Abstract: A new OTA-based logarithmic-control variable gain
current amplifier (LCCA) is presented. It consists of two Operational
Transconductance Amplifier (OTA) and two PMOS transistors
biased in weak inversion region. The circuit operates from 0.6V DC
power supply and consumes 0.6 μW. The linear-dB controllable
output range is 43 dB with maximum error less than 0.5dB. The
functionality of the proposed design was confirmed using HSPICE in
0.35μm CMOS process technology.
Abstract: A 3.5-bit stage of the CMOS pipelined ADC is proposed. In this report, the main part of 3.5-bit stage ADC is introduced. How the MDAC, comparator and encoder worked and designed are shown in details. Besides, an OTA which is used in fully differential pipelined ADC was described. Using gain-boost architecture with differential amplifier, this OTA achieve high-gain and high-speed. This design was using CMOS 0.18um process and simulation in Cadence. The result of the simulation shows that the OTA has a gain up to 80dB, the unity gain bandwidth of about 1.138GHz with 2pF load.
Abstract: Pipeline ADCs are becoming popular at high speeds
and with high resolution. This paper discusses the options of number
of bits/stage conversion techniques in pipelined ADCs and their
effect on Area, Speed, Power Dissipation and Linearity. The basic
building blocks like op-amp, Sample and Hold Circuit, sub converter,
DAC, Residue Amplifier used in every stage is assumed to be
identical. The sub converters use flash architectures. The design is
implemented using 0.18
Abstract: This paper describes the design of a voltage based maximum power point tracker (MPPT) for photovoltaic (PV) applications. Of the various MPPT methods, the voltage based method is considered to be the simplest and cost effective. The major disadvantage of this method is that the PV array is disconnected from the load for the sampling of its open circuit voltage, which inevitably results in power loss. Another disadvantage, in case of rapid irradiance variation, is that if the duration between two successive samplings, called the sampling period, is too long there is a considerable loss. This is because the output voltage of the PV array follows the unchanged reference during one sampling period. Once a maximum power point (MPP) is tracked and a change in irradiation occurs between two successive samplings, then the new MPP is not tracked until the next sampling of the PV array voltage. This paper proposes an MPPT circuit in which the sampling interval of the PV array voltage, and the sampling period have been shortened. The sample and hold circuit has also been simplified. The proposed circuit does not utilize a microcontroller or a digital signal processor and is thus suitable for low cost and low power applications.
Abstract: This article presents a current-mode universal biquadratic filter. The proposed circuit can apparently provide standard functions of the biquad filter: low-pass, high-pass, bandpass, band-reject and all-pass functions. The circuit uses 4 current controlled transconductance amplifiers (CCTAs) and 2 grounded capacitors. In addition, the pole frequency and quality factor can be adjusted by electronic method by adjusting the bias currents of the CCTA. The proposed circuit uses only grounded capacitors without additional external resistors, the proposed circuit is considerably appropriate to further developing into an integrated circuit. The results of PSPICE simulation program are corresponding to the theoretical analysis.
Abstract: In recent years Operational Transconductance Amplifier based high frequency integrated circuits, filters and systems have been widely investigated. The usefulness of OTAs over conventional OP-Amps in the design of both first order and second order active filters are well documented. This paper discusses some of the tunability issues using the Matlab/Simulink® software which are previously unreported for any commercial OTA. Using the simulation results two first order voltage controlled all pass filters with phase tuning capability are proposed.
Abstract: In this paper, a frequency-variation based method has
been proposed for transistor parameter estimation in a commonemitter
transistor amplifier circuit. We design an algorithm to estimate
the transistor parameters, based on noisy measurements of the output
voltage when the input voltage is a sine wave of variable frequency
and constant amplitude. The common emitter amplifier circuit has
been modelled using the transistor Ebers-Moll equations and the
perturbation technique has been used for separating the linear and
nonlinear parts of the Ebers-Moll equations. This model of the amplifier
has been used to determine the amplitude of the output sinusoid as
a function of the frequency and the parameter vector. Then, applying
the proposed method to the frequency components, the transistor
parameters have been estimated. As compared to the conventional
time-domain least squares method, the proposed method requires
much less data storage and it results in more accurate parameter
estimation, as it exploits the information in the time and frequency
domain, simultaneously. The proposed method can be utilized for
parameter estimation of an analog device in its operating range of
frequencies, as it uses data collected from different frequencies output
signals for parameter estimation.
Abstract: In this paper we present a linear autozeroing ultra lowvoltage amplifier. The autozeroing performed by all ULV circuits is important to reduce the impact of noise and especially avoid power supply noise in mixed signal low-voltage CMOS circuits. The simulated data presented is relevant for a 90nm TSMC CMOS process.
Abstract: In this paper, the gain spectrum of EDFA has been broadened by implementing HTE configuration for S and C band. On using this configuration an amplification bandwidth of 76nm ranging from 1479nm to 1555nm with a peak gain of 26dB has been obtained.
