Abstract: The grain quality of chickpea in Iran is low and
instable, which may be attributed to the evolution of cultivars with a
narrow genetic base making them vulnerable to biotic stresses. Four
chickpea varieties from diverse geographic origins were chosen and
arranged in a randomized complete block design. Mesorhizobium sp.
cicer strain SW7 was added to all the chickpea seeds. Chickpea seeds
were planted on October 9, 2013. Each genotype was sown 5 m in
length, with 35 cm inter-row spacing, in 3 rows. Weeds were
removed manually in all plots. Results showed that Analysis of
variance on the studied traits showed significant differences among
genotypes for N, P, K and Fe contents of chickpea, but there is not a
significant difference among Ca, Zn and Mg continents of chickpea.
The experimental coefficient of variation (CV) varied from 7.3 to
15.8. In general, the CV value lower than 20% is considered to be
good, indicating the accuracy of conducted experiments. The highest
grain N was observed in Hashem and Jam cultivars. The highest grain
P was observed in Jam cultivar. Phosphorus content (mg/100g)
ranged from 142.3 to 302.3 with a mean value of 221.3. The negative
correlation (-0.126) was observed between the N and P of chickpea
cultivars. The highest K and Fe contents were observed in Jam
cultivar.
Abstract: Structural Equation Modeling (SEM) was used to test
a hypothesized model explaining Malaysian hypermarket customers’
perceptions of brand trust (BT), customer perceived value (CPV) and
perceived service quality (PSQ) on building their brand loyalty
(CBL) and generating positive word-of-mouth communication
(WOM). Self-administered questionnaires were used to collect data
from 374 Malaysian hypermarket customers from Mydin, Tesco,
Aeon Big and Giant in Kuala Lumpur, a metropolitan city of
Malaysia. The data strongly supported the model exhibiting that BT,
CPV and PSQ are prerequisite factors in building customer brand
loyalty, while PSQ has the strongest effect on prediction of customer
brand loyalty compared to other factors. Besides, the present study
suggests the effect of the aforementioned factors via customer brand
loyalty strongly contributes to generate positive word of mouth
communication.
Abstract: This paper proposes techniques like MT CMOS,
POWER GATING, DUAL STACK, GALEOR and LECTOR to
reduce the leakage power. A Full Adder has been designed using
these techniques and power dissipation is calculated and is compared
with general CMOS logic of Full Adder.
Simulation results show the validity of the proposed techniques is
effective to save power dissipation and to increase the speed of
operation of the circuits to a large extent.
Abstract: To study the effect of the cross direction in bead
wheat, three hybrid combinations (Babyle 113, Iratome), (Sawa,
Tamose2) and (Al Hashymya, Al Iraq) were tested for plant height,
spike and awn length, number of grains per spike, 1000-grain weight,
number of tillers/m and grain yield. The results revealed that the
direction of the crosses significantly effect on the number of
grains/spike, number of tillers/m and grain yields. Grain yield was
positively and significantly correlated with 1000-grain weight,
number of grains per spike and tillers. Depend on the results of
heritability and genetic advance it was suggested that 1000-grain
weight, number of grains per spike and tillers should be given
emphasis for future wheat yield improvement programs.
Abstract: Zinc oxide (ZnO) is one of the light emitting materials in ultraviolet (UV) region. In addition, ZnO nanostructures are also attracting increasing research interest as buildingblocks for UV optoelectronic applications. We have succeeded in synthesizing vertically-aligned ZnO nanostructures by laser interference patterning, which is catalyst-free and non-contact technique. In this study, vertically-aligned ZnO nanowall arrays were synthesized using two-beam interference. The maximum height and average thickness of the ZnO nanowalls were about 4.5µm and 200 nm, respectively.UV lasing from a piece of the ZnO nanowall was obtained under the third harmonic of a Q-switched Nd:YAG laser excitation, and the estimated threshold power density for lasing was about 150 kW/cm2. Furthermore, UV lasing from the vertically-aligned ZnO nanowall was also achieved. The results indicate that ZnO nanowalls can be applied to random laser.
