Abstract: In sheet metal forming process, raw material
mechanical properties are important parameters. This paper is to
compare the wall’s incline angle or formability of SS 400 steel and
SUS 304 stainless steel in single point incremental forming. The two
materials are ferrous base alloyed, which have the different unit cell,
mechanical property and chemical composition. They were forming
into cone shape specimens having 100 mm diameter with different
wall’s incline angle: 90o, 75o and 60o. The investigation was
continued until the specimens formed surface facture. The
experimental result showed that the smaller the wall incline angle
higher the formability with the both materials. The formability limit
of the ferrous base alloy was approx. 60o wall’s incline angle. By
nature, SS 400 has higher formability than SUS 304. This result can
be used as the initial data in designing the single point incremental
forming parts.
Abstract: Dissimilar joining of Titanium and Aluminum thin
sheets has potential applications in aerospace and automobile
industry which can reduce weight and cost and improve strength,
corrosion resistance and high temperature properties. However
successful welding of Titanium/Aluminium sheets is of challenge due
to differences in physical, chemical and metallurgical properties
between the two. This paper describes research results of Laser Beam
Welding (LBW) of Ti/Al thin sheets in which many researchers have
recently performed and critically reviewed from different
perspectives. Also some of notable works in the field of laser welding
with changes in mechanical properties, crack propagation, diffusion
behavior, chemical potential, interfacial reaction and the
microstructure are reported.
Abstract: The hydrogenated amorphous carbon films (α-C:H)
were deposited on p-type Si (100) substrates at different thicknesses by
radio frequency plasma enhanced chemical vapor deposition
technique (rf-PECVD). Raman spectra display asymmetric
diamond-like carbon (DLC) peaks, representative of the α-C:H films.
The decrease of intensity ID/IG ratios revealed the sp3 content arise at
different thicknesses of the α-C:H films. In terms of mechanical
properties, the high hardness and elastic modulus values showed the
elastic and plastic deformation behaviors related to sp3 content in
amorphous carbon films. Electrochemical properties showed that the
α-C:H films exhibited excellent corrosion resistance in air-saturated
3.5 wt.% NaCl solution for pH 2 at room temperature. Thickness
increasing affected the small sp2 clusters in matrix, restricting the
velocity transfer and exchange of electrons. The deposited α-C:H films
exhibited excellent mechanical properties and corrosion resistance.
Abstract: Aluminum hybrid reinforcement technology is a
response to the dynamic ever increasing service requirements of such
industries as transportation, aerospace, automobile, marine, etc. It is
unique in that it offers a platform of almost unending combinations of
materials to produce various hybrid composites. This article reviews
the studies carried out on various combinations of aluminum hybrid
composite and the effects on mechanical, physical and chemical
properties. It is observed that the extent of enhancement of these
properties of hybrid composites is strongly dependent on the nature
of the reinforcement, its hardness, particle size, volume fraction,
uniformity of dispersion within the matrix and the method of hybrid
production.
Abstract: Essential oils are expensive phytochemicals produced
and extracted from specific species belonging to particular families in
the plant kingdom. In the United Arab Emirates country (UAE), is
located in the arid region of the world, nine species, from the
Lamiaceae family, having the capability to produce therapeutic grade
essential oils. These species include; Mentha spicata, Ocimum
forskolei, Salvia macrosiphon, Salvia aegyptiaca, Salvia macilenta,
Salvia spinosa, Teucrium polium, Teucrium stocksianum and Zataria
multiflora. Although, such potential species are indigenous to the
UAE, however, there are almost no studies available to investigate
the chemical composition and the quality of the extracted essential
oils under the UAE climatological conditions. Therefore, great
attention has to be given to such valuable natural resources, through
conducting highly supported research projects, tailored to the UAE
conditions, and investigating different extraction techniques,
including the application of the latest available technologies, such as
superficial fluid CO2. This is crucially needed; in order to accomplish
the greatest possibilities in the medicinal field, specifically in the
discovery of new therapeutic chemotypes, as well as, to achieve the
sustainability of this natural resource in the country.
Abstract: The biosynthesis of nanoparticles by microorganisms,
on the contrary to chemical synthesis, is an environmentally-friendly
process which has low energy requirements. In this investigation, we
used the microorganism Geobacillus wiegelii, strain GWE1, an
aerobic thermophile belonging to genus Geobacillus, isolated from a
drying oven. This microorganism has the ability to reduce selenite
evidenced by the change of color from colorless to red in the culture.
