Abstract: In the present study, feasibility of the selective surface
hydrophilization of polyvinyl chloride (PVC) by microwave treatment
was evaluated to facilitate the separation from automotive shredder
residue (ASR), by the froth flotation. The combination of 60 sec
microwave treatment with PAC, a sharp and significant decrease about
16.5° contact angle of PVC was observed in ASR plastic compared
with other plastics. The microwave treatment with the addition of PAC
resulted in a synergetic effect for the froth flotation, which may be a
result of the 90% selective separation of PVC from ASR plastics, with
82% purity. While, simple mixing with a nanometallic Ca/CaO/PO4
dispersion mixture immobilized 95-100% of heavy metals in ASR
soil/residues. The quantity of heavy metals leached from thermal
residues after treatment by nanometallic Ca/CaO/PO4 was lower than
the Korean standard regulatory limit for hazardous waste landfills.
Microwave treatment can be a simple and effective method for PVC
separation from ASR plastics.
Abstract: In this article was evaluated the protective effect of
the alternative concrete obtained from the binary mixture of fly ash,
and iron and steel slag. After mixing the cement with aggregates,
structural steel was inserted in the matrix cementitious. The study
was conducted comparatively with specimens exposed to natural
conditions free of chloride ion. The chloride ion effect on the
specimens accelerated under controlled conditions (3.5% NaCl and
25°C temperature). The impedance data were acquired in a range of 1
mHz to 100 kHz.
Abstract: The main cause of Alzheimer disease (AD) was
believed to be mainly due to the accumulation of free radicals owing
to oxidative stress (OS) in brain tissue. The mechanism of the
neurotoxicity of Aluminum chloride (AlCl3) induced AD in
hippocampus Albino wister rat brain tissue, the curative & the
protective effects of Lipidium sativum group (LS) water extract were
assessed after 8 weeks by attenuated total reflection spectroscopy
ATR-IR and histologically by light microscope. ATR-IR results
revealed that the membrane phospholipid undergo free radical
attacks, mediated by AlCl3, primary affects the polyunsaturated fatty
acids indicated by the increased of the olefinic -C=CH sub-band area
around 3012 cm-1 from the curve fitting analysis. The narrowing in
the half band width (HBW) of the sνCH2 sub-band around 2852 cm-1
due to Al intoxication indicates the presence of trans form fatty acids
rather than gauch rotomer. The degradation of hydrocarbon chain to
shorter chain length, increasing in membrane fluidity, disorder, and
decreasing in lipid polarity in AlCl3 group indicated by the detected
changes in certain calculated area ratios compared to the control.
Administration of LS was greatly improved these parameters
compared to the AlCl3 group. Al influences the Aβ aggregation and
plaque formation, which in turn interferes to and disrupts the
membrane structure. The results also showed a marked increase in
the β-parallel and antiparallel structure, that characterize the Aβ
formation in Al-induced AD hippocampal brain tissue, indicated by
the detected increase in both amide I sub-bands around 1674, 1692
cm-1. This drastic increase in Aβ formation was greatly reduced in the
curative and protective groups compared to the AlCl3 group and
approached nearly the control values. These results supported too by
the light microscope. AlCl3 group showed significant marked
degenerative changes in hippocampal neurons. Most cells appeared
small, shrieked and deformed. Interestingly, the administration of LS
in curative and protective groups markedly decreases the amount of
degenerated cells compared to the non-treated group. In addition, the
intensity of congo red stained cells was decreased. Hippocampal
neurons looked more/or less similar to those of control. This study showed a promising therapeutic effect of Lipidium
sativum group (LS) on AD rat model that seriously overcome the
signs of oxidative stress on membrane lipid and restore the protein
misfolding.
Abstract: In present study, a large deposit of oolitic iron ore of
Late Carboniferous-Permotriassic-Lower Jurassic age was discovered
in Wadi Halfa and Argein areas, North Sudan. It seems that the iron
ore mineralization exists in the west and east bank of the River Nile
of the study area that are found on the Egyptian-Sudanese border.
