Abstract: The study of interaction among the grain, moisture,
and the surrounding space (air) is key to understanding the graindrying
process. In Iran, rice (mostly Indica type) is dried by flat
bed type dryer until the final MC reaches to 6 to 8%. The
experiments were conducted to examine the effect of application of
discharge fan with different heights of paddy on the drying
efficiency. Experiments were designed based on two different
configurations of the drying methods; with and without discharge
fan with three different heights of paddy including; 5, 10, and 15
cm. The humid heated air will be going out immediately by the
suction of discharge fan. The drying time is established upon the
average final MC to achieve about 8%. To save energy and reduce
the drying time, the distribution of temperature between layers
should be fast and uniform with minimum difference; otherwise
the difference of MC gradient between layers will be high and will
induce grain breakage. The difference of final MC between layers
in the two methods was 48-73%. The steady state of temperature
between the two methods has saved time in the range of 10-20%,
and the efficiency of temperature distribution increased 17-26% by
the use of discharge fan.
Abstract: The CMLP building was developed to be a model for
sustainability with strategies to reduce water, energy and pollution,
and to provide a healthy environment for the building occupants. The
aim of this paper is to investigate the environmental effects of energy
used by this building. A LCA (life cycle analysis) was led to measure
the real environmental effects produced by the use of energy. The
impact categories most affected by the energy use were found to be
the human health effects, as well as ecotoxicity. Natural gas
extraction, uranium milling for nuclear energy production, and the
blasting for mining and infrastructure construction are the processes
contributing the most to emissions in the human health effect. Data
comparing LCA results of CMLP building with a conventional
building results showed that energy used by the CMLP building has
less damage for the environment and human health than a
conventional building.
Abstract: The designing of charge pump with high gain Op-
Amp is a challenging task for getting faithful response .Design of
high performance phase locked loop require ,a design of high
performance charge pump .We have designed a operational amplifier
for reducing the error caused by high speed glitch in a transistor and
mismatch currents . A separate Op-Amp has designed in 180 nm
CMOS technology by CADENCE VIRTUOSO tool. This paper
describes the design of high performance charge pump for GHz
CMOS PLL targeting orthogonal frequency division multiplexing
(OFDM) application. A high speed low power consumption Op-Amp
with more than 500 MHz bandwidth has designed for increasing the
speed of charge pump in Phase locked loop.
Abstract: The purpose of this study was to analyze relationship
between gender, BMI, and lifestyle with bone mineral density
(BMD) of adolescent in urban areas . The place of this study in
Jakarta State University, Indonesia. The number of samples involved
as many as 200 people, consisting of 100 men and 100 women. BMD
was measured using Quantitative Ultrasound Bone Densitometry.
While the questionnaire used to collect data on age, gender, and
lifestyle (calcium intake, smoking habits, alcohol consumption, tea,
coffee, sports, and sun exposure). Mean age of men and women,
respectively as much as 20.7 ± 2.18 years and 21 ± 1.61 years. Mean
BMD values of men was 1.084 g/cm ² ± 0.11 while women was
0.976 g/cm ² ± 0.10. Men and women with normal BMD respectively
as much as 46.7% and 16.7%. Men and women affected by
osteopenia respectively as much as 50% and 80%. Men and women
affected by osteoporosis respectively as much as 3.3% and 3.3%.
Mean BMI of men and women, respectively as much as 21.4 ± 2.07
kg/m2 and 20.9 ± 2.06 kg/m2. Mean lifestyle score of men and
women , respectively as much as 71.9 ± 5.84 and 70.1 ± 5.67
(maximum score 100). Based on Spearman and Pearson Correlation
test, there were relationship significantly between gender and
lifestyle with BMD.
Abstract: In this study, the effect of greywater irrigation on airwater interfacial area is investigated. Several soil column experiments were conducted for different greywater irrigation to develop the pressure-saturation curves. Surface tension was measured for different greywater concentration and fitted for Gibbs adsorption equation. Pressure-saturation curves show that the reduction of capillary rise stops when it reaches its critical micelle concentration (CMC). A simple theory is derived from pressure-saturation curves for calculating air-water interfacial area in porous medium during greywater irrigation by introducing a term 'hydraulic radius' for the pores. This term diminishes any effect of pore shapes on the air-water interfacial area. The air-water interfacial area was calculated using the pressure-saturation curves and found that it decreases with increasing moisture content. But no significant effect was observed on air-water interfacial area for different greywater irrigation. A maximum of 10% variation in interfacial area was observed at the residual saturation zone.
Abstract: Copper sulfide nanoparticles (CuS) were successfully synthesized by the pulsed plasma in liquid method, using two copper rod electrodes submerged in molten sulfur. Low electrical energy and no high temperature were applied for synthesis. Obtained CuS nanoparticles were then analyzed by means of X-ray diffraction, Low and High Resolution Transmission Electron Microscopy, Electron Diffraction, X-ray Photoelectron, Raman Spectroscopies and Field Emission Scanning Electron Microscopy. XRD analysis revealed peaks for CuS with hexagonal phase composition. TEM and HRTEM studies showed that sizes of CuS nanoparticles ranged between 10-60 nm, with the average size of about 20 nm. Copper sulfide nanoparticles have short nanorod-like structure. Raman spectroscopy found peak for CuS at 474.2cm-1of Raman region.
