Abstract: The aim of this study was to select the best strains of
Saccharomyces cerevisiae able to resist lead and cadmium. Ten
strains were screened on the basis of their resistance at different
concentrations of 0, 2, 4, 8, 12, 16, 20 and 24 ppm for Pb and 0, 0.5,
1, 2, 4, 6, 8 and 10 ppm for Cd. The properties of baker's yeast
quality were decreased by the increase of Pb or Cd in growth
medium. The slope values of yield, total viable cells and gassing
power of produced baker's yeast were investigated as an indicator of
metal resistant. In addition, concentrations of Pb and Cd in produced
baker's yeast were determined. The strain of S. cerevisiae FH-620
had the highest resistance against Pb and Cd and had the minimum
levels of both two investigated metals in produced baker's yeast.
Abstract: This work reports the potential of using Palm Kernel
(PK) ash and shell as a partial substitute for Portland Cement (PC)
and coarse aggregate in the development of mortar and concrete. PK
ash and shell are agro-waste materials from palm oil mills, the
disposal of PK ash and shell is an environmental problem of concern.
The PK ash has pozzolanic properties that enables it as a partial
replacement for cement and also plays an important role in the
strength and durability of concrete, its use in concrete will alleviate
the increasing challenges of scarcity and high cost of cement. In order
to investigate the PC replacement potential of PK ash, three types of
PK ash were produced at varying temperature (350-750C) and they
were used to replace up to 50% PC. The PK shell was used to replace
up to 100% coarse aggregate in order to study its aggregate
replacement potential. The testing programme included material
characterisation, the determination of compressive strength, tensile
splitting strength and chemical durability in aggressive sulfatebearing
exposure conditions. The 90 day compressive results showed
a significant strength gain (up to 26.2 N/mm2). The Portland cement
and conventional coarse aggregate has significantly higher influence
in the strength gain compared to the equivalent PK ash and PK shell.
The chemical durability results demonstrated that after a prolonged
period of exposure, significant strength losses in all the concretes
were observed. This phenomenon is explained, due to lower change
in concrete morphology and inhibition of reaction species and the
final disruption of the aggregate cement paste matrix.
Abstract: In this study, we have focused our attention on
combining of molecular imprinting into nanofilms and QCM
nanosensor approaches and producing QCM nanosensor for anti-
CCP, chosen as model protein, using anti-CCP imprinted nanofilms.
The nonimprinted nanosensor was also prepared to evaluate the
selectivity of the imprinted nanosensor. Anti-CCP imprinted QCM
nanosensor was tested for real time detection of anti-CCP from
aqueous solution. The kinetic and affinity studies were determined by
using anti-CCP solutions with different concentrations. The
responses related with mass shifts (%m) and frequency shifts (%f)
were used to evaluate adsorption properties. To show the selectivity
of the anti-CCP imprinted QCM nanosensor, competitive adsorption
of anti-CCP and IgM was investigated. The results indicate that anti-
CCP imprinted QCM nanosensor has higher adsorption capabilities
for anti-CCP than for IgM, due to selective cavities in the polymer
structure.
Abstract: In rapid industrial development, the demand for
high-strength and lightweight materials have been increased. Thus,
various CFRP (Carbon Fiber Reinforced Plastics) with composite
materials are being used. The design variables of CFRP are its
lamination direction, order and thickness. Thus, the hardness and
strength of CFRP depends much on their design variables. In this
paper, the lamination direction of CFRP was used to produce a
symmetrical ply [0°/0°, -15°/+15°, -30°/+30°, -45°/+45°, -60°/+60°,
-75°/+75° and 90°/90°] and an asymmetrical ply [0°/15°, 0°/30°,
0°/45°, 0°/60° 0°/75° and 0°/90°]. The bending flexure stress of the
CFRP specimen was evaluated through a bending test. Its thermal
property was measured using an infrared camera. The symmetrical
specimen and the asymmetrical specimen were analyzed. The results
showed that the asymmetrical specimen increased the bending loads
according to the increase in the orientation angle; and from 0°, the
symmetrical specimen showed a tendency opposite the asymmetrical
tendency because the tensile force of fiber differs at the vertical
direction of its load. Also, the infrared camera showed that the thermal
property had a trend similar to that of the mechanical properties.
