Abstract: Xanthan gum is one of the major commercial
biopolymers. Due to its excellent rheological properties xanthan gum
is used in many applications, mainly in food industry. Commercial
production of xanthan gum uses glucose as the carbon substrate;
consequently the price of xanthan production is high. One of the
ways to decrease xanthan price, is using cheaper substrate like
agricultural wastes. Iran is one of the biggest date producer countries.
However approximately 50% of date production is wasted annually.
The goal of this study is to produce xanthan gum from waste date
using Xanthomonas campestris PTCC1473 by submerged
fermentation. In this study the effect of three variables including
phosphor and nitrogen amount and agitation rate in three levels using
response surface methodology (RSM) has been studied. Results
achieved from statistical analysis Design Expert 7.0.0 software
showed that xanthan increased with increasing level of phosphor.
Low level of nitrogen leaded to higher xanthan production. Xanthan
amount, increasing agitation had positive influence. The statistical
model identified the optimum conditions nitrogen amount=3.15g/l,
phosphor amount=5.03 g/l and agitation=394.8 rpm for xanthan. To
model validation, experiments in optimum conditions for xanthan
gum were carried out. The mean of result for xanthan was 6.72±0.26.
The result was closed to the predicted value by using RSM.
Abstract: The objectif of the present work is to determinate the
potential of the solar parabolic trough collector (PTC) for use in the
design of a solar thermal power plant in Algeria. The study is based
on a mathematical modeling of the PTC. Heat balance has been
established respectively on the heat transfer fluid (HTF), the absorber
tube and the glass envelop using the principle of energy conservation
at each surface of the HCE cross-sectionn. The modified Euler
method is used to solve the obtained differential equations. At first
the results for typical days of two seasons the thermal behavior of the
HTF, the absorber and the envelope are obtained. Then to determine
the thermal performances of the heat transfer fluid, different oils are
considered and their temperature and heat gain evolutions compared.
Abstract: End milling process is one of the common metal
cutting operations used for machining parts in manufacturing
industry. It is usually performed at the final stage in manufacturing a
product and surface roughness of the produced job plays an
important role. In general, the surface roughness affects wear
resistance, ductility, tensile, fatigue strength, etc., for machined parts
and cannot be neglected in design. In the present work an
experimental investigation of end milling of aluminium alloy with
carbide tool is carried out and the effect of different cutting
parameters on the response are studied with three-dimensional
surface plots. An artificial neural network (ANN) is used to establish
the relationship between the surface roughness and the input cutting
parameters (i.e., spindle speed, feed, and depth of cut). The Matlab
ANN toolbox works on feed forward back propagation algorithm is
used for modeling purpose. 3-12-1 network structure having
minimum average prediction error found as best network architecture
for predicting surface roughness value. The network predicts surface
roughness for unseen data and found that the result/prediction is
better. For desired surface finish of the component to be produced
there are many different combination of cutting parameters are
available. The optimum cutting parameter for obtaining desired
surface finish, to maximize tool life is predicted. The methodology is
demonstrated, number of problems are solved and algorithm is coded
in Matlab®.
Abstract: This study was aimed to explain the influence of surface roughness of the drawbead on non-symmetry deep drawing cold rolled steel sheet to improve the drawability of cold rolled steel sheet. The variables used in this study included semi-circle drawbead with 3 levels of surface roughness which are 6.127 mm Ra, 0.963 mm Ra and 0.152 mm Ra and cold rolled steel sheet according to 3 grades of the JIS standards which are SPCC, SPCE and SPCD with the thickness of 1.0 mm and the blankholder force which is 50% of the drawing force and the depth of 50 mm. According to the test results, when there was the increase in the surface roughness of drawbead, there would be the increase in deep drawing force, especially the SPCC cold rolled steel sheet. This is similar to the increase in the equivalent strain and the wall thickness distribution when the surface roughness of the drawbead increased. It could be concluded that the surface roughness of drawbead has an influence on deep drawing cold rolled steel sheet, especially the drawing force, the equivalent strain and the wall thickness distribution.
Abstract: A four element prototype phased array surface probe
has been designed and constructed to improve clinical human
prostate spectroscopic data. The probe consists of two pairs of
adjacent rectangular coils with an optimum overlap to reduce the
mutual inductance. The two pairs are positioned on the anterior and
the posterior pelvic region and two couples of varactors at the input
of each coil undertake the procedures of tuning and matching. The
probe switches off and on automatically during the consecutive
phases of the MR experiment with the use of an analog switch that is
triggered by a microcontroller. Experimental tests that were carried
out resulted in high levels of tuning accuracy. Also, the switching
mechanism functions properly for various applied loads and pulse
sequence characteristics, producing only 10 μs of latency.