Abstract: On the territory of France fenugreek is spread since long on a line from the Gironde to the Italian border. In Belarus experimental cultivation has begun since 2004. Experiments with fenugreek variety Ovari 4 were conducted about time of sowing in order to study their growth, development, and evaluation of productivity in the North-east part of Belarus and Central part of France. Reaching full ripeness of seeds the plants of fenugreek in the Central part of France requires about 94-97 days. Average seeds yield of 2011-2012 is 1259 kg/ha. Plant height is about 36,8 cm. Plants were affected by aphid and in the high moist agro-climatic conditions by powdery mildew. In North-east part of Belarus plants need 86-93 days to full ripeness. Plants of fenugreek have steam about 59 cm. The average seeds yield of 2007-2009 was about 723 kg/ha. Plants were resistant to aphid and diseases.
Abstract: An experiment was conducted on the comparative
study of drip and furrow irrigation methods at the farmer-s field in
Umar Kot. The total area under experiment about 4000m2 was
divided into two equal portions. One portion about 40m X 50m was
occupied by drip and the other portion about 40m X 50m by furrow
irrigation method. Soil at the experimental site was clay loam in
texture for 0-60cm depth; average dry bulk density and field capacity
was 1.16g/cm3 and 28.5% respectively. The results reveal that the
drip irrigation method saved 56.4% water and gave 22% more yield
as compared to that of furrow irrigation method. Higher water use
efficiency about 4.87 was obtained in drip irrigation method; whereas
lower water used efficiency about 1.66 was obtained in furrow
irrigation method. The present study suggests farming community to
adopt drip irrigation method instead of old traditional flooding
methods.
Abstract: An organic bulk heterojunction (BHJ) was fabricated using a blended film containing Copper (II) tetrakis(4-acumylphenoxy) phthalocyanine (Tc-CuPc) along with [6,6]-Phenyl C61 butyric acid methyl ester (PCBM). Weight ratio between Tc-CuPc and PCBM was 1:1. The electrical properties of Tc-CuPc: PCBM BHJ were examined. Rectifying nature of the BHJ was displayed by current-voltage (I-V) curves, recorded in dark and at various temperatures. At low voltages, conduction was ohmic succeeded by space-charge limiting current (SCLC) conduction at higher voltages in which exponential trap distribution was dominant. Series resistance, shunt resistance, ideality factor, effective barrier height and mobility at room temperature were found to be 526 4, 482 k4, 3.7, 0.17 eV and 2×10-7 cm2V-1s-1 respectively. Temperature effect towards different BHJ parameters was observed under dark condition.
Abstract: Air bubbles have been detected in human circulation
of end-stage renal disease patients who are treated by hemodialysis.
The consequence of air embolism, air bubbles, is under recognized
and usually overlooked in daily practice. This paper shows results of
a capacitor based detection method that capable of detecting the
presence of air bubbles in the blood stream in different frequencies.
The method is based on a parallel plates capacitor made of platinum
with an area of 1.5 cm2 and a distance between the two plates is 1cm.
The dielectric material used in this capacitor is Dextran70 solution
which mimics blood rheology. Simulations were carried out using
RC circuit at two frequencies 30Hz and 3 kHz and results compared
with experiments and theory. It is observed that by injecting air
bubbles of different diameters into the device, there were significant
changes in the capacitance of the capacitor. Furthermore, it is
observed that the output voltage from the circuit increased with
increasing air bubble diameter. These results demonstrate the
feasibility of this approach in improving air bubble detection in
Hemodialysis.
Abstract: The effect of the number of quantum dot (QD) layers
on the saturated gain of doped QD semiconductor optical amplifiers
(SOAs) has been studied using multi-population coupled rate
equations. The developed model takes into account the effect of
carrier coupling between adjacent layers. It has been found that
increasing the number of QD layers (K) increases the unsaturated
optical gain for K
Abstract: Behavior of turbulent jet is relying on jet parameters,
environmental and geometric parameters. In this research, it has
attempt to Study effect of jet parameters of internal angle on
maximum effective length and velocity on centerline from nozzle
experimentally. Toward this end, four internal angles 30, 45, 60 and
90-degree are considered for this study in a flume with 600cm as
long, 100cm as high and 150cm in width. Various discharges were
used to evaluate effective length for a wide range of densimetric
Froude numbers F0, from 17.9 to 39.4 that is defined at the nozzle. As
a result, It is revealed that both velocity on centerline and effective
length decreases when nozzle angle decreased from 90° to 30°. The
results show that, for all range of Fr0 the Um/U0 ratio for nozzle with
α=90° on centerline increases 20% - 27% than nozzle with α=30° that
has lowest velocity on centerline than other nozzle.
Abstract: A 2.4GHz (RF) down conversion Gilbert Cell mixer,
implemented in a 0.18-μm CMOS technology with a 1.8V supply, is
presented. Current bleeding (charge injection) technique has been
used to increase the conversion gain and the linearity of the mixer.
