Abstract: The intelligent fuzzy input estimator is used to estimate
the input force of the rigid bar structural system in this study. The
fuzzy Kalman filter without the input term and the fuzzy weighting
recursive least square estimator are two main portions of this method.
The practicability and accuracy of the proposed method were verified
with numerical simulations from which the input forces of a rigid bar
structural system were estimated from the output responses. In order to
examine the accuracy of the proposed method, a rigid bar structural
system is subjected to periodic sinusoidal dynamic loading. The
excellent performance of this estimator is demonstrated by comparing
it with the use of difference weighting function and improper the
initial process noise covariance. The estimated results have a good
agreement with the true values in all cases tested.
Abstract: A reduced order modeling approach for natural
gas transient flow in pipelines is presented. The Euler
equations are considered as the governing equations and
solved numerically using the implicit Steger-Warming flux
vector splitting method. Next, the linearized form of the
equations is derived and the corresponding eigensystem is
obtained. Then, a few dominant flow eigenmodes are used to
construct an efficient reduced-order model. A well-known test
case is presented to demonstrate the accuracy and the
computational efficiency of the proposed method. The results
obtained are in good agreement with those of the direct
numerical method and field data. Moreover, it is shown that
the present reduced-order model is more efficient than the
conventional numerical techniques for transient flow analysis
of natural gas in pipelines.
Abstract: In this paper, the 1-D conduction-radiation problem is solved by the lattice Boltzmann method. The effects of various parameters such as the scattering albedo, the conduction–radiation parameter and the wall emissivity are studied. In order to check on the accuracy of the numerical technique employed for the solution of the considered problem, the present numerical code was validated with the published study. The found results are in good agreement with those published
Abstract: Numerical calculations of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann method at Reynolds number 150. The effects of upstream locations, downstream locations and blockage are investigated systematically. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The results had shown that the upstream, downstream and height of the computational domain are at least 7.5, 37.5 and 12 diameters of the cylinder, respectively.
Abstract: The evolution of current modeling specifications gives rise to the problem of generating automated test cases from a variety of application tools. Past endeavours on behavioural testing of UML statecharts have not systematically leveraged the potential of existing graph theory for testing of objects. Therefore there exists a need for a simple, tool-independent, and effective method for automatic test generation. An architecture, codenamed ACUTE-J (Automated stateChart Unit Testing Engine for Java), for automating the unit test generation process is presented. A sequential approach for converting UML statechart diagrams to JUnit test classes is described, with the application of existing graph theory. Research byproducts such as a universal XML Schema and API for statechart-driven testing are also proposed. The result from a Java implementation of ACUTE-J is discussed in brief. The Chinese Postman algorithm is utilised as an illustration for a run-through of the ACUTE-J architecture.
Abstract: In order to study of hydropriming and halopriming on
germination and early growth stage of wheat (Triticum aestivum) an
experiment was carried out in laboratory of the Department of
Agronomy and Plant breeding, Shahrood University of Technology.
Seed treatments consisted of T1: control (untreated seeds), T2:
soaking in distilled water for 18 h (hydropriming). T3: soaking in -
1.2 MPa solution of CaSO4 for 36 h (halopriming). Germination and
early seedling growth were studied using distilled water (control) and
under osmotic potentials of -0.4, -0.8 and -1.2 MPa for NaCl and
polyethylene glycol (PEG 6000), respectively. Results showed that
Hydroprimed seeds achieved maximum germination seedling dry
weight, especially during the higher osmotic potentials. Minimum
germination was recorded at untreated seeds (control) followed by
osmopriming. Under high osmotic potentials, hydroprimed seeds had
higher GI (germination index) as compared to haloprimed or
untreated seeds. Interaction effect of seed treatment and osmotic
potential significantly affected the seedling vigour index (SVI).
Abstract: Real-time measurement of applied forces, like tension, compression, torsion, and bending moment, identifies the transferred energies being applied to the bottomhole assembly (BHA). These forces are highly detrimental to measurement/logging-while-drilling tools and downhole equipment. Real-time measurement of the dynamic downhole behavior, including weight, torque, bending on bit, and vibration, establishes a real-time feedback loop between the downhole drilling system and drilling team at the surface. This paper describes the numerical analysis of the strain data acquired by the measurement tool at different locations on the strain pockets. The strain values obtained by FEA for various loading conditions (tension, compression, torque, and bending moment) are compared against experimental results obtained from an identical experimental setup. Numerical analyses results agree with experimental data within 8% and, therefore, substantiate and validate the FEA model. This FEA model can be used to analyze the combined loading conditions that reflect the actual drilling environment.