Abstract: Oxygen and carbon isotopes records of multi-species planktonic, benthic foraminifera and bulk carbonate sample from Central Java Indonesia demonstrate that warm sea surface temperature occurred during the Miocene. Planktonic δ18O values from this study consistently lighter (-4 to -3 ‰PDB) than previous studies that indicate sea surface temperature during Miocene in this area was warm than tropical/equatorial localities. A surprising decrease of oxygen isotopic composition was recorded at ±14 Ma where the maximum of δ18O values is -4.87 ‰PDB for Orbulina universa, -5.02 ‰PDB for Globigerinoides sacculifer and -4.30 ‰PDB for Globoquadrina dehiscens, this event we predict as Middle Miocene Optimum. Warming of sea surface temperature we interpret as related to the development of Western Pacific Warm Pool where warm water from Pacific Ocean through the Indonesian seaway appears to remain during Miocene. Our result also show increasing suddenly of oxygen isotope values of planktic, benthic and bulk carbonate sample from ± 12 Ma, the increasing cooled surface water relatively high degree with Late Miocene global cooling climate or we predict that due to closing of Indonesian Gateway.
Abstract: Gold coated silica core nanoparticles have an optical
response dictated by the plasmon resonance. The wavelength at
which the resonance occurs depends on the core and shell sizes,
allowing nanoshells to be tailored for particular applications. The
purposes of this study was to synthesize and use different
concentration of gold nanoshells as exogenous material for skin
tissue soldering and also to examine the effect of laser soldering
parameters on the properties of repaired skin. Two mixtures of
albumin solder and different concentration of gold nanoshells were
prepared. A full thickness incision of 2×20 mm2 was made on the
surface and after addition of mixtures it was irradiated by an 810nm
diode laser at different power densities. The changes of tensile
strength σt due to temperature rise, number of scan (Ns), and scan
velocity (Vs) were investigated. The results showed at constant laser
power density (I), σt of repaired incisions increases by increasing the
concentration of gold nanoshells, Ns and decreasing Vs. It is therefore
important to consider the trade off between the scan velocity and the
surface temperature for achieving an optimum operating condition. In
our case this corresponds to σt =1610 gr/cm2 at I~ 60 Wcm-2, T ~
65ºC, Ns =10 and Vs=0.2mms-1.
Abstract: This paper presents the experimental results of silicone rubber outdoor polymer insulators in salt fog ageing test based on IEC 61109. Specimens made ofHTV silicone rubber with ATH content having three different configurations, straight shedsalternated sheds, and incline and alternate sheds, were tested continuously 1000 hrs.in artificial salt fog chamber. Contamination level, reduction of hydrophobicity and hardness measurement were used as physical damaged inspection techniques to evaluate degree of surface deterioration. In addition, chemical changing of tested specimen surface was evaluated by ATR-FTIRto confirm physical damaged inspection. After 1000 hrs.of salt fog test, differences in degree of surface deterioration were observed on all tested specimens. Physical damaged inspection and chemical analysis results confirmed the experimental results as well.
Abstract: This paper presents an optimization of the hull
separation, i.e. transverse clearance. The main objective is to identify
the feasible speed ranges and find the optimum transverse clearance
considering the minimum wave-making resistance. The dimensions
and the weight of hardware systems installed in the catamaran
structured fuel cell powered USV (Unmanned Surface Vehicle) were
considered as constraints. As the CAE (Computer Aided Engineering)
platform FRIENDSHIP-Framework was used. The hull surface
modeling, DoE (Design of Experiment), Tangent search optimization,
tool integration and the process automation were performed by
FRIENDSHIP-Framework. The hydrodynamic result was evaluated
by XPAN the potential solver of SHIPFLOW.
Abstract: Many applications require surface modification and
micro-structuring of polymers. For these purposes is mainly used
ultraviolet (UV) radiation from excimer lamps or excimer lasers.
However, these sources have a decided disadvantage - degrading the
polymer deep inside due to relatively big radiation penetration depth
which may exceed 100 μm. In contrast, extreme ultraviolet (EUV)
radiation is absorbed in a layer approximately 100 nm thick only. In
this work, the radiation from a discharge-plasma EUV source (with
wavelength 46.9 nm) based on a capillary discharge driver is focused
with a spherical Si/Sc multilayer mirror for surface modification of
PMMA sample or thin gold layer (thickness about 40 nm). It was
found that the focused EUV laser beam is capable by one shot to
ablate PMMA or layer of gold, even if the focus is significantly
influenced by astigmatism.
