Abstract: A numerical simulation of vortex-induced vibration of
a 2-dimensional elastic circular cylinder with two degree of freedom
under the uniform flow is calculated when Reynolds is 200.
2-dimensional incompressible Navier-Stokes equations are solved
with the space-time finite element method, the equation of the cylinder
motion is solved with the new explicit integral method and the mesh
renew is achieved by the spring moving mesh technology. Considering
vortex-induced vibration with the low reduced damping parameter, the
variety trends of the lift coefficient, the drag coefficient, the
displacement of cylinder are analyzed under different oscillating
frequencies of cylinder. The phenomena of locked-in, beat and
phases-witch were captured successfully. The evolution of vortex
shedding from the cylinder with time is discussed. There are very
similar trends in characteristics between the results of the one degree
of freedom cylinder model and that of the two degree of freedom
cylinder model. The streamwise vibrations have a certain effect on the
lateral vibrations and their characteristics.
Abstract: TiO2 nanoparticles were synthesized by hydrothermal
method at 180°C from TiOSO4 aqueous solution with1m/l
concentration. The obtained products were coated with silica by
means of a seeded polymerization technique for a coating time of
1440 minutes to obtain well defined TiO2@SiO2 core-shell structure.
The uncoated and coated nanoparticles were characterized by using
X-Ray diffraction technique (XRD), Fourier Transform Infrared
Spectroscopy (FT-IR) to study their physico-chemical properties.
Evidence from XRD and FTIR results show that SiO2 is
homogenously coated on the surface of titania particles. FTIR spectra
show that there exists an interaction between TiO2 and SiO2 and
results in the formation of Ti-O-Si chemical bonds at the interface of
TiO2 particles and SiO2 coating layer. The non linear optical limiting
properties of TiO2 and TiO2@SiO2 nanoparticles dispersed in
ethylene glycol were studied at 532nm using 5ns Nd:YAG laser
pulses. Three-photon absorption is responsible for optical limiting
characteristics in these nanoparticles and it is seen that the optical
nonlinearity is enhanced in core-shell structures when compared with
single counterparts. This effective three-photon type absorption at
this wavelength, is of potential application in fabricating optical
limiting devices.
Abstract: A analysis on the conventional the blood pressure estimation method using an oscillometric sphygmomanometer was
performed through a computer simulation using an arterial pressure-volume (APV) model. Traditionally, the maximum amplitude algorithm (MAP) was applied on the oscillation waveforms of the APV model to obtain the mean arterial pressure and the characteristic ratio. The estimation of mean arterial pressure and
characteristic ratio was significantly affected with the shape of the blood pressure waveforms and the cutoff frequency of high-pass filter
(HPL) circuitry. Experimental errors are due to these effects when estimating blood pressure. To find out an algorithm independent from
the influence of waveform shapes and parameters of HPL, the volume
oscillation of the APV model and the phase shift of the oscillation with fast fourier transform (FFT) were testified while increasing the cuff
pressure from 1 mmHg to 200 mmHg (1 mmHg per second). The phase shift between the ranges of volume oscillation was then only observed between the systolic and the diastolic blood pressures. The same results were also obtained from the simulations performed on two different the arterial blood pressure waveforms and one
hyperthermia waveform.
Abstract: Supersonic open and closed cavity flows are investigated experimentally and computationally. Free stream Mach number of two is set. Schlieren imaging is used to visualise the flow behaviour showing stark differences between open and closed. Computational Fluid Dynamics (CFD) is used to simulate open cavity of flow with aspect ratio of 4. A rear wall treatment is implemented in order to pursue a simple passive control approach. Good qualitative agreement is achieved between the experimental flow visualisation and the CFD in terms of the expansion-shock waves system. The cavity oscillations are shown to be dominated by the first and third Rossister modes combining to high fluctuations of non-linear nature above the cavity rear edge. A simple rear wall treatment in terms of a hole shows mixed effect on the flow oscillations, RMS contours, and time history density fluctuations are given and analysed.
Abstract: There are various kinds of medical equipment which
requires relatively accurate positional adjustments for successful
treatment. However, patients tend to move without notice during a
certain span of operations. Therefore, it is common practice that
accompanying operators adjust the focus of the equipment. In this
paper, tracking controllers for medical equipment are suggested to
replace the operators. The tracking controllers use AHRS sensor
information to recognize the movements of patients. Sensor fusion is
applied to reducing the error magnitudes through linear Kalman filters.