Abstract: Bone material is treated as heterogeneous and hierarchical in nature therefore appropriate size of bone specimen is required to analyze its tensile properties at a particular hierarchical level. Tensile properties of cortical bone are important to investigate the effect of drug treatment, disease and aging as well as for development of computational and analytical models. In the present study tensile properties of buffalo as well as goat femoral and tibiae cortical bone are analyzed using sub-size tensile specimens. Femoral cortical bone was found to be stronger in tension as compared to the tibiae cortical bone and the tensile properties obtained using sub-size specimens show close resemblance with the tensile properties of full-size cortical specimens. A two dimensional finite element (FE) modal was also applied to simulate the tensile behavior of sub-size specimens. Good agreement between experimental and FE model was obtained for sub-size tensile specimens of cortical bone.
Abstract: In technological processes, in addition to the main
product, result a large amount of materials, called wastes, but due to
the possibilities of recovery, by means of recycling and reusing it can
fit in the category of by-products. These large amounts of dust from
the steel industry are a major problem in terms of environmental and
human health, landscape, etc. Solving these problems, the impressive
amounts of waste can be done through their proper management and
recovery for every type of waste. In this article it was watched the
capitalizing through pelleting and briquetting of small and powdery
waste aiming to obtain the sponge iron as raw material, used in blast
furnaces and electric arc furnaces. The data have been processed in
the Excel spreadsheet program, being presented in the form of
diagrams.
Abstract: It is shown that a modified UNIFAC model can be
applied to predict solubility of hydrocarbon gases and vapors in
hydrocarbon solvents. Very good agreement with experimental data
has been achieved. In this work we try to find best way for predicting
dimethyl ether solubility in liquid paraffin by using group
contribution theory.
Abstract: To define or predict incipient motion in an alluvial
channel, most of the investigators use a standard or modified form of
Shields- diagram. Shields- diagram does give a process to determine
the incipient motion parameters but an iterative one. To design
properly (without iteration), one should have another equation for
resistance. Absence of a universal resistance equation also magnifies
the difficulties in defining the model. Neural network technique,
which is particularly useful in modeling a complex processes, is
presented as a tool complimentary to modeling incipient motion.
Present work develops a neural network model employing the RBF
network to predict the average velocity u and water depth y based on
the experimental data on incipient condition. Based on the model,
design curves have been presented for the field application.
Abstract: A highly optimized implementation of binary mixture
diffusion with no initial bulk velocity on graphics processors is
presented. The lattice Boltzmann model is employed for simulating
the binary diffusion of oxygen and nitrogen into each other with
different initial concentration distributions. Simulations have been
performed using the latest proposed lattice Boltzmann model that
satisfies both the indifferentiability principle and the H-theorem for
multi-component gas mixtures. Contemporary numerical
optimization techniques such as memory alignment and increasing
the multiprocessor occupancy are exploited along with some novel
optimization strategies to enhance the computational performance on
graphics processors using the C for CUDA programming language.
Speedup of more than two orders of magnitude over single-core
processors is achieved on a variety of Graphical Processing Unit
(GPU) devices ranging from conventional graphics cards to
advanced, high-end GPUs, while the numerical results are in
excellent agreement with the available analytical and numerical data
in the literature.
Abstract: Experiments have been carried out at the Latvia
University of Agriculture Department of Food Technology. The aim
of this work was to assess the effect of sous vide packaging during
the storage time of salad with meat in mayonnaise at different storage
temperature. Samples were evaluated at 0, 1, 3, 7, 10, 15, 18, 25, 29,
42, and 52 storage days at the storage temperature of +4±0.5 ºC and
+10±0.5 ºC. Experimentally the quality of the salad with meat in
mayonnaise was characterized by measuring colour, pH and
microbiological properties. The sous vide packaging was effective in
protecting the product from physical, chemical, and microbial quality
degradation. The sous vide packaging significantly reduces microbial
growth at storage temperature of +4±0.5 ºC and +10±0.5 ºC.
Moreover, it is possible to extend the product shelf life to 52 days
even when stored at +10±0.5 ºC.
Abstract: The present study was provided to examine the
vortical structures generated by two inclined impinging jets with
experimental and numerical investigations. The jets are issuing with a
pitch angle α=40° into a confined quiescent fluid. The experimental
investigation on flow patterns was visualized by using olive particles
injected into the jets illuminated by Nd:Yag laser light to reveal the
finer details of the confined jets interaction. It was observed that two
counter-rotating vortex pairs (CVPs) were generated in the near
region. A numerical investigation was also performed. First, the
numerical results were validates against the experimental results and
then the numerical model was used to study the effect of section ratio
on the evolution of the CVPs. Our results show promising agreement
with experimental data, and indicate that our model has the potential
to produce useful and accurate data regarding the evolution of CVPs.