Abstract: A computational fluid dynamics (CFD) model is
developed for rechargeable non-aqueous electrolyte lithium-air
batteries with a partial opening for oxygen supply to the cathode.
Multi-phase transport phenomena occurred in the battery are
considered, including dissolved lithium ions and oxygen gas in the
liquid electrolyte, solid-phase electron transfer in the porous
functional materials and liquid-phase charge transport in the
electrolyte. These transport processes are coupled with the
electrochemical reactions at the active surfaces, and effects of
discharge reaction-generated solid Li2O2 on the transport properties
and the electrochemical reaction rate are evaluated and implemented
in the model. The predicted results are discussed and analyzed in terms
of the spatial and transient distribution of various parameters, such as
local oxygen concentration, reaction rate, variable solid Li2O2 volume
fraction and porosity, as well as the effective diffusion coefficients. It
is found that the effect of the solid Li2O2 product deposited at the solid
active surfaces is significant on the transport phenomena and the
overall battery performance.
Abstract: The paper deals with the diagnostics of steel roof
structure of the winter sports halls built in 1970 year. The necessity
of the diagnostics has been given by the requirement to the evaluation
design of this structure, which has been caused by the new situation
in the field of the loadings given by the validity of the European
Standards in the Czech Republic from 2010 year. Due to these
changes in the normative rules, in practice existing structures are
gradually subjected to the evaluation design and depending on its
results to the strengthening or reconstruction, respectively. Steel roof
is composed of plane truss main girders, purlins and bracings and the
roof structure is supported by two arch main girders with the span of
L = 84 m. The in situ diagnostics of the roof structure was oriented to
the following parts: (i) determination and evaluation of the actual
material properties of used steel and (ii) verification of the actual
dimensions of the structural members. For the solution the nondestructive
methods have been used for in situ measurement. For the
indicative determination of steel strengths the modified method based
on the determination of Rockwell’s hardness has been used. For the
verification of the member’s dimensions (thickness of hollow
sections) the ultrasound method has been used. This paper presents
the results obtained using these testing methods and their evaluation,
from the viewpoint of the usage for the subsequent static assessment
and design evaluation of the existing structure. For the comparison,
the examples of the similar evaluations realized for steel structures of
the stadiums in Olomouc and Jihlava cities are briefly illustrated, too.
Abstract: In this paper, we have compared and analyzed the
electroabsorption properties between with and without excitonic
effect bulk in high purity GaAs spatial light modulator for optical
fiber communication network. The eletroabsorption properties such
as absorption spectra, change in absorption spectra, change in
refractive index and extinction ration has been calculated. We have
also compared the result of absorption spectra and change in
absorption spectra with the experimental results and found close
agreement with experimental results.
Abstract: Load modeling is one of the central functions in
power systems operations. Electricity cannot be stored, which means
that for electric utility, the estimate of the future demand is necessary
in managing the production and purchasing in an economically
reasonable way. A majority of the recently reported approaches are
based on neural network. The attraction of the methods lies in the
assumption that neural networks are able to learn properties of the
load. However, the development of the methods is not finished, and
the lack of comparative results on different model variations is a
problem. This paper presents a new approach in order to predict the
Tunisia daily peak load. The proposed method employs a
computational intelligence scheme based on the Fuzzy neural
network (FNN) and support vector regression (SVR). Experimental
results obtained indicate that our proposed FNN-SVR technique gives
significantly good prediction accuracy compared to some classical
techniques.
Abstract: Elastomeric dielectric material has recently become a
new alternative for actuator technology. The characteristics of
dielectric elastomers placed between two electrodes to withstand
large strain when electrodes are charged has attracted the attention of
many researcher to study this material for actuator technology. Thus,
in the past few years Danfoss Ventures A/S has established their own
dielectric electro-active polymer (DEAP), which was called
PolyPower.
The main objective of this work was to investigate the dynamic
characteristics for vibration control of a PolyPower actuator folded in
‘pull’ configuration. A range of experiments was carried out on the
folded actuator including passive (without electrical load) and active
(with electrical load) testing. For both categories static and dynamic
testing have been done to determine the behavior of folded DEAP
actuator.
