Abstract: In reinforced concrete (RC) structures, beam-column connection region has a considerable effect on the behavior of structures. Using fiber reinforcement polymer (FRP) for the strengthening of connections in RC structures can be one of the solutions to retrofitting this zone which result in the enhanced behavior of structure. In this paper, these changes in behavior by using FRP for high strength concrete beam-column connection have been studied by finite element modeling. The concrete damage plasticity (CDP) model has been used to analyze the RC. The results illustrated a considerable development in load-bearing capacity but also a noticeable reduction in ductility. The study also assesses these qualities for several modes of strengthening and suggests the most effective mode of strengthening. Using FRP in flexural zone and FRP with 45-degree oriented fibers in shear zone of joint showed the most significant change in behavior.
Abstract: This research examines the performance of a hybrid passive control device for enhancing the seismic response of steel frame structures. The device design comprises a damper which employs a viscoelastic material to control both shear and axial strain. In the design, energy is dissipated through the shear strain of a two-layer system of viscoelastic pads which are located between steel plates. In addition, viscoelastic blocks have been included on either side of the main shear damper which obtains compressive strains in the viscoelastic blocks. These dampers not only dissipate energy but also increase the stiffness of the steel frame structure, and the degree to which they increase the stiffness may be controlled by the size and shape. In this research, the cyclical behavior of the damper was examined both experimentally and numerically with finite element modeling. Cyclic loading results of the finite element modeling reveal fundamental characteristics of this hybrid viscoelastic damper. The results indicate that incorporating a damper of the design can significantly improve the seismic performance of steel frame structures.
Abstract: The effect of autofrettage process in strain hardened
thick-walled pressure vessels has been investigated theoretically by
finite element modeling. Equivalent von Mises stress is used as yield
criterion to evaluate the optimum autofrettage pressure and the
optimum radius of elastic-plastic junction. It has been observed that
the optimum autofrettage pressure increases along with the working
pressure. For two different working pressures, the effect of the ratio
of outer to inner radius (b/a=k) value on the optimum autofrettage
pressure is also noticed. The Optimum autofrettage pressure solely
depends on K value rather than on the inner or outer radius.
Furthermore, percentage reduction of von Mises stresses is compared
for different working pressures and different k values. Maximum von
Mises stress developed at different autofrettage pressure is equated
for elastic perfectly plastic and elastic-plastic material with different
slope of strain hardening segment. Cylinder material having higher
slope of strain hardening segment provides better benedictions in the
autofrettage process.
Abstract: Bone material is treated as heterogeneous and hierarchical in nature therefore appropriate size of bone specimen is required to analyze its tensile properties at a particular hierarchical level. Tensile properties of cortical bone are important to investigate the effect of drug treatment, disease and aging as well as for development of computational and analytical models. In the present study tensile properties of buffalo as well as goat femoral and tibiae cortical bone are analyzed using sub-size tensile specimens. Femoral cortical bone was found to be stronger in tension as compared to the tibiae cortical bone and the tensile properties obtained using sub-size specimens show close resemblance with the tensile properties of full-size cortical specimens. A two dimensional finite element (FE) modal was also applied to simulate the tensile behavior of sub-size specimens. Good agreement between experimental and FE model was obtained for sub-size tensile specimens of cortical bone.
Abstract: Sandwich panels are widely used in the construction
industry for their ease of assembly, light weight and efficient thermal
performance. They are composed of two RC thin outer layers
separated by an insulating inner layer. In this research the inner
insulating layer is made of lightweight Autoclaved Aerated Concrete
(AAC) blocks which has good thermal insulation properties and yet
possess reasonable mechanical strength. The shear strength of the
AAC infill is relied upon to replace the traditionally used insulating
foam and to provide the shear capacity of the panel. A
comprehensive experimental program was conducted on full scale
sandwich panels subjected to bending. In this paper, detailed
numerical modeling of the tested sandwich panels is reported. Nonlinear
3-D finite element modeling of the composite action of the
sandwich panel is developed using ANSYS. Solid elements with
different crashing and cracking capabilities and different constitutive
laws were selected for the concrete and the AAC. Contact interface
elements are used in this research to adequately model the shear
transfer at the interface between the different layers. The numerical
results showed good correlation with the experimental ones
indicating the adequacy of the model in estimating the loading
capacity of panels.