Abstract: Absorptive capacity generally facilitates the adoption
of innovation. How does this relationship change when economic
return is not the sole driver of innovation uptake? We investigate
whether absorptive capacity facilitates the adoption of green
innovation based on a survey of 79 construction companies in
Scotland. Based on the results of multiple regression analyses, we
confirm that existing knowledge utilisation (EKU), knowledge
building (KB) and external knowledge acquisition (EKA) are
significant predictors of green process GP), green administrative
(GA) and green technical innovation (GT), respectively. We discuss
the implications for theories of innovation adoption and knowledge
enhancement associated with environmentally-friendly practices.
Abstract: A nanocrystalline thin film of ZnSe was successfully
electrodeposited on copper substrate using a non-aqueous solution
and subsequently annealed in air at 400°C. XRD analysis indicates
the polycrystalline deposit of (111) plane in both the cases. The
sharpness of the peak increases due to annealing of the film and
average grain size increases to 20 nm to 27nm. SEM photograph
indicate that grains are uniform and densely distributed over the
surface. Annealing increases the average grain size by 20%. The EDS
spectroscopy shows the ratio of Zn & Se is 1.1 in case of annealed
film. AFM analysis indicates the average roughness of the film
reduces from 181nm to 165nm due to annealing of the film. The
bandgap also decreases from 2.71eV to 2.62eV.
Abstract: Concrete is found to undergo degradation when
subjected to elevated temperatures and loose substantial amount of its
strength. The loss of strength in concrete is mainly attributed to
decomposition of C-S-H and release of physically and chemically
bound water, which begins when the exposure temperature exceeds
100°C. When such a concrete comes in contact with moisture, the
cement paste is found rehydrate and considerable amount of strength
lost is found to recover. This paper presents results of an
experimental program carried out to investigate the effect of recuring
on strength gain of OPC concrete specimens subjected to elevated
temperatures from 200°C to 800°C, which were subjected to
retention time of two hours and four hours at the designated
temperature. Strength recoveries for concrete subjected to 7
designated elevated temperatures are compared. It is found that the
efficacy of recuring as a measure of strength recovery reduces with
increase in exposure temperature.
Abstract: Near-infrared spectroscopy (NIRS) has been widely
used as a non-invasive method to measure brain activity, but it is
corrupted by baseline drift noise. Here we present a method to measure
regional cerebral blood flow as a derivative of NIRS output. We
investigate whether, when listening to languages, blood flow can
reasonably localize and represent regional brain activity or not. The
prefrontal blood flow distribution pattern when advanced
second-language listeners listened to a second language (L2) was most
similar to that when listening to their first language (L1) among the
patterns of mean and standard deviation. In experiments with 25
healthy subjects, the maximum blood flow was localized to the left
BA46 of advanced listeners. The blood flow presented is robust to
baseline drift and stably localizes regional brain activity.
Abstract: Random epistemologies and hash tables have garnered
minimal interest from both security experts and experts in the last
several years. In fact, few information theorists would disagree with
the evaluation of expert systems. In our research, we discover how
flip-flop gates can be applied to the study of superpages. Though
such a hypothesis at first glance seems perverse, it is derived from
known results.
