Abstract: Biochemical and molecular analysis of some
antioxidant enzyme genes revealed different level of gene expression
on oilseed (Brassica napus). For molecular and biochemical
analysis, leaf tissues were harvested from plants at eight different
developmental stages, from young to senescence. The levels of total
protein and chlorophyll were increased during maturity stages of
plant, while these were decreased during the last stages of plant
growth. Structural analysis (nucleotide and deduced amino acid
sequence, and phylogenic tree) of a complementary DNA revealed a
high level of similarity for a family of Catalase genes. The
expression of the gene encoded by different Catalase isoforms was
assessed during different plant growth phase. No significant
difference between samples was observed, when Catalase activity
was statistically analyzed at different developmental stages. EST
analysis exhibited different transcripts levels for a number of other
relevant antioxidant genes (different isoforms of SOD and
glutathione). The high level of transcription of these genes at
senescence stages was indicated that these genes are senescenceinduced
genes.
Abstract: Porcelain specimens were fired at 6C/min to 1250C (dwell time 0.5-3h) and cooled at 6C/min to room temperature. Additionally, three different slower firing/cooling cycles were tried. Sintering profile and effects on MOR, crystalline phase content and morphology were investigated using dilatometry, 4-point bending strength, XRD and FEG-SEM respectively. Industrial-sized specimens prepared using the promising cycle were tested basing on the ANSI standards. Increasing dwell time from 1h to 3h at peak temperature of 1250C resulted in neither a significant effect on the quartz and mullite content nor MOR. Reducing the firing/cooling rate to below 6C/min, for peak temperature of 1250C (dwell time of 1h) does not result in improvement of strength of porcelain. The industrial sized specimen exhibited flashover voltages of 20.3kV (dry) and 9.3kV (wet) respectively, transverse strength of 12.5kN and bulk density of 2.27g/cm3, which are satisfactory. There was however dye penetration during porosity test. KeywordsDwell time, Microstructure, Porcelain, Strength.
Abstract: The source voltage of high-power fuel cell shows strong load dependence at comparatively low voltage levels. In order to provide the voltage of 750V on the DC-link for feeding electrical energy into the mains via a three phase inverter a step-up converter with a large step-up ratio is required. The output voltage of this DC/DC-converter must be stabile during variations of the load current and the voltage of the fuel cell. This paper presents the methods and results of the calculation of the efficiency and the expense for the realization for the circuits of the DC/DC-converter that meet these requirements.
Abstract: The present investigation was undertaken to explore the biogas potentiality of Jatropha (Jatropha curcas, Euphorbiaceae) Fruit Coat (JFC) alone and in combination with cattle dung (CD) in various proportions at 15 per cent total solids by batch phase anaerobic digestion for a period of ten weeks HRT (Hydraulic Retention Time) under a temperature of 35°C+1°C. The maximum biogas production was noticed in Cattle dung and Jatropha Fruit Coat in 2:1 ratio with 403.84 L/kg dry matter followed by 3:1,1:2, 1:1 and 1:3 having 329.66, 219.77, 217.79, 203.64 L /kg dm respectively as compared to 178.49 L/kg dm in CD alone. The JFC alone found to produce 91 per cent of total biogas that obtained from Cattle dung. The per cent methane content of the biogas in all the treatments was found on par with Cattle dung.
Abstract: Numerical calculations of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann method at Reynolds number 150. The effects of upstream locations, downstream locations and blockage are investigated systematically. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The results had shown that the upstream, downstream and height of the computational domain are at least 7.5, 37.5 and 12 diameters of the cylinder, respectively.
Abstract: An investigation of the process of deformation hardening and evolution of deformation defect medium in dispersion-hardened materials with face centered cubic matrices and nanoparticles was done. Mathematical model including balance equation for the deformation defects was used.
Abstract: Low oxygen content vanadium powder was
prepared by hydrogenation dehydrogenization (HDH). The
effect of purification treatment on hydrogen absorption kinetics
of dendritic vanadium was tested, and the effects of milling
technique on powder yield and grain size were studied. The
crystal phase, oxygen and nitrgen content, and grain size of
prepared powder were characterized and analyzed by X-ray
diffraction (XRD), oxygen and nitrogen analyzer and grain size
analyzer. The results show that the alkaline cleaning can
improve the hydrogen absorption of vanadium. The yield of
vanadium hydride powder can reach as high as 90% by 4h
ball-milling, The resultant product also have an oxygen content
less than 600μg/g, and the grain size is smaller than 37μm.
Meanwhile, the XRD results show that the phase of hydride
vanadium powder is mainly VH0.81. After a hydrogen
desorption treatment in vacuum at 700Ôäâ, the phase of the
powder converts into V and a little of V2H.