The proposed mixer provides 10.75 dB conversion gain ( C G ) with
14.3mw total power consumption. The IIP3 and 1-dB compression
point of the mixer are 8dbm and -4.6dbm respectively, at 300 MHz
IF frequencies. Comparing the current design against the
conventional mixer design, demonstrates better performance in the
conversion gain, linearity, noise figure and port-to-port isolation.
Abstract: In this paper, we argue the security protocols of
ZigBee wireless sensor network in MAC layer. AES 128-bit
encryption algorithm in CCM* mode is secure transferred data;
however, AES-s secret key will be break within nearest future.
Efficient public key algorithm, ECC has been mixed with AES to
rescue the ZigBee wireless sensor from cipher text and replay attack.
Also, the proposed protocol can parallelize the integrity function to
increase system performance.
Abstract: The effect of wood vinegar, entomopathogenic
nematodes ((Steinernema thailandensis n. sp.) and fermented organic
substances from four plants such as: Derris elliptica Roxb, Stemona
tuberosa Lour, Tinospora crispa Mier and Azadirachta indica J. were
tested on the five varieties of sweetpotato with potential for
bioethanol production ie. Taiwan, China, PROC No.65-16, Phichit
166-5, and Phichit 129-6. The experimental plots were located at
Faculty of Agriculture, Natural Resources and Environment,
Naresuan University, Phitsanulok, Thailand. The aim of this study
was to compare the efficiency of the five treatments for growth, yield
and insect infestation on the five varieties of sweetpotato. Treatment
with entomopathogenic nematodes gave the highest average weight
of sweetpotato tubers (1.3 kg/tuber), followed by wood vinegar,
fermented organic substances and mixed treatment with yields of
0.88, 0.46 and 0.43 kg/tuber, respectively. Also the
entomopathogenic nematode treatment gave significantly higher
average width and length of sweet potato (9.82 cm and 9.45 cm,
respectively). Additionally, the entomopathogenic nematode
provided the best control of insect infestation on sweetpotato leaves
and tubers. Comparison among the varieties of sweetpotato, PROC
NO.65-16 showed the highest weight and length. However, Phichit
129-6 gave significantly higher weight of 0.94 kg/tuber. Lastly, the
lowest sweet potato weevil infestation on leaves and tubers occurred
on Taiwan and Phichit 129-6.
Abstract: In unsupervised segmentation context, we propose a bi-dimensional hidden Markov chain model (X,Y) that we adapt to the image segmentation problem. The bi-dimensional observed process Y = (Y 1, Y 2) is such that Y 1 represents the noisy image and Y 2 represents a noisy supplementary information on the image, for example a noisy proportion of pixels of the same type in a neighborhood of the current pixel. The proposed model can be seen as a competitive alternative to the Hilbert-Peano scan. We propose a bayesian algorithm to estimate parameters of the considered model. The performance of this algorithm is globally favorable, compared to the bi-dimensional EM algorithm through numerical and visual data.
Abstract: Using plug flow model in conjunction with
experimental solute concentration profiles, overall volumetric mass
transfer coefficient based on continuous phase (Koca), in a packed
liquid-liquid extraction column has been optimized. Number of 12
experiments has been done using standard system of water/acid
acetic/toluene in a 6 cm diameter, 120 cm height column. Thorough
consideration of influencing parameters we intended to correlate
dimensionless parameters in term of overall Sherwood number which
has an acceptable average error of about 15.8%.
Abstract: The present work deals with the calculation of
transport properties of Hg0.8Cd0.2Te (MCT) semiconductor in
degenerate case. Due to their energy-band structure, this material
becomes degenerate at moderate doping densities, which are around
1015 cm-3, so that the usual Maxwell-Boltzmann approximation is
inaccurate in the determination of transport parameters. This problem
is faced by using Fermi-Dirac (F-D) statistics, and the non-parabolic
behavior of the bands may be approximated by the Kane model. The
Monte Carlo (MC) simulation is used here to determinate transport
parameters: drift velocity, mean energy and drift mobility versus
electric field and the doped densities. The obtained results are in
good agreement with those extracted from literature.
Abstract: The recycling process of Tungsten alloy (Swarf) by
oxidation reduction technique have been investigated. The reduced
powder was pressed under a pressure 20Kg/cm2 and sintered at
1150°C in dry hydrogen atmosphere. The particle size of the recycled
alloy powder was 1-3 μm and the shape was regular at a reduction
temperature 800°C. The chemical composition of the recycled alloy
is the same as the primary Swarf.
Abstract: The performance of mortar subjected to high
temperature and cooled in normal ambient temperature was examined
in the laboratory to comply with the situation of burning & cooling of
a structure. Four series of cubical (5 X 5 X 5 cm) mortar specimens
were made from OPC, and partial replacement (10, 15, 20, 25 &
30%) of OPC by Rice Husk Ash (RHA) produced in the uncontrolled
environment. These specimens were heated in electric furnace to 200,
300, 400, 500 and 7000C. The specimens were kept in normal room
temperature for cooling. They were then tested for mechanical
properties and the results shows that particular 20% RHA mixed
mortar shows better fire performance.