Abstract: In this paper, a two-dimensional (2D) numerical
model for the tidal currents simulation in Persian Gulf is presented.
The model is based on the depth averaged equations of shallow water
which consider hydrostatic pressure distribution. The continuity
equation and two momentum equations including the effects of bed
friction, the Coriolis effects and wind stress have been solved. To
integrate the 2D equations, the Alternative Direction Implicit (ADI)
technique has been used. The base of equations discritization was
finite volume method applied on rectangular mesh. To evaluate the
model validation, a dam break case study including analytical
solution is selected and the comparison is done. After that, the
capability of the model in simulation of tidal current in a real field is
represented by modeling the current behavior in Persian Gulf. The
tidal fluctuations in Hormuz Strait have caused the tidal currents in
the area of study. Therefore, the water surface oscillations data at
Hengam Island on Hormoz Strait are used as the model input data.
The check point of the model is measured water surface elevations at
Assaluye port. The comparison between the results and the
acceptable agreement of them showed the model ability for modeling
marine hydrodynamic.
Abstract: Computer based geostatistical methods can offer effective data analysis possibilities for agricultural areas by using
vectorial data and their objective informations. These methods will help to detect the spatial changes on different locations of the large
agricultural lands, which will lead to effective fertilization for optimal yield with reduced environmental pollution. In this study, topsoil (0-20 cm) and subsoil (20-40 cm) samples were taken from a
sugar beet field by 20 x 20 m grids. Plant samples were also collected
from the same plots. Some physical and chemical analyses for these
samples were made by routine methods. According to derived variation coefficients, topsoil organic matter (OM) distribution was more than subsoil OM distribution. The highest C.V. value of
17.79% was found for topsoil OM. The data were analyzed
comparatively according to kriging methods which are also used
widely in geostatistic. Several interpolation methods (Ordinary,Simple and Universal) and semivariogram models (Spherical,
Exponential and Gaussian) were tested in order to choose the suitable
methods. Average standard deviations of values estimated by simple
kriging interpolation method were less than average standard
deviations (topsoil OM ± 0.48, N ± 0.37, subsoil OM ± 0.18) of measured values. The most suitable interpolation method was simple
kriging method and exponantial semivariogram model for topsoil,
whereas the best optimal interpolation method was simple kriging
method and spherical semivariogram model for subsoil. The results
also showed that these computer based geostatistical methods should
be tested and calibrated for different experimental conditions and semivariogram models.
Abstract: This paper presents a novel method for prediction of
the mechanical behavior of proximal femur using the general
framework of the quantitative computed tomography (QCT)-based
finite element Analysis (FEA). A systematic imaging and modeling
procedure was developed for reliable correspondence between the
QCT-based FEA and the in-vitro mechanical testing. A speciallydesigned
holding frame was used to define and maintain a unique
geometrical reference system during the analysis and testing. The
QCT images were directly converted into voxel-based 3D finite
element models for linear and nonlinear analyses. The equivalent
plastic strain and the strain energy density measures were used to
identify the critical elements and predict the failure patterns. The
samples were destructively tested using a specially-designed gripping
fixture (with five degrees of freedom) mounted within a universal
mechanical testing machine. Very good agreements were found
between the experimental and the predicted failure patterns and the
associated load levels.
Abstract: Agricultural waste is mainly composed of cellulose
and hemicelluloses which can be converted to sugars. The
inexpensive reducing sugar from durian peel was obtained by
hydrolysis with HCl concentration at 0.5-2.0% (v/v). The hydrolysis
range of time was for 15-60 min when the mixture was autoclaved at
121 °C. The result showed that acid hydrolysis efficiency (AHE)
highest to 80.99% at condition is 2.0%concentration for 15 min.
Reducing sugar highest to 56.07 g/litre at condition is 2.0%
concentration for 45min. Total sugar highest to 59.83 g/litre at
condition is 2.0%concentration for 45min, which was not significant
(p < 0.05) with condition 2.0% concentration for 30 min and 1.5 %
concentration for 45 and 60 min. The increase in concentration
increased AHE, reducing sugar and total sugar. The hydrolysis time
had no effect on AHE, reducing sugar and total sugar. The maximum
reducing sugars of each concentration were at hydrolysis time 45
min .The hydrolysated were analysis by HPLC, the results revealed
that the principle of sugar were glucose, fructose and xylose.
Abstract: In this paper we propose a robust adaptive fuzzy
controller for a class of nonlinear system with unknown dynamic.
The method is based on type-2 fuzzy logic system to approximate
unknown non-linear function. The design of the on-line adaptive
scheme of the proposed controller is based on Lyapunov technique.
