Abstract: Ultra-wide band (UWB) communication is one of
the most promising technologies for high data rate wireless networks
for short range applications. This paper proposes a blind channel
estimation method namely IMM (Interactive Multiple Model) Based
Kalman algorithm for UWB OFDM systems. IMM based Kalman
filter is proposed to estimate frequency selective time varying
channel. In the proposed method, two Kalman filters are concurrently
estimate the channel parameters. The first Kalman filter namely
Static Model Filter (SMF) gives accurate result when the user is static
while the second Kalman filter namely the Dynamic Model Filter
(DMF) gives accurate result when the receiver is in moving state. The
static transition matrix in SMF is assumed as an Identity matrix
where as in DMF, it is computed using Yule-Walker equations. The
resultant filter estimate is computed as a weighted sum of individual
filter estimates. The proposed method is compared with other existing
channel estimation methods.
Abstract: The response of King Abdulla Canal (KAC) water to the upgrade of As Samra Wastewater Treatment Plant which discharges its effluent to the Zarqa River is investigated. Time series quality data that extends between October 2005 and December 2009 obtained by a state of the art telemetric monitoring system were analyzed for COD, EC, TP and TN at two monitoring stations located upstream and downstream of the confluence of the Zarqa River with KAC. The samples- means and the t-test showed that there has been significant improvement in the quality of the KAC water for COD, and TP. However, the improvement in the TN was found statistically insignificant, whereas the EC of the KAC was unaffected by the upgrade. Comparing the selected parameters with the standards and guidelines for using treated wastewater in irrigation showed that the KAC water has improved towards meeting the required standards and guidelines for treated wastewater reuse in irrigation.
Abstract: In the Northern hemisphere, sheep reproduction is
seasonal (September-November). Among several natural factors
influencing the reproduction status of rams, we studied the daylight
length and temperature. Rams from different breeds were studied:
Merinos de Palas (half-precocious), Karakul de Botosani (halfbelated)
and Turcana (belated breed, low reproductive plasticity). In
Merinos de Palas, ejaculate volume during sexual repose is 51.3%
from normal quantity. When autumn climate was experimentally
induced, ejaculate volume reached 98.45% (Merinos), 94.97%
(Karakul) and 97.59% (Turcana). Semen density increased from
1.031-1.033 till 1.035 after exposition to artificial light and
temperature conditions. Spermatozoids mobility and sperm pH
improved, passing over 82% and 6.75, values identical to those in the
natural reproduction season. Behaviour analysis after
photoperiodicity indicated that over 83.3% Merinos and Karakul
males and all Turcana rams exteriorised normal and intense sexual
reflexes. Certain effort and reduced expenses brought rams in good
condition, producing higher quantity and quality sperm.
Abstract: In the present paper the results of a numerical study are presented, numerical models were developed to simulate the behaviour of vertical massive dikes. The proposed models were developed according to the geometry, boundary conditions, loading conditions and initial conditions of a physical model taken as reference. The results obtained were compared to the experimental data. As far as the overall behaviour, the displacements and the failure mechanisms of the dikes is concerned, the numerical results were in good agreement with the experimental results, which clearly indicates a good quality of numerical modelling. The validated numerical models were used in a parametric study were the displacements and failure mechanisms were fully investigated. Out of the results obtained, some conclusions and recommendations related to the design of massive dikes are proposed.
Abstract: Hydrodynamic pressures acting on upstream of concrete dams during an earthquake are an important factor in designing and assessing the safety of these structures in Earthquake regions. Due to inherent complexities, assessing exact hydrodynamic pressure is only feasible for problems with simple geometry. In this research, the governing equation of concrete gravity dam reservoirs with effect of fluid viscosity in frequency domain is solved and then compared with that in which viscosity is assumed zero. The results show that viscosity influences the reservoir-s natural frequency. In excitation frequencies near the reservoir's natural frequencies, hydrodynamic pressure has a considerable difference in compare to the results of non-viscose fluid.
Abstract: Adopting Zakowski-s upper approximation operator
C and lower approximation operator C, this paper investigates
granularity-wise separations in covering approximation spaces. Some
characterizations of granularity-wise separations are obtained by
means of Pawlak rough sets and some relations among granularitywise
separations are established, which makes it possible to research
covering approximation spaces by logical methods and mathematical
methods in computer science. Results of this paper give further
applications of Pawlak rough set theory in pattern recognition and
artificial intelligence.
