Abstract: Low carbon deep drawing steel DC 01 according to EN 10130-91 was nitrooxidized in dissociated ammonia at 580°C/45 min and consequently oxidised at 380°C/5 min in vapour of distilled water. Material after nitrooxidation had 54 % increase of yield point, 34 % increase of strength and 10-times increased resistance to atmospheric corrosion in comparison to the material before nitrooxidation. The microstructure of treated material consisted of thin ε-phase layer connected to layer containing precipitated massive needle shaped Fe4N - γ' nitrides. This layer passed to a diffusion layer consisting of fine irregular shaped Fe16N2 - α'' nitrides regularly dispersed in ferritic matrix. Fatigue properties were examined under bending load with frequency of 20 kHz and sinusoidal symmetric cycle. The results confirmed positive influence of nitrooxidation on fatigue properties as fatigue limit of treated material was double in comparison to untreated material.
Abstract: This paper presents an intelligent speed control
system based on fuzzy logic for a voltage source PWM inverter-fed
indirect vector controlled induction motor drive. Traditional indirect
vector control system of induction motor introduces conventional PI
regulator in outer speed loop; it is proved that the low precision of the
speed regulator debases the performance of the whole system. To
overcome this problem, replacement of PI controller by an intelligent
controller based on fuzzy set theory is proposed. The performance of
the intelligent controller has been investigated through digital
simulation using MATLAB-SIMULINK package for different
operating conditions such as sudden change in reference speed and
load torque. The simulation results demonstrate that the performance
of the proposed controller is better than that of the conventional PI
controller.
Abstract: Group contribution based models are widely used in
industrial applications for its convenience and flexibility. Although a
number of group contribution models have been proposed, there were
certain limitations inherent to those models. Models based on group
contribution excess Gibbs free energy are limited to low pressures and
models based on equation of state (EOS) cannot properly describe
highly nonideal mixtures including acids without introducing
additional modification such as chemical theory. In the present study
new a new approach derived from quantum chemistry have been used
to calculate necessary EOS group interaction parameters. The
COSMO-RS method, based on quantum mechanics, provides a
reliable tool for fluid phase thermodynamics. Benefits of the group
contribution EOS are the consistent extension to hydrogen-bonded
mixtures and the capability to predict polymer-solvent equilibria up to
high pressures. The authors are confident that with a sufficient
parameter matrix the performance of the lattice EOS can be improved
significantly.
Abstract: A considerable progress has been achieved in transient
stability analysis (TSA) with various FACTS controllers. But, all
these controllers are associated with single transmission line. This
paper is intended to discuss a new approach i.e. a multi-line FACTS
controller which is interline power flow controller (IPFC) for TSA of
a multi-machine power system network. A mathematical model of
IPFC, termed as power injection model (PIM) presented and this
model is incorporated in Newton-Raphson (NR) power flow
algorithm. Then, the reduced admittance matrix of a multi-machine
power system network for a three phase fault without and with IPFC
is obtained which is required to draw the machine swing curves. A
general approach based on L-index has also been discussed to find
the best location of IPFC to reduce the proximity to instability of a
power system. Numerical results are carried out on two test systems
namely, 6-bus and 11-bus systems. A program in MATLAB has
been written to plot the variation of generator rotor angle and speed
difference curves without and with IPFC for TSA and also a simple
approach has been presented to evaluate critical clearing time for test
systems. The results obtained without and with IPFC are compared
and discussed.
Abstract: This paper proposes an auto-classification algorithm
of Web pages using Data mining techniques. We consider the
problem of discovering association rules between terms in a set of
Web pages belonging to a category in a search engine database, and
present an auto-classification algorithm for solving this problem that
are fundamentally based on Apriori algorithm. The proposed
technique has two phases. The first phase is a training phase where
human experts determines the categories of different Web pages, and
the supervised Data mining algorithm will combine these categories
with appropriate weighted index terms according to the highest
supported rules among the most frequent words. The second phase is
the categorization phase where a web crawler will crawl through the
World Wide Web to build a database categorized according to the
result of the data mining approach. This database contains URLs and
their categories.
