Abstract: We report here structural, mechanical and I-V
characteristics of Zn1-xMxO ceramic samples with various x and M.
It is found that the considered dopants does not influence the wellknown
peaks related to wurtzite structure of ZnO ceramics, while the
shape and size of grains are clearly affected. Average crystalline
diameters, deduced from XRD are between 42 nm and 54 nm, which
are 70 times lower than those obtained from SEM micrographs.
Interestingly, the potential barrier could be formed by adding Cu up
to 0.20, and it is completely deformed by 0.025 Ni additions. The
breakdown field could be enhanced up to 4138 V/cm by 0.025 Cu
additions, followed by a decrease with further increase of Cu . On
the other hand a gradual decrease in VHN is reported for both
dopants and their values are higher in Ni samples as compared to Cu
samples. The electrical conductivity is generally improved by Ni,
while addition of Cu improved it only in the over doped region (≥
0.10). These results are discussed in terms of the difference of
valency and ferromagnetic ordering for both dopants as compared to
undoped sample.
Abstract: To investigate the production of cellulases from Aspergillus heteromorphus, submerged fermentation was performed using wheat straw as substrate. Optimization of saccharification conditions like pH, temperature and time were studied. Highest reducing sugar was released on 5th day at 5 pH, 30° C temperature. When A. heteromorphous was grown on wheat straw in submerged fermentation after 5 days incubation at 30 ° C, 3.2 IU/ml and 83 IU/ml, filter paper activity and CMCase activity respectively.
Abstract: Adjacent Hall microsensors, comprising a silicon
substrate and four contacts, providing simultaneously two supply inputs and two differential outputs, are characterized. The voltage
related sensitivity is in the order of 0.11T-1, and a cancellation method for offset compensation is used, achieving residual offset in
the micro scale which is also compared to a single Hall plate.
Abstract: Automatic tube current modulation (ATCM) systems are available for all CT manufacturers and are used for the majority of patients. Understanding how the systems work and their influence on patient dose and image quality is important for CT users, in order to gain the most effective use of the systems. In the present study, a new phantom was used for evaluating dose distribution and image quality under the ATCM operation for the Toshiba Aquilion 64 CT scanner using different ATCM options and a fixed mAs technique. A routine chest, abdomen and pelvis (CAP) protocol was selected for study and Gafchromic film was used to measure entrance surface dose (ESD), peripheral dose and central axis dose in the phantom. The results show the dose reductions achievable with various ATCM options, in relation with the target noise. The doses and image noise distribution were more uniform when the ATCM system was implemented compared with the fixed mAs technique. The lower limit set for the tube current will affect the modulations especially for the lower dose option. This limit prevented the tube current being reduced further and therefore the lower dose ATCM setting resembled a fixed mAs technique. Selection of a lower tube current limit is likely to reduce doses for smaller patients in scans of chest and neck regions.
Abstract: Biodiesel production results in glycerol production as
the main by-product in biodiesel industry.One of the utilizations of
glycerol obtained from biodiesel production is as a cement grinding
aid (CGA). Results showed that crude glycerol content was 40.19%
whereas pure glycerol content was 82.15%. BSS value of the cement
with CGA supplementation was higher than that of nonsupplemented
cement (blank) indicating that CGA-supplemented
cement had higher fineness than the non-supplemented one. It was
also found that pure glycerol 95% and TEA 5% at 80ºC was the
optimum CGA used to result in finest cement with BSS value of
4.836 cm2/g. Residue test showed that the smallest percent residue
value (0.11%) was obtained in cement with supplementation of pure
glycerol 95% and TEA 5%. Results of residue test confirmed those of
BSS test showing that cement with supplementation of pure glycerol
95% and TEA 5% had the finest particle size.
Abstract: The paper proposes the novel design of a 3T XOR gate combining complementary CMOS with pass transistor logic. The design has been compared with earlier proposed 4T and 6T XOR gates and a significant improvement in silicon area and power-delay product has been obtained. An eight transistor full adder has been designed using the proposed three-transistor XOR gate and its performance has been investigated using 0.15um and 0.35um technologies. Compared to the earlier designed 10 transistor full adder, the proposed adder shows a significant improvement in silicon area and power delay product. The whole simulation has been carried out using HSPICE.
Abstract: Text categorization techniques are widely used to many Information Retrieval (IR) applications. In this paper, we proposed a simple but efficient method that can automatically find the relationship between any pair of terms and documents, also an indexing matrix is established for text categorization. We call this method Indexing Matrix Categorization Machine (IMCM). Several experiments are conducted to show the efficiency and robust of our algorithm.
Abstract: This paper presented a proposed design for
transcutaneous inductive powering links. The design used to transfer
power and data to the implanted devices such as implanted
Microsystems to stimulate and monitoring the nerves and muscles.
The system operated with low band frequency 13.56 MHZ according
to industrial- scientific – medical (ISM) band to avoid the tissue
heating. For external part, the modulation index is 13 % and the
modulation rate 7.3% with data rate 1 Mbit/s assuming Tbit=1us. The
system has been designed using 0.35-μm fabricated CMOS
technology. The mathematical model is given and the design is
simulated using OrCAD P Spice 16.2 software tool and for real-time
simulation the electronic workbench MULISIM 11 has been used.