Abstract: Mobile robots are used in a large field of scenarios,
like exploring contaminated areas, repairing oil rigs under water,
finding survivors in collapsed buildings, etc. Currently, there is no
unified intuitive user interface (UI) to control such complex mobile
robots. As a consequence, some scenarios are done without the
exploitation of experience and intuition of human teleoperators.
A novel framework has been developed to embed a flexible and
modular UI into a complete 3-D virtual reality simulation system.
This new approach wants to access maximum benefits of human
operators. Sensor information received from the robot is prepared for
an intuitive visualization. Virtual reality metaphors support the
operator in his decisions. These metaphors are integrated into a real
time stereo video stream. This approach is not restricted to any
specific type of mobile robot and allows for the operation of different
robot types with a consistent concept and user interface.
Abstract: The present project was conducted with the
circumferential-fuel-jets inverse diffusion flame (CIDF) burner
burning liquefied petroleum gas (LPG) enriched with 50% of
hydrogen fuel (H2). The range of stable operation of the CIDF burner
in terms of Reynolds number (from laminar to turbulent flow regions),
equivalence ratio and fuel jet velocity of LPG of the 50% H2-LPG
mixed fuel was identified. Experiments were also carried out to
investigate the flame structures of the LPG flame and LPG enriched H2
flame. Experimental results obtained from these two flames were
compared to fully explore the influence of hydrogen addition on flame
stability. Flame heights obtained by burning these two kinds of fuels at
various equivalence ratios were compared and correlated with the
Global Momentum Ratio (GMR).
Abstract: The evaluation of the question answering system is a major research area that needs much attention. Before the rise of domain-oriented question answering systems based on natural language understanding and reasoning, evaluation is never a problem as information retrieval-based metrics are readily available for use. However, when question answering systems began to be more domains specific, evaluation becomes a real issue. This is especially true when understanding and reasoning is required to cater for a wider variety of questions and at the same time achieve higher quality responses The research in this paper discusses the inappropriateness of the existing measure for response quality evaluation and in a later part, the call for new standard measures and the related considerations are brought forward. As a short-term solution for evaluating response quality of heterogeneous systems, and to demonstrate the challenges in evaluating systems of different nature, this research presents a black-box approach using observation, classification scheme and a scoring mechanism to assess and rank three example systems (i.e. AnswerBus, START and NaLURI).
Abstract: Swedish truck industry is investigating the possibility
for implementing the use of Compacted Graphite Iron (CGI) in their
heavy duty diesel engines. Compared to the alloyed gray iron used
today, CGI has superior mechanical properties but not as good
machinability. Another issue that needs to be addressed when
implementing CGI is the inhomogeneous microstructure when the
cast component has different section thicknesses, as in cylinder
blocks. Thinner sections results in finer pearlite, in the material, with
higher strength. Therefore an investigation on its influence on
machinability was needed. This paper focuses on the effect that
interlamellar distance in pearlite has on CGI machinability and
material physical properties. The effect of pearlite content and
nodularity is also examined. The results showed that interlamellar
distance in pearlite did not have as large effect on the material
physical properties or machinability as pearlite content. The paper
also shows the difficulties of obtaining a homogeneous
microstructure in inhomogeneous workpieces.
Abstract: Investigations of the unimolecular decomposition of
vinyl ethyl ether (VEE), vinyl propyl ether (VPE) and vinyl butyl
ether (VBE) have shown that activation of the molecule of a ether
results in formation of a cyclic construction - the transition state (TS),
which may lead to the displacement of the thermodynamic
equilibrium towards the reaction products. The TS is obtained by
applying energy minimization relative to the ground state of an ether
under the program MM2 when taking into account the hydrogen bond
formation between a hydrogen atom of alkyl residue and the extreme
atom of carbon of the vinyl group. The dissociation of TS up to the
products is studied by energy minimization procedure using the
mathematical program Gaussian. The obtained calculation data for
VEE testify that the decomposition of this ether may be conditioned
by hydrogen bond formation for two possible versions: when α- or β-
hydrogen atoms of the ethyl group are bound to carbon atom of the
vinyl group. Applying the same calculation methods to other ethers
(VPE and VBE) it is shown that only in the case of hydrogen bonding
between α-hydrogen atom of the alkyl residue and the extreme atom
of carbon of the vinyl group (αH---C) results in decay of theses
ethers.
