Abstract: The recycling of concrete, bricks and masonry rubble
as concrete aggregates is an important way to contribute to a
sustainable material flow. However, there are still various
uncertainties limiting the widespread use of Recycled Concrete
Aggregates (RCA). The fluctuations in the composition of grade
recycled aggregates and their influence on the properties of fresh and
hardened concrete are of particular concern regarding the use of
RCA. Most of problems occurring while using recycled concrete
aggregates as aggregates are due to higher porosity and hence higher
water absorption, lower mechanical strengths, residual impurities on
the surface of the RCA forming weaker bond between cement paste
and aggregate. So, the reuse of RCA is still limited. Efficient
polymer based treatment is proposed in order to reuse RCA easier.
The silicon-based polymer treatments of RCA were carried out and
were compared. This kind of treatment can improve the properties of
RCA such as the rate of water absorption on treated RCA is
significantly reduced.
Abstract: Electrical Discharge Machine (EDM) is especially
used for the manufacturing of 3-D complex geometry and hard
material parts that are extremely difficult-to-machine by conventional
machining processes. In this paper authors review the research work
carried out in the development of die-sinking EDM within the past
decades for the improvement of machining characteristics such as
Material Removal Rate, Surface Roughness and Tool Wear Ratio. In
this review various techniques reported by EDM researchers for
improving the machining characteristics have been categorized as
process parameters optimization, multi spark technique, powder
mixed EDM, servo control system and pulse discriminating. At the
end, flexible machine controller is suggested for Die Sinking EDM to
enhance the machining characteristics and to achieve high-level
automation. Thus, die sinking EDM can be integrated with Computer
Integrated Manufacturing environment as a need of agile
manufacturing systems.
Abstract: The incidence of mechanical fracture of an
automobile piston rings prompted development of fracture analysis
method on this case. The three rings (two compression rings and one
oil ring) were smashed into several parts during the power-test (after
manufacturing the engine) causing piston and liner to be damaged.
The radial and oblique cracking happened on the failed piston rings.
The aim of the fracture mechanics simulations presented in this paper
was the calculation of particular effective fracture mechanics
parameters, such as J-integrals and stress intensity factors. Crack
propagation angles were calculated as well. Two-dimensional
fracture analysis of the first compression ring has been developed in
this paper using ABAQUS CAE6.5-1 software. Moreover, SEM
fractography was developed on fracture surfaces and is discussed in
this paper. Results of numerical calculations constitute the basis for
further research on real object.
Abstract: Eutrophication of surface water is one of the most
widespread environmental problems at present. Large number of
pilgrims and tourists visit sacred artificial tank known as “Brahma
Sarover” located at Kurukshetra, India to take holy dip and perform
religious ceremonies. The sources of pollutants include impurities in
feed water, mass bathing, religious offerings and windblown
particulate matter. Studies so far have focused mainly on assessing
water quality for bathing purpose by using physico-chemical and
bacteriological parameters. No effort has been made to assess nutrient
concentration and trophic status of the tank to take more appropriate
measures for improving water quality on long term basis. In the
present study, total nitrogen, total phosphorous and chlorophyll a
measurements have been done to assess the nutrient level and trophic
status of the tank. The results show presence of high concentration of
nutrients and Chlorophyll a indicating mesotrophic and eutrophic
state of the tank. Phosphorous has been observed as limiting nutrient
in the tank water.
Abstract: Biodiesel production with used frying by
transesterification reaction with methanol, using a commercial
kaolinite thermally-activated solid acid catalyst was investigated.
The surface area, the average pore diameter and pore volume of the
kaolinite catalyst were 10 m2/g, 13.0 nm and 30 mm3/g, respectively.
The optimal conditions for the transesterification reaction were
determined to be oil/methanol, in a molar ratio 1:31, temperature 160
ºC and catalyst concentration of 3% (w/w). The yield of fatty acids
methyl esters (FAME) was 92.4% after 2 h of reaction. This method
of preparation of biodiesel can be a positive alternative for utilizing
used frying corn oil for feedstock of biodiesel combined with the
inexpensive catalyst.
