Abstract: Use of fly ash as a supplementary cementing material
in large volumes can bring both technological and economic benefits
for concrete industry. In this investigation mix proportions for high
volume fly ash concrete were determined at cement replacement
levels of 50%, 55%, 60% and 65% with low calcium fly ash. Flexural
and compressive strengths of different mixes were measured at ages
of 7, 28 and 90 days. Flexural strength of composite section prepared
from pavement quality and lean high volume fly ash concrete was
determined at the age of 28 days. High volume fly ash concrete mixes
exhibited higher rate of strength gain and age factors than
corresponding reference concrete mixes. The optimum cement
replacement level for pavement quality concrete was found to be
60%. The consideration of bond between pavement quality and lean
of high volume fly ash concrete will be beneficial in design of rigid
pavements.
Abstract: Ultrastructure of duodenum mucosa of irradiated rat
was studied versus dose rate of irradiation following exposure to
gamma rays from 60-Cobalt source. The animals were whole body
irradiated at two dose rates (1 Gy.mn-1 and 1 Gy.h-1) and three total
doses (1, 2 or 4 Gy) for each dose rate. 24 or 48 h after irradiation,
their small intestine was removed and samples of duodenum were
processed for observations under a transmission electron microscopy.
Samples of duodenum mucosa of control rats were processed in the
same way. For the lower dose rate of 1 Gy.h-1, main lesions
characteristic of apoptosis were detected within irradiated enterocytes
at a total dose of 2 Gy and 24 h after exposure. Necrosis was noted in
the samples, 48 h after exposition. For the higher dose rate of 1
Gy.mn-1, fewer changes were detected at all total doses 24 or 48 h
irradiation. Thus, it was shown that the appearance of radiationinduced
alterations varies not only with increasing total dose and
post-irradiation time but especially with decreasing dose rate.
Abstract: Rooted in the study of social functioning of space in architecture, Space Syntax (SS) and the more recent Network Pattern (NP) researches demonstrate the 'spatial structures' of city, i.e. the hierarchical patterns of streets, junctions and alley ends. Applying SS and NP models, planners can conceptualize the real city-s patterns. Although, both models yield the optimal path of the city their underpinning displays of the city-s spatial configuration differ. The Axial Map analyzes the topological non-distance-based connectivity structure, whereas, the Central-Node Map and the Shortcut-Path Map, in contrast, analyze the metrical distance-based structures. This research contrasts and combines them to understand various forms of city-s structures. It concludes that, while they reveal different spatial structures, Space Syntax and Network Pattern urban models support each the other. Combining together they simulate the global access and the locally compact structures namely the central nodes and the shortcuts for the city.
Abstract: Sunflower stalks were analysed for chemical
compositions: pentosan 15.84%, holocellulose 70.69%,
alphacellulose 45.74%, glucose 27.10% and xylose 7.69% based on
dry weight of 100-g raw material. The most optimum condition for
steam explosion pretreatment was as follows. Sunflower stalks were
cut into small pieces and soaked in 0.02 M H2SO4 for overnight.
After that, they were steam exploded at 207 C and 21 kg/cm2 for 3
minutes to fractionate cellulose, hemicellulose and lignin. The
resulting hydrolysate, containing hemicellulose, and cellulose pulp
contained xylose sugar at 2.53% and 7.00%, respectively.The pulp
was further subjected to enzymatic saccharification at 50 C, pH 4.8 citrate buffer) with pulp/buffer 6% (w/w)and Celluclast 1.5L/pulp
2.67% (w/w) to obtain single glucose with maximum yield 11.97%.
After fixed-bed fermentation under optimum condition using
conventional yeast mixtures to produce bioethanol, it indicated
maximum ethanol yield of 0.028 g/100 g sunflower stalk.
Abstract: We present a label-free biosensor based on
electrochemical impedance spectroscopy for the detection of proinflammatory
cytokine Tumor Necrosis Factor (TNF-α). Secretion of
TNF-α has been correlated to the onset of various diseases including
rheumatoid arthritis, Crohn-s disease etc. Gold electrodes were
patterned on a silicon substrate and self assembled monolayer of
dithiobis-succinimidyl propionate was used to develop the biosensor
which achieved a detection limit of ~57fM. A linear relationship was
also observed between increasing TNF-α concentrations and chargetransfer
resistance within a dynamic range of 1pg/ml – 1ng/ml.
