Abstract: Scale Time Offset Robust Modulation (STORM) [1]–
[3] is a high bandwidth waveform design that adds time-scale
to embedded reference modulations using only time-delay [4]. In
an environment where each user has a specific delay and scale,
identification of the user with the highest signal power and that
user-s phase is facilitated by the STORM processor. Both of these
parameters are required in an efficient multiuser detection algorithm.
In this paper, the STORM modulation approach is evaluated with
a direct sequence spread quadrature phase shift keying (DS-QPSK)
system. A misconception of the STORM time scale modulation is that
a fine temporal resolution is required at the receiver. STORM will
be applied to a QPSK code division multiaccess (CDMA) system
by modifying the spreading codes. Specifically, the in-phase code
will use a typical spreading code, and the quadrature code will
use a time-delayed and time-scaled version of the in-phase code.
Subsequently, the same temporal resolution in the receiver is required
before and after the application of STORM. In this paper, the bit error
performance of STORM in a synchronous CDMA system is evaluated
and compared to theory, and the bit error performance of STORM
incorporated in a single user WCDMA downlink is presented to
demonstrate the applicability of STORM in a modern communication
system.
Abstract: The proof of concept experiments were conducted to
determine the feasibility of using small amounts of Dissolved
Sulphur (DS) from the gaseous phase to precipitate platinum ions in
chloride media. Two sets of precipitation experiments were
performed in which the source of sulphur atoms was either a
thiosulphate solution (Na2S2O3) or a sulphur dioxide gas (SO2). In
liquid-liquid (L-L) system, complete precipitation of Pt was achieved
at small dosages of Na2S2O3 (0.01 – 1.0 M) in a time interval of 3-5
minutes. On the basis of this result, gas absorption tests were carried
out mainly to achieve sulphur solubility equivalent to 0.018 M. The
idea that huge amounts of precious metals could be recovered
selectively from their dilute solutions by utilizing the waste SO2
streams at low pressure seemed attractive from the economic and
environmental point of views. Therefore, mass transfer characteristics
of SO2 gas associated with reactive absorption across the gas-liquid
(G-L) interface were evaluated under different conditions of pressure
(0.5 – 2 bar), solution temperature ranges from 20 – 50 oC and acid
strength (1 – 4 M, HCl). This paper concludes with information about
selective precipitation of Pt in the presence of cations (Fe2+, Co2+,
and Cr3+) in a CSTR and recommendation to scale up laboratory data
to industrial pilot scale operations.
Abstract: This is a study on numerical simulation of the convection-diffusion transport of a chemical species in steady flow through a small-diameter tube, which is lined with a very thin layer made up of retentive and absorptive materials. The species may be subject to a first-order kinetic reversible phase exchange with the wall material and irreversible absorption into the tube wall. Owing to the velocity shear across the tube section, the chemical species may spread out axially along the tube at a rate much larger than that given by the molecular diffusion; this process is known as dispersion. While the long-time dispersion behavior, well described by the Taylor model, has been extensively studied in the literature, the early development of the dispersion process is by contrast much less investigated. By early development, that means a span of time, after the release of the chemical into the flow, that is shorter than or comparable to the diffusion time scale across the tube section. To understand the early development of the dispersion, the governing equations along with the reactive boundary conditions are solved numerically using the Flux Corrected Transport Algorithm (FCTA). The computation has enabled us to investigate the combined effects on the early development of the dispersion coefficient due to the reversible and irreversible wall reactions. One of the results is shown that the dispersion coefficient may approach its steady-state limit in a short time under the following conditions: (i) a high value of Damkohler number (say Da ≥ 10); (ii) a small but non-zero value of absorption rate (say Γ* ≤ 0.5).