Abstract: The paper presents a plastic analysis procedure based
on the energy balance concept for performance based seismic retrofit
of multi-story multi-bay masonry infilled reinforced concrete (R/C)
frames with a ‘soft’ ground story using passive energy dissipation
(PED) devices with the objective of achieving a target performance
level of the retrofitted R/C frame for a given seismic hazard level at
the building site. The proposed energy based plastic analysis
procedure was employed for developing performance based design
(PBD) formulations for PED devices for a simulated application in
seismic retrofit of existing frame structures designed in compliance
with the prevalent standard codes of practice. The PBD formulations
developed for PED devices were implemented for simulated seismic
retrofit of a representative code-compliant masonry infilled R/C
frame with a ‘soft’ ground story using friction dampers as the PED
device. Non-linear dynamic analyses of the retrofitted masonry
infilled R/C frames is performed to investigate the efficacy and
accuracy of the proposed energy based plastic analysis procedure in
achieving the target performance level under design level
earthquakes. Results of non-linear dynamic analyses demonstrate that
the maximum inter-story drifts in the masonry infilled R/C frames
with a ‘soft’ ground story that is retrofitted with the friction dampers
designed using the proposed PBD formulations are controlled within
the target drifts under near-field as well far-field earthquakes.
Abstract: PVC foam-fly ash composites (PVC-FA) are
characterized for their structural, morphological, mechanical and
thermal properties. The tensile strength of the composites increased
modestly with higher fly ash loading, while there was a significant
increase in the elastic modulus for the same composites. On the other
hand, a decrease in elongation at UTS was observed upon increasing
fly ash content due to increased rigidity of the composites. Similarly,
the flexural modulus increased as the fly ash loading increased,
where the composites containing 25 phr fly ash showed the highest
flexural strength. Thermal properties of PVC-fly ash composites were
determined by Thermo Gravimetric Analysis (TGA). The
microstructural properties were studied by Scanning Electron
Microscopy (SEM). SEM results confirm that fly ash particles were
mechanically interlocked in PVC matrix with good interfacial
interaction with the matrix. Particle agglomeration and debonding
was observed in samples containing higher amounts of fly ash.
Abstract: Two types of glass fibers having different lengths
(1/16" and 1/32") were added into rigid PVC foams to enhance the
dimensional stability of extruded rigid Polyvinyl Chloride (PVC)
foam at different concentrations (0-20 phr) using a single screw
profile extruder. PVC foam-glass fiber composites (PVC-GF) were
characterized for their dimensional stability, structural, thermal, and
mechanical properties. Experimental results show that the
dimensional stability, heat resistance, and storage modulus were
enhanced without compromising the tensile and flexural strengths of
the composites. Overall, foam composites which were prepared with
longer glass fibers exhibit better mechanical and thermal properties
than those prepared with shorter glass fibers due to higher
interlocking between the fibers and the foam cells, which result in
better load distribution in the matrix.
Abstract: In this paper, the formulation of a new group explicit
method with a fourth order accuracy is described in solving the two
dimensional Helmholtz equation. The formulation is based on the
nine-point fourth order compact finite difference approximation
formula. The complexity analysis of the developed scheme is also
presented. Several numerical experiments were conducted to test the
feasibility of the developed scheme. Comparisons with other existing
schemes will be reported and discussed. Preliminary results indicate
that this method is a viable alternative high accuracy solver to the
Helmholtz equation.
Abstract: Two tragic tsunamis that devastated the west coast of
Sumatra Island, Indonesia in 2004 and North East Japan in 2011 had
damaged bridges to various extents. Tsunamis have resulted in the
catastrophic deterioration of infrastructures i.e. coastal structures,
utilities and transportation facilities. A bridge structure performs vital
roles to enable people to perform activities related to their daily needs
and for development. A damaged bridge needs to be repaired
expeditiously. In order to understand the effects of tsunami forces on
bridges, experimental tests are carried out to measure the
characteristics of hydrodynamic force at various wave heights.
Coastal bridge models designed at a 1:40 scale are used in a 24.0 m
long hydraulic flume with a cross section of 1.5 m by 2.0 m. The
horizontal forces and uplift forces in all cases show that forces
increase nonlinearly with increasing wave amplitude.
Abstract: This paper present the experimental work of double
unit tunnel form building (TFB) subjected to in-plane lateral cyclic
loading. A one third scale of 3-storey double unit of TFB is tested
until its strength degradation. Then, the TFB is repaired and
retrofitted using additional shear wall, steel angle and CFRP sheet.