Abstract: Reliability Centered Maintenance(RCM) is one of
most widely used methods in the modern power system to schedule a
maintenance cycle and determine the priority of inspection. In order
to apply the RCM method to the Smart Grid, a precedence study for
the new structure of rearranged system should be performed due to
introduction of additional installation such as renewable and
sustainable energy resources, energy storage devices and advanced
metering infrastructure. This paper proposes a new method to
evaluate the priority of maintenance and inspection of the power
system facilities in the Smart Grid using the Risk Priority Number. In
order to calculate that risk index, it is required that the reliability
block diagram should be analyzed for the Smart Grid system. Finally,
the feasible technical method is discussed to estimate the risk
potential as part of the RCM procedure.
Abstract: The purpose of this article is to study the effects of
plants cover on overland flow and, therefore, its influences on the
amount of eroded and transported soil. In this investigation, all the
experiments were conducted in the LEGHYD laboratory using a
rainfall simulator and a soil tray. The experiments were conducted
using an experimental plot (soil tray) which is 2m long, 0.5 m wide
and 0.15 m deep. The soil used is an agricultural sandy soil (62,08%
coarse sand, 19,14% fine sand, 11,57% silt and 7,21% clay). Plastic
rods (4 mm in diameter) were used to simulate the plants at different
densities: 0 stem/m2 (bared soil), 126 stems/m², 203 stems/m², 461
stems/m² and 2500 stems/m²). The used rainfall intensity is 73mm/h
and the soil tray slope is fixed to 3°. The results have shown that the
overland flow velocities decreased with increasing stems density, and
the density cover has a great effect on sediment concentration.
Darcy–Weisbach and Manning friction coefficients of overland flow
increased when the stems density increased. Froude and Reynolds
numbers decreased with increasing stems density and, consequently,
the flow regime of all treatments was laminar and subcritical. From
these findings, we conclude that increasing the plants cover can
efficiently reduce soil loss and avoid denuding the roots plants.
Abstract: We propose our genuine research of geometric
moments which detects the mineral inadequacy in the frail groundnut
plant. This plant is prone to many deficiencies as a result of the
variance in the soil nutrients. By analyzing the leaves of the plant, we
detect the visual symptoms that are not recognizable to the naked eyes.
We have collected about 160 samples of leaves from the nearby fields.
The images have been taken by keeping every leaf into a black box to
avoid the external interference. For the first time, it has been possible
to provide the farmer with the stages of deficiencies. This paper has
applied the algorithms successfully to many other plants like Lady-s
finger, Green Bean, Lablab Bean, Chilli and Tomato. But we submit
the results of the groundnut predominantly. The accuracy of our
algorithm and method is almost 93%. This will again pioneer a kind of
green revolution in the field of agriculture and will be a boon to that
field.
Abstract: There are many problems associated with the World Wide
Web: getting lost in the hyperspace; the web content is still accessible only
to humans and difficulties of web administration. The solution to these
problems is the Semantic Web which is considered to be the extension
for the current web presents information in both human readable and
machine processable form. The aim of this study is to reach new
generic foundation architecture for the Semantic Web because there
is no clear architecture for it, there are four versions, but still up to
now there is no agreement for one of these versions nor is there a
clear picture for the relation between different layers and
technologies inside this architecture. This can be done depending on
the idea of previous versions as well as Gerber-s evaluation method
as a step toward an agreement for one Semantic Web architecture.
Abstract: Arc welding is an important joining process widely used in many industrial applications including production of automobile, ships structures and metal tanks. In welding process, the moving electrode causes highly non-uniform temperature distribution that leads to residual stresses and different deviations, especially buckling distortions in thin plates. In order to control the deviations and increase the quality of welded plates, a fixture can be used as a practical and low cost method with high efficiency. In this study, a coupled thermo-mechanical finite element model is coded in the software ANSYS to simulate the behavior of thin plates located by a 3-2-1 positioning system during the welding process. Computational results are compared with recent similar works to validate the finite element models. The agreement between the result of proposed model and other reported data proves that finite element modeling can accurately predict the behavior of welded thin plates.
Abstract: Experiments were carried out at the Faculty of Food
Technology of Latvia University of Agriculture (LLU). Soft cheese
Kleo produced in Latvia was packed in a biodegradable PLA without
barrierproperties and VC999 BioPack lidding film PLA, coated with
a barrier of pure silicon oxide (SiOx) and in combination with
modified atmosphere (MAP) the influence on the shelf life was
investigated and compared with some conventional (OPP, PE/PA,
PE/OPA and Multibarrier 60) polymer film impact. Modified
atmosphere consisted of carbon dioxide CO2 (E 290) 30% and
nitrogen N2 (E 941) 70%. The analyzable samples were stored at the
temperature of +4.0±0.5 °C up to 32 days- and analyzed before
packaging and in the 0, 5th, 11th, 15th, 18th, 22nd, 25th, 29th and 32nd
day of storage. The shelf life was extended along to 32 days, good
outside appearance and lactic acid aroma was observed.