Abstract: Global warming and continental changes have been
one of the people's issues in the recent years and its consequences
have appeared in the most parts of the earth planet or will appear in
the future. Temperature and Precipitation are two main parameters in
climatology. Any changes in these two parameters in this region
cause widespread changes in the ecosystem and its natural and
humanistic structure. One of the important consequences of this
procedure is change in surface and underground water resources.
Zayanderood watershed basin which is the main central river in Iran
has faced water shortage in the recent years and also it has resulted in
drought in Gavkhuni swamp and the river itself. Managers and
experts in provinces which are the Zayanderood water consumers
believe that global warming; raining decrease and continental
changes are the main reason of water decrease. By statistical
investigation of annual Precipitation and 46 years temperature of
internal and external areas of Zayanderood watershed basin's stations
and by using Kendal-man method, Precipitation and temperature
procedure changes have been analyzed in this basin. According to
obtained results, there was not any noticeable decrease or increase
procedure in Precipitation and annual temperature in the basin during
this period. However, regarding to Precipitation, a noticeable
decrease and increase have been observed in small part of western
and some parts of eastern and southern basin, respectively.
Furthermore, the investigation of annual temperature procedure has
shown that a noticeable increase has been observed in some parts of
western and eastern basin, and also a noticeable increasing procedure
of temperature in the central parts of metropolitan Esfahan can be
observed.
Abstract: This paper proposes a novel stereo vision technique
for top view book scanners which provide us with dense 3d point
clouds of page surfaces. This is a precondition to dewarp bound
volumes independent of 2d information on the page. Our method is
based on algorithms, which normally require the projection of pattern
sequences with structured light. We use image sequences of the
moving stripe lighting of the top view scanner instead of an additional
light projection. Thus the stereo vision setup is simplified without
losing measurement accuracy. Furthermore we improve a surface
model dewarping method through introducing a difference vector
based on real measurements. Although our proposed method is hardly
expensive neither in calculation time nor in hardware requirements
we present good dewarping results even for difficult examples.
Abstract: This paper presents an advance in monitoring and
process control of surface roughness in CNC machine for the turning
and milling processes. An integration of the in-process monitoring
and process control of the surface roughness is proposed and
developed during the machining process by using the cutting force
ratio. The previously developed surface roughness models for turning
and milling processes of the author are adopted to predict the inprocess
surface roughness, which consist of the cutting speed, the
feed rate, the tool nose radius, the depth of cut, the rake angle, and
the cutting force ratio. The cutting force ratios obtained from the
turning and the milling are utilized to estimate the in-process surface
roughness. The dynamometers are installed on the tool turret of CNC
turning machine and the table of 5-axis machining center to monitor
the cutting forces. The in-process control of the surface roughness
has been developed and proposed to control the predicted surface
roughness. It has been proved by the cutting tests that the proposed
integration system of the in-process monitoring and the process
control can be used to check the surface roughness during the cutting
by utilizing the cutting force ratio.
Abstract: The previous study of new metal gasket that contact
width and contact stress an important design parameter for optimizing
metal gasket performance. The optimum design based on an elastic
and plastic contact stress was founded. However, the influence of
flange surface roughness had not been investigated thoroughly. The
flange has many kinds of surface roughness. In this study, we
conducted a gasket model include a flange surface roughness effect. A
finite element method was employed to develop simulation solution. A
uniform quadratic mesh used for meshing the gasket material and a
gradually quadrilateral mesh used for meshing the flange. The gasket
model was simulated by using two simulation stages which is forming
and tightening simulation. A simulation result shows that a smoother
of surface roughness has higher slope for force per unit length. This
mean a squeezed against between flange and gasket will be strong. The
slope of force per unit length for gasket 400-MPa mode was higher
than the gasket 0-MPa mode.
Abstract: In this paper we propose a computational model for the representation and processing of morpho-phonological phenomena in a natural language, like Modern Greek. We aim at a unified treatment of inflection, compounding, and word-internal phonological changes, in a model that is used for both analysis and generation. After discussing certain difficulties cuase by well-known finitestate approaches, such as Koskenniemi-s two-level model [7] when applied to a computational treatment of compounding, we argue that a morphology-based model provides a more adequate account of word-internal phenomena. Contrary to the finite state approaches that cannot handle hierarchical word constituency in a satisfactory way, we propose a unification-based word grammar, as the nucleus of our strategy, which takes into consideration word representations that are based on affixation and [stem stem] or [stem word] compounds. In our formalism, feature-passing operations are formulated with the use of the unification device, and phonological rules modeling the correspondence between lexical and surface forms apply at morpheme boundaries. In the paper, examples from Modern Greek illustrate our approach. Morpheme structures, stress, and morphologically conditioned phoneme changes are analyzed and generated in a principled way.