Simulation results are given to illustrate the effectiveness of the
proposed approach.
Abstract: Mathematical models can be used to describe the
dynamics of the spread of infectious disease between susceptibles
and infectious populations. Dengue fever is a re-emerging disease in
the tropical and subtropical regions of the world. Its incidence has
increased fourfold since 1970 and outbreaks are now reported quite
frequently from many parts of the world. In dengue endemic regions,
more cases of dengue infection in pregnancy and infancy are being
found due to the increasing incidence. It has been reported that
dengue infection was vertically transmitted to the infants. Primary
dengue infection is associated with mild to high fever, headache,
muscle pain and skin rash. Immune response includes IgM antibodies
produced by the 5th day of symptoms and persist for 30-60 days. IgG
antibodies appear on the 14th day and persist for life. Secondary
infections often result in high fever and in many cases with
hemorrhagic events and circulatory failure. In the present paper, a
mathematical model is proposed to simulate the succession of dengue
disease transmission in pregnancy and infancy. Stability analysis of
the equilibrium points is carried out and a simulation is given for the
different sets of parameter. Moreover, the bifurcation diagrams of our
model are discussed. The controlling of this disease in infant cases is
introduced in the term of the threshold condition.
Abstract: The two agro-ecological zones became the focus of
the study because of violent nature of the incessant conflict in the
zones. The available register of farmers association was the sampling
frame work where ten percent (61) farmers per state were randomly
sampled. Data were collected and analysed using z-test. The research
findings revealed tree crops and grains production enterprises ranked
higher in Osun (rain fed zones) and Taraba states (savannah zones)
respectively. Osun state entrepreneur felt the effect of the conflict on
their enterprises more than Tarba state. The reasons adduced for
severity of the conflict on enterprises are majority (77.0%) migrated
and (75.5%) of them were not allowed to enter their farms during and
when conflict deescalated unlike situation in Taraba state. The
different in enterprises production level between the two agroecological
zone was statistically significant at p
Abstract: Paddy being cultivated since about 10,000 years B.C in Ganga Valley in India, its production reached up to 99 million tons in the year 2012. BGA are of much ecological importance for maintaining the soil fertility and reclaiming the alkalinity. In present investigation attempts were made to identify the local cyanobacterial genera from the paddy fields, BGA application for green farming enabling the paddy to utilize more amount of nitrogen released and to examine its impact along with Urea upon growth and yield responses of the Paddy crop. It was observed that combined treatment of BGA with Urea proved better response in almost all growth parameters and yield attributes except number of tillers/ Plant and grains/ panicle as compared to application of either Urea or BGA alone. The Paddy growers should be encouraged to adopt BGA along with Urea as source of Nitrogen for Paddy cultivation.
Abstract: Studies on gas solid mass transfer using Supercritical fluid CO2 (SC-CO2) in a packed bed of palm kernels was investigated at operating conditions of temperature 50 °C and 70 °C and pressures ranges from 27.6 MPa, 34.5 MPa, 41.4 MPa and 48.3 MPa. The development of mass transfer models requires knowledge of three properties: the diffusion coefficient of the solute, the viscosity and density of the Supercritical fluids (SCF). Matematical model with respect to the dimensionless number of Sherwood (Sh), Schmidt (Sc) and Reynolds (Re) was developed. It was found that the model developed was found to be in good agreement with the experimental data within the system studied.
Abstract: This paper proposed a new CAD tools for microwave amplifier design. The proposed tool is based on survey about the broadband amplifier design methods, such as the Feedback amplifiers, balanced amplifiers and Compensated Matching Network The proposed tool is developed for broadband amplifier using a compensated matching network "unconditional stability amplifier". The developed program is based on analytical procedures with ability of smith chart explanation. The C# software is used for the proposed tools implementation. The program is applied on broadband amplifier as an example for testing. The designed amplifier is considered as a broadband amplifier at the range 300-700 MHz. The results are highly agreement with the expected results. Finally, these methods can be extended for wide band amplifier design.
Abstract: The present research focus on the processing of mullite-based ceramics from oil refinery industrial wastes and byproducts of agricultural industry and on the investigating of silane modified surface of ceramics. Two waste products were used as initial material – waste aluminum oxide and waste rice husk. The burning - out additives used were waste rise husk. It is known that the oxide ceramics surface is hydrophilic due to the presence of – OH groups in it. The nature of ceramic surface regarding permeation of water and hydrocarbons can be changed by further treatment with silanes. The samples were studied mainly by X-ray analysis, FT-IR absorbance measurements and microscopic analysis. The X-ray analyses showed the phase composition depends on the firing temperature and on the purity of the starting alumina. Two kind of silanes were used for the transformation of surface from hydrophilic to hydrophobic – trimethoxymethylsilane (TMMS) and trimethylclorsilane (TMCS).