Abstract: A new interface circuit for capacitive sensor is
presented. This paper presents the design and simulation of soil
moisture capacitive sensor interface circuit based on phase
differential technique. The circuit has been designed and fabricated
using MIMOS- 0.35"m CMOS technology. Simulation and test
results show linear characteristic from 36 – 52 degree phase
difference, representing 0 – 100% in soil moisture level. Test result
shows the circuit has sensitivity of 0.79mV/0.10 phase difference,
translating into resolution of 10% soil moisture level.
Abstract: This paper presents a pulse doubling technique in a 12-pulse ac-dc converter which supplies direct torque controlled motor drives (DTCIMD-s) in order to have better power quality conditions at the point of common coupling. The proposed technique increases the number of rectification pulses without significant changes in the installations and yields in harmonic reduction in both ac and dc sides. The 12-pulse rectified output voltage is accomplished via two paralleled six-pulse ac-dc converters each of them consisting of three-phase diode bridge rectifier. An autotransformer is designed to supply the rectifiers. The design procedure of magnetics is in a way such that makes it suitable for retrofit applications where a six-pulse diode bridge rectifier is being utilized. Independent operation of paralleled diode-bridge rectifiers, i.e. dc-ripple re-injection methodology, requires a Zero Sequence Blocking Transformer (ZSBT). Finally, a tapped interphase reactor is connected at the output of ZSBT to double the pulse numbers of output voltage up to 24 pulses. The aforementioned structure improves power quality criteria at ac mains and makes them consistent with the IEEE-519 standard requirements for varying loads. Furthermore, near unity power factor is obtained for a wide range of DTCIMD operation. A comparison is made between 6- pulse, 12-pulse, and proposed converters from view point of power quality indices. Results show that input current total harmonic distortion (THD) is less than 5% for the proposed topology at various loads.
Abstract: An important goal of parboiling is a decrease of rice broken percentage and at the beginning Selected paddy of variety of rice Tarom and soaked at three different temperatures 45 Cº, 65 Cº and 80 Cº orderly for 5 hours, 4 hours and 1.5 hours to moisture of 40 % and then in steaming stage to operate these action two steaming methods are selected steaming under pressure condition and steaming in atmosphere pressure and In the first method after exerting air, the steam pressure is increase to 1 Kg/Cm2 which is done in two different duration times of 2.5 and 5 minutes and in second method used of three times of 5,10 and 15 minutes and dry to 8% moisture and decreases of rice broken percentage at best condition in variety of Tarom of 37.2 % to 7.3 % and increases yield percentage at best condition in variety of Tarom of 69.4 % to 75.93 % and bran percentage decreased in variety of Tarom of 9.53 % to 2.2-3.2 % and this issue cause increases yield percentage in rice and use of This method is very significant for our country because broken percentage of rice in our country is 23-33 %.
Abstract: In this study acoustic emission (AE) signals obtained during deformation and fracture of two types of ferrite-martensite dual phase steels (DPS) specimens have been analyzed in frequency domain. For this reason two low carbon steels with various amounts of carbon were chosen, and intercritically heat treated. In the introduced method, identifying the mechanisms of failure in the various phases of DPS is done. For this aim, AE monitoring has been used during tensile test of several DPS with various volume fraction of the martensite (VM) and attempted to relate the AE signals and failure mechanisms in these steels. Different signals, which referred to 2-3 micro-mechanisms of failure due to amount of carbon and also VM have been seen. By Fast Fourier Transformation (FFT) of signals in distinct locations, an excellent relationship between peak frequencies in these areas and micro-mechanisms of failure were seen. The results were verified by microscopic observations (SEM).
Abstract: A novel three-phase active power filter (APF) circuit with photovoltaic (PV) system to improve the quality of service and to reduce the capacity of energy storage capacitor is presented. The energy balance concept and sampling technique were used to simplify the calculation algorithm for the required utility source current and to control the voltage of the energy storage capacitor. The feasibility was verified by using the Pspice simulations and experiments. When the APF mode was used during non-operational period, not only the utilization rate, power factor and power quality could be improved, but also the capacity of energy storage capacitor could sparing. As the results, the advantages of the APF circuit are simplicity of control circuits, low cost, and good transient response.
