Abstract: We investigate relaxation dynamics of a quantum
dipole emitter (QDE), e.g., a molecule or quantum dot, located near a
metal nanoparticle (MNP) exhibiting a dipolar localized surface
plasmon (LSP) resonance at the frequency of the QDE radiative
transition. It is shown that under the condition of the QDE-MNP
characteristic relaxation time being much shorter than that of the
QDE in free-space but much longer than the LSP lifetime. It is also
shown that energy dissipation in the QDE-MNP system is relatively
weak with the probability of the photon emission being about 0.75, a
number which, rather surprisingly, does not explicitly depend on the
metal absorption characteristics. The degree of entanglement
measured by the concurrency takes the maximum value, while the
distances between the QDEs and metal ball approximately are equal.
Abstract: Early diagnosis of infection like Hep-B virus in blood
is important for low cost medical treatment. For this purpose, it is
desirable to develop a point of care device which should be able to
detect trace quantities of the target molecule in blood. In this paper,
we report a nanoporous silicon oxide sensor which is capable of
detecting down to 1fM concentration of Hep-B surface antigen in
blood without the requirement of any centrifuge or pre-concentration.
This has been made possible by the presence of resonant peak in the
sensitivity characteristics. This peak is observed to be dependent only
on the concentration of the specific antigen and not on the interfering
species in blood serum. The occurrence of opposite impedance
change within the pores and at the bottom of the pore is responsible
for this effect. An electronic interface has also been designed to
provide a display of the virus concentration.
Abstract: Propylene self-metathesis to ethylene and butene was
studied over WOx/SiO2 catalysts at 450oC and atmospheric pressure.
The WOx/SiO2 catalysts were prepared by incipient wetness
impregnation of ammonium metatungstate aqueous solution. It was
found that, adding nano-sized extra supports (SiO2 and TiO2) by
physical mixing with the WOx/SiO2 enhanced propylene conversion.
The UV-Vis and FT-Raman results revealed that WOx could migrate
from the original silica support to the extra support, leading to a
better dispersion of WOx. The ICP-OES results also indicate that
WOx existed on the extra support. Coke formation was investigated
on the catalysts after 10 h time-on-stream by TPO. However, adding
nano-sized extra supports led to higher coke formation which may be
related to acidity as characterized by NH3-TPD.
Abstract: This paper presents the design and fabrication of an
optical window for an optical modulator toward image sensing
applications. An optical window consists of micrometer-order SiO2
capillaries (porous solid) that can modulate transmission light
intensity by moving the liquid in and out of porous solid. A high
optical transmittance of the optical window can be achieved due to
refractive index matching when the liquid is penetrated into the
porous solid. Otherwise, its light transmittance is lower because of
light reflection and scattering by air holes and capillary walls. Silicon
capillaries fabricated by deep reactive ion etching (DRIE) process are
completely oxidized to form the SiO2 capillaries. Therefore, high
aspect ratio SiO2 capillaries can be achieved based on silicon
capillaries formed by DRIE technique. Large compressive stress of
the oxide causes bending of the capillary structure, which is reduced
by optimizing the design of device structure. The large stress of the
optical window can be released via thin supporting beams. A 7.2 mm
x 9.6 mm optical window area toward a fully integrated with the
image sensor format is successfully fabricated and its optical
transmittance is evaluated with and without inserting liquids (ethanol
and matching oil). The achieved modulation range is approximately
20% to 35% with and without liquid penetration in visible region
(wavelength range from 450 nm to 650 nm).
Abstract: A cyclostationary Gaussian linearization method is
formulated for investigating the time average response of nonlinear
system under sinusoidal signal and white noise excitation. The
quantitative measure of cyclostationary mean, variance, spectrum of
mean amplitude, and mean power spectral density of noise are
analyzed. The qualitative response behavior of stochastic jump and
bifurcation are investigated. The validity of the present approach in
predicting the quantitative and qualitative statistical responses is
supported by utilizing Monte Carlo simulations. The present analysis
without imposing restrictive analytical conditions can be directly
derived by solving non-linear algebraic equations. The analytical
solution gives reliable quantitative and qualitative prediction of mean
and noise response for the Duffing system subjected to both sinusoidal
signal and white noise excitation.