Abstract: This paper describes a new approach of classification
using genetic programming. The proposed technique consists of
genetically coevolving a population of non-linear transformations on
the input data to be classified, and map them to a new space with a
reduced dimension, in order to get a maximum inter-classes
discrimination. The classification of new samples is then performed
on the transformed data, and so become much easier. Contrary to the
existing GP-classification techniques, the proposed one use a
dynamic repartition of the transformed data in separated intervals, the
efficacy of a given intervals repartition is handled by the fitness
criterion, with a maximum classes discrimination. Experiments were
first performed using the Fisher-s Iris dataset, and then, the KDD-99
Cup dataset was used to study the intrusion detection and
classification problem. Obtained results demonstrate that the
proposed genetic approach outperform the existing GP-classification
methods [1],[2] and [3], and give a very accepted results compared to
other existing techniques proposed in [4],[5],[6],[7] and [8].
Abstract: Microbubbbles incorporating ultrasound have been used to increase the efficacy of targeted drug delivery, because microstreaming induced by cavitating bubbles affects the drug perfusion into the target cells and tissues. In order to clarify the physical effects of microstreaming on drug perfusion into tissues, a preliminary experimental study of perfusion enhancement by a stably oscillating microbubble was performed. Microstreaming was induced by an oscillating bubble at 15 kHz, and perfusion of dye into an agar phantom was optically measured by histology on agar phantom. Surface color intensity and the penetration length of dye in the agar phantom were increased more than 70% and 30%, respectively, due to the microstreaming induced by an oscillating bubble. The mass of dye perfused into a tissue phantom for 30 s was increased about 80% in the phantom with an oscillating bubble. This preliminary experiment shows the physical effects of steady streaming by an oscillating bubble can enhance the drug perfusion into the tissues while minimizing the biological effects.
Abstract: Despite the relatively large number of studies that
have examined the use of appeals in advertisements, research on the
use of appeals in green advertisements is still underdeveloped and
needs to be investigated further, as it is definitely a tool for marketers
to create illustrious ads. In this study, content analysis was employed
to examine the nature of green advertising appeals and to match the
appeals with the green advertisements. Two different types of green
print advertisings, product orientation and organizational image
orientation were used. Thirty highly educated participants with
different backgrounds were asked individually to ascertain three
appeals out of thirty-four given appeals found among forty real green
advertisements. To analyze participant responses and to group them
based on common appeals, two-step K-mean clustering is used. The
clustering solution indicates that eye-catching graphics and
imaginative appeals are highly notable in both types of green ads.
Depressed, meaningful and sad appeals are found to be highly used in
organizational image orientation ads, whereas, corporate image,
informative and natural appeals are found to be essential for product
orientation ads.
Abstract: Application of pesticides in the paddy fields has
deleterious effects on non-target organisms including cyanobacteria
which are photosynthesizing and nitrogen fixing micro-organisms
contributing significantly towards soil fertility and crop yield.
Pesticide contamination in the paddy fields has manifested into a
serious global environmental concern. To study the effect of one such
pesticide, three cyanobacterial strains; Anabaena fertilissima,
Aulosira fertilissima and Westiellopsis prolifica were selected for
their stress responses to an Organochlorine insecticide - 6, 7, 8, 9, 10,
10-hexachloro-1, 5, 5a, 6, 9, 9a-hexahydro-6, 9-methano-2, 4, 3-
benzodioxathiepine-3-oxide, with reference to their photosynthesic
pigments-chlorophyll-a and carotenoids as well as accessory
pigments-phycobiliproteins (phycocyanin, allophycocyanin and
phycoerythrin), stress induced biochemical metabolites like
carbohydrates, proteins, amino acids, phenols and enzymes-nitrate
reductase, glutamine synthetase and succinate dehydrogenase. All
the three cyanobacterial strains were adversely affected by the
insecticide doses and inhibition was dose dependent. Reduction in
photosynthetic and accessory pigments, metabolites, nitrogen fixing
and respiratory enzymes of the test organisms were accompanied
with an initial increase in their total protein at lower Organochlorine
doses. On the other hand, increased amount of phenols in all the
insecticide treated concentrations was indicative of stressed activities
of the organisms.
