2, provides
in the pass band an insertion loss of 0.57 dB and a return loss greater
than 12 dB. The proposed filters presents good performances and the
simulation results are in satisfactory agreement with the
experimentation ones reported elsewhere.
Abstract: This work reports the potential of using Palm Kernel
(PK) ash and shell as a partial substitute for Portland Cement (PC)
and coarse aggregate in the development of mortar and concrete. PK
ash and shell are agro-waste materials from palm oil mills, the
disposal of PK ash and shell is an environmental problem of concern.
The PK ash has pozzolanic properties that enables it as a partial
replacement for cement and also plays an important role in the
strength and durability of concrete, its use in concrete will alleviate
the increasing challenges of scarcity and high cost of cement. In order
to investigate the PC replacement potential of PK ash, three types of
PK ash were produced at varying temperature (350-750C) and they
were used to replace up to 50% PC. The PK shell was used to replace
up to 100% coarse aggregate in order to study its aggregate
replacement potential. The testing programme included material
characterisation, the determination of compressive strength, tensile
splitting strength and chemical durability in aggressive sulfatebearing
exposure conditions. The 90 day compressive results showed
a significant strength gain (up to 26.2 N/mm2). The Portland cement
and conventional coarse aggregate has significantly higher influence
in the strength gain compared to the equivalent PK ash and PK shell.
The chemical durability results demonstrated that after a prolonged
period of exposure, significant strength losses in all the concretes
were observed. This phenomenon is explained, due to lower change
in concrete morphology and inhibition of reaction species and the
final disruption of the aggregate cement paste matrix.
Abstract: For the treatment of acute and chronic lung diseases it is preferred to deliver medicaments by inhalation. The drug is delivered directly to tracheobronchial tree. This way allows the given medicament to get directly into the place of action and it makes rapid onset of action and maximum efficiency. The transport of aerosol particles in the particular part of the lung is influenced by their size, anatomy of the lungs, breathing pattern and airway resistance. This article deals with calculation of airway resistance in the lung model of Horsfield. It solves the problem of determination of the pressure losses in bifurcation and thus defines the pressure drop at a given location in the bronchial tree. The obtained data will be used as boundary conditions for transport of aerosol particles in a central part of bronchial tree realized by Computational Fluid Dynamics (CFD) approach. The results obtained from CFD simulation will allow us to provide information on the required particle size and optimal inhalation technique for particle transport into particular part of the lung.
Abstract: The legends about “user-friendly” and “easy-to-use”
birotical tools (computer-related office tools) have been spreading
and misleading end-users. This approach has led us to the extremely
high number of incorrect documents, causing serious financial losses
in the creating, modifying, and retrieving processes. Our research
proved that there are at least two sources of this underachievement:
(1) The lack of the definition of the correctly edited, formatted
documents. Consequently, end-users do not know whether their
methods and results are correct or not. They are not aware of their
ignorance. They are so ignorant that their ignorance does not allow
them to realize their lack of knowledge. (2) The end-users’ problem
solving methods. We have found that in non-traditional programming
environments end-users apply, almost exclusively, surface approach
metacognitive methods to carry out their computer related activities,
which are proved less effective than deep approach methods.
Based on these findings we have developed deep approach
methods which are based on and adapted from traditional
programming languages. In this study, we focus on the most popular
type of birotical documents, the text based documents. We have
provided the definition of the correctly edited text, and based on this
definition, adapted the debugging method known in programming.
According to the method, before the realization of text editing, a
thorough debugging of already existing texts and the categorization
of errors are carried out. With this method in advance to real text
editing users learn the requirements of text based documents and also
of the correctly formatted text.
The method has been proved much more effective than the
previously applied surface approach methods. The advantages of the
method are that the real text handling requires much less human and
computer sources than clicking aimlessly in the GUI (Graphical User
Interface), and the data retrieval is much more effective than from
error-prone documents.
Abstract: As the current status and growth of Indian automobile
industry is remarkable, transportation sectors are the main concern in
terms of energy security and climate change. Due to rising demand of
fuel and its dependency on foreign countries that affects the GDP of
nation, suggests that penetration of electrical vehicle will increase in
near future. So in this context analysis is done if the 10 percent of
conventional vehicles including cars, three wheelers and two
wheelers becomes electrical vehicles in near future which is also a
part of Nations Electric Mobility Mission Plan then the saving which
improves the nation’s economy is analyzed in detail. Whether the
Indian electricity grid is capable of taking this load with current
generation and demand all over the country is also analyzed in detail.
Current situation of Indian grid is analyzed and how the gap between
generation and demand can be reduced is discussed in terms of
increasing generation capacity and energy conservation measures.
Electrical energy conservation measures in Industry and especially in
rural areas have been analyzed to improve performance of Indian
electricity grid in context of electrical vehicle penetration in near
future. Author was a part of Vishvakarma yojna in which energy
losses were measured in 255 villages of Gujarat and solutions were
suggested to mitigate them and corresponding reports was submitted
to the authorities of Gujarat government.
Abstract: Image spam is a kind of email spam where the spam
text is embedded with an image. It is a new spamming technique
being used by spammers to send their messages to bulk of internet
users. Spam email has become a big problem in the lives of internet
users, causing time consumption and economic losses. The main
objective of this paper is to detect the image spam by using histogram
properties of an image. Though there are many techniques to
automatically detect and avoid this problem, spammers employing
new tricks to bypass those techniques, as a result those techniques are
inefficient to detect the spam mails. In this paper we have proposed a
new method to detect the image spam. Here the image features are
extracted by using RGB histogram, HSV histogram and combination
of both RGB and HSV histogram. Based on the optimized image
feature set classification is done by using k- Nearest Neighbor(k-NN)
algorithm. Experimental result shows that our method has achieved
better accuracy. From the result it is known that combination of RGB
and HSV histogram with k-NN algorithm gives the best accuracy in
spam detection.
Abstract: This paper proposes a backward/forward sweep
method to analyze the power flow in radial distribution systems. The
distribution system has radial structure and high R/X ratios. So the
newton-raphson and fast decoupled methods are failed with
distribution system. The proposed method presents a load flow study
using backward/forward sweep method, which is one of the most
effective methods for the load-flow analysis of the radial distribution
system. By using this method, power losses for each bus branch and
voltage magnitudes for each bus node are determined. This method
has been tested on IEEE 33-bus radial distribution system and
effective results are obtained using MATLAB.