Abstract: The present study is concerned with effect of exciting
boundary layer on increase in heat transfer from flat surfaces. As any
increase in heat transfer between a fluid inside a face and another one
outside of it can cause an increase in some equipment's efficiency, so
at this present we have tried to increase the wall's heat transfer
coefficient by exciting the fluid boundary layer. By a collision
between flow and the placed block at the fluid way, the flow pattern
and the boundary layer stability will change. The flow way inside the
channel is simulated as a 2&3-dimensional channel by Gambit
TM
software.
With studying the achieved results by this simulation for the flow
way inside the channel with a block coordinating with Fluent
TM
software, it's determined that the figure and dimensions of the exciter
are too important for exciting the boundary layer so that any increase
in block dimensions in vertical side against the flow and any
reduction in its dimensions at the flow side can increase the average
heat transfer coefficient from flat surface and increase the flow
pressure loss. Using 2&3-dimensional analysis on exciting the flow at
the flow way inside a channel by cylindrical block at the same time
with the external flow, we came to this conclusion that the heat flux
transferred from the surface, is increased considerably in terms of the
condition without excitation. Also, the k-e turbulence model is used.
Abstract: Oxidative stress makes up common incidents in
eukaryotic metabolism. The presence of diverse components
disturbing the equilibrium during oxygen metabolism increases
oxidative damage unspecifically in living cells. Body´s own
ubiquinone (Q10) seems to be a promising drug in defending the
heightened appearance of reactive oxygen species (ROS). Though, its
lipophilic properties require a new strategy in drug formulation to
overcome their low bioavailability. Consequently, the manufacture of
heterogeneous nanodispersions is in focus for medical applications.
The composition of conventional nanodispersions is made up of a
drug-consisting core and a surfactive agent, also named as surfactant.
Long-termed encapsulation of the surfactive components into tissues
might be the consequence of the use during medical therapeutics. The
potential of provoking side-effects is given by their nonbiodegradable
properties. Further improvements during fabrication
process use the incorporation of biodegradable components such as
modified γ-polyglutamic acid which decreases the potential of
prospective side-effects.
Abstract: Lanthanide-doped upconversion nanoparticles which can convert near-infrared lights to visible lights have attracted growing interest because of their great potentials in fluorescence imaging. Upconversion fluorescence imaging technique with excitation in the near-infrared (NIR) region has been used for imaging of biological cells and tissues. However, improving the detection sensitivity and decreasing the absorption and scattering in biological tissues are as yet unresolved problems. In this present study, a novel NIR-reflected multispectral imaging system was developed for upconversion fluorescent imaging in small animals. Based on this system, we have obtained the high contrast images without the autofluorescence when biocompatible UCPs were injected near the body surface or deeply into the tissue. Furthermore, we have extracted respective spectra of the upconversion fluorescence and relatively quantify the fluorescence intensity with the multispectral analysis. To our knowledge, this is the first time to analyze and quantify the upconversion fluorescence in the small animal imaging.
Abstract: Protection and proper management of archaeological heritage are an essential process of studying and interpreting the generations present and future. Protecting the archaeological heritage is based upon multidiscipline professional collaboration. This study aims to gather data by different sources (Photogrammetry and Geographic Information System (GIS)) integrated for the purpose of documenting one the of significant archeological sites (Ahl-Alkahf, Jordan). 3D modeling deals with the actual image of the features, shapes and texture to represent reality as realistically as possible by using texture. The 3D coordinates that result of the photogrammetric adjustment procedures are used to create 3D-models of the study area. Adding Textures to the 3D-models surfaces gives a 'real world' appearance to the displayed models. GIS system combined all data, including boundary maps, indicating the location of archeological sites, transportation layer, digital elevation model and orthoimages. For realistic representation of the study area, 3D - GIS model prepared, where efficient generation, management and visualization of such special data can be achieved.
Abstract: Nuclear energy sources have been widely used in the
past decades in order to power spacecraft subsystems. Nevertheless,
their use has attracted controversy because of the risk of harmful
material released into the atmosphere if an accident were to occur
during the launch phase of the mission, leading to the general
adoption of photovoltaic systems.