The crack patterns, lateral strength, stiffness, ductility and equivalent
viscous damping (EVD) were analyzed and compared before and
after repair and retrofit. The result indicates that the lateral strength
increases by 22% in pushing and 27% in pulling direction. Moreover,
the stiffness and ductility obtained before and after retrofit increase
tremendously by 87.87% and 39.66%, respectively. Meanwhile, the
energy absorption measured by equivalent viscous damping obtained
after retrofit increase by 12.34% in pulling direction. It can be
concluded that the proposed retrofit method is capable to increase the
lateral strength capacity, stiffness and energy absorption of double
unit TFB.
Abstract: The current study explored the effect of economic
development, financial development and institutional quality on
environmental destruction in upper-middle income countries during
the time period of 1999-2011. The dependent variable is logarithm of
carbon dioxide emissions that can be considered as an index for
destruction or quality of the environment given to its effects on the
environment. Financial development and institutional development
variables as well as some control variables were considered. In order
to study cross-sectional correlation among the countries under study,
Pesaran and Friz test was used. Since the results of both tests show
cross-sectional correlation in the countries under study, seemingly
unrelated regression method was utilized for model estimation. The
results disclosed that Kuznets’ environmental curve hypothesis is
confirmed in upper-middle income countries and also, financial
development and institutional quality have a significant effect on
environmental quality. The results of this study can be considered by
policy makers in countries with different income groups to have
access to a growth accompanied by improved environmental quality.
Abstract: Ficus deltoidea from the Moraceae family is a popular
medicinal herb in Malaysia. It possesses strong antioxidant and antiinflammatory
properties. In the present study, the anti-inflammatory
effects of F. deltoidea extract on UVB-irradiated HaCaT
Keratinocytes were investigated. HaCaT Keratinocytes were UVBirradiated
(12.5 mJ/cm3) and were treated with 0.05, 0.08 or 0.1% of
F. deltoidea extract. Cell viability following UVB irradiation was
significantly higher in the groups treated with the F. deltoidea extract
at doses of 0.05, 0.08 or 0.1% than in control group with UVB
irradiation only. Tumor necrosis factor-α (TNF-α), interleukin-1α
(IL-1α), interleukin-6 (IL-6) and cyclooxygenase (COX-2) play
primary roles in the inflammation process upon UV irradiation and
are known to be stimulated by UVB irradiation. Treatment with the
F. deltoidea extract dramatically inhibited the UV-induced TNF-α,
IL-1α, IL-6, and COX-2 expression. These results suggest that the F.
deltoidea extract inhibits the production of pro-inflammatory
cytokines and may be an effective protective agent for the treatment
of skin diseases.
Abstract: In a human tracking system, expanding a monitoring
range of one system is complicating the management of devices and
increasing its cost. Therefore, we propose a method to realize a
wide-range human tracking by connecting small systems. In this paper,
we examined an agent deploy method and information contents across
the heterogeneous human tracking systems. By implementing the
proposed method, we can construct a human tracking system across
heterogeneous systems, and the system can track a target continuously
between systems.
Abstract: The case study presents the progression of a project management of Al-Shifa, a healthcare information system in Oman. The case study describes the evolution of the implementation of a healthcare information system tailored to meet the needs of the healthcare units under the supervision of the Ministry of Health (MOH) in Oman. A focus group methodology was used for collecting the relevant information from the main project's stakeholders. In addition reports about the project made available for the researchers. The case analysis is made based on the Project Management approach developed by the Project Management Institute (PMI). The main finding that there was no formal project management approach adopted by the MOH for the development and implementation of the herewith mentioned healthcare information system project. Furthermore, the project had suffered a scope creep in terms of features, cost and time-schedule. The recommendations of the authors, for the rescue of the project from its current dilemma, consist of technological, administrative and human resources development actions.