The image processing of optical markers is included to adjust the
accumulation errors of gyroscope sensor data especially for yaw
angles.
The tracking controller reduces the positional errors between the
current focus of a device and the target position on the body of a
patient. Since the sensing frequencies of AHRS sensors are very high
compared to the physical movements, the control performance is
satisfactory. The typical applications are, for example, ESWT or
rTMS, which have the error ranges of a few centimeters.
Abstract: This paper investigates the influence of various
parameters on the behaviour of water droplets on polymeric surfaces
under high electric fields. An inclined plane test was carried out to
understand the droplet behaviour in strong electric field. Parameters
such as water droplet conductivity, droplet volume, polymeric
surface roughness and droplet positioning with respect to the
electrodes were studied. The flashover voltage is affected by all
aforementioned parameters. The droplet positioning is in some cases
more vital than the droplet volume. Surface damages were analysed
using Scanning Electron Microscopy (SEM) studies and by Energy
dispersive X-ray Analysis (EDAX). It is observes that magnitude of
discharge have direct influence on amount of surface da
Abstract: The paper is included within the framework of a
complex research program, which was initiated from the hypothesis
arguing on the existence of a correlation between pineal indolic and
peptide hormones and the somatic development rhythm, including
thus the epithalamium-epiphysis complex involvement. At birds,
pineal gland contains a circadian oscillator, playing a main role in the
temporal organization of the cerebral functions. The secretion of
pineal indolic hormones is characterized by a high endogenous
rhythmic alternation, modulated by the light/darkness (L/D)
succession and by temperature as well. The research has been carried
out using 100 chicken broilers - “Ross" commercial hybrid,
randomly allocated in two experimental batches: Lc batch, reared
under a 12L/12D lighting schedule and Lexp batch, which was photic
pinealectomised through continuous exposition to light (150 lux, 24
hours, 56 days). Chemical and physical features of the meat issued
from breast fillet and thighs muscles have been studied, determining
the dry matter, proteins, fat, collagen, salt content and pH value, as
well. Besides the variations of meat chemical composition in relation
with lighting schedule, other parameters have been studied: live
weight dynamics, feed intake and somatic development degree. The
achieved results became significant since chickens have 7 days of
age, some variations of the studied parameters being registered,
revealing that the pineal gland physiologic activity, in relation with
the lighting schedule, could be interpreted through the monitoring of
the somatic development technological parameters, usually studied
within the chicken broilers rearing aviculture practice.
Abstract: Image mosaicing techniques are usually employed to offer researchers a wider field of view of microscopic image of biological samples. a mosaic is commonly achieved using automated microscopes and often with one “color" channel, whether it refers to natural or fluorescent analysis. In this work we present a method to achieve three subsequent mosaics of the same part of a stem cell culture analyzed in phase contrast and in fluorescence, with a common non-automated inverted microscope. The mosaics obtained are then merged together to mark, in the original contrast phase images, nuclei and cytoplasm of the cells referring to a mosaic of the culture, rather than to single images. The experiments carried out prove the effectiveness of our approach with cultures of cells stained with calcein (green/cytoplasm and nuclei) and hoechst (blue/nuclei) probes.
Abstract: Quaternary InxAlyGa1-x-yN semiconductors have
attracted much research interest because the use of this quaternary
offer the great flexibility in tailoring their band gap profile while
maintaining their lattice-matching and structural integrity. The
structural and optical properties of InxAlyGa1-x-yN alloys grown by
molecular beam epitaxy (MBE) is presented. The structural quality of
InxAlyGa1-x-yN layers was characterized using high-resolution X-ray
diffraction (HRXRD). The results confirm that the InxAlyGa1-x-yN
films had wurtzite structure and without phase separation. As the In
composition increases, the Bragg angle of the (0002) InxAlyGa1-x-yN
peak gradually decreases, indicating the increase in the lattice constant
c of the alloys. FWHM of (0002) InxAlyGa1-x-yN decreases with
increasing In composition from 0 to 0.04, that could indicate the
decrease of quality of the samples due to point defects leading to
non-uniformity of the epilayers. UV-VIS spectroscopy have been used
to study the energy band gap of InxAlyGa1-x-yN. As the indium (In)
compositions increases, the energy band gap decreases. However, for
InxAlyGa1-x-yN with In composition of 0.1, the band gap shows a
sudden increase in energy. This is probably due to local alloy
compositional fluctuations in the epilayer. The bowing parameter
which appears also to be very sensitive on In content is investigated
and obtained b = 50.08 for quaternary InxAlyGa1-x-yN alloys. From
photoluminescence (PL) measurement, green luminescence (GL)
appears at PL spectrum of InxAlyGa1-x-yN, emitted for all x at ~530 nm
and it become more pronounced as the In composition (x) increased,
which is believed cause by gallium vacancies and related to isolated
native defects.