The Carboniferous-Lower Jurassic age strata were covered by 67
sections and each section has been examined and carefully described.
The iron-ore in Wadi Halfa occurs as oolitic ironstone and contained
two horizons: (A) horizon and (B) horizon. Only horizon (A) was
observed in southern Argein area. The texture of the ore is variable
depending on the volume of the component. In thin sections, the
average of the ooids was ranged between 90%-80%. The matrix
varies between 10%-20% by volume and detritus quartz in other
component my reach up to 30% by volume in sandy massive ore.
Ooids size ranges from 0.2mm-1.00 mm on average in very coarse
ooids may attend up to 1 mm in size. The matrix around the ooids is
dominated by iron hydroxide, carbonate, fine, and amorphous silica.
The probable ore reserve estimate of 1.234 billion at a head grade of
41.29% Fe for the Wadi Halfa Oolitic Ironstone Formation. The iron
ore shows higher content of phosphorus ranges from 6.15% to 0.16%,
with mean 1.45%. The new technology Hatch–Ironstone Chloride
Segregation (HICS) can be used to produce commercial-quality of
iron and reduce phosphorus and silica to acceptable levels for steel
industry. The presence of infrastructures in addition to the presence
of massive quantities of iron ore would make exploitation
economically.
Abstract: CuO thin films were deposited by spray ultrasonic
pyrolysis with different precursor solution. Two staring solution slats
were used namely: copper acetate and copper chloride. The influence
of these solutions on CuO thin films proprieties of is instigated. The
X rays diffraction (XDR) analysis indicated that the films deposed
with copper acetate are amorphous however the films elaborated with
copper chloride have monoclinic structure. UV- Visible transmission
spectra showed a strong absorbance of the deposited CuO thin films
in the visible region. Electrical characterization has shown that CuO
thin films prepared with copper acetate have a higher electrical
conductivity.
Abstract: The study investigated efficiency cassava peel carbon
and Zinc Chloride activated cassava peel carbon at 1:3, 2:3 and 1:1
activation levels in the removal of nitrates from oxidized cassava
processing wastewater. Results showed that the CPC and CPAC were
effective in adsorption of nitrates. A summary of results from the
study revealed that CPAC at 1:3 exhibited the highest initial
decontamination (69.5% after 2 hrs) while CPAC at 1:1 activation
ratio showed a slower initial decontamination rate. The CPC &
CPAC exhibited Langmuir Rα values of 0.15, 0.11, 0.09, and 0.07 for
the 0:1, 1:3, 2:3 and 1:1 confirming its suitability as adsorption
material.
Abstract: Ceramic obtained on the base of aluminum oxide has
wide application range, because it has unique properties, for example,
wear-resistance, dielectric characteristics, and exploitation ability at
high temperatures and in corrosive atmosphere. Low temperature
synthesis of α-Al2O3 is energo-economical process and it is topical
for developing technologies of corundum ceramics fabrication. In the present work possibilities of low temperature transformation
of oxyhydroxides in α-Al2O3, during the presence of small amount of
rare–earth elements compounds (also Th, Re), have been discussed.
Aluminum unstable oxyhydroxides have been obtained by hydrolysis
of aluminium isopropoxide, nitrates, sulphate, and chloride in
alkaline environment at 80-90ºC temperatures. β-Al(OH)3 has been
received from aluminum powder by ultrasonic development. Drying
of oxyhydroxide sol has been conducted with presence of various
types seeds, which amount reaches 0,1-0,2% (mas). Neodymium,
holmium, thorium, lanthanum, cerium, gadolinium, disprosium
nitrates and rhenium carbonyls have been used as seeds and they
have been added to the sol specimens in amount of 0.1-0.2% (mas)
calculated on metals. Annealing of obtained gels is carried out at 70–
1100ºC for 2 hrs. The same specimen transforms in α-Al2O3 at
1100ºC. At this temperature in case of presence of lanthanum and
gadolinium transformation takes place by 70-85%. In case of
presence of thorium stabilization of γ-and θ-phases takes place. It is
established, that thorium causes inhibition of α-phase generation at
1100ºC, and at the time when in all other doped specimens α-phase is
generated at lower temperatures (1000-1050ºC). Synthesis of various
type compounds and simultaneous consolidation has developed in the
furnace of OXY-GON. Composite materials containing oxide and
non-oxide components close to theoretical data have been obtained in
this furnace respectively. During the work the following devices have
been used: X-ray diffractometer DRON-3M (Cu-Kα, Ni filter,
2º/min), High temperature vacuum furnace OXY-GON, electronic
scanning microscopes Nikon ECLIPSE LV 150, NMM-800TRF,
planetary mill Pulverisette 7 premium line, SHIMADZU Dynamic
Ultra Micro Hardness Tester, DUH-211S, Analysette 12 Dyna sizer.
