The Effect of Surface Modifiers on the Mechanical and Morphological Properties of Waste Silicon Carbide Filled High-Density Polyethylene

Waste silicon carbide (waste SiC) filled high-density
polyethylene (HDPE) with and without surface modifiers were
studied. Two types of surface modifiers namely; high-density
polyethylene-grafted-maleic anhydride (HDPE-g-MA) and 3-aminopropyltriethoxysilane have been used in this study. The
composites were produced using a two roll mill, extruder and shaped
in a hydraulic compression molding machine. The mechanical
properties of polymer composites such as flexural strength and
modulus, impact strength, tensile strength, stiffness and hardness
were investigated over a range of compositions. It was found that,
flexural strength and modulus, tensile modulus and hardness
increased, whereas impact strength and tensile strength decreased
with the increasing in filler contents, compared to the neat HDPE. At
similar filler content, the effect of both surface modifiers increased
flexural modulus, impact strength, tensile strength and stiffness but
reduced the flexural strength. Morphological investigation using
SEM revealed that the improvement in mechanical properties was
due to enhancement of the interfacial adhesion between waste SiC
and HDPE.

• R. Dangtungee
• A. Rattanapan
• S. Siengchin

• High-density polyethylene
• HDPE-g-MA
• mechanical properties
• morphological properties
• silicon carbide
• waste silicon carbide.

[1] D. Nwabunma and T. Kyu, Polyolefin composites, Canada: Wiley New,
2008.
[2] F. C. Chiu, H. Z. Yen, and C. E. Lee, “Characterization of PP/HDPE
blend-based nanocomposites using different maleated polyolefins as
compatibilizers,” Polymer Testing, vol. 29, pp. 397-406, May 2010.
[3] N. Othman, H. Ismail, and M. Mariatti, “Effect of compatibilisers on
mechanical and thermal properties of bentonite filled polypropylene
composites,” Polymer Degradation and Stability, vol. 91, pp. 1761-
1774, August 2006.
[4] H. Ismail, J. M. Nizam, and H. P. S. Abdul Khalil, “The effect of a
compatibilizer on the mechanical properties and mass swell of white rice
husk ash filled natural rubber/linear low density polyethylene blend,”
Polymer Testing, vol. 20, pp. 125–133, October 2001.
[5] O. H. Lin, Z. A. M. Ishak, and H. M. Akil, “Preparation and properties
of nanosilica-filled polypropylene composites with PP-methyl POSS as
compatibilizer,” Materials and Design, vol. 30, pp. 748-751, March
2009.
[6] B. Kouini, and A. Serier, “Properties of polypropylene/polyamide
nanocomposites prepared by melt processing with a PP-g-MAH
compatibilizer,” Materials and Design, vol. 34, pp. 313-318, February
2012.
[7] D. N. Bikiaris, A. Vassiliou, E. Pavlidou, and G. P. Karayannidis,
“Compatibilisation effect of PP-g-MA copolymer on iPP/SiO2
nanocomposites prepared by melt mixing,” European Polymer Journal,
vol. 4, pp. 1965-1978, September 2005.
[8] H. Shen, Y. Wang, and K. Mai, “Effect of compatibilizers on the
thermal stability and mechanical properties of magnesium hydroxide
filled polypropylene composites,” Thermochimica Acta, vol. 483, pp.
36-40, February 2009.
[9] D. Bikiaris, J. Prinos, K. Koutsopoulos, N. Vouroutzis, E. Pavlidou, N.
Frangis, and C. Panayiotou, “LDPE/plasticized starch blends containing
PE-g-MA copolymer as compatibilizer,” Polymer Degradation and
Stability, vol. 59, pp. 287-291, January 1998.
[10] E. F. Marques, J. A. Mendez, M. A. Pelach, F. Vilaseca, J. Bayer, and P.
Mutje, “Influence of coupling agents in the preparation of polypropylene
composites reinforced with recycled fibers,” Chemical Engineering
Journal, vol. 166, pp. 1170-1178, February 2011.
[11] M. Buggy, G. Bradley, and A. Sullivan, “Polymer–filler interactions in
kaolin/nylon 6,6 composites containing a silane coupling agent,”
Composites: Part A, vol. 36, pp. 437–442, April 2005.
[12] S. B. Elvy, G. R. Dennis, and L. T. Ng, “Effects of coupling agent on the
physical properties of wood-polymer composites”, Journal Material
Processing Technology, vol. 48, pp. 365-372, January 1995.
[13] Z. Demjen, B. Pukanszky, and J. N. Jr, “Possible coupling reactions of
functional silanes and polypropylene,” Polymer, vol. 40, pp. 1763-1773,
March 1999.
[14] R. Yang, Y. Liu, K. Wang, and J. Yu, “Characterization of surface
interaction of inorganic fillers with silane coupling agents,” Journal of
analytical and applied pyrolysis, vol. 70, pp. 413-425, December 2003.
[15] P. G. Pape, Applied Plastics Engineering Handbook, USA: Elsevier,
2011.
[16] Y. Xie, C. A. S. Hill, Z. Xiao, H. Militz, and C. Mai, “Silane coupling
agents used for natural fiber/polymer composites: A review,”
Composites: Part A, vol. 41, pp. 806-819, July 2010.
[17] Z. Demjen, B. Pukanszky, E. Foldes, and J. Nagy, “Interaction of silane
coupling agents with CaCO3,” Journal of Colloid Interface Science, vol.
190, pp. 427-436, June 1997. [18] J. H. Lee, D. Jung, C. E. Hong, L. Y. Rhee, and S. G. Advani,
“Properties of polyethylene-layered silicate nanocomposites prepared by
melt intercalation with a PP-g-MA compatibilizer,” Composites Science
and Technology, vol. 65, pp. 1996-2002, October 2005.
[19] S. Filippi, C. Marazzato, P. Magagnini, A. Famulari, P. Arosio, and S.
V. Meille, “Structure and morphology of HDPE-g-MA/organoclay
nanocomposites: Effects of the preparation procedures,” European
Polymer Journal, vol. 44, pp. 987-1002, April 2008.
[20] G. W. Lee, M. Park, J. Kima, J. Ik Lee, and H. G. Yoon, “Enhanced
thermal conductivity of polymer composites filled with hybrid filler,”
Composites: Part A, vol. 37, pp. 727–734, May 2006.
[21] F. Yang, and V. Hlavacek, “Improvement of PVC wearability by
addition of additives,” Powder Technology, vol. 103, pp.182–188, July
1999.