Elemental analysis and composition of the particles were verified
using transmission electron microscopy and energy-dispersive X-ray
analysis. The nanoparticles have a defined spherical shape and a
selenium elemental state. Previous experiments showed that the
presence of the whole microorganism for the reduction of selenite
was not necessary. The results strongly suggested that an intracellular
NADPH/NADH-dependent reductase mediates selenium
nanoparticles synthesis under aerobic conditions. The enzyme was
purified and identified by mass spectroscopy MALDI-TOF TOF
technique. The enzyme is a 1-pyrroline-5-carboxylate dehydrogenase.
Histograms of nanoparticles sizes were obtained. Size distribution
ranged from 40-160 nm, where 70% of nanoparticles have less than
100 nm in size. Spectroscopic analysis showed that the nanoparticles
are composed of elemental selenium. To analyse the effect of pH in
size and morphology of nanoparticles, the synthesis of them was
carried out at different pHs (4.0, 5.0, 6.0, 7.0, 8.0). For
thermostability studies samples were incubated at different
temperatures (60, 80 and 100 ºC) for 1 h and 3 h. The size of all
nanoparticles was less than 100 nm at pH 4.0; over 50% of
nanoparticles have less than 100 nm at pH 5.0; at pH 6.0 and 8.0 over
90% of nanoparticles have less than 100 nm in size. At neutral pH
(7.0) nanoparticles reach a size around 120 nm and only 20% of them
were less than 100 nm. When looking at temperature effect,
nanoparticles did not show a significant difference in size when they
were incubated between 0 and 3 h at 60 ºC. Meanwhile at 80 °C the
nanoparticles suspension lost its homogeneity. A change in size was
observed from 0 h of incubation at 80ºC, observing a size range
between 40-160 nm, with 20% of them over 100 nm. Meanwhile
after 3 h of incubation at size range changed to 60-180 nm with 50%
of them over 100 nm. At 100 °C the nanoparticles aggregate forming
nanorod structures. In conclusion, these results indicate that is
possible to modulate size and shape of biologically synthesized
nanoparticles by modulating pH and temperature.
Abstract: The aim of the present work was to statistically design
an autotrophic medium for maximum biomass production by
Chlorella pyrenoidosa using response surface methodology. After
evaluating one factor at a time approach, K2HPO4, KNO3,
MgSO4.7H2O and NaHCO3 were preferred over the other
components of the fog’s medium as most critical autotrophic medium
components. The study showed that the maximum biomass yield was
achieved while the concentrations of MgSO4.7H2O, K2HPO4, KNO3
and NaHCO3 were 0.409 g/L, 0.24 g/L, 1.033 g/L, and 3.265 g/L,
respectively. The study reported that the biomass productivity of C.
pyrenoidosa improved from 0.14 g/L in defined fog’s medium to 1.40
g/L in modified fog’s medium resulting 10 fold increase. The
biochemical composition biosynthesis of C. pyrenoidosa was altered
using nitrogen limiting stress bringing about 5.23 fold increase in
lipid content than control (cell without stress), as analyzed by FTIR
integration method.
Abstract: Hydrogenated amorphous carbon (a-C:H) films have
been synthesized by a radio frequency plasma enhanced chemical
vapor deposition (rf-PECVD) technique with different bias voltage
from 0.0 to -0.5 kV. The Raman spectra displayed the polymer-like
hydrogenated amorphous carbon (PLCH) film with 0.0 to -0.1 and
a-C:H films with -0.2 to -0.5 kV of bias voltages. The surface chemical
information of all films were studied by X-ray photoelectron
spectroscopy (XPS) technique, presented to C-C (sp2 and sp3) and C-O
bonds, and relative carbon (C) and oxygen (O) atomics contents. The
O contamination had affected on structure and optical properties. The
true density of PLCH and a-C:H films were characterized by X-ray
refractivity (XRR) method, showed the result as in the range of
1.16-1.73 g/cm3 that depending on an increasing of bias voltage. The
hardness was proportional to the true density of films. In addition, the
optical properties i.e. refractive index (n) and extinction coefficient (k)
of these films were determined by a spectroscopic ellipsometry (SE)
method that give formation to in 1.62-2.10 (n) and 0.04-0.15 (k)
respectively. These results indicated that the optical properties
confirmed the Raman results as presenting the structure changed with
applied bias voltage increased.