Abstract: The effect of molybdate addition to chloride
environment on resistance of AISI 316Ti stainless steel to pitting
corrosion was studied. Potentiodynamic polarisation tests were
performed in 1 M and 0.1 M chloride acidified solutions with various
additions of sodium molybdate at room temperature. The presented
results compare the effect of molybdate anions on quality of passive
film (expressed by the pitting potential) in both chloride solutions.
The pitting potential increases with the increase inhibitor
concentration. The inhibitive effect of molybdate ions is stronger in
chloride solution of lower aggressiveness (0.1M).
Abstract: Oxygen Reduction Reaction (ORR) performance of
iron and nitrogen co-doped porous carbon nanoparticles (Fe-NPC)
with various physical and (electro) chemical properties have been
investigated. Fe-NPC nanoparticles are synthesized via a facile
soft-templating procedure by using Iron (III) chloride hexa-hydrate as
iron precursor and aminophenol-formaldehyde resin as both carbon
and nitrogen precursor. Fe-NPC nanoparticles shows high surface area
(443.83 m2g-1), high pore volume (0.52 m3g-1), narrow mesopore size
distribution (ca. 3.8 nm), high conductivity (IG/ID=1.04), high kinetic
limiting current (11.71 mAcm-2) and more positive onset potential
(-0.106 V) compared to metal-free NPC nanoparticles (-0.295V)
which make it high efficient ORR metal-free catalysts in alkaline
solution. This study may pave the way of feasibly designing iron and
nitrogen containing carbon materials (Fe-N-C) for highly efficient
oxygen reduction electro-catalysis.
Abstract: In this paper, relationship between different properties
of IC concrete and water cement ratio, obtained from a
comprehensive experiment conducted on IC using local materials
(Burnt clay chips- BC) is presented. In addition, saturated SAP was
used as an IC material in some cases. Relationships have been
developed through regression analysis. The focus of this analysis is
on developing relationship between a dependent variable and an
independent variable. Different percent replacements of BC and
water cement ratios were used. Compressive strength, modulus of
elasticity, water permeability and chloride permeability were tested
and variations of these parameters were analyzed with respect to
water cement ratio.
Abstract: Chalcopyrite (CuFeS2) is the most common primary
mineral used for the commercial production of copper. The low
dissolution efficiency of chalcopyrite in sulfate media has prevented
an efficient industrial leaching of this mineral in sulfate media. Ferric
ions, bacteria, oxygen and other oxidants have been used as oxidizing
agents in the leaching of chalcopyrite in sulfate and chloride media
under atmospheric or pressure leaching conditions. Two leaching
methods were studied to evaluate chalcopyrite (CuFeS2) dissolution
in acid media. First, the conventional oxidative acid leaching method
was carried out using sulfuric acid (H2SO4) and potassium
dichromate (K2Cr2O7) as oxidant at atmospheric pressure. Second,
microwave-assisted acid leaching was performed using the
microwave accelerated reaction system (MARS) for same reaction
media. Parameters affecting the copper extraction such as leaching
time, leaching temperature, concentration of H2SO4 and
concentration of K2Cr2O7 were investigated. The results of
conventional acid leaching experiments were compared to the
microwave leaching method. It was found that the copper extraction
obtained under high temperature and high concentrations of oxidant
with microwave leaching is higher than those obtained
conventionally. 81% copper extraction was obtained by the
conventional oxidative acid leaching method in 180 min, with the
concentration of 0.3 mol/L K2Cr2O7 in 0.5M H2SO4 at 50 ºC, while
93.5% copper extraction was obtained in 60 min with microwave
leaching method under same conditions.
