Abstract: The purpose of the present study is to analyze the
effect of the target plate-s curvature on the heat transfer in laminar
confined impinging jet flows. Numerical results from two
dimensional compressible finite volume solver are compared
between three different shapes of impinging plates: Flat, Concave
and Convex plates. The remarkable result of this study proves that
the stagnation Nusselt number in laminar range of Reynolds number
based on the slot width is maximum in convex surface and is
minimum in concave plate. These results refuse the previous data in
literature stating the amount of the stagnation Nusselt number is
greater in concave surface related to flat plate configuration.
Abstract: This paper characterizes the effects of artificial short
term aging in the laboratory on the rheological properties of virgin
80/100 penetration grade asphalt binder. After several years in
service, asphalt mixture started to deteriorate due to aging. Aging is a
complex physico-chemical phenomenon that influences asphalt
binder rheological properties causing a deterioration in asphalt
mixture performance. To ascertain asphalt binder aging effects, the
virgin, artificially aged and extracted asphalt binder were tested via
the Rolling Thin film Oven (RTFO), Dynamic Shear Rheometer
(DSR) and Rotational Viscometer (RV). A comparative study
between laboratory and field aging conditions were also carried out.
The results showed that the specimens conditioned for 85 minutes
inside the RTFO was insufficient to simulate the actual short term
aging caused that took place in the field under Malaysian field
conditions
Abstract: Earlier studies in kinship networks have primarily
focused on observing the social relationships existing between family
relatives. In this study, we pre-identified hubs in the network to
investigate if they could play a catalyst role in the transfer of physical
information. We conducted a case study of a ceremony performed in
one of the families of a small Hindu community – the Uttar Rarhi
Kayasthas. Individuals (n = 168) who resided in 11 geographically
dispersed regions were contacted through our hub-based
representation. We found that using this representation, over 98% of
the individuals were successfully contacted within the stipulated
period. The network also demonstrated a small-world property, with
an average geodesic distance of 3.56.
Abstract: This research aimed to study the competency of health
and wellness hotels and resorts in developing use the local natural
resources and wisdom to conform to the national health and wellness
tourism (HWT) strategy by comparing two independent samples,
from Aumpur Muang, Ranong province and Aumpur Muang,
Chiangmai province. And also study in the suggestive direct path to
lead the organization to the sustainable successful.
This research was conduct by using mix methodology; both
quantitative and qualitative data were used. The data of competency
of health and wellness hotels and resorts (HWHR) in developing use
the local natural resources for HWT promoting were collected via
300 set of questionnaires, from 6 hotels and resorts in 2 areas, 3
places from Aumpur Muang, Ranong province and another 3 from
Aumpur Muang, Chiangmai province.
Thestudy of HWHR’s competency in developing use the local
natural resources and wisdom to conform to the national HWT
strategycan be divided into fourmain areas, food and beverages
service, tourism activity, environmental service, and value adding.
The total competency of the Chiangmai sample is importantly
scoredp. value 0.01 higher than the Ranong one while the area of
safety, Chiangmai’s competency is importantly scored 0.05 higher
than the Ranong’scompetency. Others were rated not differently.
Since Chiangmai perform better, then it can be a role model in
developing HTHR or HWT destination.
From the part of qualitative research, content analysis of business
contents and its environments were analyzed. The four stages of
strategic development and plans, from the smallest scale to the largest
scale such a national base were discussed. The HWT: Evolution
model and strategy for lodging Business were suggested. All those
stages must work harmoniously together. The distinctive result
illustrates the need of human resource development as the key point
to create the identity of Thainess on Health and wellness service
providing. This will add-on the value of services and differentiates
ourselves from other competitors. The creative of Thailand’s health
and wellness brand possibly increase loyalty customers which agreed
to be a path of sustainable development.
Abstract: As is known, one of the priority directions of research
works of natural sciences is introduction of applied section of
contemporary mathematics as approximate and numerical methods to
solving integral equation into practice. We fare with the solving of
integral equation while studying many phenomena of nature to whose
numerically solving by the methods of quadrature are mainly applied.