Abstract: This paper describes a method to measure and
compensate a 4 axes ultra-precision machine tool that generates micro
patterns on the large surfaces. The grooving machine is usually used
for making a micro mold for many electrical parts such as a light guide
plate for LCD and fuel cells. The ultra precision machine tool has three
linear axes and one rotational table. Shaping is usually used to
generate micro patterns. In the case of 50 μm pitch and 25 μm height
pyramid pattern machining with a 90° wedge angle bite, one of linear
axis is used for long stroke motion for high cutting speed and other
linear axis are used for feeding. The triangular patterns can be
generated with many times of long stroke of one axis. Then 90°
rotation of work piece is needed to make pyramid patterns with
superposition of machined two triangular patterns.
To make a two dimensional positioning error, straightness of two
axes in out of plane, squareness between the each axis are important.
Positioning errors, straightness and squarness were measured by laser
interferometer system. Those were compensated and confirmed by
ISO230-6. One of difficult problem to measure the error motions is
squareness or parallelism of axis between the rotational table and
linear axis. It was investigated by simultaneous moving of rotary table
and XY axes. This compensation method is introduced in this paper.
Abstract: The aim of this research is to evaluate surface
roughness and develop a multiple regression model for surface roughness as a function of cutting parameters during the turning of
flame hardened medium carbon steel with TiN-Al2O3-TiCN coated inserts. An experimental plan of work and signal-to-noise ratio (S/N)
were used to relate the influence of turning parameters to the
workpiece surface finish utilizing Taguchi methodology. The effects
of turning parameters were studied by using the analysis of variance (ANOVA) method. Evaluated parameters were feed, cutting speed,
and depth of cut. It was found that the most significant interaction among the considered turning parameters was between depth of cut and feed. The average surface roughness (Ra) resulted by TiN-Al2O3-
TiCN coated inserts was about 2.44 μm and minimum value was 0.74 μm. In addition, the regression model was able to predict values for surface roughness in comparison with experimental values within
reasonable limit.
Abstract: The amplitude response of infrared (IR) sensors
depends on the reflectance properties of the target. Therefore, in
order to use IR sensor for measuring distances accurately, prior
knowledge of the surface must be known. This paper describes the
Phong Illumination Model for determining the properties of a surface
and subsequently calculating the distance to the surface. The angular
position of the IR sensor is computed as normal to the surface for
simplifying the calculation. Ultrasonic (US) sensor can provide the
initial information on distance to obtain the parameters for this
method. In addition, the experimental results obtained by using
LabView are discussed. More care should be taken when placing the
objects from the sensors during acquiring data since the small change
in angle could show very different distance than the actual one.
Since stereo camera vision systems do not perform well under some
environmental conditions such as plain wall, glass surfaces, or poor
lighting conditions, the IR and US sensors can be used additionally to
improve the overall vision systems of mobile robots.
Abstract: In this paper, we are presenting a new type of pointing interface for computers which provides mouse functionalities with near surface haptic feedback. Further, it can be configured as a haptic display where users may feel the basic geometrical shapes in the GUI by moving the finger on top of the device surface. These functionalities are achieved by tracking three dimensional positions of the neodymium magnet using Hall Effect sensors grid and generating like polarity haptic feedback using an electromagnet array. This interface brings the haptic sensations to the 3D space where previously it is felt only on top of the buttons of the haptic mouse implementations.
Abstract: Repairing of the cracks by fiber metal laminates
(FMLs) was first done by some aeronautical laboratories in early
1970s. In this study, experimental investigations were done on the
effect of repairing the center-cracked aluminum plates using the FML
patches. The repairing processes were conducted to characterize the
response of the repaired structures to tensile tests. The composite
patches were made of one aluminum layer and two woven glassepoxy
composite layers. Three different crack lengths in three crack
angles and different patch lay-ups were examined. It was observed
for the lengthen cracks, the effect of increasing the crack angle on
ultimate tensile load in the structure was increase. It was indicated
that the situation of metal layer in the FML patches had an important
effect on the tensile response of the tested specimens. It was found
when the aluminum layer is farther, the ultimate tensile load has the
highest amount.