Abstract: Identifying the nature of protein-nanoparticle
interactions and favored binding sites is an important issue in
functional characterization of biomolecules and their physiological
responses. Herein, interaction of silver nanoparticles with lysozyme
as a model protein has been monitored via fluorescence spectroscopy.
Formation of complex between the biomolecule and silver
nanoparticles (AgNPs) induced a steady state reduction in the
fluorescence intensity of protein at different concentrations of
nanoparticles. Tryptophan fluorescence quenching spectra suggested
that silver nanoparticles act as a foreign quencher, approaching the
protein via this residue. Analysis of the Stern-Volmer plot showed
quenching constant of 3.73 μM−1. Moreover, a single binding site in
lysozyme is suggested to play role during interaction with AgNPs,
having low affinity of binding compared to gold nanoparticles.
Unfolding studies of lysozyme showed that complex of lysozyme-
AgNPs has not undergone structural perturbations compared to the
bare protein. Results of this effort will pave the way for utilization of
sensitive spectroscopic techniques for rational design of
nanobiomaterials in biomedical applications.
Abstract: In this paper, we have proposed two novel plasmonic demultiplexing structures based on metal-insulator-metal surfaces which, beside their compact size, have a very good transmission spectrum. The impact of the key internal parameters on the transmission spectrum is numerically analyzed by using the twodimensional (2D) finite difference time domain (FDTD) method. The proposed structures could be used to develop ultra-compact photonic wavelength demultiplexing devices for large-scale photonic integration.
Abstract: The objective of this paper was to designing a
ventilation system to enhance the performance of roof solar collector
(RSC) for reducing heat accumulation inside the house. The RSC has
1.8 m2 surface area made of CPAC monier roof tiles on the upper part
and gypsum board on the lower part. The space between CPAC
monier and gypsum board was fixed at 14 cm.
Ventilation system of modified roof solar collector (modified
RSC) consists of 9 tubes of 0.15m diameter and installed in the
lower part of RSC. Experimental result showed that the temperature
of the room, and attic temperature. The average temperature
reduction of room of house used modified RSC is about 2oC. and the
percentage of room temperature reduction varied between 0 to 10%.
Therefore, modified RSC is an interesting option in the sense that it
promotes solar energy and conserve energy.
Abstract: Enzymatic saccharification of biomass for reducing
sugar production is one of the crucial processes in biofuel production
through biochemical conversion. In this study, enzymatic
saccharification of dilute potassium hydroxide (KOH) pre-treated
Tetraselmis suecica biomass was carried out by using cellulase
enzyme obtained from Trichoderma longibrachiatum. Initially, the
pre-treatment conditions were optimised by changing alkali reagent
concentration, retention time for reaction, and temperature. The T.
suecica biomass after pre-treatment was also characterized using
Fourier Transform Infrared Spectra and Scanning Electron
Microscope. These analyses revealed that the functional group such
as acetyl and hydroxyl groups, structure and surface of T. suecica
biomass were changed through pre-treatment, which is favourable for
enzymatic saccharification process. Comparison of enzymatic
saccharification of untreated and pre-treated microalgal biomass
indicated that higher level of reducing sugar can be obtained from
pre-treated T. suecica. Enzymatic saccharification of pre-treated T.
suecica biomass was optimised by changing temperature, pH, and
enzyme concentration to solid ratio ([E]/[S]). Highest conversion of
carbohydrate into reducing sugar of 95% amounted to reducing sugar
yield of 20 (wt%) from pre-treated T. suecica was obtained from
saccharification, at temperature: 40°C, pH: 4.5 and [E]/[S] of 0.1
after 72 h of incubation. Hydrolysate obtained from enzymatic
saccharification of pretreated T. suecica biomass was further
fermented into biobutanol using Clostridium saccharoperbutyliticum
as biocatalyst. The results from this study demonstrate a positive
prospect of application of dilute alkaline pre-treatment to enhance
enzymatic saccharification and biobutanol production from
microalgal biomass.