Abstract: An experimental study is presented on the effect of
Conservation Agriculture (CA) compared to Conventional
Agriculture (ConvA) upon Maize Yield based on split-plot model.
Two factors have been considered: A Factor-Fertilization with two
variants: A1- N40P40 kg/ha and A2- N90P70 kg/ha; B Factor- Crop
protection with 4 variants : B1- 4 treatments, B2-3 treatments, B3- 2
treatments and B4- 1 treatment. In comparison with conventional
agriculture, CA determined lower maize yields. Fertilization is the
key factor determining a yield gain of 973.58 kg/ha in ConvA and
1,123.33 kg/ha in CA. A reduced number of treatments determined a
yield decline. The A-B interaction had a positive effect on maize
yield when a larger amount of fertilizer and 4 or 3 treatments were
applied in ConvA and a benefic in CA for highest fertilization level
and 2 treatments. The B2A2 ConvA variant was the most efficient
leading to 302.67 kg/ha gain while B3A2 CA variant brought 181.33
kg production gain.
Abstract: Gaharu that produced by Aquilaria spp. is classified as
one of the most valuable forest products traded internationally as it is
very resinous, fragrant and highly valuable heartwood. Gaharu has
been widely used in aromatheraphy, medicine, perfume and religious
practices. This work aimed to determine the factors affecting solid
liquid extraction of gaharu oil using hexane as solvent under
experimental condition. The kinetics of extraction was assumed and
verified based on a second-order mechanism. The effect of three
main factors, which were temperature, reaction time and solvent to
solid ratio were investigated to achieve maximum oil yield. The
optimum condition were found at temperature 65°C, 9 hours reaction
time and solvent to solid ratio of 12:1 with 14.5% oil yield. The
kinetics experimental data agrees and well fitted with the second
order extraction model. The initial extraction rate (h) was 0.0115
gmL-1min-1; the extraction capacity (Cs) was 1.282gmL-1; the second
order extraction constant (k) was 0.007 mLg-1min-1 and coefficient of
determination, R2 was 0.945.
Abstract: The use of sewage sludge and effluents from
wastewater treatment plants for irrigation of agricultural lands is on
the rise particularly in peri-urban areas of developing countries.
The reuse of nutrients and organic matter in treated wastewater
and sewage sludge via land application is a desirable goal. However,
trace or heavy metals present in sludge pose the risk of human or
phytotoxicity from land application. Long-term use of sewage
sludge, heavy metals can accumulate to phytotoxic levels and results
in reduced plants growth and/or enhanced metal concentrations in
plants, which consumed by animals then enter the food chain. In this
research, the amount of heavy metals was measured in plants
irrigated with wastewater and sludge application. For this purpose,
three pilots were made in a Shush treatment plant in south of Tehran.
Three plants species, spinach, lettuce and radish were selected and
planted in the pilots.First pilot was irrigated just with wastewater of
treatment plant and second pilot was irrigated with wastewater and
sludge application .Third pilot was irrigated with simulated heavy
metals solution equal 50 years of irrigation. The results indicate that
the average of amount of heavy metals Pb, Cd in three plant species
in first pilot were lower than permissible limits .In second pilot,
Cadmium accumulations are high in three species plants and more
than the standard limits. Concentration of Cd , Pb have exceed their
permitted limits in plants in third pilot . It was concluded that the use
of wastewater and sludge application in agricultural lands enriched
soils with heavy metals to concentrations that may pose potential
environmental and health risks in the long-term.
Abstract: Lightweight ceramic materials in the form of bricks
and blocks are widely used in modern construction. They may be
obtained by adding of rice husk, rye straw, etc, as porous forming
materials. Rice husk is a major by-product of the rice milling
industry. Its utilization as a valuable product has always been a
problem. Various technologies for utilization of rice husk through
biological and thermochemical conversion are being developed.
The purpose of this work is to develop lightweight ceramic
materials with clay matrix and filler of rice husk and examine their
main physicomechanical properties. The results obtained allow to
suppose that the materials synthesized on the basis of waste materials
can be used as lightweight materials for construction purpose.