Abstract: The theoretical prediction of the acoustical
polarization effects in the heterogeneous composites, made of thick
elastic solids with thin nematic films, is presented. The numericalanalytical
solution to the problem of the different wave propagation
exhibits some new physical effects in the low frequency domain: the
appearance of the critical frequency and the existence of the narrow
transition zone where the wave rapidly changes its speed. The
associated wave attenuation is highly perturbed in this zone. We also
show the possible appearance of the critical frequencies where the
attenuation changes the sign. The numerical results of parametrical
analysis are presented and discussed.
Abstract: This paper present some preliminary work on the
preparation and physicochemical caracterization of nanocomposite
MFI-alumina structures based on alumina hollow fibres. The fibers
are manufactured by a wet spinning process. α-alumina particles were
dispersed in a solution of polysulfone in NMP. The resulting slurry is
pressed through the annular gap of a spinneret into a precipitation
bath. The resulting green fibres are sintered. The mechanical strength
of the alumina hollow fibres is determined by a three-point-bending
test while the pore size is characterized by bubble-point testing. The
bending strength is in the range of 110 MPa while the average pore
size is 450 nm for an internal diameter of 1 mm and external diameter
of 1.7 mm. To characterize the MFI membranes various techniques
were used for physicochemical characterization of MFI–ceramic
hollow fibres membranes: The nitrogen adsorption, X-ray
diffractometry, scanning electron microscopy combined with X
emission microanalysis. Scanning Electron Microscopy (SEM) and
Energy Dispersive Microanalysis by the X-ray were used to observe
the morphology of the hollow fibre membranes (thickness,
infiltration into the carrier, defects, homogeneity). No surface film,
has been obtained, as observed by SEM and EDX analysis and
confirmed by high temperature variation of N2 and CO2 gas
permeances before cation exchange. Local analysis and characterise
(SEM and EDX) and overall (by ICP elemental analysis) were
conducted on two samples exchanged to determine the quantity and
distribution of the cation of cesium on the cross section fibre of the
zeolite between the cavities.
Abstract: Microstrip antennas are conformable to planar and
nonplanar surfaces, simple and inexpensive to fabricate using modern
printed-circuit technology. Circular polarization of low-profile
microstrip patch with high bandwidth is achieved in this research
through the use of a three-cross-arms branch-line coupler with
sequential rotated arrays, another low-profile antenna of hollow
cylinder is also proposed and the function of reconnaissance with
microstrip antenna on Mini UAV (unmanned aerial vehicle) are
evaluated in practical flight test.
Abstract: This paper presents the experimental results of
comparison between leakage currents and discharge currents. The leakage currents were obtained on polluted porcelain insulator.
Whereas, the discharge currents were obtained on lightly artificial
polluted porcelain specimen. The conducted measurements were
leakage current or discharge current and applied voltage. The insulator or specimen was in a hermetically sealed chamber, and the
current waveforms were analyzed using FFT.
The result indicated that the leakage current (LC) on low RH condition the fifth harmonic would be visible, and followed by the
seventh harmonic. The insulator had capacitive property. Otherwise,
on 99% relative humidity, the fifth harmonic would also be visible,
and the phase angle reached up to 12.2 degree. Whereas, on discharge current, the third harmonic would be visible, and followed
by fifth harmonic. The third harmonic would increase as pressure reduced. On this condition, the specimen had a non-linear characteristics
Abstract: This paper presents the experimental results of silicone rubber housing material for 24kV lightning arrester under artificial accelerated ageing test based on IEC 61109 specifications. Specimens having inclined and alternated shed made of HTV silicone rubber with ATH content and having leakage distance 625 mm were tested continuously 1000 hrs in artificial salt fog chamber. After 1000 hrs of salt fog ageing test, obviously surface erosion was observed on trunk between the upper large shed and the lower small shed near the energized end. Decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Chemical analysis by ATR-FTIR confirmed the observation results.