The novel circular plane (pancake) coils was simulated using
ANSOFT- HFss software.
Abstract: Developing a supply chain management (SCM) system is costly, but important. However, because of its complicated nature, not many of such projects are considered successful. Few research publications directly relate to key success factors (KSFs) for implementing a SCM system. Motivated by the above, this research proposes a hierarchy of KSFs for SCM system implementation in the semiconductor industry by using a two-step approach. First, the literature review indicates the initial hierarchy. The second step includes a focus group approach to finalize the proposed KSF hierarchy by extracting valuable experiences from executives and managers that actively participated in a project, which successfully establish a seamless SCM integration between the world's largest semiconductor foundry manufacturing company and the world's largest assembly and testing company. Future project executives may refer the resulting KSF hierarchy as a checklist for SCM system implementation in semiconductor or related industries.
Abstract: This paper investigates experimentally and
analytically the torsion behavior of steel fibered high strength self
compacting concrete beams reinforced by GFRP bars. Steel fibered
high strength self compacting concrete (SFHSSCC) and GFRP bars
became in the recent decades a very important materials in the
structural engineering field. The use of GFRP bars to replace steel
bars has emerged as one of the many techniques put forward to
enhance the corrosion resistance of reinforced concrete structures.
High strength concrete and GFRP bars attract designers and
architects as it allows improving the durability as well as the esthetics
of a construction. One of the trends in SFHSSCC structures is to
provide their ductile behavior and additional goal is to limit
development and propagation of macro-cracks in the body of
SFHSSCC elements. SFHSSCC and GFRP bars are tough, improve
the workability, enhance the corrosion resistance of reinforced
concrete structures, and demonstrate high residual strengths after
appearance of the first crack. Experimental studies were carried out
to select effective fiber contents. Three types of volume fraction from
hooked shape steel fibers are used in this study, the hooked steel
fibers were evaluated in volume fractions ranging between 0.0%,
0.75% and 1.5%. The beams shape is chosen to create the required
forces (i.e. torsion and bending moments simultaneously) on the test
zone. A total of seven beams were tested, classified into three groups.
All beams, have 200cm length, cross section of 10×20cm,
longitudinal bottom reinforcement of 3
Abstract: This paper presents the characterization and design of a capacitive pressure sensor with LC-based 0.35 µm CMOS readout circuit. SPICE is employed to evaluate the characteristics of the readout circuit and COMSOL multiphysics structural analysis is used to simulate the behavior of the pressure sensor. The readout circuit converts the capacitance variation of the pressure sensor into the frequency output. Simulation results show that the proposed pressure sensor has output frequency from 2.50 to 2.28 GHz in a pressure range from 0.1 to 2 MPa almost linearly. The sensitivity of the frequency shift with respect to the applied pressure load is 0.11 GHz/MPa.
Abstract: The essential oil of M. × piperita L. was formulated
into a topical gel. The prepared gel was characterized for its pH,
viscosity, spreadiblity, consistency and extrudiblity, while its stability
was evaluated under different temperature conditions. The prepared
M. × piperita oil gel was clear and transparent. The pH value of
developed gel was 6.6, while its viscosity was 1200 cP. Spreadability
and consistency of the M. × piperita oil gel was 10.7 g.cm/sec and 7
mm, respectively. The prepared gel showed good extrudiblity. During
the stability studies, no significant change in pH and viscosity as a
function of time for gel was observed, indicating stability of prepared
formulation. The gel developed in this study is expected to forward
the usage of M. × piperita essential towards commercial application.
Abstract: In this study, a robust intelligent backstepping tracking control (RIBTC) system combined with adaptive output recurrent cerebellar model articulation control (AORCMAC) and H∞ control technique is proposed for wheeled inverted pendulums (WIPs) real-time control with exact system dynamics unknown. Moreover, a robust H∞ controller is designed to attenuate the effect of the residual approximation errors and external disturbances with desired attenuation level. The experimental results indicate that the WIPs can stand upright stably when using the proposed RIBTC.
Abstract: The aim of this article is to narrate the utility of novel simulation approach i.e. convolution method to predict blood concentration of drug utilizing dissolution data of salbutamol sulphate microparticulate formulations with different release patterns (1:1, 1:2 and 1:3, drug:polymer). Dissolution apparatus II USP 2007 and 900 ml double distilled water stirrd at 50 rpm was employed for dissolution analysis. From dissolution data, blood drug concentration was determined, and in return predicted blood drug concentration data was used to calculate the pharmacokinetic parameters i.e. Cmax, Tmax, and AUC. Convolution is a good biwaiver technique; however its better utility needs it application in the conditions where biorelevant dissolution media are used.
Abstract: In this paper, we proposed the effects of Mo thickness
on the properties of AZO/Mo/AZO multilayer thin films for
opto-electronics applications. The structural, optical and electrical
properties of AZO/Mo/AZO thin films were investigated.