Abstract: This paper presents a model for a modified T-junction
device for microspheres generation. The numerical model is
developed using a commercial software package: COMSOL
Multiphysics. In order to test the accuracy of the numerical model,
multiple variables, such as the flow rate of cross-flow, fluid properties,
structure, and geometry of the microdevice are applied. The results
from the model are compared with the experimental results in the
diameter of the microsphere generated. The comparison shows a good
agreement. Therefore the model is useful in further optimization of the
device and feedback control of microsphere generation if any.
Abstract: The capability of exploiting the electronic charge and
spin properties simultaneously in a single material has made diluted
magnetic semiconductors (DMS) remarkable in the field of
spintronics. We report the designing of DMS based on zinc-blend
ZnO doped with Cr impurity. The full potential linearized augmented
plane wave plus local orbital FP-L(APW+lo) method in density
functional theory (DFT) has been adapted to carry out these
investigations. For treatment of exchange and correlation energy,
generalized gradient approximations have been used. Introducing Cr
atoms in the matrix of ZnO has induced strong magnetic moment
with ferromagnetic ordering at stable ground state. Cr:ZnO was found
to favor the short range magnetic interaction that
reflect tendency of Cr clustering. The electronic structure of ZnO is
strongly influenced in the presence of Cr impurity atoms where
impurity bands appear in the band gap.
Abstract: Although, lanthanum carbonate has not been approved
by the FDA for treatment of hyperphosphatemia, we prospectively
evaluated the efficacy of the combination of Calcium hydroxyapatite
(CHAp) and Lanthanum Carbonate (LaC) for the treatment of
hyperphosphatemia on mice. CHAp was prepared by co-precipitation
method using Ca(OH)2, H3PO4, NH4OH with calcination at 1200ºC.
Lanthanum carbonate was prepared by chemical method using
NaHCO3 and LaCl3 at low pH environment, below 4.0. The
structures were characterized by FTIR spectra and SEM -EDX
analysis. The study group included 16 subjects-mice divided into four
groups according to the administered substance: lanthanum carbonate
(group A), CHAp (group B), lanthanum carbonate + CHAp (group C)
and salt water (group D). The results indicate a phosphate decrease
when subjects (mice) were treated with CHAp and lanthanum
carbonate (0.5% CMC), in a single dose of 1500 mg/kg. Serum
phosphate concentration decreased [(from 4.5 ± 0.8 mg/dL) to
4.05 ± 0.2 mg/dL), P < 0.01] in group A and in group C (to 3.6
± 0.2 mg/dL) at 12 hours from the administration. The combination
of CHAp and lanthanum carbonate is a suitable regimen for
hyperphosphatemia treatment because it avoids both the
hypercalcemia of CaCO3 and the adverse effects of CHAp.
Abstract: This study investigates the suitability of using plastic,
such as polyethylene terephthalate (PET), as a partial replacement of
natural coarse and fine aggregates (for example, brick chips and
natural sand) to produce lightweight concrete for load bearing
structural members. The plastic coarse aggregate (PCA) and plastic
fine aggregate (PFA) were produced from melted polyethylene
terephthalate (PET) bottles. Tests were conducted using three
different water–cement (w/c) ratios, such as 0.42, 0.48, and 0.57,
where PCA and PFA were used as 50% replacement of coarse and
fine aggregate respectively. Fresh and hardened properties of
concrete have been compared for natural aggregate concrete (NAC),
PCA concrete (PCC) and PFA concrete (PFC). The compressive
strength of concrete at 28 days varied with the water–cement ratio for
both the PCC and PFC. Between PCC and PFC, PFA concrete
showed the highest compressive strength (23.7 MPa) at 0.42 w/c ratio
and also the lowest compressive strength (13.7 MPa) at 0.57 w/c
ratio. Significant reduction in concrete density was mostly observed
for PCC samples, ranging between 1977–1924 kg/m³. With the
increase in water–cement ratio PCC achieved higher workability
compare to both NAC and PFC. It was found that both the PCA and
PFA contained concrete achieved the required compressive strength
to be used for structural purpose as partial replacement of the natural
aggregate; but to obtain the desired lower density as lightweight
concrete the PCA is most suited.