Abstract: This study describes the preparation of a novel proton
conducting membranes based on bacterial cellulose (BC) modified by
grafting of 2-acrylamido-2-methyl-1 -propanesulfonic acid (AMPS)
through UV-induced graft polymerization. These AMPS-g-BC
membranes have been characterized by various techniques including
FTIR, SEM and TGA, to find their successful grafting of AMPS on
BC, surface morphology and thermal stability, respectively. Physical
properties of AMPS-g-BC membranes have been assessed in terms of
Lamda value( λ ), ion exchange capacity(IEC) and proton
conductivity. The relationship between degree of grafting and AMPS
concentration used for grafting has been determined by weight gain
method. An optimum proton conductivity equal to 2.89x10-2 S cm-1
and IEC value equal to 1.79 mmol g-1 have been obtained when 20
wt% AMPS concentration is used for grafting (i.e. the corresponding
membrane is notated as AMPS20-g-BC).
Abstract: ZnO-SnO2 i.e. Zinc-Tin-Oxide (ZTO) thin films were
deposited on glass substrate with varying concentrations (ZnO:SnO2
- 100:0, 90:10, 70:30 and 50:50 wt.%) at room temperature by flash
evaporation technique. These deposited ZTO film were annealed at
450 0C in vacuum. These films were characterized to study the effect
of annealing on the structural, electrical, and optical properties.
Atomic force microscopy (AFM) and Scanning electron microscopy
(SEM) images manifest the surface morphology of these ZTO thin
films. The apparent growth of surface features revealed the formation
of nanostructure ZTO thin films. The small value of surface
roughness (root mean square RRMS) ensures the usefulness in
optical coatings. The sheet resistance was also found to be decreased
for both types of films with increasing concentration of SnO2. The
optical transmittance found to be decreased however blue shift has
been observed after annealing.
Abstract: Two different superhydrophobic surfaces were
elaborated and their oil repellency behavior was evaluated using
several liquid with different surface tension. A silicone rubber/SiO2
nanocomposite coated (A) on aluminum substrate by “spin-coating"
and the sample B was an anodized aluminum surface covered by
Teflon-like coating. A high static contact angle about ∼162° was
measured for two prepared surfaces on which the water droplet rolloff.
Scanning electron microscopy (SEM) showed the presence of
micro/nanostructures for both sample A and B similar to that of lotus
leaf.
However the sample A presented significantly different behaviour
of wettability against the low surface tension liquid. Sample A has
been wetted totally by oil (dodecan) droplet while sample B showed
oleophobic behaviour. Oleophobic property of Teflon like coating
can be contributed to the presence of CF2 and CF3 functional group
which was shown by XPS analysis.
Abstract: The study investigates the mixing performance of
electrokinetically-driven power-law fluids in a microchannel
containing patterned trapezoid blocks. The effects of the geometry
parameters of the patterned trapezoid blocks and the flow behavior
index in the power-law model on the mixing efficiency within the
microchannel are explored. The results show that the mixing efficiency
can be improved by increasing the width of the blocks and extending
the length of upper surface of the blocks. In addition, the results show
that the mixing efficiency increases with an increasing flow behavior
index. Furthermore, it is shown that a heterogeneous patterning of the
zeta potential on the upper surfaces of the trapezoid blocks prompts
the formation of local flow recirculations, and therefore improves the
mixing efficiency. Consequently, it is shown that the mixing
performance improves with an increasing magnitude of the
heterogeneous surface zeta potential.
Abstract: Wetting characteristics of reactive (Sn–0.7Cu solder)
and non– reactive (castor oil) wetting of liquids on Cu and Ag plated
Al substrates have been investigated. Solder spreading exhibited
capillary, gravity and viscous regimes. Oils did not exhibit noticeable
spreading regimes. Solder alloy showed better wettability on Ag
coated Al substrate compared to Cu plating. In the case of castor oil,
Cu coated Al substrate exhibited good wettability as compared to Ag
coated Al substrates. The difference in wettability during reactive
wetting of solder and non–reactive wetting of oils is attributed to the
change in the surface energies of Al substrates brought about by the
formation of intermetallic compounds (IMCs).