Abstract: A robust AUSM+ upwind discretisation scheme has been developed to simulate multiphase flow using consistent spatial discretisation schemes and a modified low-Mach number diffusion term. The impact of the selection of an interfacial pressure model has also been investigated. Three representative test cases have been simulated to evaluate the accuracy of the commonly-used stiffenedgas equation of state with respect to the IAPWS-IF97 equation of state for water. The algorithm demonstrates a combination of robustness and accuracy over a range of flow conditions, with the stiffened-gas equation tending to overestimate liquid temperature and density profiles.
Abstract: Dynamic models of power converters are normally
time-varying because of their switching actions. Several approaches
are applied to analyze the power converters to achieve the timeinvariant
models suitable for system analysis and design via the
classical control theory. The paper presents how to derive dynamic
models of the power system consisting of a three-phase controlled
rectifier feeding an uncontrolled buck converter by using the
combination between the well known techniques called the DQ and
the generalized state-space averaging methods. The intensive timedomain
simulations of the exact topology model are used to support
the accuracies of the reported model. The results show that the
proposed model can provide good accuracies in both transient and
steady-state responses.
Abstract: Reactive powder concretes (RPC) are characterized by
particle diameter not exceeding 600 μm and having very high
compressive and tensile strengths. This paper describes a new
generation of micro concrete, which has an initial, as well as a final,
high physicomechanical performance. To achieve this, we replaced
the Portland cement (15% by weight) by materials rich in Silica (Slag
and Dune Sand).
The results obtained from tests carried out on RPC show that
compressive and tensile strengths increase when adding the additions,
thus improving the compactness of mixtures via filler and pozzolanic
effect.
With a reduction of the aggregate phase in the RPC and the
abundance of dune sand (south Algeria) and slag (industrial byproduct
of blast furnace), the use of the RPC will allow Algeria to
fulfil economical as well as ecological requirements.
Abstract: Ultrasound is useful in demonstrating bone mineral
density of regenerating osseous tissue as well as structural alterations.
A proposed ultrasound method, which included ultrasonography and
acoustic parameters measurement, was employed to evaluate its
efficacy in monitoring the bone callus changes in a rabbit tibial
distraction osteogenesis (DO) model.
The findings demonstrated that ultrasonographic images depicted
characteristic changes of the bone callus, typical of histology findings,
during the distraction phase. Follow-up acoustic parameters
measurement of the bone callus, including speed of sound, reflection
and attenuation, showed significant linear changes over time during
the distraction phase. The acoustic parameters obtained during the
distraction phase also showed moderate to strong correlation with
consolidated bone callus density and micro-architecture measured by
micro-computed tomography at the end of the consolidation phase.
The results support the preferred use of ultrasound imaging in the
early monitoring of bone callus changes during DO treatment.
Abstract: Three dimensional simulations in tube in tube heat
exchangers are investigated numerically in this study. In these
simulations forced convective heat transfer and laminar flow of
single-phase water are considered. In order to measure heat transfer
parameters in these heat exchangers, FLUENT CFD Solver is used in
this numerical method. For the purpose of creating geometry and
exert boundary and initial conditions in the present model, finite
volume method in Computational Fluid Dynamics is used in this
study. In the present study, at each Z-location, variation of local
temperatures, heat flux and Nusselt number at the whole tube is
investigated in detail. Thereafter, averaged computational Nusselt
number in this model is calculated. In addition, conceivable pressure
drops have been obtained at each Z-location in this model. Then,
pressure drop values in the present model are explored. Finally, all
the numerical results for this kind of heat exchanger will be discussed
precisely.
Abstract: We successfully developed and tested a new
separation layer solving problems with unmanageable deposits inside the boilers of Zluticka Heating Plant. The deposits are mainly created
by glass-forming melts. We plotted straw ash compositions in K2OCaO-
SiO2 phase diagram and illustrated that they are in the area of low-melting eutectic points. To prevent the melting of ash and the
formation of deposits, we modified ash compositions by injecting additives into biomass fuel, and thus effectively suppressed deposits in a burner.
