Abstract: The effect of concentration of reduction agent of
sodium borohydrate (NaBH4) on the properties of silicon
nanoparticles synthesized via microemulsion route is reported. In
this work, the concentration of the silicon tetrachloride (SiCl4) that
served as silicon source with sodium hydroxide (NaOH) and
polyethylene glycol (PEG) as stabilizer and surfactant, respectively,
are keep fixed. Four samples with varied concentration of NaBH4
from 0.05 M to 0.20 M were synthesized. It was found that the lowest
concentration of NaBH4 gave better formation of silicon
nanoparticles.
Abstract: The proof of concept experiments were conducted to
determine the feasibility of using small amounts of Dissolved
Sulphur (DS) from the gaseous phase to precipitate platinum ions in
chloride media. Two sets of precipitation experiments were
performed in which the source of sulphur atoms was either a
thiosulphate solution (Na2S2O3) or a sulphur dioxide gas (SO2). In
liquid-liquid (L-L) system, complete precipitation of Pt was achieved
at small dosages of Na2S2O3 (0.01 – 1.0 M) in a time interval of 3-5
minutes. On the basis of this result, gas absorption tests were carried
out mainly to achieve sulphur solubility equivalent to 0.018 M. The
idea that huge amounts of precious metals could be recovered
selectively from their dilute solutions by utilizing the waste SO2
streams at low pressure seemed attractive from the economic and
environmental point of views. Therefore, mass transfer characteristics
of SO2 gas associated with reactive absorption across the gas-liquid
(G-L) interface were evaluated under different conditions of pressure
(0.5 – 2 bar), solution temperature ranges from 20 – 50 oC and acid
strength (1 – 4 M, HCl). This paper concludes with information about
selective precipitation of Pt in the presence of cations (Fe2+, Co2+,
and Cr3+) in a CSTR and recommendation to scale up laboratory data
to industrial pilot scale operations.
Abstract: Tomato powder has good potential as substitute of tomato paste and other tomato products. In order to protect physicochemical properties and nutritional quality of tomato during dehydration process, investigation was carried out using different drying methods and pretreatments. Solar drier and continuous conveyor (tunnel) drier were used for dehydration where as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl) selected for treatment.. lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning in addition to moisture, sugar and titrable acidity were studied. Results show that pre-treatment with CaCl2 and NaCl increased water removal and moisture mobility in tomato slices during drying of tomatoes. Where CaCl2 used along with KMS the NEB was recorded the least compared to other treatments and the best results were obtained while using the two chemicals in combination form. Storage studies in LDPE polymeric and metalized polyesters films showed less changes in the products packed in metallized polyester pouches and even after 6 months lycopene content did not decrease more than 20% as compared to the control sample and provide extension of shelf life in acceptable condition for 6 months. In most of the quality characteristics tunnel drier samples presented better values in comparison to solar drier.
Abstract: The manufacturing transmission line tower parts has
being generated hazardous waste which is required proper disposal
of waste for protection of land pollution. Manufacturing Process in
the manufacturing of steel angle, plates, pipes, channels are passes
through conventional, semi automatic and CNC machines for
cutting, marking, punching, drilling, notching, bending operations.
All fabricated material Coated with thin layer of Zinc in Galvanizing
plant where molten zinc is used for coating. Prior to Galvanizing,
chemical like 33% concentrated HCl Acid, ammonium chloride and
d-oil being used for pretreatment of iron. The bath of water with
sodium dichromate is used for cooling and protection of the
galvanized steel. For the heating purpose the furnace oil burners are
used. These above process the Zinc dross, Zinc ash, ETP sludge and
waste pickled acid generated as hazardous waste. The RPG has
made captive secured land fill site, since 1997 since then it was
using for disposal of hazardous waste after completion of SLF
(Secured land fill) site. The RPG has raised height from ground
level then now it is being used for disposal of waste as he designed
the SLF after in creasing height of from GL it is functional without
leach ate or adverse impacts in the environment.
Abstract: The photochemical and photo-Fenton oxidation of 1,3-dichloro-2-propanol was performed in a batch reactor, at room temperature, using UV radiation, H2O2 as oxidant, and Fenton-s reagent. The effect of the oxidative agent-s initial concentration was investigated as well as the effect of the initial concentration of Fe(II) by following the target compound degradation, the total organic carbon removal and the chloride ion production. Also, from the kinetic analysis conducted and proposed reaction scheme it was deduced that the addition of Fe(II) significantly increases the production and the further oxidation of the chlorinated intermediates.
