Abstract: This paper presents a physics-based model for the
high-voltage fast recovery diodes. The model provides a good
trade-off between reverse recovery time and forward voltage drop
realized through a combination of lifetime control and emitter
efficiency reduction techniques. The minority carrier lifetime can be
extracted from the reverse recovery transient response and forward
characteristics. This paper also shows that decreasing the amount of
the excess carriers stored in the drift region will result in softer
characteristics which can be achieved using a lower doping level. The
developed model is verified by experiment and the measurement data
agrees well with the model.
Abstract: Supersonic open and closed cavity flows are investigated experimentally and computationally. Free stream Mach number of two is set. Schlieren imaging is used to visualise the flow behaviour showing stark differences between open and closed. Computational Fluid Dynamics (CFD) is used to simulate open cavity of flow with aspect ratio of 4. A rear wall treatment is implemented in order to pursue a simple passive control approach. Good qualitative agreement is achieved between the experimental flow visualisation and the CFD in terms of the expansion-shock waves system. The cavity oscillations are shown to be dominated by the first and third Rossister modes combining to high fluctuations of non-linear nature above the cavity rear edge. A simple rear wall treatment in terms of a hole shows mixed effect on the flow oscillations, RMS contours, and time history density fluctuations are given and analysed.
Abstract: A generic and extendible Multi-Agent Data Mining
(MADM) framework, MADMF (the Multi-Agent Data Mining
Framework) is described. The central feature of the framework is that
it avoids the use of agreed meta-language formats by supporting a
framework of wrappers.
The advantage offered is that the framework is easily extendible,
so that further data agents and mining agents can simply be added to
the framework. A demonstration MADMF framework is currently
available. The paper includes details of the MADMF architecture and
the wrapper principle incorporated into it. A full description and
evaluation of the framework-s operation is provided by considering
two MADM scenarios.
Abstract: Phaseolus coccineus L. is the third most important
cultivated Phaseolus species in the world. It is widely grown in
Latvia due to its earliness, good taste and uniform and qualitative
yield. Experiments were carried out in the laboratories of Department
of Food Technology and Agronomical Analysis Scientific Laboratory
at Latvia Universityof Agriculture. Beans (Phaseolus coccineus L.)
crude protein, crude ash content as well as colour measurements were
analyzed. Results show, that brown coloured beans have less crude
protein content than others, and ash content have significant
differences.
Abstract: This communication is intended to provide some issues for thought on the importance of implementation of Blended Learning in traditional universities, particularly in the Spanish university system. In this respect, we believe that virtual environments are likely to meet some of the needs raised by the Bologna agreement, trying to maintain the quality of teaching and at the same time taking advantage of the functionalities that virtual learning platforms offer. We are aware that an approach of learning from an open and constructivist nature in universities is a complex process that faces significant technological, administrative and human barriers. Therefore, in order to put plans in our universities, it is necessary to analyze the state of the art of some indicators relating to the use of ICT, with special attention to virtual teaching and learning, so that we can identify the main obstacles and design adaptive strategies for their full integration in the education system. Finally, we present major initiatives launched in the European and state framework for the effective implementation of new virtual environments in the area of higher education.
Abstract: In a metal forming process, the friction between the
material and the tools influences the process by modifying the stress
distribution of the workpiece. This frictional behaviour is often taken
into account by using a constant coefficient of friction in the finite
element simulations of sheet metal forming processes. However,
friction coefficient varies in time and space with many parameters.
The Stribeck friction model is investigated in this study to predict
springback behaviour of AA6061-T4 sheets during V-bending
process. The coefficient of friction in Stribeck curve depends on
sliding velocity and contact pressure. The plane-strain bending
process is simulated in ABAQUS/Standard. We compared the
computed punch load-stroke curves and springback related to the
constant coefficient of friction with the defined friction model. The
results clearly showed that the new friction model provides better
agreement between experiments and results of numerical simulations.
The influence of friction models on stress distribution in the
workpiece is also studied numerically
Abstract: We investigate nonfactorizable contributions to
D → ¤Ç¤Ç decay modes. We perform isospin analysis of the
nonfactorizable contributions to these decays. Obtaining the
factorizable contributions from spectator-quark diagrams using
= 3 C N , we determine nonfactorizable amplitudes for these decays
and predict their branching ratios.
Abstract: An attempt has been made to develop a
seminumerical model to study temperature variations in dermal
layers of human limbs. The model has been developed for two
dimensional steady state case. The human limb has been assumed to
have elliptical cross section. The dermal region has been divided
into three natural layers namely epidermis, dermis and subdermal
tissues. The model incorporates the effect of important physiological
parameters like blood mass flow rate, metabolic heat generation, and
thermal conductivity of the tissues. The outer surface of the limb is
exposed to the environment and it is assumed that heat loss takes
place at the outer surface by conduction, convection, radiation, and
evaporation. The temperature of inner core of the limb also varies at
the lower atmospheric temperature. Appropriate boundary conditions
have been framed based on the physical conditions of the problem.