Abstract: Ceramic Waste Aggregates (CWAs) were made from
electric porcelain insulator wastes supplied from an electric power
company, which were crushed and ground to fine aggregate sizes. In
this study, to develop the CWA mortar as an eco–efficient, ground
granulated blast–furnace slag (GGBS) as a Supplementary
Cementitious Material (SCM) was incorporated. The water–to–binder
ratio (W/B) of the CWA mortars was varied at 0.4, 0.5, and 0.6. The
cement of the CWA mortar was replaced by GGBS at 20 and 40% by
volume (at about 18 and 37% by weight). Mechanical properties of
compressive and splitting tensile strengths, and elastic modulus were
evaluated at the age of 7, 28, and 91 days. Moreover, the chloride
ingress test was carried out on the CWA mortars in a 5.0% NaCl
solution for 48 weeks. The chloride diffusion was assessed by using an
electron probe microanalysis (EPMA). To consider the relation of the
apparent chloride diffusion coefficient and the pore size, the pore size
distribution test was also performed using a mercury intrusion
porosimetry at the same time with the EPMA. The compressive
strength of the CWA mortars with the GGBS was higher than that
without the GGBS at the age of 28 and 91 days. The resistance to the
chloride ingress of the CWA mortar was effective in proportion to the
GGBS replacement level.
Abstract: In this study, nuclear magnetic resonance
spectroscopy and nuclear quadrupole resonance spectroscopy
parameters of 14N (Nitrogen in imidazole ring) in N–H…O hydrogen
bonding for Histidine hydrochloride monohydrate were calculated via
density functional theory. We considered a five-molecule model
system of Histidine hydrochloride monohydrate. Also we examined
the trends of environmental effect on hydrogen bonds as well as
cooperativity. The functional used in this research is M06-2X which
is a good functional and the obtained results has shown good
agreement with experimental data. This functional was applied to
calculate the NMR and NQR parameters. Some correlations among
NBO parameters, NMR and NQR parameters have been studied
which have shown the existence of strong correlations among them.
Furthermore, the geometry optimization has been performed using
M062X/6-31++G(d,p) method. In addition, in order to study
cooperativity and changes in structural parameters, along with
increase in cluster size, natural bond orbitals have been employed.
Abstract: Psyllium gum alone and in combination with
sunflower oil was investigated as a possible alternative edible coating
for improvement of quality and shelf life of fresh-cut papaya.
Different concentrations including 0.5, 1 and 1.5 percent of psyllium
gum were used for coating of fresh-cut papaya. In some samples,
refined sunflower oil was used as a lipid component to increase the
effectiveness of coating in terms of water barrier properties. Soya
lecithin was used as an emulsifier in coatings containing oil.
Pretreatment with 1% calcium chloride was given to maintain the
firmness of fresh-cut papaya cubes. 1% psyllium gum coating was
found to yield better results. Further, addition of oil helped to
maintain the quality and acted as a barrier to water vapour, therefore,
minimizing the weight loss.
Abstract: It is the worldwide problem that the recycled PVB is
not recycled and it is wildly stored in landfills. However, PVB has
similar chemical properties such as PVC. Moreover, both of these
polymers are plasticized. Therefore, the study of thermal properties
of plasticized PVC and the recycled PVB obtained by recycling of
windshields is carried out. This work has done in order to find nondegradable
processing conditions applicable for both polymers.
Tested PVC contained 38% of plasticizer diisononyl phthalate
(DINP) and PVB was plasticized with 28% of triethylene glycol,
bis(2-ethylhexanoate) (3GO). The thermal and thermo-oxidative
decomposition of both vinyl polymers are compared by calorimetric
analysis and by tensile strength analysis.