Abstract: The objective of this research was to study factors,
which were affected on surface roughness in high speed milling of
hardened tool steel. Material used in the experiment was tool steel JIS
SKD 61 that hardened on 60 ±2 HRC. Full factorial experimental
design was conducted on 3 factors and 3 levels (3
3
designs) with 2
replications. Factors were consisted of cutting speed, feed rate, and
depth of cut. The results showed that influenced factor affected to
surface roughness was cutting speed, feed rate and depth of cut which
showed statistical significant. Higher cutting speed would cause on
better surface quality. On the other hand, higher feed rate would cause
on poorer surface quality. Interaction of factor was found that cutting
speed and depth of cut were significantly to surface quality. The
interaction of high cutting speed associated with low depth of cut
affected to better surface quality than low cutting speed and high depth
of cut.
Abstract: This paper considers the effect of heat generation
proportional l to (T - T∞ )p , where T is the local temperature and T∞
is the ambient temperature, in unsteady free convection flow near the
stagnation point region of a three-dimensional body. The fluid is
considered in an ambient fluid under the assumption of a step change
in the surface temperature of the body. The non-linear coupled partial
differential equations governing the free convection flow are solved
numerically using an implicit finite-difference method for different
values of the governing parameters entering these equations. The
results for the flow and heat characteristics when p ≤ 2 show that
the transition from the initial unsteady-state flow to the final steadystate
flow takes place smoothly. The behavior of the flow is seen
strongly depend on the exponent p.
Abstract: Inorganic nanoparticles filled polymer composites
have extended their multiple functionalities to various applications,
including mechanical reinforcement, gas barrier, dimensional
stability, heat distortion temperature, flame-retardant, and thermal
conductivity. Sodium stearate-modified calcium carbonate (CaCO3)
nanoparticles were prepared using surface modification method. The
results showed that sodium stearate attached to the surface of CaCO3
nanoparticles with the chemical bond. The effect of modified CaCO3
nanoparticles on thermal properties of polypropylene (PP) was
studied by means of differential scanning calorimetry (DSC) and
Thermogravimetric analysis (TGA). It was found that CaCO3
significantly affected the crystallization temperature and
crystallization degree of PP. Effect of the modified CaCO3 content on
mechanical properties of PP/CaCO3 nanocomposites was also
studied. The results showed that the modified CaCO3 can effectively
improve the mechanical properties of PP. In comparison with PP, the
impact strength of PP/CaCO3 nanocomposites increased by about
65% and the hardness increased by about 5%.
Abstract: Intermetallic Ni3Al – based alloys belong to a group
of advanced materials characterized by good chemical and physical
properties (such as structural stability, corrosion resistance) which
offer advenced technological applications. The paper presents the
study of catalytic properties of Ni3Al foils (thickness approximately
50 &m) in the methanol and hexane decomposition. The egzamined
material posses microcrystalline structure without any additional
catalysts on the surface. The better catalytic activity of Ni3Al foils
with respect to quartz plates in both methanol and hexane
decomposition was confirmed. On thin Ni3Al foils the methanol
conversion reaches approximately 100% above 480 oC while the
hexane conversion reaches approximately 100% (98,5%) at 500 oC.
Deposit formed during the methanol decomposition is built up of
carbon nanofibers decorated with metal-like nanoparticles.
Abstract: Participation in sporting activities can lead to injury.
Sport injuries have been widely studied in many sports including the
more extreme categories of aquatic board sports. Kitesurfing is a
relatively new water surface action sport, and has not yet been
widely studied in terms of injuries and stress on the body. The aim of
this study was to get information about which injuries that are most
common among kitesurfing participants, where they occur, and their
causes. Injuries were studied using an international open web
questionnaire (n=206).
The results showed that many respondents reported injuries, in
total 251 injuries to knee (24%), ankle (17%), trunk (16%) and
shoulders (10%), often sustained while doing jumps and tricks
(40%). Among the reported injuries were joint injuries (n=101),
muscle/tendon damages (n=47), wounds and cuts (n=36) and bone
fractures (n=28). Also environmental factors and equipment can
influence the risk of injury, or the extent of injury in a hazardous
situation. Conclusively, the information from this retrospective study
supports earlier studies in terms of prevalence and site of injuries.
Suggestively, this information should be used for to build a
foundation of knowledge about the sport for development of
applications for physical training and product development.