Abstract: This paper investigates vortex shedding processes
occurring at the end of a stack of parallel plates, due to an oscillating
flow induced by an acoustic standing wave within an acoustic
resonator. Here, Particle Image Velocimetry (PIV) is used to quantify
the vortex shedding processes within an acoustic cycle
phase-by-phase, in particular during the “ejection" of the fluid out of
the stack. Standard hot-wire anemometry measurement is also applied
to detect the velocity fluctuations near the end of the stack.
Combination of these two measurement techniques allowed a detailed
analysis of the vortex shedding phenomena. The results obtained show
that, as the Reynolds number varies (by varying the plate thickness
and drive ratio), different flow patterns of vortex shedding are
observed by the PIV measurement. On the other hand, the
time-dependent hot-wire measurements allow obtaining detailed
frequency spectra of the velocity signal, used for calculating
characteristic Strouhal numbers. The impact of the plate thickness and
the Reynolds number on the vortex shedding pattern has been
discussed. Furthermore, a detailed map of the relationship between the
Strouhal number and Reynolds number has been obtained and
discussed.
Abstract: This paper presents an experimental investigation of
transformer dielectric response and solid insulation water content.
The dielectric response was carried out on the base of Hybrid
Frequency Dielectric Spectroscopy and Polarization Current
measurements method (FDS &PC). The calculation of the water
content in paper is based on the water content in oil and the obtained
equilibrium curves. A reference measurements were performed at
equilibrium conditions for water content in oil and paper of
transformer at different stable temperatures (25, 50, 60 and 70°C) to
prepare references to evaluate the insulation behavior at the not
equilibrium conditions. Some measurements performed at the
different simulated normal working modes of transformer operation
at the same temperature where the equilibrium conditions. The
obtained results show that when transformer temperature is mach
more than the its ambient temperature, the transformer temperature
decreases immediately after disconnecting the transformer from the
network and this temperature reduction influences the transformer
insulation condition in the measuring process. In addition to the oil
temperature at the near places to the sensors, the temperature
uniformity in transformer which can be changed by a big change in
the load of transformer before the measuring time will influence the
result. The investigations have shown that the extremely influence of
the time between disconnecting the transformer and beginning the
measurements on the results. And the online monitoring for water
content in paper measurements, on the basis of the oil water content
on line monitoring and the obtained equilibrium curves. The
measurements where performed continuously and for about 50 days
without any disconnection in the prepared the adiabatic room.
Abstract: Limited infrastructure development on peats and
organic soils is a serious geotechnical issues common to many
countries of the world especially Malaysia which distributed 1.5 mill
ha of those problematic soil. These soils have high water content and
organic content which exhibit different mechanical properties and
may also change chemically and biologically with time. Constructing
structures on peaty ground involves the risk of ground failure and
extreme settlement. Nowdays, much efforts need to be done in
making peatlands usable for construction due to increased landuse.
Deep mixing method employing cement as binders, is generally used
as measure again peaty/ organic ground failure problem. Where the
technique is widely adopted because it can improved ground
considerably in a short period of time. An understanding of
geotechnical properties as shear strength, stiffness and compressibility
behavior of these soils was requires before continues construction on
it. Therefore, 1- 1.5 meter peat soil sample from states of Johor and
an organic soil from Melaka, Malaysia were investigated. Cement
were added to the soil in the pre-mixing stage with water cement ratio
at range 3.5,7,14,140 for peats and 5,10,30 for organic soils,
essentially to modify the original soil textures and properties. The
mixtures which in slurry form will pour to polyvinyl chloride (pvc)
tube and cured at room temperature 250C for 7,14 and 28 days.