Cubic splines approach has been employed along radial direction and
Fourier series along angular direction to obtain the solution. The
numerical results have been computed for different values of
eccentricity resembling with the elliptic cross section of the human
limbs. The numerical results have been used to obtain the
temperature profile and to study the relationships among the various
physiological parameters.
Abstract: This paper presents an approach for the determination of the optimal cutting parameters (spindle speed, feed rate, depth of cut and engagement) leading to minimum surface roughness in face milling of high silicon stainless steel by coupling neural network (NN) and Electromagnetism-like Algorithm (EM). In this regard, the advantages of statistical experimental design technique, experimental measurements, artificial neural network, and Electromagnetism-like optimization method are exploited in an integrated manner. To this end, numerous experiments on this stainless steel were conducted to obtain surface roughness values. A predictive model for surface roughness is created by using a back propogation neural network, then the optimization problem was solved by using EM optimization. Additional experiments were performed to validate optimum surface roughness value predicted by EM algorithm. It is clearly seen that a good agreement is observed between the predicted values by EM coupled with feed forward neural network and experimental measurements. The obtained results show that the EM algorithm coupled with back propogation neural network is an efficient and accurate method in approaching the global minimum of surface roughness in face milling.
Abstract: Binary Decision Diagrams (BDDs) are useful data
structures for symbolic Boolean manipulations. BDDs are used in
many tasks in VLSI/CAD, such as equivalence checking, property
checking, logic synthesis, and false paths. In this paper we describe a
new approach for the realization of a BDD package. To perform
manipulations of Boolean functions, the proposed approach does not
depend on the recursive synthesis operation of the IF-Then-Else
(ITE). Instead of using the ITE operation, the basic synthesis
algorithm is done using Boolean NOR operation.
Abstract: This paper presents how the real-time chatter
prevention can be realized by feedback of acoustic cutting signal, and
the efficacy of the proposed adaptive spindle speed tuning algorithm is
verified by intensive experimental simulations. A pair of
microphones, perpendicular to each other, is used to acquire the
acoustic cutting signal resulting from milling chatter. A real-time
feedback control loop is constructed for spindle speed compensation
so that the milling process can be ensured to be within the stability
zone of stability lobe diagram. Acoustic Chatter Signal Index (ACSI)
and Spindle Speed Compensation Strategy (SSCS) are proposed to
quantify the acoustic signal and actively tune the spindle speed
respectively. By converting the acoustic feedback signal into ACSI,
an appropriate Spindle Speed Compensation Rate (SSCR) can be
determined by SSCS based on real-time chatter level or ACSI.
Accordingly, the compensation command, referred to as Added-On
Voltage (AOV), is applied to increase/decrease the spindle motor
speed. By inspection on the precision and quality of the workpiece
surface after milling, the efficacy of the real-time chatter prevention
strategy via acoustic signal feedback is further assured.
Abstract: The results of an experimental study of the process of
convective and boiling heat transfer in the vessel with stirrer for
smooth and rough ring-shaped pipes are presented. It is established
that creation of two-dimensional artificial roughness on the heated
surface causes the essential (~100%) intensification of convective
heat transfer. In case of boiling the influence of roughness appears on
the initial stage of boiling and in case of fully developed nucleate
boiling there was no intensification of heat transfer. The similitude
equation for calculating convective heat transfer coefficient, which
generalizes well experimental data both for the smooth and the rough
surfaces is proposed.
Abstract: The effect of flooding can be a serious problem for
wheat farmers, even at dry land condition. Amount of flooding
damage depends on duration flooding, developmental stage, wheat
type and variety. Therefore as a factorial experiment in randomized
complete design based on winter bread wheat cultivars (Pishtaz,
Marvdasht, Shiraz, Zarin, Shahriar, C-81-4, Sardari, Agosta seed,
FGS and Azar2) at stages (Non- flooding stress, flooding at tillering
and stem elongation stages for 15 days) carried out in Faculty of
Agriculture, Razi University, Kermanshah, Iran. During flooding,
soil environment of plant roots were water saturated. Analysis of
variance showed that flooding had a significant effect on the number
of grains per spike, grain weight per spike and a grain weight. Hence
flooding reduces the number of grain per spike between 27.1 to 42.5
percent, grain weight per spike between 34.7 to 54.4 percent and
single grain weight between 12.1 to 15.1 percent. Effects of flooding
at the tillering stage reduced higher than stem elongation stage on
studied traits. The result also showed that flooding at tillering stage
delayed spikelet primordial and floret. Between wheat cultivars was
significant for traits, but were different reactions. "Shiraz", "Zarin"
and "Shahriar" had the most no. grain per spike, but "Zarin" and
"Sardari" had the most grain weight per spike and single grain
weight, respectively. Also, interaction between start of flooding and
cultivar was significant.
Abstract: In this paper, an efficient wave concept iterative
process (WCIP) with auxiliary Sources is presented for full wave
investigation of an active microwave structure on micro strip
technology. Good agreement between the experimental and
simulation results is observed.