Abstract: This paper proposes a novel spectrum sensing technique
for the digital video broadcasting-terrestrial (DVB-T) systems, which
utilizes the periodicity of pilot signals in the orthogonal frequency
division multiplexing (OFDM) symbols. The proposed scheme can
overcome the effect of the timing synchronization error by recorrelating
the correlation values in the same sample distances. The
numerical results demonstrate that the detection probability performance
of the proposed scheme outperforms that of the conventional
scheme when there exists a timing synchronization error.
Abstract: Indium-tin oxide films are deposited by low plasma
temperature RF sputtering on highly flexible modification of glycol
polyethyleneterephtalate substrates. The produced layers are
characterized with transparency over 82 % and sheet resistance of
86.9 Ω/square. The film’s conductivity was further improved by
additional UV illumination from light source (365 nm), having power
of 250 W. The influence of the UV exposure dose on the structural
and electro-optical properties of ITO was investigated. It was
established that the optimum time of illumination is 10 minutes and
further UV treatment leads to polymer substrates degradation.
Structural and bonds type analysis show that at longer treatment
carbon atoms release and diffuse into ITO films, which worsen their
electrical behavior. For the optimum UV dose the minimum sheet
resistance was measured to be 19.2 Ω/square, and the maximum
transparency remained almost unchanged – above 82 %.
Abstract: The storage of thermal energy as a latent heat of phase
change material (PCM) has created considerable interest among
researchers in recent times. Here, an attempt is made to carry out
numerical investigations to analyze the performance of latent heat
storage units (LHSU) employing phase change material. The
mathematical model developed is based on an enthalpy formulation.
Freezing time of PCM packed in three different shaped containers
viz. rectangular, cylindrical and cylindrical shell is compared. The
model is validated with the results available in the literature. Results
show that for the same mass of PCM and surface area of heat
transfer, cylindrical shell container takes the least time for freezing
the PCM and this geometric effect is more pronounced with an
increase in the thickness of the shell than that of length of the shell.
Abstract: The fundamental aim of extended expansion concept is
to achieve higher work done which in turn leads to higher thermal
efficiency. This concept is compatible with the application of
turbocharger and LHR engine. The Low Heat Rejection engine was
developed by coating the piston crown, cylinder head inside with
valves and cylinder liner with partially stabilized zirconia coating of
0.5 mm thickness. Extended expansion in diesel engines is termed as
Miller cycle in which the expansion ratio is increased by reducing the
compression ratio by modifying the inlet cam for late inlet valve
closing. The specific fuel consumption reduces to an appreciable level
and the thermal efficiency of the extended expansion turbocharged
LHR engine is improved.
In this work, a thermodynamic model was formulated and
developed to simulate the LHR based extended expansion
turbocharged direct injection diesel engine. It includes a gas flow
model, a heat transfer model, and a two zone combustion model. Gas
exchange model is modified by incorporating the Miller cycle, by
delaying inlet valve closing timing which had resulted in considerable
improvement in thermal efficiency of turbocharged LHR engines. The
heat transfer model, calculates the convective and radiative heat
transfer between the gas and wall by taking into account of the
combustion chamber surface temperature swings. Using the two-zone
combustion model, the combustion parameters and the chemical
equilibrium compositions were determined. The chemical equilibrium
compositions were used to calculate the Nitric oxide formation rate by
assuming a modified Zeldovich mechanism. The accuracy of this
model is scrutinized against actual test results from the engine. The
factors which affect thermal efficiency and exhaust emissions were
deduced and their influences were discussed. In the final analysis it is
seen that there is an excellent agreement in all of these evaluations.
Abstract: In this paper, we present an innovative scheme of
blindly extracting message bits from an image distorted by an attack.
Support Vector Machine (SVM) is used to nonlinearly classify the
bits of the embedded message. Traditionally, a hard decoder is used
with the assumption that the underlying modeling of the Discrete
Cosine Transform (DCT) coefficients does not appreciably change.