Laboratory experiments were conducted including unconfined
compressive strength and bender element , to monitor the improved
strength and stiffness of the 'stabilised mixed soils'. In between,
scanning electron miscroscopic (SEM) were observations to
investigate changes in microstructures of stabilised soils and to
evaluated hardening effect of a peat and organic soils stabilised
cement. This preliminary effort indicated that pre-mixing peat and
organic soils contributes in gaining soil strength while help the
engineers to establish a new method for those problematic ground
improvement in further practical and long term applications.
Abstract: Mushrooms are a group of fleshy macroscopic fungi.
They have been valued throughout the world as both edible and
medicine. They are highly nutritious with good amount of quality
proteins, vitamins and minerals. An edible mushroom, Calocybe
indica was selected to validate its nutritional and medicinal
properties. Since tissue damage in hyperglycemia has been related to
oxidative stress, we evaluated the enzymatic and non-enzymatic
antioxidant status in the serum, liver and kidney since they are the
target organs in diabetic complications. From the results, increased
oxidative stress and decreased antioxidants might be related to the
causation of diabetes mellitus. The treatment in the diabetic rats with
the Calocybe indica showed an increase in the antioxidant system
and decrease in the production of free radicals. The mushrooms
which contain antioxidant phytochemicals has potential free radical
scavenging capacity and hence can induce the antioxidant system in
the body significantly reduces the generated free radicals thereby
maintaining the normal levels of the antioxidants
Abstract: Since polymerase chain reaction (PCR) has been
invented, it has emerged as a powerful tool in genetic analysis. The
PCR products are closely linked with thermal cycles. Therefore, to
reduce the reaction time and make temperature distribution uniform in
the reaction chamber, a novel oscillatory thermal cycler is designed.
The sample is placed in a fixed chamber, and three constant isothermal
zones are established and lined in the system. The sample is oscillated
and contacted with three different isothermal zones to complete
thermal cycles. This study presents the design of the geometric
characteristics of the chamber. The commercial software
CFD-ACE+TM is utilized to investigate the influences of various
materials, heating times, chamber volumes, and moving speed of the
chamber on the temperature distributions inside the chamber. The
chamber moves at a specific velocity and the boundary conditions
with time variations are related to the moving speed. Whereas the
chamber moves, the boundary is specified at the conditions of the
convection or the uniform temperature. The user subroutines compiled
by the FORTRAN language are used to make the numerical results
realistically. Results show that the reaction chamber with a rectangular
prism is heated on six faces; the effects of various moving speeds of
the chamber on the temperature distributions are examined. Regarding
to the temperature profiles and the standard deviation of the
temperature at the Y-cut cross section, the non-uniform temperature
inside chamber is found as the moving speed is larger than 0.01 m/s.
By reducing the heating faces to four, the standard deviation of the
temperature of the reaction chamber is under 1.4×10-3K with the range
of velocities between 0.0001 m/s and 1 m/s. The nature convective
boundary conditions are set at all boundaries while the chamber moves
between two heaters, the effects of various moving velocities of the
chamber on the temperature distributions are negligible at the assigned
time duration.
Abstract: Nowadays, cardiac disease is one of the most common
cause of death. Each year almost one million of angioplasty interventions and stents implantations are made all over the world.
Unfortunately, in 20-30% of cases neointimal proliferations leads to
restenosis occurring within the following period of 3-6 months. Three major factors are believed to contribute mostly to the edge
restenosis: (a) mechanical damage of the artery-s wall caused by the
stent implantation, (b) interaction between the stent and the blood constituents and (c) endothelial growth stimulation by small (lower
that 1.5 Pa) and oscillating wall shear stress. Assuming that this last actor is particularly important, a numerical model of restenosis
basing on wall shear stress distribution in the stented artery was elaborated. A numerical simulations of the development of in-stent
restenosis have been performed and realistic geometric patterns of a
progressing lumen reduction have been obtained
Abstract: Dioscorea species or commonly named as yam is
reported to be one of the major food sources worldwide. This
ethnobotanical study was conducted to document local knowledge
and potentials of DioscoreahispidaDennst. and to investigate and
record its distribution in three districts of Terengganu. Information
was gathered from 23 villagers from three districts of Besut, Marang
and Setiu by using semi-structured questionnaire. The villagers were
randomly selected and no appointment was made prior to the visits.