Abstract: The environmental performance of rapeseed oil (RO)
and rapeseed methyl ester(RME) from winter rape as fuels produced
in Romanian agroclimate is analyzed in this paper. The proposed
methodology is life cycle assessment (LCA) and takes into
consideration the influence of grain production and agroclimatic
conditions. This study shows favorable results first for RO and then
for RME. When compared to diesel fuel, both studied biofuels show
better results in the following impact categories: Abiotic depletion
potential (ADP), Ozone layer depletion (ODP) and Photochemical
ozone creation potential (POCP).Furthermore, the environmental
performance of the two biofuels studied can be improved by
changing the type of fertilizer used and also by using biofuels instead
of diesel in the field works.
Abstract: This paper presents a computational study of the separated flow in a planer asymmetric diffuser. The steady RANS equations for turbulent incompressible fluid flow and six turbulence closures are used in the present study. The commercial software code, FLUENT 6.3.26, was used for solving the set of governing equations using various turbulence models. Five of the used turbulence models are available directly in the code while the v2-f turbulence model was implemented via User Defined Scalars (UDS) and User Defined Functions (UDF). A series of computational analysis is performed to assess the performance of turbulence models at different grid density. The results show that the standard k-ω, SST k-ω and v2-f models clearly performed better than other models when an adverse pressure gradient was present. The RSM model shows an acceptable agreement with the velocity and turbulent kinetic energy profiles but it failed to predict the location of separation and attachment points. The standard k-ε and the low-Re k- ε delivered very poor results.
Abstract: The scroll pump belongs to the category of positive
displacement pump can be used for continuous pumping of gases at
low pressure apart from general vacuum application. The shape of
volume occupied by the gas moves and deforms continuously as the
spiral orbits. To capture flow features in such domain where mesh
deformation varies with time in a complicated manner, mesh less
solver was found to be very useful. Least Squares Kinetic Upwind
Method (LSKUM) is a kinetic theory based mesh free Euler solver
working on arbitrary distribution of points. Here upwind is enforced
in molecular level based on kinetic flux vector splitting scheme
(KFVS). In the present study we extended the LSKUM to moving
node viscous flow application. This new code LSKUM-NS-MN for
moving node viscous flow is validated for standard airfoil pitching
test case. Simulation performed for flow through scroll pump using
LSKUM-NS-MN code agrees well with the experimental pumping
speed data.
Abstract: Plant tissue culture is an important in vitro technology applied for agricultural and industrial production. A sterile condition of culture medium is one of the main aspects. The alternative technique for medium sterilization to replace autoclaving was carried out. For sterilization of plant tissue culture medium without autoclaving, ten commercial pure essential oils and 5 disinfectants were tested. Each essential oil or disinfectant was added to a 20-mL Murashige and Skoog (MS) medium before medium was solidified in a 120-mL container, kept for 2 weeks before evaluating sterile conditions. Treated media, supplemented with essential oils or disinfectants, were compared to control medium, autoclaved at 121 degree Celsius for 15 min. Sterile conditions of MS medium were found 100% from betel oil or clove oil (18 mL/20 mL medium), cinnamon oil (36 mL/20 mL medium), lavender oil or holy basil oil (108 mL/20 mL medium), and lemon oil or tea tree oil or turmeric oil (252 mL/20 mL medium), compared to 100% sterile condition from autoclaved medium. For disinfectants, 2% iodine + 2.4% potassium iodide, 2% merbromine solution, 10% povidone-iodine, 6% sodium hypochlorite or 0.1% thimerosal at 36 mL/20 mL medium provided 100% sterile conditions. Furthermore, growth of new shoots from chrysanthemum node explants on treated media (fresh weight, shoot length, root length and number of node) were also reported and discussed in the comparison of those on autoclaved medium.
Abstract: Due to the growth of the urban area towards lands
contaminated with ancient tails, in this work we evaluated if the
leaching with calcium thiosulfate (CaS2O3) for the recovery of silver,
gold and mercury from this soil, also dissolves arsenic, cadmium and
lead; for this, we determined their quantity per each fraction of size
of particle of the soil before and after the dissolution. Half of the soil
samples were leached in the plant Beneficiadora de Jales del Centro,
S. A. de C.V. and the rest of them remained in the laboratory. The
ICP-OES technique was used to determine the amounts of arsenic,
cadmium and lead, in the samples of both lots. The soil samples were
collected in a neighboring area at El Lampotal, Vetagrande,
Zacatecas, México, with an extension of 600 m2 at 22º52' 37.69'' N,
102º25' 11.73'' W. The amount of arsenic, cadmium and lead found
in nonleached soil and for a particle size of 47 μm was 203.72±3.73,
33.63±1.31 and 3480.99±20.4 mg/kg respectively.