Optimization of the thin films coatings resulted with low resistivity of
9.98 × 10-5 )-cm, mobility of 12.75 cm2/V-s, carrier concentration of
1.05 × 1022 cm-3, maximum transmittance of 79.13% over visible
spectrum of 380 – 780 nm and Haacke figure of merit (FOM) are 5.95
× 10-2 )-1 under Mo layer thickness of 15 nm. These results indicate an
alternative candidate for use as a transparent electrode in solar cells
and various displays applications.
Abstract: Sunflower stalks were analysed for chemical
compositions: pentosan 15.84%, holocellulose 70.69%,
alphacellulose 45.74%, glucose 27.10% and xylose 7.69% based on
dry weight of 100-g raw material. The most optimum condition for
steam explosion pretreatment was as follows. Sunflower stalks were
cut into small pieces and soaked in 0.02 M H2SO4 for overnight.
After that, they were steam exploded at 207 C and 21 kg/cm2 for 3
minutes to fractionate cellulose, hemicellulose and lignin. The
resulting hydrolysate, containing hemicellulose, and cellulose pulp
contained xylose sugar at 2.53% and 7.00%, respectively.The pulp
was further subjected to enzymatic saccharification at 50 C, pH 4.8 citrate buffer) with pulp/buffer 6% (w/w)and Celluclast 1.5L/pulp
2.67% (w/w) to obtain single glucose with maximum yield 11.97%.
After fixed-bed fermentation under optimum condition using
conventional yeast mixtures to produce bioethanol, it indicated
maximum ethanol yield of 0.028 g/100 g sunflower stalk.
Abstract: Nowadays, manufacturers are facing great challenges
with regard to the production of green products due to the emerging issue of hazardous substance management (HSM). In particular,
environmental legislation pressures have yielded to increased risk,
manufacturing complexity and green components demands. The green principles were expanded to many departments within
organization, including supply chain. Green supply chain
management (GSCM) was emerging in the last few years. This idea
covers every stage in manufacturing from the first to the last stage of
life cycle. From product lifecycle concept, the cycle starts at the design of a product. QFD is a customer-driven product development
tool, considered as a structured management approach for efficiently
translating customer needs into design requirements and parts deployment, as well as manufacturing plans and controls in order to
achieve higher customer satisfaction. This paper develops an Eco-
QFD to provide a framework for designing Eco-mobile phone by integrating the life cycle analysis LCA into QFD throughout the entire product development process.
Abstract: A design flow of multi-standard down-conversion
CMOS mixers for three modern standards: Global System Mobile,
Digital Enhanced Cordless Telephone and Universal Mobile
Telecommunication Systems is presented. Three active mixer-s
structures are studied. The first is based on the Gilbert cell which
gives a tolerable noise figure and linearity with a low conversion
gain. The second and third structures use the current bleeding and
charge injection techniques in order to increase the conversion gain.
An improvement of about 2 dB of the conversion gain is achieved
without a considerable degradation of the other characteristics. The
models used for noise figure, conversion gain and IIP3 used are
studied. This study describes the nature of trade-offs inherent in such
structures and gives insights that help in identifying which structure
is better for given conditions.
Abstract: 115 samples of Labeo calbasu ranged 8.0-17.9cm
length with mean11.90±1.96 and 4.9-68.5g weight with mean
22.25±12.54 from the River Chenab, Southern Punjab, Pakistan were
analyzed to investigate length-weight relationships (LWR) of fish in
relation to condition factor (K). Standard length (SL), fork length
(FL), head length (HL) head width (HW), body girth (BG), dorsal fin
length (DFL), dorsal fin base (DFB), pectoral fin length (PcFL),
pelvic fin length (PvFL) and anal fin length (AFL) are found to be
highly correlated with increasing total length and wet body weight (r
> 0.500). Wet body weight has positive (r=0.540) and total length
has no correlation (r=0.344) with calculated Condition factor (K).
The slope “b" in the relationship is 3.27 and intercepts -2.2258.
Abstract: The paper presents the results of a series of
experiments conducted on physical models of Quarter-circle
breakwater (QBW) in a two dimensional monochromatic wave
flume. The purpose of the experiments was to evaluate the reflection
coefficient Kr of QBW models of different radii (R) for different
submergence ratios (d/hc), where d is the depth of water and hc is the
height of the breakwater crest from the sea bed. The radii of the
breakwater models studied were 20cm, 22.5cm, 25cm, 27.5cm and
submergence ratios used varied from 1.067 to 1.667. The wave
climate off the Mangalore coast was used for arriving at the various
model wave parameters. The incident wave heights (Hi) used in the
flume varied from 3 to 18cm, and wave periods (T) ranged from 1.2 s
to 2.2 s. The water depths (d) of 40cm, 45cm and 50cm were used in
the experiments. The data collected was analyzed to compute
variation of reflection coefficient Kr=Hr/Hi (where Hr=reflected wave
height) with the wave steepness Hi/gT2 for various R/Hi
(R=breakwater radius) values. It was found that the reflection
coefficient increased as incident wave steepness increased. Also as
wave height decreases reflection coefficient decreases and as
structure radius R increased Kr decreased slightly.