For distribution, the location of Dioscoreahispida was recorded by
using the Global Positioning System (GPS). The villagers identified
Dioscoreahispida or locally named ubigadong by looking at the
physical characteristics that include its leaf shape, stem and the color
of the tuber-s flesh. The villagers used Dioscoreahispida in many
ways in their life such as for food, medicinal purposes and fish
poison.
Abstract: In this study acoustic emission (AE) signals obtained during deformation and fracture of two types of ferrite-martensite dual phase steels (DPS) specimens have been analyzed in frequency domain. For this reason two low carbon steels with various amounts of carbon were chosen, and intercritically heat treated. In the introduced method, identifying the mechanisms of failure in the various phases of DPS is done. For this aim, AE monitoring has been used during tensile test of several DPS with various volume fraction of the martensite (VM) and attempted to relate the AE signals and failure mechanisms in these steels. Different signals, which referred to 2-3 micro-mechanisms of failure due to amount of carbon and also VM have been seen. By Fast Fourier Transformation (FFT) of signals in distinct locations, an excellent relationship between peak frequencies in these areas and micro-mechanisms of failure were seen. The results were verified by microscopic observations (SEM).
Abstract: Elastic light single-scattering spectroscopy system
with a single optical fiber probe was employed to differentiate cancerous prostate tissue from non-cancerous prostate tissue ex-vivo just after radical prostatectomy. First, ELSSS spectra were acquired
from cancerous prostate tissue to define its spectral features. Then,
spectra were acquired from normal prostate tissue to define difference in spectral features between the cancerous and normal
prostate tissues. Of the total 66 tissue samples were evaluated from
nine patients by ELSSS system. Comparing of histopathology results
and ELSSS measurements revealed that sign of the spectral slopes of
cancerous prostate tissue is negative and non-cancerous tissue is positive in the wavelength range from 450 to 750 nm. Based on the
correlation between histopathology results and sign of the spectral
slopes, ELSSS system differentiates cancerous prostate tissue from
non- cancerous with a sensitivity of 0.95 and a specificity of 0.94.
Abstract: In this paper, we establish several oscillation criteria for the nonlinear second-order damped delay dynamic equation r(t)|xΔ(t)|β-1xΔ(t)Δ + p(t)|xΔσ(t)|β-1xΔσ(t) + q(t)f(x(τ (t))) = 0 on an arbitrary time scale T, where β > 0 is a constant. Our results generalize and improve some known results in which β > 0 is a quotient of odd positive integers. Some examples are given to illustrate our main results.
Abstract: This research presents the development of simulation
modeling for WIP management in semiconductor fabrication.
Manufacturing simulation modeling is needed for productivity
optimization analysis due to the complex process flows involved
more than 35 percent re-entrance processing steps more than 15 times
at same equipment. Furthermore, semiconductor fabrication required
to produce high product mixed with total processing steps varies from
300 to 800 steps and cycle time between 30 to 70 days. Besides the
complexity, expansive wafer cost that potentially impact the
company profits margin once miss due date is another motivation to
explore options to experiment any analysis using simulation
modeling. In this paper, the simulation model is developed using
existing commercial software platform AutoSched AP, with
customized integration with Manufacturing Execution Systems
(MES) and Advanced Productivity Family (APF) for data collections
used to configure the model parameters and data source. Model
parameters such as processing steps cycle time, equipment
performance, handling time, efficiency of operator are collected
through this customization. Once the parameters are validated, few
customizations are made to ensure the prior model is executed. The
accuracy for the simulation model is validated with the actual output
per day for all equipments. The comparison analysis from result of
the simulation model compared to actual for achieved 95 percent
accuracy for 30 days. This model later was used to perform various
what if analysis to understand impacts on cycle time and overall
output. By using this simulation model, complex manufacturing
environment like semiconductor fabrication (fab) now have
alternative source of validation for any new requirements impact
analysis.