As compared to solar cells, wind turbines have a great advantage
on Mars, as they can continuously produce power both during dust
storms and at night-time: this paper focuses on the potential of a wind
energy conversion system (WECS) considering the atmospheric
conditions on Mars. Wind potential on Martian surface has been
estimated, as well as the average energy requirements of a Martian
probe or surface rover. Finally, the expected daily energy output of
the WECS has been computed on the basis of both the swept area of
the rotor and the equivalent wind speed at the landing site.
Abstract: Electromyography (EMG) is the study of muscles function through analysis of electrical activity produced from muscles. This electrical activity which is displayed in the form of signal is the result of neuromuscular activation associated with muscle contraction. The most common techniques of EMG signal recording are by using surface and needle/wire electrode where the latter is usually used for interest in deep muscle. This paper will focus on surface electromyogram (SEMG) signal. During SEMG recording, several problems had to been countered such as noise, motion artifact and signal instability. Thus, various signal processing techniques had been implemented to produce a reliable signal for analysis. SEMG signal finds broad application particularly in biomedical field. It had been analyzed and studied for various interests such as neuromuscular disease, enhancement of muscular function and human-computer interface.
Abstract: The nature of adsorbed species on catalytic surface
over an industrial precipitated iron-based high temperature catalyst
during FTS was investigated by in-situ DRIFTS and chemical
trapping. The formulation of the mechanism of oxygenates formation
and key intermediates were also discussed. Numerous oxygenated
precursors and crucial intermediates were found by in-situ DRIFTS,
such as surface acetate, acetyl and methoxide. The results showed that
adsorbed molecules on surface such as methanol or acetaldehyde
could react with basic sites such as lattice oxygen or free surface
hydroxyls. Adsorbed molecules also had reactivity of oxidizing.
Moreover, acetyl as a key intermediate for oxygenates was observed
by investigation of CH3OH + CO and CH3I + CO + H2. Based on the
nature of surface properties, the mechanism of oxygenates formation
on precipitated iron-based high temperature catalyst was discussed.
Abstract: The paper relates to a catalyst, comprising copperchromium
spinel, coated on carrier γ-Al2O3. The effect of preparation
conditions on the active component composition and activity
behavior of the catalysts is discussed. It was found that the activity of
carbon monoxide, DME, formaldehyde and methanol oxidation
reaches a maximum at an active component content of 20 – 30 wt. %.
Temperature calcination at 500oC seems to be optimal for the γ–
alumina supported CuO-Cr2O3 catalysts for CO, DME, formaldehyde
and methanol oxidation. A three months industrial experiment was
carried out to elucidate the changes in the catalyst composition
during industrial exploitation of the catalyst and the main reasons for
catalyst deactivation.
It was concluded that the CuO–Cr2O3/γ–alumina supported
catalysts have enhanced activity toward CO, DME, formaldehyde
and methanol oxidation and that these catalysts are suitable for
industrial application. The main reason for catalyst deactivation
seems to be the deposition of iron and molybdenum, coming from the
main reactor, on the active component surface.
Abstract: The pipe inspection operation is the difficult detective
performance. Almost applications are mainly relies on a manual
recognition of defective areas that have carried out detection by an
engineer. Therefore, an automation process task becomes a necessary
in order to avoid the cost incurred in such a manual process. An
automated monitoring method to obtain a complete picture of the
sewer condition is proposed in this work. The focus of the research is
the automated identification and classification of discontinuities in
the internal surface of the pipe. The methodology consists of several
processing stages including image segmentation into the potential
defect regions and geometrical characteristic features. Automatic
recognition and classification of pipe defects are carried out by means
of using an artificial neural network technique (ANN) based on
Radial Basic Function (RBF). Experiments in a realistic environment
have been conducted and results are presented.
Abstract: In this study, a nickel film with nano-crystalline grains,
high hardness and smooth surface was electrodeposited using a post
supercritical carbon dioxide (CO2) mixed Watts electrolyte. Although
the hardness was not as high as its Sc-CO2 counterpart, the thin coating
contained significantly less number of nano-sized pinholes. By
measuring the escape concentration of the dissolved CO2 in post
Sc-CO2 mixed electrolyte with the elapsed time, it was believed that
the residue of dissolved CO2 bubbles should closely relate to the
improvement in hardness and surface roughness over its conventional
plating counterpart. Therefore, shortening the duration of
electroplating with the raise of current density up to 0.5 A/cm2 could
effectively retain more post Sc-CO2 mixing effect. This study not only
confirms the roles of dissolved CO2 bubbles in electrolyte but also
provides a potential process to overcome most issues associated with
the cost in building high-pressure chamber for large size products and
continuous plating using supercritical method.