Abstract: Indoor air environment is a big concern in the last few decades in the developing countries, with increased focus on monitoring the air quality. In this work, an experimental study has been conducted to establish the existence of carbon nanoparticles below the size range of 10 nm in the non-sooting zone of a LPG/air partially premixed flame. Mainly, four optical techniques, UV absorption spectroscopy, fluorescence spectroscopy, dynamic light scattering and TEM have been used to characterize and measure the size of carbon nanoparticles in the sampled materials collected from the inner surface of the flame front. The existence of the carbon nanoparticles in the sampled material has been confirmed with the typical nature of the absorption and fluorescence spectra already reported in the literature. The band gap energy shows that the particles are made up of three to six aromatic rings. The size measurement by DLS technique also shows that the particles below the size range of 10 nm. The results of DLS are also corroborated by the TEM image of the same material.
Abstract: This paper discusses the applicability of the numerical model for a damage prediction method of the accidental hydrogen explosion occurring in a hydrogen facility. The numerical model was based on an unstructured finite volume method (FVM) code “NuFD/FrontFlowRed”. For simulating unsteady turbulent combustion of leaked hydrogen gas, a combination of Large Eddy Simulation (LES) and a combustion model were used. The combustion model was based on a two scalar flamelet approach, where a G-equation model and a conserved scalar model expressed a propagation of premixed flame surface and a diffusion combustion process, respectively. For validation of this numerical model, we have simulated the previous two types of hydrogen explosion tests. One is open-space explosion test, and the source was a prismatic 5.27 m3 volume with 30% of hydrogen-air mixture. A reinforced concrete wall was set 4 m away from the front surface of the source. The source was ignited at the bottom center by a spark. The other is vented enclosure explosion test, and the chamber was 4.6 m × 4.6 m × 3.0 m with a vent opening on one side. Vent area of 5.4 m2 was used. Test was performed with ignition at the center of the wall opposite the vent. Hydrogen-air mixtures with hydrogen concentrations close to 18% vol. were used in the tests. The results from the numerical simulations are compared with the previous experimental data for the accuracy of the numerical model, and we have verified that the simulated overpressures and flame time-of-arrival data were in good agreement with the results of the previous two explosion tests.
Abstract: This study is aiming at establishing the relationship
between the optical signal of flame and an equivalent ratio of flame. In
this experiment, flame optical signal in a furnace is measured using
photodiode. The combustion system is composed of metal fiber burner
and vertical furnace, and flame chemiluminescence is measured at
various experimental conditions. In this study, the flame
chemiluminescence of laminar premixed flame is measured using
commercially available photodiode. It is experimentally investigated
the relationship between equivalent ratio and photodiode signal. In
addition, the strategy of combustion control method is proposed using
the optical signal and fuel pressure.
The results showed that certain relationship between optical data of
photodiode and equivalence ratio exists, and this leads to the
successful application of this system for instantaneous measurement of
equivalence ration of the combustion system.
Abstract: Palm methyl ester (PME) is one of the alternative
biomass fuels to liquid fossil fuels. To investigate the combustion
characteristics of PME as an alternative fuel for gas turbines, combustion experiments using two types of burners under atmospheric
pressure were performed. One of the burners has a configuration
making strong non-premixed flame, whereas the other has a
configuration promoting prevaporization of fuel droplets. The results
show that the NOx emissions can be reduced by employing the latter burner without accumulation of soot when PME is used as a fuel. A
burner configuration promoting prevaporzation of fuel droplets is
recommended for PME.
Abstract: The objective of this study is to investigate the
combustion in a pilot-ignited supercharged dual-fuel engine, fueled
with different types of gaseous fuels under various equivalence ratios.
It is found that if certain operating conditions are maintained,
conventional dual-fuel engine combustion mode can be transformed to
the combustion mode with the two-stage heat release. This mode of
combustion was called the PREMIER (PREmixed Mixture Ignition in
the End-gas Region) combustion. During PREMIER combustion,
initially, the combustion progresses as the premixed flame
propagation and then, due to the mixture autoignition in the end-gas
region, ahead of the propagating flame front, the transition occurs with
the rapid increase in the heat release rate.
Abstract: Cooktop burners are widely used nowadays. In
cooktop burner design, nozzle efficiency and greenhouse
gas(GHG) emissions mainly depend on heat transfer from the
premixed flame to the impinging surface. This is a complicated
issue depending on the individual and combined effects of various
input combustion variables. Optimal operating conditions for
sustainable burner design were rarely addressed, especially in the
case of multiple slot-jet burners. Through evaluating the optimal
combination of combustion conditions for a premixed slot-jet
array, this paper develops a practical approach for the sustainable
design of gas cooktop burners. Efficiency, CO and NOx emissions
in respect of an array of slot jets using premixed flames were
analysed. Response surface experimental design were applied to
three controllable factors of the combustion process, viz.
Reynolds number, equivalence ratio and jet-to-vessel distance.
Desirability Function Approach(DFA) is the analytic technique
used for the simultaneous optimization of the efficiency and
emission responses.
Abstract: Computational study of two dimensional supersonic reacting hydrogen-air flows is performed to investigate the nitrogen effects on ignition delay time for premixed and diffusion flames. Chemical reaction is treated using detail kinetics and the advection upstream splitting method is used to calculate the numerical inviscid fluxes. The results show that just in stoichiometric condition for both premixed and diffusion flames, there is monotone dependency of the ignition delay time to the nitrogen addition. In other situations, the optimal condition from ignition viewpoint should be found using numerical investigations.