Abstract: A SnO2/CdS/CdTe heterojunction was fabricated by
thermal evaporation technique. The fabricated cells were annealed at
573K for periods of 60, 120 and 180 minutes. The structural
properties of the solar cells have been studied by using X-ray
diffraction. Capacitance- voltage measurements were studied for the
as-prepared and annealed cells at a frequency of 102 Hz. The
capacitance- voltage measurements indicated that these cells are
abrupt. The capacitance decreases with increasing annealing time.
The zero bias depletion region width and the carrier concentration
increased with increasing annealing time. The carrier transport
mechanism for the CdS/CdTe heterojunction in dark is tunneling
recombination. The ideality factor is 1.56 and the reverse bias
saturation current is 9.6×10-10A. The energy band lineup for the n-
CdS/p-CdTe heterojunction was investigated using current - voltage
and capacitance - voltage characteristics.
Abstract: In this paper, the significant wave height at the Upper Gulf of Thailand and the changing of wave height at Bangkhuntien shoreline were simulated by using the Simulating WAves Nearshore Model (SWAN) version 40.51. The simulated results indicated that the significant wave height by SWAN model corresponded with the observed data. The results showed that the maximum significant wave height at the Bangkhuntien shoreline were 1.06-2.05 m. and the average significant wave height at the Bangkhuntien shoreline were 0.30-0.47 m. The significant wave height can be used to calculate the erosion through the Bangkhuntien shoreline. The erosion rates at the Bangkhuntien shoreline were prepared by using the aerial photo and they were about 1.80 m/yr. from 1980- 1986, 4.75 m/yr from 1987-1993, 15.28 m/yr from 1994-1996 and 10.03 m/yr from 1997-2002. The relation between the wave energy and the erosion were in good agreement. Therefore, the significant wave height was one of the major factors of the erosion at the Bangkhuntien shoreline.
Abstract: This study analyzes characteristics determining
member’s willingness to invest in cooperatives using ordered logit
model. The data were collected in a field survey among 122
cooperative members in north-central China. The descriptive analysis
of survey evidence suggests that cooperatives in China generally
having poor ability to deliver the processing services related to
product package, grading, and storage, performing worse in
profitability, inability of providing returns to capital and obtaining
agricultural loan. The regression results demonstrate that members’
farm size, their satisfaction with cooperative price preferential
services, attitudes toward cooperative operational scale and
development potential have statistically significant impact on
willingness to invest.
Abstract: This paper presents a conceptual model of agreement
options on negotiation support for civil engineering decision. The
negotiation support facilitates the solving of group choice decision
making problems in civil engineering decision to reduce the impact
of mud volcano disaster in Sidoarjo, Indonesia. The approach based
on application of analytical hierarchy process (AHP) method for
multi criteria decision on three level of decision hierarchy.
Decisions for reducing impact is very complicated since many
parties involved in a critical time. Where a number of stakeholders
are involved in choosing a single alternative from a set of solution
alternatives, there are different concern caused by differing
stakeholder preferences, experiences, and background. Therefore, a
group choice decision support is required to enable each stakeholder
to evaluate and rank the solution alternatives before engaging into
negotiation with the other stakeholders. Such civil engineering
solutions as alternatives are referred to as agreement options that are
determined by identifying the possible stakeholder choice, followed
by determining the optimal solution for each group of stakeholder.
Determination of the optimal solution is based on a game theory
model of n-person general sum game with complete information that
involves forming coalitions among stakeholders.
Abstract: Today, incorrect use of lands and land use changes,
excessive grazing, no suitable using of agricultural farms, plowing on
steep slopes, road construct, building construct, mine excavation etc
have been caused increasing of soil erosion and sediment yield. For
erosion and sediment estimation one can use statistical and empirical
methods. This needs to identify land unit map and the map of
effective factors. However, these empirical methods are usually time
consuming and do not give accurate estimation of erosion. In this
study, we applied GIS techniques to estimate erosion and sediment of
Menderjan watershed at upstream Zayandehrud river in center of
Iran. Erosion faces at each land unit were defined on the basis of land
use, geology and land unit map using GIS. The UTM coordinates of
each erosion type that showed more erosion amounts such as rills and
gullies were inserted in GIS using GPS data. The frequency of
erosion indicators at each land unit, land use and their sediment yield
of these indices were calculated. Also using tendency analysis of
sediment yield changes in watershed outlet (Menderjan hydrometric
gauge station), was calculated related parameters and estimation
errors. The results of this study according to implemented watershed
management projects can be used for more rapid and more accurate
estimation of erosion than traditional methods. These results can also
be used for regional erosion assessment and can be used for remote
sensing image processing.
Abstract: The authors present optimization parameters of rotary
positioner controller in hard disk drive servo track writing process
using coefficient diagram method; CDM. Due to estimation
parameters in PI Positioning Control System by expected ratio
method cannot meet the required specification of response
effectively, we suggest coefficient diagram method for defining
controller parameters under the requirement of the system. Finally,
the simulation results show that our proposed method can improve
the problem in tuning parameter of rotary positioner controller. It is
satisfied specification of performance of control system. Furthermore,
it is very convenient as a fast adjustment damping ratio as well as a
high speed response.