Abstract: The study area receives a wide variety of wastes
generated by municipalities and the industries like paints and
pigments, metal processing industries, thermal power plants electroprocessing
industries etc. The Physico-chemical and structural
investigation of water from river Pandu indicated high level of
chlorides and calcium which made the water unsuitable for human
use. Algae like Cyclotella fumida, Asterionella Formosa,
Cladophora glomerata, Pediastrum simplex, Scenedesmus bijuga,
Cladophora glomerata were the dominant pollution tolerant species
recorded under these conditions. The sensitive and less abundant
species of algae included Spirogyra sps., Merismopedia sps. The
predominance colonies of Zygnema sps, Phormidium sps,
Mycrocystis aeruginosa, Merismopedia minima, Pandorina morum,
seems to correlate with high organic contents of Pandu river water.
This study assumes significance as some algae can be used as
bioindicators of water pollution and algal floral of a municipal drain
carrying waste effluents from industrial area Kanpur and discharge
them into the river Pandu flowing onto southern outskirts of Kanpur
city.
Abstract: In this study, cometabolic biodegradation of
chloroform was experimented with mixed cultures in the presence of
various organic solvents like methanol, ethanol, isopropanol, acetone,
acetonitrile and toluene as these are predominant discharges in
pharmaceutical industries. Toluene and acetone showed higher
specific chloroform degradation rate when compared to other
compounds. Cometabolic degradation of chloroform was further
confirmed by observation of free chloride ions in the medium. An
extended Haldane model, incorporating the inhibition due to
chloroform and the competitive inhibition between primary
substrates, was developed to predict the biodegradation of primary
substrates, cometabolic degradation of chloroform and the biomass
growth. The proposed model is based on the use of biokinetic
parameters obtained from single substrate degradation studies. The
model was able to satisfactorily predict the experimental results of
ternary and quaternary mixtures. The proposed model can be used for
predicting the performance of bioreactors treating discharges from
pharmaceutical industries.
Abstract: In this study, a new procedure for inspecting damages on LNG storage tanks was proposed with the use of structural diagnostic techniques: i.e., nondestructive inspection techniques such as macrography, the hammer sounding test, the Schmidt hammer test, and the ultrasonic pulse velocity test, and destructive inspection techniques such as the compressive strength test, the chloride penetration test, and the carbonation test. From the analysis of all the test results, it was concluded that the LNG storage tank cover was in good condition. Such results were also compared with the Korean concrete standard specifications and design values. In addition, the remaining life of the LNG storage tank was estimated by using existing models. Based on the results, an LNG storage tank cover performance evaluation procedure was suggested.
Abstract: In this paper, we have focused on study of swelling kinetics and salt-sensitivity behavior of a superabsorbing hydrogel based on carboxymethylcellulose (CMC) and acrylic acid and 2- Buthyl methacrylate. The swelling kinetics of the hydrogels with various particle sizes was preliminary investigated as well. The swelling of the hydrogel showed a second order kinetics of swelling in water. In addition, swelling measurements of the synthesized hydrogels in various chloride salt solutions was measured. Results indicated that a swelling-loss with an increase in the ionic strength of the salt solutions.
Abstract: To decompose organochlorides by bioremediation, co-culture biohydrogen producer and dehalogenation microorganisms is a useful method. In this study, we combined these two characteristics from a biohydrogen producer, Rhodopseudomonas palustris, and a dehalogenation microorganism, Pseudomonas putida, to enchance halorespiration in R. palustris. The genes encoding cytochrome P450cam system (camC, camA, and camB) from P. putida were expressed in R. palustris with designated expression plasmid. All tested strains were cultured to log phase then presented pentachloroethane (PCA) in media. The vector control strain could degrade PCA about 78% after 16 hours, however, the cytochrome P450cam system expressed strain, CGA-camCAB, could completely degrade PCA in 12 hours. While taking chlorinated aromatic, 3-chlorobenzoate, as sole carbon source or present benzoate as co-substrate, CGA-camCAB presented faster growth rate than vector control strain.
Abstract: A microchannel with two inlets and two outlets was tested as a potential reactor to carry out two-phase catalytic phase transfer reaction with phase separation at the exit of the microchannel. The catalytic phase transfer reaction between benzyl chloride and sodium sulfide was chosen as a model reaction. The effect of operational time on the conversion was studied. By utilizing a multiphase parallel flow inside the microchannel reactor with the aid of a guideline structure, the catalytic phase reaction followed by phase separation could be ensured. The organic phase could be separated completely from one exit and part of the aqueous phase was separated purely and could be reused with slightly affecting the catalytic phase transfer reaction.