Abstract: The fabrication of porous NiTi shape memory alloys (SMAs) from elemental powder compacts was conducted by selfpropagating high temperature synthesis (SHS). Effects of the preheating temperature and the chamber pressure on the combustion characteristics as well as the final morphology and the composition of products were studied. The samples with porosity between 56.4 and 59.0% under preheating temperature in the range of 200-300°C and Ar-gas chamber pressure of 138 and 201 kPa were obtained. The pore structures were found to be dissimilar only in the samples processed with different preheating temperature. The major phase in the porous product is NiTi with small amounts of secondary phases, NiTi2 and Ni4Ti3. The preheating temperature and the chamber pressure have very little effect on the phase constituent. While the combustion temperature of the sample was notably increased by increasing the preheating temperature, they were slightly changed by varying the chamber pressure.
Abstract: In this study, we illustrated the performance and
microbial community of single- and two-phase systems anaerobically
co-digesting cassava pulp and pig manure. The results showed that
the volatile solid reduction and biogas productivity of two-phase
CSTR were 66 ± 4% and 2000 ± 210 ml l-1 d-1, while those of singlephase
CSTR were 59 ± 1% and 1670 ± 60 ml l-1 d-1, respectively. Codigestion
in two-phase CSTR gave higher 12% solid degradation and
25% methane production than single-phase CSTR. Phylogenetic
analysis of 16S rDNA clone library revealed that the Bacteroidetes
were the most abundant group, followed by the Clostridia in singlephase
CSTR. In hydrolysis/acidification reactor of two-phase system,
the bacteria within the phylum Firmicutes, especially Clostridium,
Eubacteriaceae and Lactobacillus were the dominant phylogenetic
groups. Among the Archaea, Methanosaeta sp. was the exclusive
predominant in both digesters while the relative abundance of
Methanosaeta sp. and Methanospirillum hungatei differed between
the two systems.
Abstract: The need for reputation assessment is particularly strong in peer-to-peer (P2P) systems because the peers' personal site autonomy is amplified by the inherent technological decentralization of the environment. However, the decentralization notion makes the problem of designing a peer-to-peer based reputation assessment substantially harder in P2P networks than in centralized settings.Existing reputation systems tackle the reputation assessment process in an ad-hoc manner. There is no systematic and coherent way to derive measures and analyze the current reputation systems. In this paper, we propose a reputation assessment process and use it to classify the existing reputation systems. Simulation experiments are conducted and focused on the different methods in selecting the recommendation sources and retrieving the recommendations. These two phases can contribute significantly to the overall performance due to communication cost and coverage.
Abstract: This study reports the preparation of soft magnetic
ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213
mm and, with a thickness of approximately 22 μm ± 2 μm. The microstructure and magnetic properties of the ribbons were
characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material
properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic
measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide
ribbon, the magnetic responses are not uniformly distributed. To
understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a
ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.
Abstract: In our recent study, we have used ZnO nanoparticles assisted with UV light irradiation to investigate the photocatalytic degradation of Phenol Red (PR). The ZnO photocatalyst was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), specific surface area analysis (BET) and UVvisible spectroscopy. X-ray diffractometry result for the ZnO nanoparticles exhibit normal crystalline phase features. All observed peaks can be indexed to the pure hexagonal wurtzite crystal structures, with the space group of P63mc. There are no other impurities in the diffraction peak. In addition, TEM measurement shows that most of the nanoparticles are rod-like and spherical in shape and fairly monodispersed. A significant degradation of the PR was observed when the catalyst was added into the solution even without the UV light exposure. In addition, the photodegradation increases with the photocatalyst loading. The surface area of the ZnO nanomaterials from the BET measurement was 11.9 m2/g. Besides the photocatalyst loading, the effect of some parameters on the photodegradation efficiency such as initial PR concentration and pH were also studied.