Taking into account some deficiency of methods of quadrature for
finding the solution of integral equation some sciences suggested of
the multistep methods with constant coefficients. Unlike these papers,
here we consider application of hybrid methods to the numerical
solution of Volterra integral equation. The efficiency of the suggested
method is proved and a concrete method with accuracy order p = 4
is constructed. This method in more precise than the corresponding
known methods.
Abstract: Nowadays, doping is an intricate dilemma. Wrestling
is the nationally popular sport in Iran. Also the prevalence of doping
may be high, due to its power demanding characteristics. So, we
aimed to assess the knowledge and attitudes toward doping among
the club wrestlers. In a cross sectional study, 426 wrestlers were
studied. For this reason, a researcher made questionnaire was used. In
this study, researchers selected the clubs by randomized clustered
sampling and distributed the questionnaire among wrestlers.
Knowledge of wrestlers in three categories of doping definitions,
recognition of prohibited drugs and side effects was poor or moderate
in 70.8%, 95.8% and 99.5%, respectively. Wrestlers have poor
knowledge in doping. Furthermore, they believe some myths which
are unfavorable. It seems necessary to design a comprehensive
educational program for all of the athletes and coaches.
Abstract: The selective wet-etching of amorphous and
crystalline region of Sb20Se80 thin films was carried out using organic
based solution e.g. amines. We report the development of an in situ
real-time method to study the wet chemical etching process of thin
films. Characterization of the structure and surface of films studied
by X-ray diffraction, SEM and EBSD methods has been done and
potential application suggested.
Abstract: This paper presents the study of induced currents and
temperature distribution in gear heated by induction process using 2D
finite element (FE) model. The model is developed by coupling
Maxwell and heat transfer equations into a multi-physics model. The
obtained results allow comparing the medium frequency (MF) and
high frequency (HF) cases and the effect of machine parameters on
the evolution of induced currents and temperature during heating.
The sensitivity study of the temperature profile is conducted and the
case hardness is predicted using the final temperature profile. These
results are validated using tests and give a good understanding of
phenomena during heating process.
Abstract: Eco-driving allows the driver to optimize his/her behaviour in order to achieve several types of benefits: reducing pollution emissions, increasing road safety, and fuel saving. One of the main rules for adopting eco-driving is to anticipate the traffic events by avoiding strong acceleration or braking and maintaining a steady speed when possible. Therefore, drivers have to comply with speed limits and time headway. The present study explored the role of three types of motivation and social norms in predicting French drivers- intentions to comply with speed limits and time headway as eco-driving practices as well as examine the variations according to gender and age. 1234 drivers with ages between 18 and 75 years old filled in a questionnaire which was presented as part of an online survey aiming to better understand the drivers- road habits. It included items assessing: a) behavioural intentions to comply with speed limits and time headway according to three types of motivation: reducing pollution emissions, increasing road safety, and fuel saving, b) subjective and descriptive social norms regarding the intention to comply with speed limits and time headway, and c) sociodemographical variables. Drivers expressed their intention to frequently comply with speed limits and time headway in the following 6 months; however, they showed more intention to comply with speed limits as compared to time headway regardless of the type of motivation. The subjective injunctive norms were significantly more important in predicting drivers- intentions to comply with speed limits and time headway as compared to the descriptive norms. In addition, the most frequently reported type of motivation for complying with speed limits and time headway was increasing road safety followed by fuel saving and reducing pollution emissions, hence underlining a low motivation to practice eco-driving. Practical implications of the results are discussed.