Abstract: The quality and condition of perishable products
delivered to the market and their subsequent selling prices are
directly affected by the care taken during harvesting and handling.
Mechanical injury, in fact, occurs at all stages, from pre-harvest
operations through post-harvest handling, packing and transport to
the market. The main implications of this damage are the reduction of
the product’s quality and economical losses related to the shelf life
diminution. For most perishable products, the shelf life is relatively
short and it is typically dictated by microbial growth related to the
application of dynamic and static loads during transportation. This
paper presents the correlation between vibration levels and
microbiological growth on strawberries and woodland strawberries
and detects the presence of volatile organic compounds (VOC) in
order to develop an intelligent logistic unit capable of monitoring
VOCs using a specific sensor system. Fresh fruits were exposed to
vibrations by means of a vibrating table in a temperature-controlled
environment. Microbiological analyses were conducted on samples,
taken at different positions along the column of the crates. The values
obtained were compared with control samples not exposed to
vibrations and the results show that different positions along the
column influence the development of bacteria, yeasts and filamentous
fungi.
Abstract: All the software engineering researches and best
industry practices aim at providing software products with high
degree of quality and functionality at low cost and less time. These
requirements are addressed by the Component Based Software
Engineering (CBSE) as well. CBSE, which deals with the software
construction by components’ assembly, is a revolutionary extension
of Software Engineering. CBSE must define and describe processes
to assure timely completion of high quality software systems that are
composed of a variety of pre built software components. Though
these features provide distinct and visible benefits in software design
and programming, they also raise some challenging problems. The
aim of this work is to summarize the pertinent issues and
considerations in CBSE to make an understanding in forms of
concepts and observations that may lead to development of newer
ways of dealing with the problems and challenges in CBSE.
Abstract: The purposes of this study are 1) to study the effects
of participatory error correction process and 2) to find out the
students’ satisfaction of such error correction process. This study is a
Quasi Experimental Research with single group, in which data is
collected 5 times preceding and following 4 experimental studies of
participatory error correction process including providing coded
indirect corrective feedback in the students’ texts with error treatment
activities. Samples include 52 2nd year English Major students,
Faculty of Humanities and Social Sciences, Suan Sunandha Rajabhat
University. Tool for experimental study includes the lesson plan of
the course; Reading and Writing English for Academic Purposes II,
and tools for data collection include 5 writing tests of short texts and
a questionnaire. Based on formative evaluation of the students’
writing ability prior to and after each of the 4 experiments, the
research findings disclose the students’ higher scores with statistical
difference at 0.00. Moreover, in terms of the effect size of such
process, it is found that for mean of the students’ scores prior to and
after the 4 experiments; d equals 0.6801, 0.5093, 0.5071, and 0.5296
respectively. It can be concluded that participatory error correction
process enables all of the students to learn equally well and there is
improvement in their ability to write short texts. Finally the students’
overall satisfaction of the participatory error correction process is in
high level (Mean = 4.39, S.D. = 0.76).
Abstract: Alone with fast urbanization in world, traffic control
became a big issue in urban construction. Having an efficient and
reliable traffic control system is crucial to macro-traffic control.
Traffic signal is used to manage conflicting requirement by allocating
different sets of mutually compatible traffic movement during distinct
time interval. Many approaches have been made proposed to solve
this discrete stochastic problem. Recognizing the need to minimize
right-of-way impacts while efficiently handling the anticipated high
traffic volumes, the proposed alternative system gives effective
design. This model allows for increased traffic capacity and reduces
delays by eliminating a step in maneuvering through the freeway
interchange. The concept proposed in this paper involves
construction of bridges and ramps at intersection of four roads to
control the vehicular congestion and to prevent traffic breakdown.