Abstract: Analysis for the propagation of elastic waves in
arbitrary anisotropic plates is investigated, commencing with a
formal analysis of waves in a layered plate of an arbitrary anisotropic
media, the dispersion relations of elastic waves are obtained by
invoking continuity at the interface and boundary of conditions on
the surfaces of layered plate. The obtained solutions can be used for
material systems of higher symmetry such as monoclinic,
orthotropic, transversely isotropic, cubic, and isotropic as it is
contained implicitly in the analysis. The cases of free layered plate
and layered half space are considered separately. Some special cases
have also been deduced and discussed. Finally numerical solution of
the frequency equations for an aluminum epoxy is carried out, and
the dispersion curves for the few lower modes are presented. The
results obtained theoretically have been verified numerically and
illustrated graphically.
Abstract: We have devised a thermal carpet cloak theoretically
and implemented in silicon using layered metamaterial. The layered
metamaterial is composed of single crystalline silicon and its phononic
crystal. The design is based on a coordinate transformation. We
demonstrate the result with numerical simulation. Great cloaking
performance is achieved as a thermal insulator is well hidden under the
thermal carpet cloak. We also show that the thermal carpet cloak can
even the temperature on irregular surface. Using thermal carpet cloak
to manipulate the heat conduction is effective because of its low
complexity.
Abstract: This paper describes a computer-aided design for
design of the concave globoidal cam with cylindrical rollers and
swinging follower. Four models with different modeling methods are
made from the same input data. The input data are angular input and
output displacements of the cam and the follower and some other
geometrical parameters of the globoidal cam mechanism. The best
cam model is the cam which has no interference with the rollers
when their motions are simulated in assembly conditions. The
angular output displacement of the follower for the best cam is also
compared with that of in the input data to check errors. In this study,
Pro/ENGINEER® Wildfire 2.0 is used for modeling the cam,
simulating motions and checking interference and errors of the
system.
Abstract: We propose the use of magneto-optic Kerr effect (MOKE) to realize single-qubit quantum gates. We consider longitudinal and polar MOKE in reflection geometry in which the magnetic field is parallel to both the plane of incidence and surface of the film. MOKE couples incident TE and TM polarized photons and the Hamiltonian that represents this interaction is isomorphic to that of a canonical two-level quantum system. By varying the phase and amplitude of the magnetic field, we can realize Hadamard, NOT, and arbitrary phase-shift single-qubit quantum gates. The principal advantage is operation with magnetically non-transparent materials.
Abstract: The chemical degradation of dieldrin in ferric
sulfide and iron powder aqueous suspension was investigated
in laboratory batch type experiments. To identify the reaction
mechanism, reduced copper was used as reductant. More than
90% of dieldrin was degraded using both reaction systems after
29 days. Initial degradation rate of the pesticide using ferric
sulfide was superior to that using iron powder. The reaction
schemes were completely dissimilar even though the ferric ion
plays an important role in both reaction systems. In the case of
metallic iron powder, dieldrin undergoes partial dechlorination.
This reaction proceeded by reductive hydrodechlorination with
the generation of H+, which arise by oxidation of ferric iron.
This reductive reaction was accelerated by reductant but
mono-dechlorination intermediates were accumulated. On the
other hand, oxidative degradation was observed in the reaction
with ferric sulfide, and the stable chemical structure of dieldrin
was decomposed into water-soluble intermediates. These
reaction intermediates have no chemical structure of drin class.
This dehalogenation reaction assumes to occur via the adsorbed
hydroxyl radial generated on the surface of ferric sulfide.
Abstract: This paper deals optimized model to investigate the
effects of peak current, pulse on time and pulse off time in EDM performance on material removal rate of titanium alloy utilizing copper tungsten as electrode and positive polarity of the electrode. The experiments are carried out on Ti6Al4V. Experiments were
conducted by varying the peak current, pulse on time and pulse off time. A mathematical model is developed to correlate the influences of these variables and material removal rate of workpiece. Design of
experiments (DOE) method and response surface methodology
(RSM) techniques are implemented. The validity test of the fit and adequacy of the proposed models has been carried out through
analysis of variance (ANOVA). The obtained results evidence that as
the material removal rate increases as peak current and pulse on time
increases. The effect of pulse off time on MRR changes with peak ampere. The optimum machining conditions in favor of material removal rate are verified and compared. The optimum machining
conditions in favor of material removal rate are estimated and verified with proposed optimized results. It is observed that the developed model is within the limits of the agreeable error (about
4%) when compared to experimental results. This result leads to desirable material removal rate and economical industrial machining to optimize the input parameters.