Abstract: Having a very many number of pipelines all over the
country, Iran is one of the countries consists of various ecosystems
with variable degrees of fragility and robusticity as well as
geographical conditions. This study presents a state-of-the-art method
to estimate environmental risks of pipelines by recommending
rational equations including FES, URAS, SRS, RRS, DRS, LURS
and IRS as well as FRS to calculate the risks. This study was carried
out by a relative semi-quantitative approach based on land uses and
HVAs (High-Value Areas). GIS as a tool was used to create proper
maps regarding the environmental risks, land uses and distances. The
main logic for using the formulas was the distance-based approaches
and ESI as well as intersections. Summarizing the results of the
study, a risk geographical map based on the ESIs and final risk score
(FRS) was created. The study results showed that the most sensitive
and so of high risk area would be an area comprising of mangrove
forests located in the pipeline neighborhood. Also, salty lands were
the most robust land use units in the case of pipeline failure
circumstances. Besides, using a state-of-the-art method, it showed
that mapping the risks of pipelines out with the applied method is of
more reliability and convenience as well as relative
comprehensiveness in comparison to present non-holistic methods for
assessing the environmental risks of pipelines. The focus of the
present study is “assessment" than that of “management". It is
suggested that new policies are to be implemented to reduce the
negative effects of the pipeline that has not yet been constructed
completely
Abstract: The people are differed by their capabilities, skills and mental agilities. The evolution of human from childhood when they are completely dependent up to adultness the time they gradually set the dependency free is too complicated, by considering they have all started from almost one point but some become cleverer and some less. The main control command of a cybernetic hand should be posted by remaining healthy organs of disabled Person. These commands can be from several channels, which their recording and detecting are different and need complicated study. In this research, we suppose that, this stage has been done or in the other words, the command has been already sent and detected. So the main goal is to control a long hand, upper elbow hand missing, by an interest angle define by disabled. It means that, the system input is the position desired by disables and the output is the elbow-joint angle variation. Therefore the goal is a suitable control design based on neural network theory in order to meet the given mapping.
Abstract: The main aim of the presented experiments is to
improve behaviour of sandwich structures under dynamic loading,
such as crash or explosion. Several cellular materials are widely used
as core of the sandwich structures and their properties influence
the response of the entire element under impact load. To optimize
their performance requires the characterisation of the core material
behaviour at high strain rates and identification of the underlying
mechanism. This work presents the study of high strain-rate
characteristics of a specific porous lightweight blast energy absorbing
foam using a Split Hopkinson Pressure Bar (SHPB) technique
adapted to perform tests on low strength materials. Two different
velocities, 15 and 30 m.s-1 were used to determine the strain
sensitivity of the material. Foams were designed using two types of
porous lightweight spherical raw materials with diameters of 30-
100 *m, combined with polymer matrix. Cylindrical specimens with
diameter of 15 mm and length of 7 mm were prepared and loaded
using a Split Hopkinson Pressure Bar apparatus to assess the relation
between the composition of the material and its shock wave
attenuation capacity.
Abstract: The motorway segment between Tangier and Oued
R’mel has experienced, since the beginning of building works,
significant instability and landslides linked to a number of geological,
hydrogeological and geothermic factors affecting the different
formations.
The landslides observed are not fully understood, despite many
studies conducted on this segment. This study aims at producing new
methods to better explain the phenomena behind the landslides,
taking into account the geotechnical and geothermic contexts. This
analysis builds up on previous studies and geotechnical data collected
in the field.
The final body of data collected shall be processed through the
Plaxis software for a better and customizable view of the landslide
problems in the area, which will help tofind solutions and stabilize
land in the area.
Abstract: Film, as an art form playing a vital role and is a powerful tool in documenting, influencing and shaping the society. Films are the collective creation of a large number of separate individuals, each contributing with creative input, unique talents, and technical expertise to the project. Recently, the Malaysian Independent (or “Indie") filmmakers have made their presence felt by winning awards at various international film festivals. Working in the digital video (DV) format, a number of independent filmmakers really hit their stride with a range of remarkably strong titles and international recognition has been quick in coming and their works are now regularly in exhibition or in competition, winning many top prizes at prestigious festivals around the world. The interaction factors among crewmembers are emphasized as imperative for group success. An in-depth interview is conducted to analyze the social interactions and exchanges between filmmakers through Social Exchanges Theory (SET). Certainly the new millennium that was marked as the digital technology revolution has changed the face of filmmaking in Malaysia. There is a clear need to study the Malaysian independent cinema especially from the perspective of understanding what causes the independent filmmakers to work so well given all of the difficulties and constraints.
Abstract: This paper contributes to the field of Environmental
Awareness Training (EAT) evaluation in terms of military activities.