Abstract: A spectrophotometric method was developed for simultaneous quantification of pseudoephedrine hydrochloride (PSE) triprolidine hydrochloride (TRI) using second derivative method (zero-crossing technique). The second derivative amplitudes of PSE and TRI were measured at 271 and 321 nm, respectively. The calibration curves were linear in the range of 200 to 1,000 g/ml for PSE and 10 to 50 g/ml for TRI. The method was validated for specificity, accuracy, precision, limit of detection and limit of quantitation. The proposed method was applied to the assaying and dissolution of PSE and TRI in commercial tablets without any chemical separation. The results were compared with those obtained by the official USP31 method and statistical tests showed that there is no significant between the methods at 95% confidence level. The proposed method is simple, rapid and suitable for the routine quality control application. KeywordsTriprolidine, Pseudoephedrine, Derivative spectrophotometry, Dissolution testing.
Abstract: All around the world pulp and paper industries are the
biggest plant production with the environmental pollution as the
biggest challenge facing the pulp manufacturing operations. The
concern among these industries is to produce a high volume of papers
with the high quality standard and of low cost without affecting the
environment. This result obtained from this bleaching study show
that the activation of peroxide was an effective method of reducing
the total applied charge of chlorine dioxide which is harmful to our
environment and also show that softwood and hardwood Kraft pulps
responded linearly to the peroxide treatments. During the bleaching
process the production plant produce chlorines. Under the trial stages
chloride dioxide has been reduced by 3 kg/ton to reduce the
brightness from 65% ISO to 60% ISO of pulp and the dosing point
returned to the E stage charges by pre-treating Kraft pulps with
hydrogen peroxide. The pulp and paper industry has developed
elemental chlorine free (ECF) and totally chlorine free (TCF)
bleaching, in their quest for being environmental friendly, they have
been looking at ways to turn their ECF process into a TCF process
while still being competitive. This prompted the research to
investigate the capability of the hydrogen peroxide as catalyst to
reduce chloride dioxide.
Abstract: Chlorine is one of the most abundant elements in
nature, which undergoes a complex biogeochemical cycle. Chlorine
bound in some substances is partly responsible for atmospheric ozone
depletion and contamination of some ecosystems. As due to
international regulations anthropogenic burden of volatile
organochlorines (VOCls) in atmosphere decreases, natural sources
(plants, soil, abiotic formation) are expected to dominate VOCl
production in the near future. Examples of plant VOCl production are
methyl chloride, and bromide emission from (sub)tropical ferns,
chloroform, 1,1,1-trichloroethane and tetrachloromethane emission
from temperate forest fern and moss. Temperate forests are found to
emit in addition to the previous compounds tetrachloroethene, and
brominated volatile compounds. VOCls can be taken up and further
metabolized in plants. The aim of this work is to identify and
quantitatively analyze the formed VOCls in temperate forest
ecosystems by a cryofocusing/GC-ECD detection method, hence
filling a gap of knowledge in the biogeochemical cycle of chlorine.
Abstract: The aim of this in vitro study was to evaluate the possible interference of a Nectandra membranacea extract (i) on the labeling of blood cells (BC), (ii) on the labeling process of BC and plasma (P) proteins with technetium-99m (Tc-99m) and (iii) on the morphology of red blood cells (RBC). Blood samples were incubated with a Nectandra membranacea crude extract, stannous chloride, Tc- 99m (sodium pertechnetate) was added, and soluble (SF) and insoluble (IF) fractions were isolated. Morphometry studies were performed with blood samples incubated with Nectandra membranacea extract. The results show that the Nectandra membranacea extract does not promote significant alteration of the labeling of BC, IF-P and IF-BC. The Nectandra membranacea extract was able to alter the erythrocyte membrane morphology, but these morphological changes were not capable to interfere on the labeling of blood constituents with Tc-99m.
Abstract: Wood pyrolysis for Casuarina glauca, Casuarina cunninghamiana, Eucalyptus camaldulensis, Eucalyptus microtheca was made at 450°C with 2.5°C/min. in a flowing N2-atmosphere. The Eucalyptus genus wood gave higher values of specific gravity, ash , total extractives, lignin, N2-liquid trap distillate (NLTD) and water trap distillate (WSP) than those for Casuarina genus. The GHC of NLTD was higher for Casuarina genus than that for Eucalyptus genus with the highest value for Casuarina cunninghamiana. Guiacol, 4-ethyl-2-methoxyphenol and syringol were observed in the NLTD of all the four wood species reflecting their parent hardwood lignin origin. Eucalyptus camaldulensis wood had the highest lignin content (28.89%) and was pyrolyzed to the highest values of phenolics (73.01%), guaiacol (11.2%) and syringol (32.28%) contents in methylene chloride fraction (MCF) of NLTD. Accordingly, recoveries of syringol and guaiacol may become economically attractive from Eucalyptus camaldulensis.