Voltage-Strain experiments show that the DEAP folded actuator is
a non-linear system. It is also shown that the voltage supplied has no
effect on the natural frequency. Finally, varying AC voltage with
different amplitude and frequency shows the parameters that
influence the performance of DEAP folded actuator. As a result, the
actuator performance dominated by the frequency dependence of the
elastic response and was less influenced by dielectric properties.
Abstract: Geometric and mechanical properties all influence the
resistance of RC structures and may, in certain combination of
property values, increase the risk of a brittle failure of the whole
system.
This paper presents a statistical and probabilistic investigation on
the resistance of RC beams designed according to Eurocodes 2 and 8,
and subjected to multiple failure modes, under both the natural
variation of material properties and the uncertainty associated with
cross-section and transverse reinforcement geometry. A full
probabilistic model based on JCSS Probabilistic Model Code is
derived. Different beams are studied through material nonlinear
analysis via Monte Carlo simulations. The resistance model is
consistent with Eurocode 2. Both a multivariate statistical evaluation
and the data clustering analysis of outcomes are then performed.
Results show that the ultimate load behaviour of RC beams
subjected to flexural and shear failure modes seems to be mainly
influenced by the combination of the mechanical properties of both
longitudinal reinforcement and stirrups, and the tensile strength of
concrete, of which the latter appears to affect the overall response of
the system in a nonlinear way. The model uncertainty of the
resistance model used in the analysis plays undoubtedly an important
role in interpreting results.
Abstract: Thin ZnO films are deposited on glass substrates via
sol–gel method and dip-coating. The films are prepared from zinc
acetate dehydrate as a starting reagent. After that the as-prepared
ZnO sol is aged for different periods (0, 1, 3, 5, 10, 15 and 30 days).
Nanocrystalline thin films are deposited from various sols. The
effect ZnO sols aging time on the structural and photocatalytic
properties of the films is studied. The films surface is studied by
Scanning Electron Microscopy. The effect of the aging time of the
starting solution is studied in the photocatalytic degradation of
Reactive Black 5 (RB5) by UV-vis spectroscopy. The experiments
are conducted upon UV-light illumination and in complete darkness.
The variation of the absorption spectra shows the degradation of RB5
dissolved in water, as a result of the reaction, occurring on the surface
of the films and promoted by UV irradiation. The initial
concentrations of dye (5, 10 and 20 ppm) and the effect of the aging
time are varied during the experiments. The results show, that the
increasing aging time of starting solution with respect to ZnO
generally promotes photocatalytic activity. The thin films obtained
from ZnO sol, which is aged 30 days have best photocatalytic
degradation of the dye (97,22%) in comparison with the freshly
prepared ones (65,92%). The samples and photocatalytic
experimental results are reproducible. Nevertheless, all films exhibit
a substantial activity in both UV light and darkness, which is
promising for the development of new ZnO photocatalysts by sol-gel
method.
Abstract: The temperature dependence of wettability (wetting
angle, Θ (T)) for Ag-based melts on graphite and Al2O3 substrates is
compared. Typical alloying effects are found, as the Ag host metal is
gradually replaced by various metallic elements. The essence of
alloying lies in the change of the electron/atom (e/a) ratio. This ratio
is also manifested in the shift of wetting angles on the same substrate.
Nevertheless, the effects are partially smeared by other
(metallurgical) factors, like the interaction between the oxygenalloying
elements and by the graphite substrate-oxygen interaction. In
contrast, such effects are not pronounced in the case of Al2O3
substrates. As a consequence, Θ(T) exhibits an opposite trend in the
case of two substrates. Crossovers of the Θ(T) curves were often
found. The positions of crossovers depend on the chemical character
and concentration of solute atoms. Segregation and epitaxial texture
formation after solidification were also observed in certain alloy
drops, especially in high concentration range. This phenomenon is
not yet explained in every detail.