Environmental management of military activities is a growing concern
for defence forces worldwide and the importance of EAT is becoming
widely recognized. As one of Australia-s largest landowners, the
Australian Defence Force (ADF) is extremely mindful of its duty as a
joint environmental manager. It has an integrated Environmental
Management System (EMS) to assist environmental management and
EAT is an essential part of the ADF EMS model. This paper examines
how EAT was conducted during the exercise Talisman Saber in 2009
(TS09) and evaluates its effectiveness, using Shoalwater Bay Training
Area (SWBTA), one of the most significant military training areas and
a significant protected area in Australia, as a case study. A
questionnaire survey conducted showed, overall, that EAT was
effective from the perspective of a sample of participants.
Recommendations are made for the ADF to refine EAT for future
exercises.
Abstract: In this paper, an extended study is performed on the
effect of different factors on the quality of vector data based on a
previous study. In the noise factor, one kind of noise that appears in
document images namely Gaussian noise is studied while the previous
study involved only salt-and-pepper noise. High and low levels of
noise are studied. For the noise cleaning methods, algorithms that were
not covered in the previous study are used namely Median filters and
its variants. For the vectorization factor, one of the best available
commercial raster to vector software namely VPstudio is used to
convert raster images into vector format. The performance of line
detection will be judged based on objective performance evaluation
method. The output of the performance evaluation is then analyzed
statistically to highlight the factors that affect vector quality.
Abstract: Mass-mail type worms have threatened to become a large problem for the Internet. Although many researchers have analyzed such worms, there are few studies that consider worm propagation via mailing lists. In this paper, we present a mass-mailing type worm propagation model including the mailing list effect on the propagation. We study its propagation by simulation with a real e¬mail social network model. We show that the impact of the mailing list on the mass-mail worm propagation is significant, even if the mailing list is not large.
Abstract: This study is about an application of King Bhumibol
Adulyadej’s “Learn Wisely” (LW) concept in instructional design
and management process at the Faculty of Education, Suan Sunahdha
Rajabhat University. The concept suggests four strategies for true
learning. Related literature and significant LW methods in teaching
and learning are also reviewed and then applied in designing a
pedagogy learning module. The design has been implemented in
three classrooms with a total of 115 sophomore student teachers.
After one consecutive semester of managing and adjusting the
process by instructors and experts using collected data from minutes,
assessment of learning management, satisfaction and learning
achievement of the students, it is found that the effective SSRU
model of LW instructional method comprises of five steps.
Abstract: Computational study of two dimensional supersonic reacting hydrogen-air flows is performed to investigate the nitrogen effects on ignition delay time for premixed and diffusion flames. Chemical reaction is treated using detail kinetics and the advection upstream splitting method is used to calculate the numerical inviscid fluxes. The results show that just in stoichiometric condition for both premixed and diffusion flames, there is monotone dependency of the ignition delay time to the nitrogen addition. In other situations, the optimal condition from ignition viewpoint should be found using numerical investigations.
Abstract: The H.264/AVC standard uses an intra prediction, 9
directional modes for 4x4 luma blocks and 8x8 luma blocks, 4
directional modes for 16x16 macroblock and 8x8 chroma blocks,
respectively. It means that, for a macroblock, it has to perform 736
different RDO calculation before a best RDO modes is determined.
With this Multiple intra-mode prediction, intra coding of H.264/AVC
offers a considerably higher improvement in coding efficiency
compared to other compression standards, but computational
complexity is increased significantly. This paper presents a fast intra
prediction algorithm for H.264/AVC intra prediction based a
characteristic of homogeneity information. In this study, the gradient
prediction method used to predict the homogeneous area and the
quadratic prediction function used to predict the nonhomogeneous
area. Based on the correlation between the homogeneity and block
size, the smaller block is predicted by gradient prediction and
quadratic prediction, so the bigger block is predicted by gradient
prediction. Experimental results are presented to show that the
proposed method reduce the complexity by up to 76.07%
maintaining the similar PSNR quality with about 1.94%bit rate
increase in average.