Abstract: Combustion, emission and performance
characterization of a single cylinder diesel engine using methanol
diesel blends was carried out. The blends were 5% (v/v) methanol in
diesel (MD05) and 10% (v/v) methanol in diesel (MD10). The
problem of solubility of methanol and diesel was addressed by an
agitator placed inside the fuel tank to prevent phase separation. The
results indicated that total combustion duration was reduced by15.8%
for MD05 and 31.27% for MD10compared to the baseline data.
Ignition delay was increased with increasing methanol volume
fraction in the test fuel. Total cyclic heat release was reduced by
1.5% for MD05 and 6.7% for MD10 as compared to diesel baseline.
Emissions of carbon monoxide, hydrocarbons along with smoke were
reduced and that of nitrogen oxides were increased with rising
methanol contents in the test fuel. Full load brake thermal efficiency
was marginally reduced with increased methanol composition in the
blend.
Abstract: Natural outdoor scene classification is active and
promising research area around the globe. In this study, the
classification is carried out in two phases. In the first phase, the
features are extracted from the images by wavelet decomposition
method and stored in a database as feature vectors. In the second
phase, the neural classifiers such as back-propagation neural network
(BPNN) and resilient back-propagation neural network (RPNN) are
employed for the classification of scenes. Four hundred color images
are considered from MIT database of two classes as forest and street.
A comparative study has been carried out on the performance of the
two neural classifiers BPNN and RPNN on the increasing number of
test samples. RPNN showed better classification results compared to
BPNN on the large test samples.
Abstract: This research elaborates decision models for product
innovation in the early phases, focusing on one of the most widely
implemented method in marketing research: conjoint analysis and the
related conjoint-based models with special focus on heuristics
programming techniques for the development of optimal product
innovation. The concept, potential, requirements and limitations of
conjoint analysis and its conjoint-based heuristics successors are
analysed and the development of conceptual framework of Genetic
Algorithm (GA) as one of the most widely implemented heuristic
methods for developing product innovations are discussed.
Abstract: In this article the investigation about installation heat
recovery steam generation (HRSG) on the exhaust of turbo generators of phases 2&3 at South Pars Gas Complex is presented.
The temperature of exhaust gas is approximately 665 degree centigrade, Installation of heat recovery boiler was simulated in
ThermoFlow 17.0.2 software, based on test operation data and the
equipments site operation conditions in Pars exclusive economical energy area, the affect of installation HRSG package on the available
gas turbine and its operation parameters, ambient temperature, the
exhaust temperatures steam flow rate were investigated. Base on the results recommended HRSG package should have the capacity for 98
ton per hour high pressure steam generation this refinery, by use of
exhaust of three gas turbines for each package in operation condition of each refinery at 30 degree centigrade. Besides saving energy this
project will be an Environment-Friendly project. The Payback Period
is estimated approximately 1.8 year, with considering Clean Development Mechanism.
Abstract: Organ motion, especially respiratory motion, is a technical challenge to radiation therapy planning and dosimetry. This motion induces displacements and deformation of the organ tissues within the irradiated region which need to be taken into account when simulating dose distribution during treatment. Finite element modeling (FEM) can provide a great insight into the mechanical behavior of the organs, since they are based on the biomechanical material properties, complex geometry of organs, and anatomical boundary conditions. In this paper we present an original approach that offers the possibility to combine image-based biomechanical models with particle transport simulations. We propose a new method to map material density information issued from CT images to deformable tetrahedral meshes. Based on the principle of mass conservation our method can correlate density variation of organ tissues with geometrical deformations during the different phases of the respiratory cycle. The first results are particularly encouraging, as local error quantification of density mapping on organ geometry and density variation with organ motion are performed to evaluate and validate our approach.
Abstract: This paper presents a systematic approach for designing Unified Power Flow Controller (UPFC) based supplementary damping controllers for damping low frequency oscillations in a single-machine infinite-bus power system. Detailed investigations have been carried out considering the four alternatives UPFC based damping controller namely modulating index of series inverter (mB), modulating index of shunt inverter (mE), phase angle of series inverter (δB ) and phase angle of the shunt inverter (δE ). The design problem of the proposed controllers is formulated as an optimization problem and Real- Coded Genetic Algorithm (RCGA) is employed to optimize damping controller parameters. Simulation results are presented and compared with a conventional method of tuning the damping controller parameters to show the effectiveness and robustness of the proposed design approach.
Abstract: This paper presents an approach for the design of
fuzzy logic power system stabilizers using genetic algorithms. In the
proposed fuzzy expert system, speed deviation and its derivative
have been selected as fuzzy inputs. In this approach the parameters of
the fuzzy logic controllers have been tuned using genetic algorithm.