Abstract: Kigelia africana (Lam.) Benth. (Bignoniaceae) is a
reputed traditional remedy for various human ailments such as skin
diseases, microbial infections, melanoma, stomach troubles,
metabolic disorders, malaria and general pains. In spite of the fruit
being widely used for purposes related to its antibacterial and
antifungal properties, the chemical constituents associated with the
activity have not been fully identified. To elucidate the active
principles, we evaluated the antimicrobial activity of fruit extracts
and purified fractions against Staphylococcus aureus, Enterococcus
faecalis, Moraxella catarrhalis, Escherichia coli, Candida albicans
and Candida tropicalis. Shade-dried fruits were powdered and
extracted with hydroalcoholic (1:1) mixture by soaking at room
temperature for 72 h. The crude extract was further fractionated by
column chromatography, with successive elution using hexane,
dichloromethane, ethyl acetate, acetone and methanol. The
dichloromethane and ethyl acetate fractions were combined and
subjected to column chromatography to furnish a wax and oil from
the eluates of 20% and 40% ethyl acetate in hexane, respectively. The
GC-MS and GC×GC-MS results revealed that linoleic acid, linolenic
acid, palmitic acid, arachidic acid and stearic acid were the major
constituents in both oil and wax. The crude hydroalcoholic extract
exhibited the strongest activity with MICs of 0.125-0.5 mg/mL,
followed by the ethyl acetate (MICs = 0.125-1.0 mg/mL),
dichloromethane (MICs = 0.250-2.0 mg/mL), hexane (MICs = 0.25-
2.0 mg/mL), acetone (MICs = 0.5-2.0 mg/mL) and methanol (MICs =
1.0-2.0 mg/mL), whereas the wax (MICs = 2.0-4.0 mg/mL) and oil
(MICs = 4.0-8.0 mg/mL) showed poor activity. The study concludes
that synergistic interactions of chemical constituents could be
responsible for the antimicrobial activity of K. africana fruits, which
needs a more holistic approach to understand the mechanism of its
antimicrobial activity.
Abstract: Multiwall carbon nanotubes, prepared by chemical
vapor deposition, have an average diameter of 60-100 nm as shown
by High Resolution Transmittance Electron Microscope, HR-TEM.
The Multiwall carbon nanotubes (MWCNTs) were further
characterized using X-ray Diffraction and Raman Spectroscopy.
Mercury uptake capacity of MWCNTs was studied using batch
adsorption method at different concentration ranges up to 150 ppm.
Mercury concentration (before and after the treatment) was measured
using cold vapor atomic absorption spectroscopy. The effect of time,
concentration, pH and adsorbent dose were studied. MWCNT were
found to perform complete absorption in the sub-ppm concentrations
(parts per billion levels) while for high concentrations, the adsorption
efficiency was 92% at the optimum conditions; 0.1 g of the adsorbent
at 150 ppm mercury (II) solution. The adsorption of mercury on
MWCNTs was found to follow the Freundlich adsorption isotherm
and the pseudo-second order kinetic model.
Abstract: Fritillaria oranensis (Liliaceae) was described in 1874
by pomel from Algeria. Plant samples have been collected from the
mount of Tessala (Sidi-Bel-Abbes). The morphological features of
various organs of the plant are described in detail. In the
morphological part of the study, features of various organs of the
plants such as stem and leaf were determined and illustrated.
Ecological studies provide information about the physical and
chemical structure of soil types in Tessala Mountain. The aim of this
original investigation is to put forth ecological and anatomical
features of these species for the first time, but at the same time given
detailed account of the morphological characteristics of the stem and
leaf of Fritillaria oranensis.
Abstract: Mech-Degla, Degla-Beida and Frezza are the date
(Phoenix dactylifera L.) common varieties with a more or less good
availability and feeble trade value. Some morphologic and
physicochemical factors were determined. Results show that the
whole date weight is significantly different (P= 95%) concerning
Mech-Degla and Degla-Beida which are more commercialized than
Frezza whereas the pulp mass proportion in relation to whole fruits is
highest for Frezza (88.28%). Moreover, there is a large variability
concerning the weights and densities of constitutive tissues in each
variety. The white tissue is dominant in Mech-Degla in opposite to
the two other varieties. The variance analyze showed that the
difference in weights between brown and white tissues is significant
(P = 95%) for all studied varieties. Some other morphologic and
chemical proprieties of the whole pulps and their two constitutive
parts (brown or pigmented and white) are also investigated. The
predominance of phenolics in Mech-Degla (4.01g/100g, w.b) and
Frezza (4.96 g/100g, w.b) pulps brown part is the main result
revealed in this study.
Abstract: This paper involved the performance of a hightemperature
X-Ray powder diffraction analysis (XRD) of a sample of
chemical gypsum generated in the production of titanium white; this
gypsum originates by neutralizing highly acidic water with limestone
suspension. Specifically, it was gypsum formed in the first stage of
neutralization when the resulting material contains, apart from
gypsum, a number of waste products resulting from the
decomposition of ilmenite by sulphuric acid. So it can be described as
red titanogypsum. By conducting the experiment using XRD
apparatus Bruker D8 Advance with a Cu anode (λkα=1.54184 Å)
equipped with high-temperature chamber Anton Paar HTK 16, it was
possible to identify clearly in the sample each phase transition in the
system of CaSO4·xH2O.