Abstract: Waste silicon carbide (waste SiC) filled high-density
polyethylene (HDPE) with and without surface modifiers were
studied. Two types of surface modifiers namely; high-density
polyethylene-grafted-maleic anhydride (HDPE-g-MA) and 3-aminopropyltriethoxysilane have been used in this study. The
composites were produced using a two roll mill, extruder and shaped
in a hydraulic compression molding machine. The mechanical
properties of polymer composites such as flexural strength and
modulus, impact strength, tensile strength, stiffness and hardness
were investigated over a range of compositions. It was found that,
flexural strength and modulus, tensile modulus and hardness
increased, whereas impact strength and tensile strength decreased
with the increasing in filler contents, compared to the neat HDPE. At
similar filler content, the effect of both surface modifiers increased
flexural modulus, impact strength, tensile strength and stiffness but
reduced the flexural strength. Morphological investigation using
SEM revealed that the improvement in mechanical properties was
due to enhancement of the interfacial adhesion between waste SiC
and HDPE.
Abstract: The dielectric properties and ionic conductivity of
novel "ceramic state" polymer electrolytes for high capacity lithium
battery are characterized by Radio frequency and Microwave
methods in two broad frequency ranges from 50 Hz to 20 KHz and 4
GHz to 40 GHz. This innovative solid polymer electrolyte which is
highly ionic conductive (10-3 S/cm at room temperature) from -40oC
to +150oC can be used in any battery application. Such polymer
exhibits properties more like a ceramic rather than polymer. The
various applied measurement methods produced accurate dielectric
results for comprehensive analysis of electrochemical properties and
ion transportation mechanism of this newly invented polymer
electrolyte. Two techniques and instruments employing air gap
measurement by Capacitance Bridge and in-waveguide measurement
by vector network analyzer are applied to measure the complex
dielectric spectra. The complex dielectric spectra are used to
determine the complex alternating current electrical conductivity and
thus the ionic conductivity.
Abstract: Sandwich structure composites produced by epoxy
core and aluminium skin were developed as potential building
materials. Interface bonding between core and skin was controlled by
varying kenaf content. Five different weight percentage of kenaf
loading ranging from 10 wt% to 50 wt% were employed in the core
manufacturing in order to study the mechanical properties of the
sandwich composite. Properties of skin aluminium with epoxy were
found to be affected by drying time of the adhesive. Mechanical
behavior of manufactured sandwich composites in relation with
properties of constituent materials was studied. It was found that 30
wt% of kenaf loading contributed to increase the flexural strength and
flexural modulus up to 102 MPa and 32 GPa, respectively. Analysis
were done on the flatwise and edgewise compression test. For
flatwise test, it was found that 30 wt% of fiber loading could
withstand maximum force until 250 kN, with compressive strength
results at 96.94 MPa. However, at edgewise compression test, the
sandwich composite with same fiber loading only can withstand 31
kN of the maximum load with 62 MPa of compressive strength
results.
Abstract: Ocimum americanum L (Lamiaceae) is an annual herb
that is native to tropical Africa. The in vitro and in vivo antioxidant
activity of its aqueous extract was carefully investigated by assessing
the DPPH radical scavenging activity, ABTS radical scavenging
activity and hydrogen peroxide radical scavenging activity. The
reducing power, total phenol, total flavonoids and flavonols content
of the extract were also evaluated. The data obtained revealed that the
extract is rich in polyphenolic compounds and scavenged the radicals
in a concentration dependent manner. This was done in comparison
with the standard antioxidants such as BHT and Vitamin C. Also, the
induction of oxidative damage with paracetamol (2000 mg/kg)
resulted in the elevation of lipid peroxides and significant (P < 0.05)
decrease in activities of superoxide dismutase, glutathione
peroxidase, glutathione reductase and catalase in the liver and kidney
of rats. However, the pretreatment of rats with aqueous extract of O.
americanum leaves (200 and 400 mg/kg) and silymarin (100 mg/kg)
caused a significant (P < 0.05) reduction in the values of lipid
peroxides and restored the levels of antioxidant parameters in these
organs. These findings suggest that the leaves of O. americanum have
potent antioxidant properties which may be responsible for its
acclaimed folkloric uses.