Abstract: Due to heightened concerns over environmental and economic issues the growing important of air pollution, and the importance of conserving fossil fuel resources in the world, the automotive industry is now forced to produce more fuel efficient, low emission vehicles and new drive system technologies. One of the most promising technologies to receive attention is the hybrid electric vehicle (HEV), which consists of two or more energy sources that supply energy to electric traction motors that in turn drive the wheels. This paper presents the various structures of HEV systems, the basic theoretical knowledge for describing their operation and the general behaviour of the HEV in acceleration, cruise and deceleration phases. The conventional design and sizing of a series HEV is studied. A conventional bus and its series configuration are defined and evaluated using the ADVISOR. In this section the simulation of a standard driving cycle and prediction of its fuel consumption and emissions of the HEV are discussed. Finally the bus performance is investigated to establish whether it can satisfy the performance, fuel consumption and emissions requested. The validity of the simulation has been established by the close conformity between the fuel consumption of the conventional bus reported by the manufacturer to what has achieved from the simulation.
Abstract: In literature, there are metrics for identifying the
quality of reusable components but the framework that makes use of
these metrics to precisely predict reusability of software components
is still need to be worked out. These reusability metrics if identified
in the design phase or even in the coding phase can help us to reduce
the rework by improving quality of reuse of the software component
and hence improve the productivity due to probabilistic increase in
the reuse level. As CK metric suit is most widely used metrics for
extraction of structural features of an object oriented (OO) software;
So, in this study, tuned CK metric suit i.e. WMC, DIT, NOC, CBO
and LCOM, is used to obtain the structural analysis of OO-based
software components. An algorithm has been proposed in which the
inputs can be given to K-Means Clustering system in form of
tuned values of the OO software component and decision tree is
formed for the 10-fold cross validation of data to evaluate the in
terms of linguistic reusability value of the component. The developed
reusability model has produced high precision results as desired.
Abstract: This paper presents a procedure of forming the
mathematical model of radial electric power systems for simulation
of both transient and steady-state conditions. The research idea has
been based on nodal voltages technique and on differentiation of
Kirchhoff's current law (KCL) applied to each non-reference node of
the radial system, the result of which the nodal voltages has been
calculated by solving a system of algebraic equations. Currents of the
electric power system components have been determined by solving
their respective differential equations. Transforming the three-phase
coordinate system into Cartesian coordinate system in the model
decreased the overall number of equations by one third. The use of
Cartesian coordinate system does not ignore the DC component
during transient conditions, but restricts the model's implementation
for symmetrical modes of operation only. An example of the input
data for a four-bus radial electric power system has been calculated.
Abstract: In metal cutting industries, mathematical/statistical
models are typically used to predict tool replacement time. These
off-line methods usually result in less than optimum replacement
time thereby either wasting resources or causing quality problems.
The few online real-time methods proposed use indirect measurement
techniques and are prone to similar errors. Our idea is based on
identifying the optimal replacement time using an electronic nose to
detect the airborne compounds released when the tool wear reaches
to a chemical substrate doped into tool material during the
fabrication. The study investigates the feasibility of the idea, possible
doping materials and methods along with data stream mining
techniques for detection and monitoring different phases of tool
wear.
Abstract: A new target detection technique is presented in this
paper for the identification of small boats in coastal surveillance. The
proposed technique employs an adaptive progressive thresholding (APT) scheme to first process the given input scene to separate any
objects present in the scene from the background. The preprocessing
step results in an image having only the foreground objects, such as
boats, trees and other cluttered regions, and hence reduces the search
region for the correlation step significantly. The processed image is then fed to the shifted phase-encoded fringe-adjusted joint transform
correlator (SPFJTC) technique which produces single and delta-like
correlation peak for a potential target present in the input scene. A
post-processing step involves using a peak-to-clutter ratio (PCR) to determine whether the boat in the input scene is authorized or unauthorized. Simulation results are presented to show that the
proposed technique can successfully determine the presence of an authorized boat and identify any intruding boat present in the given input scene.