Abstract: The present paper deals with problems related to the
possibilities to use fractal systems to solve some important scientific
and practical problems connected with filtering and separation of
aqueous phases from organic ones. For this purpose a special
separator have been designed. The reactor was filled with a porous
material with fractal dimension, which is an integral part of the set
for filtration and separation of emulsions. As a model emulsion
hexadecan mixture with water in equal quantities (1:1) was used. We
examined the hydrodynamics of the separation of the emulsion at
different rates of submission of the entrance of the reactor.
Abstract: We investigated statistical performance of Bayesian inference using maximum entropy and MAP estimation for several models which approximated wave-fronts in remote sensing using SAR interferometry. Using Monte Carlo simulation for a set of wave-fronts generated by assumed true prior, we found that the method of maximum entropy realized the optimal performance around the Bayes-optimal conditions by using model of the true prior and the likelihood representing optical measurement due to the interferometer. Also, we found that the MAP estimation regarded as a deterministic limit of maximum entropy almost achieved the same performance as the Bayes-optimal solution for the set of wave-fronts. Then, we clarified that the MAP estimation perfectly carried out phase unwrapping without using prior information, and also that the MAP estimation realized accurate phase unwrapping using conjugate gradient (CG) method, if we assumed the model of the true prior appropriately.
Abstract: Numerical investigation of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann methods at different Reynolds numbers. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations, streamlines and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The Reynolds numbers affected the physical quantities.
Abstract: Unsteady natural convection and heat transfer in a square cavity partially filled with porous media using a thermal
non-equilibrium model is studied in this paper. The left vertical wall is
maintained at a constant hot temperature Th and the right vertical wall
is maintained at a constant cold temperature Tc, while the horizontal
walls are adiabatic. The governing equations are obtained by applying
the Darcy model and Boussinesq approximation. COMSOL’s finite
element method is used to solve the non-dimensional governing
equations together with specified boundary conditions. The governing
parameters of this study are the Rayleigh number (Ra = 10^5, and Ra = 10^6 ), Darcy namber (Da = 10^−2, and Da = 10^−3),
the modified thermal conductivity ratio (10^−1 ≤ γ ≤ 10^4), the inter-phase heat transfer coefficien (10^−1 ≤ H ≤ 10^3) and the
time dependent (0.001 ≤ τ ≤ 0.2). The results presented for
values of the governing parameters in terms of streamlines in both
fluid/porous-layer, isotherms of fluid in fluid/porous-layer, isotherms
of solid in porous layer, and average Nusselt number.
Abstract: In order to accelerate the similarity search in highdimensional database, we propose a new hierarchical indexing method. It is composed of offline and online phases. Our contribution concerns both phases. In the offline phase, after gathering the whole of the data in clusters and constructing a hierarchical index, the main originality of our contribution consists to develop a method to construct bounding forms of clusters to avoid overlapping. For the online phase, our idea improves considerably performances of similarity search. However, for this second phase, we have also developed an adapted search algorithm. Our method baptized NOHIS (Non-Overlapping Hierarchical Index Structure) use the Principal Direction Divisive Partitioning (PDDP) as algorithm of clustering. The principle of the PDDP is to divide data recursively into two sub-clusters; division is done by using the hyper-plane orthogonal to the principal direction derived from the covariance matrix and passing through the centroid of the cluster to divide. Data of each two sub-clusters obtained are including by a minimum bounding rectangle (MBR). The two MBRs are directed according to the principal direction. Consequently, the nonoverlapping between the two forms is assured. Experiments use databases containing image descriptors. Results show that the proposed method outperforms sequential scan and SRtree in processing k-nearest neighbors.
Abstract: A facile vapour deposition method of synthesis of vertically aligned ZnO nanowires on carbon seed layer was developed. The received samples were investigated on electronic microscope JSM-6490 LA JEOL and x-ray diffractometer X, pert MPD PRO. The photoluminescence spectra (PL) of obtained ZnO samples at a room temperature were studied using He-Cd laser (325 nm line) as excitation source.