Abstract: To ensure targeting of apoferritin nanocarrier with
encapsulated doxorubicin drug, we used a peptide linker based on a
protein G with N-terminus affinity towards Fc region of antibodies.
To connect the peptide to the surface of apoferritin, the C-terminus of
peptide was made of cysteine with affinity to gold. The surface of
apoferritin with encapsulated doxorubicin (APODOX) was coated
either with gold nanoparticles (APODOX-Nano) or gold(III) chloride
hydrate reduced with sodium borohydride (APODOX-HAu). The
reduction with sodium borohydride caused a loss of doxorubicin
fluorescent properties and probably accompanied with the loss of its
biological activity. Fluorescent properties of APODOX-Nano were
similar to the unmodified APODOX; therefore it was more suited for
the intended use. To evaluate the specificity of apoferritin modified
with antibodies, ELISA-like method was used with the surface of
microtitration plate wells coated by the antigen (goat anti-human IgG
antibodies). To these wells, the nanocarrier was applied. APODOX
without the modification showed 5× lower affinity to the antigen than
APODOX-Nano modified gold and targeting antibodies (human IgG
antibodies).
Abstract: Advanced treatments such as forward osmosis (FO)
can be used to separate or reject nutrients from secondary treated
effluents. Forward osmosis uses the chemical potential across the
membrane, which is the osmotic pressure gradient, to induce water to
flow through the membrane from a feed solution (FS) into a draw
solution (DS). The performance of FO is affected by the membrane
characteristics, composition of the FS and DS, and operating
conditions. The aim of this study was to investigate the optimum
velocity and temperature for nutrient rejection and water flux
performance in FO treatments. MgCl2 was used as the DS in the FO
process. The results showed that higher cross flow velocities yielded
higher water fluxes. High rejection of nutrients was achieved by using
a moderate cross flow velocity at 0.25 m/s. Nutrient rejection was
insensitive to temperature variation, whereas water flux was
significantly impacted by it. A temperature of 25°C was found to be
good for nutrient rejection.
Abstract: We investigated the structure and electronic properties
of the compound Mg1-xBixO with varying concentrations of 0, ¼, ½,
and ¾ x bismuth in the the cesium chloride (CsCl), zinc-blende
(ZnS), nickel arsenide (NiAs) NaCl (rock-salt) and WZ (wurtzite)
phases. We calculated. The calculations were performed using the
first-principles pseudo-potential method within the framework of spin
density functional theory (DFT).
Abstract: Chrome tannery wastewater causes serious environmental hazard due to its high pollution potential. As a result, rigorous treatment is necessary for abatement of pollution from this type of wastewater. There are many research studies on chrome tannery wastewater treatment in the field of physical, chemical, and biological methods. In general, biological treatment process is found ineffective for direct application because of adverse effects by toxic chromium, sulphide, chloride etc. However, biological methods were employed mainly for a few sub processes generating significant amount of organic matter and without chromium, chlorides etc. In this context the present paper reviews the characteristics feature and pollution potential of wastewater generated from chrome tannery units and treatment of the same. The different biological processes used earlier and their chronological development for treatment of the chrome tannery wastewater are thoroughly reviewed in this paper. In this regard, the scope of hybrid bioreactor - an advanced technology option has also been explored, as this kind of treatment is well suited for the wastewater having inhibitory substances.
Abstract: Forward Osmosis (FO) polyamide thin-film composite
membranes have been prepared by interfacial polymerization using
commercial UF polyethersulfoneas membrane support. Different
interfacial polymerization times (10s, 30s and 60s) in the organic
solution containing trimesoyl chloride (TMC) at constant m-phenylenediamine
(MPD) concentration (2% w/v) were studied. The
synthesized polyamide membranes then tested for treatment of
natural organic matter (NOM) and compared to commercial Cellulose
TriAcetate (CTA) membrane. It was found that membrane prepared
with higher reaction time (30s and 60s) exhibited better membrane
performance (flux and humic acid removal) over commercial CTA
membrane.