Abstract: Microalgae Meyerella planktonica is a potential
biofuel source because it can grow in bulk in either autotrophic or
heterotrophic condition. However, the quantitative growth of this
algal type is still low as it tends to precipitates on the bottom.
Besides, the lipid concentration is still low when grown in
autotrophic condition. In contrast, heterotrophic condition can
enhance the lipid concentration. The combination of autotrophic
condition and agitation treatment was conducted to increase the
density of the culture. On the other hand, a heterotrophic condition
was set up to raise the lipid production. A two-stage experiment
was applied to increase the density at the first step and to increase
the lipid concentration in the next step. The autotrophic condition
resulted higher density but lower lipid concentration compared to
heterotrophic one. The agitation treatment produced higher density
in both autotrophic and heterotrophic conditions. The two-stage
experiment managed to enhance the density during the autotrophic
stage and the lipid concentration during the heterotrophic stage.
The highest yield was performed by using 0.4% v/v glycerol as a
carbon source (2.9±0.016 x 10^6 cells w/w) attained 7 days after the
heterotrophic stage began. The lipid concentration was stable
starting from day 7.
Abstract: In this article, the antibiogram and heavy metal
resistance profile of the bacteria isolated from total 34 studied
animals (Pelophylax ridibundus = 12; Mauremys rivulata = 14;
Natrix natrix = 8) captured around the Biga Stream, are described.
There was no database information on antibiogram and heavy metal
resistance profile of bacteria from these area’s amphibians and
reptiles.
A total of 200 bacteria were successfully isolated from cloaca and
oral samples of the aquatic amphibians and reptiles as well as from
the water sample. According to Jaccard’s similarity index, the degree
of similarity in the bacterial flora was quite high among the
amphibian and reptile species under examination, whereas it was
different from the bacterial diversity in the water sample. The most
frequent isolates were A. hydrophila (31.5%), B. pseudomallei
(8.5%), and C. freundii (7%). The total numbers of bacteria obtained
were as follows: 45 in P. ridibundus, 45 in N. natrix 30 in M.
rivulata, and 80 in the water sample. The result showed that
cefmetazole was the most effective antibiotic to control the bacteria
isolated in this study and that approximately 93.33% of the bacterial
isolates were sensitive to this antibiotic. The multiple antibiotic
resistances (MAR) index indicated that P. ridibundus (0.95) > N.
natrix (0.89) > M. rivulata (0.39). Furthermore, all the tested heavy
metals (Pb+2, Cu+2, Cr+3, and Mn+2) inhibit the growth of the bacterial
isolates at different rates. Therefore, it indicated that the water source
of the animals was contaminated with both antibiotic residues and
heavy metals.
Abstract: In our research we aimed to test a managerial
approach for the fuzzy front end (FFE) of innovation by creating
controlled experiment/ business case in a breakthrough innovation
development. The experiment was in the sport industry and covered
all aspects of the customer discovery stage from ideation to
prototyping followed by patent application. In the paper we describe
and analyze mile stones, tasks, management challenges, decisions
made to create the break through innovation, evaluate overall
managerial efficiency that was at the considered FFE stage.
We set managerial outcome of the FFE stage as a valid product
concept in hand. In our paper we introduce hypothetical construct
“Q-factor” that helps us in the experiment to distinguish quality of
FFE outcomes.
The experiment simulated for entrepreneur the FFE of innovation
and put on his shoulders responsibility for the outcome of valid
product concept. While developing managerial approach to reach the
outcome there was a decision to look on product concept from the
cognitive psychology and cognitive science point of view. This view
helped us to develop the profile of a person whose projection (mental
representation) of a new product could optimize for a manager or
entrepreneur FFE activities. In the experiment this profile was tested
to develop breakthrough innovation for swimmers. Following the
managerial approach the product concept was created to help
swimmers to feel/sense water. The working prototype was developed
to estimate the product concept validity and value added effect for
customers.