Abstract: This paper presents a microstrip meandered open
circuited stub with bandstop characteristic. The proposed structure is
designed on a high frequency laminate with dielectric constant of 4.0
and board thickness of 0.508 millimeters. The scattering parameters
and electromagnetic field distributions at various frequencies are
investigated by modeling the structure with three dimensional
electromagnetic simulation tool. In order to describe the resonant
and bandstop characteristic of the meandered open circuited stub, a
Smith chart as well as electric field at various frequencies and phases
is illustrated accordingly. The structure can be an alternative method
in suppressing the harmonic response of a bandpass filter.
Abstract: Distributed denial-of-service (DDoS) attacks pose a
serious threat to network security. There have been a lot of
methodologies and tools devised to detect DDoS attacks and reduce
the damage they cause. Still, most of the methods cannot
simultaneously achieve (1) efficient detection with a small number of
false alarms and (2) real-time transfer of packets. Here, we introduce
a method for proactive detection of DDoS attacks, by classifying the
network status, to be utilized in the detection stage of the proposed
anti-DDoS framework. Initially, we analyse the DDoS architecture
and obtain details of its phases. Then, we investigate the procedures
of DDoS attacks and select variables based on these features. Finally,
we apply the k-nearest neighbour (k-NN) method to classify the
network status into each phase of DDoS attack. The simulation result
showed that each phase of the attack scenario is classified well and
we could detect DDoS attack in the early stage.
Abstract: Fractional Fourier Transform is a powerful tool,
which is a generalization of the classical Fourier Transform. This
paper provides a mathematical relation relating the span in Fractional
Fourier domain with the amplitude and phase functions of the signal,
which is further used to study the variation of quality factor with
different values of the transform order. It is seen that with the
increase in the number of transients in the signal, the deviation of
average Fractional Fourier span from the frequency bandwidth
increases. Also, with the increase in the transient nature of the signal,
the optimum value of transform order can be estimated based on the
quality factor variation, and this value is found to be very close to
that for which one can obtain the most compact representation. With
the entire mathematical analysis and experimentation, we consolidate
the fact that Fractional Fourier Transform gives more optimal
representations for a number of transform orders than Fourier
transform.
Abstract: Developing techniques for mobile robot navigation constitutes one of the major trends in the current
research on mobile robotics. This paper develops a local
model network (LMN) for mobile robot navigation. The
LMN represents the mobile robot by a set of locally valid
submodels that are Multi-Layer Perceptrons (MLPs).
Training these submodels employs Back Propagation (BP) algorithm. The paper proposes the fuzzy C-means (FCM) in this scheme to divide the input space to sub regions, and then a submodel (MLP) is identified to represent a particular
region. The submodels then are combined in a unified
structure. In run time phase, Radial Basis Functions (RBFs) are employed as windows for the activated submodels. This
proposed structure overcomes the problem of changing operating regions of mobile robots. Read data are used in all experiments. Results for mobile robot navigation using the
proposed LMN reflect the soundness of the proposed
scheme.
Abstract: Heavy rainfall greatly affects the aerodynamic performance of the aircraft. There are many accidents of aircraft caused by aerodynamic efficiency degradation by heavy rain. In this Paper we have studied the heavy rain effects on the aerodynamic efficiency of NACA 64-210 & NACA 0012 airfoils. For our analysis, CFD method and preprocessing grid generator are used as our main analytical tools, and the simulation of rain is accomplished via two phase flow approach-s Discrete Phase Model (DPM). Raindrops are assumed to be non-interacting, non-deforming, non-evaporating and non-spinning spheres. Both airfoil sections exhibited significant reduction in lift and increase in drag for a given lift condition in simulated rain. The most significant difference between these two airfoils was the sensitivity of the NACA 64-210 to liquid water content (LWC), while NACA 0012 performance losses in the rain environment is not a function of LWC . It is expected that the quantitative information gained in this paper will be useful to the operational airline industry and greater effort such as small scale and full scale flight tests should put in this direction to further improve aviation safety.