In case of an attack, the distribution of the image coefficients is
heavily altered. The distribution of the sufficient statistics at the
receiving end corresponding to the antipodal signals overlap and a
simple hard decoder fails to classify them properly. We are
considering message retrieval of antipodal signal as a binary
classification problem. Machine learning techniques like SVM is
used to retrieve the message, when certain specific class of attacks is
most probable. In order to validate SVM based decoding scheme, we
have taken Gaussian noise as a test case. We generate a data set using
125 images and 25 different keys. Polynomial kernel of SVM has
achieved 100 percent accuracy on test data.
Abstract: Studies revealing the positive relationship between
trade and income are often criticized with the argument that
“development should mean more than rising incomes". Taking this
argument as a base and utilizing panel data, Davies and Quinlivan [1]
have demonstrated that increases in trade are positively associated
with future increases in social welfare as measured by the Human
Development Index (HDI). The purpose of this study is twofold:
Firstly, utilizing an income based country classification; it is aimed
to investigate whether the positive association between foreign trade
and HDI is valid within all country groups. Secondly, keeping the
same categorization as a base; it is aimed to reveal whether the
positive link between trade and HDI still exists when the income
components of the index are excluded. Employing a panel data
framework of 106 countries, this study reveals that the positive link
between trade and human development is valid only for high and
medium income countries. Moreover, the positive link between trade
and human development diminishes in lower-medium income
countries when only non-income components of the index are taken
into consideration.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetical and thermal stresses remain major failures for
insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: The selection for plantation of a particular type of
mustard plant depending on its productivity (pod yield) at the stage
of maturity. The growth of mustard plant dependent on some
parameters of that plant, these are shoot length, number of leaves,
number of roots and roots length etc. As the plant is growing, some
leaves may be fall down and some new leaves may come, so it can
not gives the idea to develop the relationship with the seeds weight at
mature stage of that plant. It is not possible to find the number of
roots and root length of mustard plant at growing stage that will be
harmful of this plant as roots goes deeper to deeper inside the land.
Only the value of shoot length which increases in course of time can
be measured at different time instances. Weather parameters are
maximum and minimum humidity, rain fall, maximum and minimum
temperature may effect the growth of the plant. The parameters of
pollution, water, soil, distance and crop management may be
dominant factors of growth of plant and its productivity. Considering
all parameters, the growth of the plant is very uncertain, fuzzy
environment can be considered for the prediction of shoot length at
maturity of the plant. Fuzzification plays a greater role for
fuzzification of data, which is based on certain membership
functions. Here an effort has been made to fuzzify the original data
based on gaussian function, triangular function, s-function,
Trapezoidal and L –function. After that all fuzzified data are
defuzzified to get normal form. Finally the error analysis
(calculation of forecasting error and average error) indicates the
membership function appropriate for fuzzification of data and use to
predict the shoot length at maturity. The result is also verified using
residual (Absolute Residual, Maximum of Absolute Residual, Mean
Absolute Residual, Mean of Mean Absolute Residual, Median of
Absolute Residual and Standard Deviation) analysis.
Abstract: Image compression is one of the most important
applications Digital Image Processing. Advanced medical imaging
requires storage of large quantities of digitized clinical data. Due to
the constrained bandwidth and storage capacity, however, a medical
image must be compressed before transmission and storage. There
are two types of compression methods, lossless and lossy. In Lossless
compression method the original image is retrieved without any
distortion. In lossy compression method, the reconstructed images
contain some distortion. Direct Cosine Transform (DCT) and Fractal
Image Compression (FIC) are types of lossy compression methods.
This work shows that lossy compression methods can be chosen for
medical image compression without significant degradation of the
image quality. In this work DCT and Fractal Compression using
Partitioned Iterated Function Systems (PIFS) are applied on different
modalities of images like CT Scan, Ultrasound, Angiogram, X-ray
and mammogram. Approximately 20 images are considered in each
modality and the average values of compression ratio and Peak
Signal to Noise Ratio (PSNR) are computed and studied. The quality
of the reconstructed image is arrived by the PSNR values. Based on
the results it can be concluded that the DCT has higher PSNR values
and FIC has higher compression ratio. Hence in medical image
compression, DCT can be used wherever picture quality is preferred
and FIC is used wherever compression of images for storage and
transmission is the priority, without loosing picture quality
diagnostically.