Based on feedback from coachers and swimmers there were strong
positive effect that gave high value for customers, and for the
experiment – the valid product concept being developed by proposed
managerial approach for the FFE.
In conclusions there is a suggestion of managerial approach that
was derived from experiment.
Abstract: Typically, virtual communities exhibit the well-known
phenomenon of participation inequality, which means that only a
small percentage of users is responsible of the majority of
contributions. However, the sustainability of the community requires
that the group of active users must be continuously nurtured with new
users that gain expertise through a participation process. This paper
analyzes the time evolution of Open Source Software (OSS)
communities, considering users that join/abandon the community
over time and several topological properties of the network when
modeled as a social network. More specifically, the paper analyzes
the role of those users rejoining the community and their influence in
the global characteristics of the network.
Abstract: Subspace channel estimation methods have been
studied widely, where the subspace of the covariance matrix is
decomposed to separate the signal subspace from noise subspace. The
decomposition is normally done by using either the eigenvalue
decomposition (EVD) or the singular value decomposition (SVD) of
the auto-correlation matrix (ACM). However, the subspace
decomposition process is computationally expensive. This paper
considers the estimation of the multipath slow frequency hopping
(FH) channel using noise space based method. In particular, an
efficient method is proposed to estimate the multipath time delays by
applying multiple signal classification (MUSIC) algorithm which is
based on the null space extracted by the rank revealing LU (RRLU)
factorization. As a result, precise information is provided by the
RRLU about the numerical null space and the rank, (i.e., important
tool in linear algebra). The simulation results demonstrate the
effectiveness of the proposed novel method by approximately
decreasing the computational complexity to the half as compared
with RRQR methods keeping the same performance.
Abstract: Exact solution of an unsteady MHD flow of elasticoviscous
fluid through a porous media in a tube of spherical cross
section under the influence of magnetic field and constant pressure
gradient has been obtained in this paper. Initially, the flow is
generated by a constant pressure gradient. After attaining the steady
state, the pressure gradient is suddenly withdrawn and the resulting
fluid motion in a tube of spherical cross section by taking into
account of the porosity factor and magnetic parameter of the
bounding surface is investigated. The problem is solved in two-stages
the first stage is a steady motion in tube under the influence of a
constant pressure gradient, the second stage concern with an unsteady
motion. The problem is solved employing separation of variables
technique. The results are expressed in terms of a non-dimensional
porosity parameter (K), magnetic parameter (m) and elasticoviscosity
parameter (β), which depends on the Non-Newtonian
coefficient. The flow parameters are found to be identical with that of
Newtonian case as elastic-viscosity parameter and magnetic
parameter tends to zero and porosity tends to infinity. It is seen that
the effect of elastico-viscosity parameter, porosity parameter and
magnetic parameter of the bounding surface has significant effect on
the velocity parameter.
Abstract: The material selection in the design of the sandwich
structures is very crucial aspect because of the positive or negative
influences of the base materials to the mechanical properties of the
entire panel. In the literature, it was presented that the selection of the
skin and core materials plays very important role on the behavior of
the sandwich. Beside this, the use of the correct adhesive can make
the whole structure to show better mechanical results and behavior.
In the present work, the static three-point bending tests were
performed on the sandwiches having an aluminum alloy foam core,
the skins made of three different types of fabrics and two different
commercial adhesives (flexible polyurethane and toughened epoxy
based) at different values of support span distances by aiming the
analyses of their flexural performance in terms of absorbed energy,
peak force values and collapse mechanisms. The main results of the
flexural loading are: force-displacement curves obtained after the
bending tests, peak force and absorbed energy values, collapse
mechanisms and adhesion quality. The experimental results presented
that the sandwiches with epoxy based toughened adhesive and the
skins made of S-Glass Woven fabrics indicated the best adhesion
quality and mechanical properties. The sandwiches with toughened
adhesive exhibited higher peak force and energy absorption values
compared to the sandwiches with flexible adhesive. The use of these
sandwich structures can lead to a weight reduction of the transport
vehicles, providing an adequate structural strength under operating
conditions.