Abstract: In this research, the effects of the engine parameters like compression ratios and steam injection on igniting timing and emission characteristics have been investigated numerically. The in-cylinder temperature and pressure at four different compression ratios have been compared with numerical results, and they show a good agreement with the published data. Two different fuels have been used in this study: Isooctane (IC8H18), and ethanol (C2H5OH). The increasing of the compression ratio (CR) advances the ignition timing, decreases the burn duration and increases the temperature and the pressure. The injection of water vapor lower than 40% decreased the peak temperature and slowed the combustion rate which leads to a lower NOx emission.
Abstract: Because of high thermal efficiency and low CO2
emission, diesel engines are being used widely in many industrial
fields although it makes many PM and NOx which give both human
health and environment a negative effect. NOx regulations for diesel
engines, however, are being strengthened and it is impossible to meet
the emission standard without NOx reduction devices such as SCR
(Selective Catalytic Reduction), LNC (Lean NOx Catalyst), and LNT
(Lean NOx Trap). Among the NOx reduction devices, urea-SCR
system is known as the most stable and efficient method to solve the
problem of NOx emission. But this device has some issues associated
with the ammonia slip phenomenon which is occurred by shortage of
evaporation and thermolysis time, and that makes it difficult to achieve
uniform distribution of the injected urea in front of monolith.
Therefore, this study has focused on the mixing enhancement between
urea and exhaust gases to enhance the efficiency of the SCR catalyst
equipped in catalytic muffler by changing inlet gas temperature and
spray conditions to improve the spray uniformity of the urea water
solution. Finally, it can be found that various parameters such as inlet
gas temperature and injector and injection angles significantly affect
the evaporation and mixing of the urea water solution with exhaust
gases, and therefore, optimization of these parameters are required.
Abstract: Palm methyl ester (PME) is one of the alternative
biomass fuels to liquid fossil fuels. To investigate the combustion
characteristics of PME as an alternative fuel for gas turbines, combustion experiments using two types of burners under atmospheric
pressure were performed. One of the burners has a configuration
making strong non-premixed flame, whereas the other has a
configuration promoting prevaporization of fuel droplets. The results
show that the NOx emissions can be reduced by employing the latter burner without accumulation of soot when PME is used as a fuel. A
burner configuration promoting prevaporzation of fuel droplets is
recommended for PME.
Abstract: Understanding of how and where NOx formation
occurs in industrial burner is very important for efficient and clean
operation of utility burners. Also the importance of this problem is
mainly due to its relation to the pollutants produced by more burners
used widely of gas turbine in thermal power plants and glass and steel
industry.
In this article, a numerical model of an industrial burner operating
in MILD combustion is validated with experimental data.. Then
influence of air flow rate and air temperature on combustor
temperature profiles and NOX product are investigated. In order to
modification this study reports on the effects of fuel and air dilution
(with inert gases H2O, CO2, N2), and also influence of lean-premixed
of fuel, on the temperature profiles and NOX emission.
Conservation equations of mass, momentum and energy, and
transport equations of species concentrations, turbulence, combustion
and radiation modeling in addition to NO modeling equations were
solved together to present temperature and NO distribution inside the
burner.
The results shows that dilution, cause to a reduction in value of
temperature and NOX emission, and suppresses any flame
propagation inside the furnace and made the flame inside the furnace
invisible. Dilution with H2O rather than N2 and CO2 decreases further
the value of the NOX. Also with raise of lean-premix level, local
temperature of burner and the value of NOX product are decreases
because of premixing prevents local “hot spots" within the combustor
volume that can lead to significant NOx formation. Also leanpremixing
of fuel with air cause to amount of air in reaction zone is
reach more than amount that supplied as is actually needed to burn
the fuel and this act lead to limiting NOx formation