Abstract: High performance Resistive Random Access Memory
(RRAM) based on HfOx has been prepared and its temperature
instability has been investigated in this work. With increasing
temperature, it is found that: leakage current at high resistance state
increases, which can be explained by the higher density of traps
inside dielectrics (related to trap-assistant tunneling), leading to a
smaller On/Off ratio; set and reset voltages decrease, which may be
attributed to the higher oxygen ion mobility, in addition to the
reduced potential barrier to create / recover oxygen ions (or oxygen
vacancies); temperature impact on the RRAM retention degradation
is more serious than electrical bias.
Abstract: An on-line condition monitoring method for transmission line is proposed using electrical circuit theory and IT technology in this paper. It is reasonable that the circuit parameters such as resistance (R), inductance (L), conductance (g) and capacitance (C) of a transmission line expose the electrical conditions and physical state of the line. Those parameters can be calculated from the linear equation composed of voltages and currents measured by synchro-phasor measurement technique at both end of the line. A set of linear voltage drop equations containing four terminal constants (A, B ,C ,D ) are mathematical models of the transmission line circuits. At least two sets of those linear equations are established from different operation condition of the line, they may mathematically yield those circuit parameters of the line. The conditions of line connectivity including state of connecting parts or contacting parts of the switching device may be monitored by resistance variations during operation. The insulation conditions of the line can be monitored by conductance (g) and capacitance(C) measurements. Together with other condition monitoring devices such as partial discharge, sensors and visual sensing device etc.,they may give useful information to monitor out any incipient symptoms of faults. The prototype of hardware system has been developed and tested through laboratory level simulated transmission lines. The test has shown enough evident to put the proposed method to practical uses.
Abstract: Cyprus- offshore aquaculture industry has promising
prospects taking into account that Cyprus is an island. Its production
trend is increasing overtaking bigger countries such Greece and Italy.
However, current mooring systems seem to be under-performing
acting as obstacles for its future development. Furthermore, shallow
coastal waters scarcity due to competing industries dictates future
development to come by moving further from shore exposing fish
farms and subsequently mooring systems to harsher environmental
loadings. It is, therefore, of paramount importance to design mooring
systems based on engineering and scientific principles and leave
behind the present “trial and error" methods. This paper presents the
current state of Cyprus- offshore aquaculture industry and focuses of
its mooring designs by proposing a new methodology for designing
more reliable systems, hence ensuring its future.
Abstract: In the control theory one attempts to find a controller
that provides the best possible performance with respect to some
given measures of performance. There are many sorts of controllers
e.g. a typical PID controller, LQR controller, Fuzzy controller etc. In
the paper will be introduced polynomial controller with novel tuning
method which is based on the special pole placement encoding
scheme and optimization by Genetic Algorithms (GA). The examples
will show the performance of the novel designed polynomial
controller with comparison to common PID controller.
Abstract: In recent years, several severe large-scale influenza
outbreaks happened in many countries, such as SARS in 2005 or
H1N1 in 2009. Those influenza Epidemics have greatly impacts not
only on people-s life and health, but medical systems in different
countries. Although severe diseases are more experienced, they are not
fully controlled. Governments have different policies to control the
spreads of diseases. However, those policies have both positive and
negative social or economical influence on people and society.
Therefore, it is necessary and essential to develop an appropriate
model for evaluations of policies. Consequently, a proper measure can
be implemented to confront the diseases. The main goal of this study is
to develop a SIR-based model for the further evaluations of the
candidate policies during the influenza outbreaks.
Abstract: Most real world systems express themselves formally
as a set of nonlinear algebraic equations. As applications grow, the
size and complexity of these equations also increase. In this work, we
highlight the key concepts in using the homotopy analysis method
as a methodology used to construct efficient iteration formulas for
nonlinear equations solving. The proposed method is experimentally
characterized according to a set of determined parameters which
affect the systems. The experimental results show the potential and
limitations of the new method and imply directions for future work.