Abstract: The present study was undertaken to investigate the
effect of aging parameters (time and temperature) on the mechanical
properties of Be-and/or Zr- treated Al-Mg-Zn (7075) alloys. Ultimate
tensile strength, 0.5% offset yield strength and % elongation
measurements were carried out on specimens prepared from cast and
heat treated 7075 alloys containing Be and/or Zr. Different aging
treatment were carried out for the as solution treated (SHT)
specimens (after quenching in warm water). The specimens were
aged at different conditions; Natural and artificial aging was carried
out at room temperature, 120C, 150C, 180C and 220C for different
periods of time. Duplex aging was performed for SHT conditions
(pre-aged at different time and temperature followed by high
temperature aging). Ultimate tensile strength, yield strength and %
elongation data results as a function of different aging parameters are
analysed. A statistical design of experiments (DOE) approach using
fractional factorial design is applied to acquire an understanding of
the effects of these variables and their interactions on the mechanical
properties of Be- and/or Zr- treated 7075 alloys. Mathematical
models are developed to relate the alloy mechanical properties with
the different aging parameters.
Abstract: The Standard Penetration Test (SPT) is the most
common in situ test for soil investigations. On the other hand, the
Cone Penetration Test (CPT) is considered one of the best
investigation tools. Due to the fast and accurate results that can be
obtained it complaints the SPT in many applications like field
explorations, design parameters, and quality control assessments.
Many soil index and engineering properties have been correlated to
both of SPT and CPT. Various foundation design methods were
developed based on the outcome of these tests. Therefore it is vital to
correlate these tests to each other so that either one of the tests can be
used in the absence of the other, especially for preliminary evaluation
and design purposes.
The primary purpose of this study was to investigate the
relationships between the SPT and CPT for different type of sandy
soils in Florida. Data for this research were collected from number of
projects sponsored by the Florida Department of Transportation
(FDOT), six sites served as the subject of SPT-CPT correlations. The
correlations were established between the cone resistance (qc), sleeve
friction (fs) and the uncorrected SPT blow counts (N) for various
soils.
A positive linear relationship was found between qc, fs and N for
various sandy soils. In general, qc versus N showed higher
correlation coefficients than fs versus N. qc/N ratios were developed
for different soil types and compared to literature values, the results
of this research revealed higher ratios than literature values.
Abstract: The industrial process adds to engineering wood
products features absent in solid wood, with homogeneous structure
and reduced defects, improved physical and mechanical properties,
bio-deterioration, resistance and better dimensional stability,
improving quality and increasing the reliability of structures wood.
These features combined with using fast-growing trees, make them
environmentally ecological products, ensuring a strong consumer
market. The wood I-joists are manufactured by the industrial profiles
bonding flange and web, an important aspect of the production of
wooden I-beams is the adhesive joint that bonds the web to the
flange. Adhesives can effectively transfer and distribute stresses,
thereby increasing the strength and stiffness of the composite. The
objective of this study is to evaluate different resins in a shear strain
specimens with the aim of analyzing the most efficient resin and
possibility of using national products, reducing the manufacturing
cost. First was conducted a literature review, where established the
geometry and materials generally used, then established and analyzed
8 national resins and produced six specimens for each.
Abstract: Physical properties of uranium dinitride (UN2) were
investigated in detail using first principle calculations based on
density functional theory (DFT). To study the strong correlation
effects due to 5f uranium valence electrons, the on-site coulomb
interaction correction U via the Hubbard-like term (DFT+U) was
employed. The UN2 structural, mechanical and thermodynamic
properties were calculated within DFT and Various U of DFT+U
approach.
The Perdew–Burke–Ernzerhof (PBE.5.2) version of the
generalized gradient approximation (GGA) is used to describe the
exchange-correlation with the projector-augmented wave (PAW)
pseudo potentials.
A comparative study shows that results are improved by using the
Hubbard formalism for a certain U value correction like the structural
parameter. For some physical properties the variation versus
Hubbard-U is strong like Young modulus but for others it is weakly
noticeable such as bulk modulus.
We noticed also that from U=7.5 eV, elastic results don’t agree
with the cubic cell because of the C44 values which turn out to be
negative.