Abstract: Mercury is a natural occurring element and present in
various concentrations in the environment. Due to its toxic effects, it
is desirable to research mercury sensitive materials to adsorb
mercury. This paper describes the preparation of Au nanoparticles for
mercury adsorption by using a microwave (MW)-polyol method in
the presence of three different Sodium Chloride (NaCl)
concentrations (10, 20 and 30 mM). Mixtures of spherical, triangular,
octahedral, decahedral particles and 1-D product were obtained using
this rapid method. Sizes and shapes was found strongly depend on the
concentrations of NaCl. Without NaCl concentration, spherical,
triangular plates, octahedral, decahedral nanoparticles and 1D
product were produced. At the lower NaCl concentration (10 mM),
spherical, octahedral and decahedral nanoparticles were present,
while spherical and decahedral nanoparticles were preferentially form
by using 20 mM of NaCl concentration. Spherical, triangular plates,
octahedral and decahedral nanoparticles were obtained at the highest
NaCl concentration (30 mM). The amount of mercury adsorbed using
20 ppm mercury solution is the highest (67.5 %) for NaCl
concentration of 30 mM. The high yield of polygonal particles will
increase the mercury adsorption. In addition, the adsorption of
mercury is also due to the sizes of the particles. The sizes of particles
become smaller with increasing NaCl concentrations (size ranges, 5-
16 nm) than those synthesized without addition of NaCl (size ranges
11-32 nm). It is concluded that NaCl concentrations affects the
formation of sizes and shapes of Au nanoparticles thus affects the
mercury adsorption.
Abstract: In this study, solid phase micro-extraction (SPME)
was optimized to improve the sensitivity and accuracy in
formaldehyde determination for plywood panels. Further work has
been carried out to compare the newly developed technique with
existing method which reacts formaldehyde collected in desiccators
with acetyl acetone reagent (DC-AA). In SPME, formaldehyde was
first derivatized with O-(2,3,4,5,6 pentafluorobenzyl)-hydroxylamine
hydrochloride (PFBHA) and analysis was then performed by gas
chromatography in combination with mass spectrometry (GC-MS).
SPME data subjected to various wood species gave satisfactory
results, with relative standard deviations (RSDs) obtained in the
range of 3.1-10.3%. It was also well correlated with DC values,
giving a correlation coefficient, RSQ, of 0.959. The quantitative
analysis of formaldehyde by SPME was an alternative in wood
industry with great potential
Abstract: The mechanical properties of blends consisting of
plasticized poly(vinyl butyral) (PVB) and plasticized poly(vinyl
chloride) (PVC) are studied, in order to evaluate the possibility of
using recycled PVB waste derived from windshields. PVC was
plasticized with 38% of diisononyl phthalate (DINP), while PVB was
plasticized with 28% of triethylene glycol, bis(2-ethylhexanoate)
(3GO). The optimal process conditions for the PVB/PVC blend in 1:1
ratio were determined. Entropy was used in order to theoretically
predict the blends miscibility. The PVB content of each blend
composition used was ranging from zero to 100%. Tensile strength
and strain were tested. In addition, a comparison between recycled
and original PVB, used as constituents of the blend, was performed.
Abstract: Sampling and analysis of leachate from Bhalaswa
landfill and groundwater samples from nearby locations, clearly
indicated the likely contamination of groundwater due to landfill
leachate. The results of simulation studies carried out for the
migration of Chloride from landfill shows that the simulation results
are in consonance with the observed concentration of Chloride in the
vicinity of landfill facility. The solid waste disposal system presently
being practiced in Delhi consists of mere dumping of wastes
generated, at three locations Bhalaswa, Ghazipur, and Okhla without
any regard to proper care for the protection of surrounding
environment. Bhalaswa landfill site in Delhi, which is being operated
as a dump site, is expected to become cause of serious groundwater
pollution in its vicinity. The leachate from Bhalaswa landfill was
found to be having a high concentration of chlorides, as well as DOC,
COD. The present study was undertaken to determine the likely
concentrations of principle contaminants in the groundwater over a
period of time due to the discharge of such contaminants from
landfill leachates to the underlying groundwater. The observed
concentration of chlorides in the groundwater within 75m of the
radius of landfill facility was found to be in consonance with the
simulated concentration of chloride in groundwater considering one
dimensional transport model, with finite mass of contaminant source.
Governing equation of contaminant transport involving advection and
diffusion-dispersion was solved in matlab7.0 using finite difference
method.