Abstract: The Želazny Most tailing pond is one of the largest
facilities worldwide for waste disposal from the copper mines located
in South-West Poland. A potential failure of the dam would allow
more than 10 million cubic meters of contaminated slurry to flow to
the valley, causing immense environmental problems to the
surrounding area. Thus, the determination of the strength properties
of the dam's soils and their variability is of utmost importance.
An extensive site investigation consisting of more than 480 cone
penetration tests (CPTs) with or without pore water pressure
measurements were conducted within a period of 13 years to study
the mechanical properties of the tailings body. The present work
investigates the point variability of the soil strength parameters
(effective friction angle
Abstract: Nowadays, one of the most important problems of the
metropolises and the world large cities is the habitant traffic difficulty
and lack of sufficient parking site for the vehicles. Esfahan city as the
third metropolis of Iran has encountered with the vehicles parkingplace
problems in the most parts of fourteen regions of the city. The
non principled and non systematic dispersal and lack of parking sites
in the city has created an unfavorable status for its traffic and has
caused the air and sound pollutions increase; in addition, it wastes the
most portions of the citizenship and travelers' charge and time in
urban pathways and disturbs their mental and psychical calmness,
thus leads to their intensive dissatisfaction. In this study, by the usage
of AHP model in GIS environment, the effective criteria in selecting
the public parking sites have been combined with each other, and the
results of the created layers overlapping represent the parking
utilitarian vastness and widths. The achieved results of this research
indicate the pretty appropriate public parking sites selection in region
number 3 of Esfahan; but inconsequential dispersal and lack of these
parking sites in this region have caused abundant transportation
problems in Esfahan city.
Abstract: Nowadays, manufacturers are facing great challenges
with regard to the production of green products due to the emerging issue of hazardous substance management (HSM). In particular,
environmental legislation pressures have yielded to increased risk,
manufacturing complexity and green components demands. The green principles were expanded to many departments within
organization, including supply chain. Green supply chain
management (GSCM) was emerging in the last few years. This idea
covers every stage in manufacturing from the first to the last stage of
life cycle. From product lifecycle concept, the cycle starts at the design of a product. QFD is a customer-driven product development
tool, considered as a structured management approach for efficiently
translating customer needs into design requirements and parts deployment, as well as manufacturing plans and controls in order to
achieve higher customer satisfaction. This paper develops an Eco-
QFD to provide a framework for designing Eco-mobile phone by integrating the life cycle analysis LCA into QFD throughout the entire product development process.
Abstract: This paper describes the performance of TCP Vegas
over the wireless IPv6 network. The performance of TCP Vegas is
evaluated using network simulator (ns-2). The simulation experiment
investigates how packet spacing affects the network delay, network
throughput and network efficiency of TCP Vegas. Moreover, we
investigate how the variable FTP packet sizes affect the network
performance. The result of the simulation experiment shows that as
the packet spacing is implements, the network delay is reduces,
network throughput and network efficiency is optimizes. As the FTP
packet sizes increase, the ratio of delay per throughput decreases.
From the result of experiment, we propose the appropriate packet size
in transmitting file transfer protocol application using TCP Vegas
with packet spacing enhancement over wireless IPv6 environment in
ns-2. Additionally, we suggest the appropriate ratio in determining
the appropriate RTT and buffer size in a network.
Abstract: Realistic 3D face model is more precise in representing
pose, illumination, and expression of face than 2D face model so that it
can be utilized usefully in various applications such as face recognition,
games, avatars, animations, and etc.
In this paper, we propose a 3D face modeling method based on 3D
dense morphable shape model. The proposed 3D modeling method
first constructs a 3D dense morphable shape model from 3D face scan
data obtained using a 3D scanner. Next, the proposed method extracts
and matches facial landmarks from 2D image sequence containing a
face to be modeled, and then reconstructs 3D vertices coordinates of
the landmarks using a factorization-based SfM technique. Then, the
proposed method obtains a 3D dense shape model of the face to be
modeled by fitting the constructed 3D dense morphable shape model
into the reconstructed 3D vertices. Also, the proposed method makes a
cylindrical texture map using 2D face image sequence. Finally, the
proposed method generates a 3D face model by rendering the 3D dense
face shape model using the cylindrical texture map. Through building
processes of 3D face model by the proposed method, it is shown that
the proposed method is relatively easy, fast and precise.