Incorporation of GA in the design of fuzzy logic power system
stabilizer will add an intelligent dimension to the stabilizer and
significantly reduces computational time in the design process. It is
shown in this paper that the system dynamic performance can be
improved significantly by incorporating a genetic-based searching
mechanism. To demonstrate the robustness of the genetic based
fuzzy logic power system stabilizer (GFLPSS), simulation studies on
multimachine system subjected to small perturbation and three-phase
fault have been carried out. Simulation results show the superiority
and robustness of GA based power system stabilizer as compare to
conventionally tuned controller to enhance system dynamic
performance over a wide range of operating conditions.
Abstract: Selected Mapping (SLM) is a PAPR reduction technique, which converts the OFDM signal into several independent signals by multiplication with the phase sequence set and transmits one of the signals with lowest PAPR. But it requires the index of the selected signal i.e. side information (SI) to be transmitted with each OFDM symbol. The PAPR reduction capability of the SLM scheme depends on the selection of phase sequence set. In this paper, we have proposed a new phase sequence set generation scheme based on M-ary chaotic sequence and a mapping scheme to map quaternary data to concentric circle constellation (CCC) is used. It is shown that this method does not require SI and provides better SER performance with good PAPR reduction capability as compared to existing SLMOFDM methods.
Abstract: In this paper the behavior of the decision feedback
equalizers (DFEs) adapted by the decision-directed or the constant
modulus blind algorithms is presented. An analysis of the error
surface of the corresponding criterion cost functions is first
developed. With the intention of avoiding the ill-convergence of the
algorithm, the paper proposes to modify the shape of the cost
function error surface by using a soft decision instead of the hard
one. This was shown to reduce the influence of false decisions and to
smooth the undesirable minima. Modified algorithms using the soft
decision during a pseudo-training phase with an automatic switch to
the properly tracking phase are then derived. Computer simulations
show that these modified algorithms present better ability to avoid
local minima than conventional ones.
Abstract: This study examines the design and construction of AC Electronics load surge protection in order to carry electric surge load arisen from faults in low voltage electricity system (single phase/220V) by using the principle of electronics load clamping voltage during induction period so that electric voltage could go through to safe load and continue to work. The qualification of the designed device could prevent both transient over voltage and voltage swell. Both will work in cooperation, resulting in the ability to improve and modify the quality of electrical power in Thailand electricity distribution system more effective than the past and help increase the lifetime of electric appliances, electric devices, and electricity protection equipments.
Abstract: This paper presents an experimental investigation using Acoustic Emission (AE) technology to monitor sand transportation in multiphase flow. The investigations were undertaken on three-phase (air-water-sand) flow in a horizontal pipe where the superficial gas velocity (VSG) had a range of between 0.2msˉ¹ to 2.0msˉ¹ and superficial liquid velocity (VSL) had a range of between 0.2msˉ¹ to 1.0msˉ¹. The experimental findings clearly show a correlation exists between AE energy levels, sand concentration, superficial gas velocity (VSG), and superficial liquid velocity (VSL).
Abstract: Boron minerals are very useful for various industrial
activities, such as glass industry and detergent industry, due to its
mechanical and chemical properties. During the production of boron
compounds, many of these are introduced into the environment in the
form of waste. Boron is also an important micro nutrient for the
plants to vegetate but if it exists in high concentrations, it could have
toxic effects. The maximum boron level in drinking water for human
health is given as 0.3 mg/L in World Health Organization (WHO)
standards. The toxic effects of boron should be noted especially for
dry regions, thus, in recent years, increasing attention has been paid
to remove the boron from waste waters. In this study, boron removal
is implemented by ion exchange process using Amberlite IRA-743
resin. Amberlite IRA-743 resin is a boron specific resin and it
belongs to the polymerizate sorbent group within the aminopolyol
functional group. Batch studies were performed to investigate the
effects of various experimental parameters, such as adsorbent dose,
initial concentration and pH, on the removal of boron. It is found
that, when the adsorbent dose increases removal of boron from the
liquid phase increases. However, an increase in the initial
concentration decreases the removal of boron. The effective pH
values for removal of boron are determined between 8.5 and 9.
Equilibrium isotherms were also analyzed by Langmuir and
Freundlich isotherm models. The Langmuir isotherm is obeyed better
than the Freundlich isotherm.
Abstract: This paper describes the design and modeling
procedure of a novel 5-phase segment type switched reluctance motor
(ST-SRM) under simultaneous two-phase (bipolar) excitation of
windings. The rotor cores of ST-SRM are embedded in an aluminum
block as well as to improve the performance characteristics. The
magnetic circuit of the produced ST-SRM is constructed so that the
magnetic flux paths are short and exclusive to each phase, thereby
minimizing the commutation switching and eddy current losses in the
laminations. The design and simulation principles presented apply
primarily to conventional SRM and ST-SRM. It is proved that the
novel 5-phase switched reluctance motor under two-phase excitation
is superior among the criteria used in comparison. The purposed
model is particularly well suited for high torque and weight
constrained applications such as automobiles, aerospace and military
applications.