Abstract: This paper describes the gain and noise performances
of discrete Raman amplifier as a function of fiber lengths and the
signal input powers for different pump configurations. Simulation has
been done by using optisystem 7.0 software simulation at signal
wavelength of 1550 nm and a pump wavelength of 1450nm. The
results showed that the gain is higher in bidirectional pumping than in
counter pumping, the gain changes with increasing the fiber length
while the noise figure remain the same for short fiber lengths and the
gain saturates differently for different pumping configuration at
different fiber lengths and power levels of the signal.
Abstract: A novel circuit for generating a signal embedded with
features about data from three sensors is presented. This suggested
circuit is making use of a resistance-to-time converter employing a
bridge amplifier, an integrator and a comparator. The second resistive
sensor (Rz) is transformed into duty cycle. Another bridge with
varying resistor, (Ry) in the feedback of an OP AMP is added in
series to change the amplitude of the resulting signal in a proportional
relationship while keeping the same frequency and duty cycle
representing proportional changes in resistors Rx and Rz already
mentioned. The resultant output signal carries three types of
information embedded as variations of its frequency, duty cycle and
amplitude.
Abstract: In this paper, we analyze the effect of noise in a single- ended input differential amplifier working at high frequencies. Both extrinsic and intrinsic noise are analyzed using time domain method employing techniques from stochastic calculus. Stochastic differential equations are used to obtain autocorrelation functions of the output noise voltage and other solution statistics like mean and variance. The analysis leads to important design implications and suggests changes in the device parameters for improved noise characteristics of the differential amplifier.
Abstract: An active RC filters with a 880 / 1760 MHz dual bandwidth tuning ability is present for 60 GHz unlicensed band applications. A third order Butterworth low-pass filter utilizes two Cherry-Hooper amplifiers to satisfy the very high bandwidth requirements of an amplifier. The low-pass filter is fabricated in 90nm standard CMOS process. Drawing 6.7 mW from 1.2 V power supply, the low frequency gains of the filter are -2.5 and -4.1 dB, and the output third order intercept points (OIP3) are +2.2 and +1.9 dBm for the single channel and channel bonding conditions, respectively.
Abstract: Small cracks or chips of a product appear very
frequently in the course of continuous production of an automatic
press process system. These phenomena become the cause of not only
defective product but also damage of a press mold. In order to solve
this problem AE system was introduced. AE system was expected to
be very effective to real time detection of the defective product and to
prevention of the damage of the press molds.
In this study, for pick and analysis of AE signals generated from the
press process, AE sensors/pre-amplifier/analysis and processing board
were used as frequently found in the other similar cases. For analysis
and processing the AE signals picked in real time from the good or bad
products, specialized software called cdm8 was used. As a result of
this work it was conformed that intensity and shape of the various AE
signals differ depending on the weight and thickness of metal sheet
and process type.
Abstract: This paper presents an optimized methodology to
folded cascode operational transconductance amplifier (OTA) design.
The design is done in different regions of operation, weak inversion,
strong inversion and moderate inversion using the gm/ID methodology
in order to optimize MOS transistor sizing.
Using 0.35μm CMOS process, the designed folded cascode OTA
achieves a DC gain of 77.5dB and a unity-gain frequency of 430MHz
in strong inversion mode. In moderate inversion mode, it has a 92dB
DC gain and provides a gain bandwidth product of around 69MHz.
The OTA circuit has a DC gain of 75.5dB and unity-gain frequency
limited to 19.14MHZ in weak inversion region.
Abstract: This article proposes a voltage-mode
multifunction filter using differential voltage current
controllable current conveyor transconductance amplifier
(DV-CCCCTA). The features of the circuit are that: the
quality factor and pole frequency can be tuned independently
via the values of capacitors: the circuit description is very
simple, consisting of merely 1 DV-CCCCTA, and 2
capacitors. Without any component matching conditions, the
proposed circuit is very appropriate to further develop into
an integrated circuit. Additionally, each function response
can be selected by suitably selecting input signals with
digital method. The PSpice simulation results are depicted.
The given results agree well with the theoretical anticipation.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: For gamma radiation detection, assemblies having
scintillation crystals and a photomultiplier tube, also there is a
preamplifier connected to the detector because the signals from
photomultiplier tube are of small amplitude. After pre-amplification
the signals are sent to the amplifier and then to the multichannel
analyser. The multichannel analyser sorts all incoming electrical
signals according to their amplitudes and sorts the detected photons
in channels covering small energy intervals. The energy range of
each channel depends on the gain settings of the multichannel
analyser and the high voltage across the photomultiplier tube. The
exit spectrum data of the two main isotopes studied ,putting data in
biomass program ,process it by Matlab program to get the solid
holdup image (solid spherical nuclear fuel)
Abstract: An implementation of current-mode multiphase sinusoidal oscillators is presented. Using CFTA-based lossy integrators, odd and odd/even phase systems can be realized with following advantages. The condition of oscillation and frequency of oscillation can be orthogonally tuned. The high output impedances facilitate easy driving an external load without additional current buffers. The proposed MSOs provide odd or even phase signals that are equally spaced in phase and equal amplitude. The circuit requires one CFTA, one resistor and one grounded capacitor per phase without additional current amplifier. The results of PSPICE simulations using CMOS CFTA are included to verify theory.