Abstract: Novel bio-based polymer electrolyte was synthesized
with LiClO4 as the main source of charge carrier. Initially,
polyurethane-LiClO4 polymer electrolytes were synthesized via
prepolymerization method with different NCO/OH ratios and labelled
them as PU1, PU2, PU3 and PU4. Fourier transform infrared (FTIR)
analysis indicates the co-ordination between Li+ ion and polyurethane
in PU1. Differential scanning calorimetry (DSC) analysis indicates
PU1 has the highest glass transition temperature (Tg) corresponds to
the most abundant urethane group which is the hard segment in PU1.
Scanning electron microscopy (SEM) shows the good miscibility
between lithium salt and the polymer. The study found that PU1
possessed the greatest ionic conductivity and the lowest activation
energy, Ea. All the polyurethanes exhibited linear Arrhenius
variations indicating ion transport via simple lithium ion hopping in
polyurethane. This research proves the NCO content in polyurethane
plays an important role in affecting the ionic conductivity of this
polymer electrolyte.
Abstract: The manufacturing technology of band cotton is very
delicate and depends to choice of certain parameters such as torsion
of warp yarn.
The fabric elasticity is achieved without the use of any elastic
material, chemical expansion, artificial or synthetic and it’s capable
of creating pressures useful for therapeutic treatments.
Before use, the band is subjected to treatments of specific
preparation for obtaining certain elasticity, however, during its
treatment, there are some regression parameters. The dependence of
manufacturing parameters on the quality of the chemical treatment
was confirmed.
The aim of this work is to improve the properties of the fabric
through the development of manufacturing technology appropriately.
Finally for the treatment of the strip pancake 100% cotton, a
treatment method is recommended.
Abstract: Metal-enhanced Luminescence of silicon nanocrystals
(SiNCs) was determined using two different particle sizes of silver
nanoparticles (AgNPs). SiNCs have been characterized by scanning
electron microscopy (SEM), high resolution transmission electron
microscopy (HRTEM), Fourier transform infrared spectroscopy
(FTIR) and X-ray photoelectron spectroscopy (XPS). It is found that
the SiNCs are crystalline with an average diameter of 65 nm and FCC
lattice. AgNPs were synthesized using photochemical reduction of
AgNO3 with sodium dodecyl sulphate (SDS). The enhanced
luminescence of SiNCs by AgNPs was evaluated by confocal Raman
microspectroscopy. Enhancement up to x9 and x3 times were
observed for SiNCs that mixed with AgNPs which have an average
particle size of 100 nm and 30 nm, respectively. Silver NPs-enhanced
luminescence of SiNCs occurs as a result of the coupling between the
excitation laser light and the plasmon bands of AgNPs; thus this
intense field at AgNPs surface couples strongly to SiNCs.
Abstract: Nonalcoholic fatty liver disease (NAFLD) has
increased in conjunction with obesity. The accuracy of risk factors
for detecting NAFLD in obese adolescents has not undergone a
formal evaluation. The aim of this study was to evaluate predictors of
NAFLD among Egyptian female obese adolescents. The study
included 162 obese female adolescents. All were subjected to
anthropometry, biochemical analysis and abdominal ultrasongraphic
assessment. Metabolic syndrome (MS) was diagnosed according to
the IDF criteria. Significant association between presence of MS and
NAFLD was observed. Obese adolescents with NAFLD had
significantly higher levels of ALT, triglycerides, fasting glucose,
insulin, blood pressure and HOMA-IR, whereas decreased HDL-C
levels as compared with obese cases without NAFLD. Receiver–
operating characteristic (ROC) curve analysis shows that ALT is a
sensitive predictor for NAFLD, confirming that ALT can be used as a
marker of NAFLD.
Abstract: Mass flow measurement is the basis of most technoeconomic
formulations in the chemical industry. This calls for
reliable and accurate detection of mass flow. Flow measurement
laboratory experiments were conducted using various instruments.
These consisted of orifice plates, various sized rotameters, wet gas
meter and soap bubble meter. This work was aimed at evaluating
appropriate operating conditions and accuracy of the aforementioned
devices. The experimental data collected were compared to
theoretical predictions from Bernoulli’s equation and calibration
curves supplied by the instrument’s manufacturers. The results
obtained showed that rotameters were more reliable for measuring
high and low flow rates; while soap-bubble meters and wet-gas
meters were found to be suitable for measuring low flow rates. The
laboratory procedures and findings of the actual work can assist
engineering students and professionals in conducting their flow
measurement laboratory test work.
Abstract: An anthropometric study applied to 1,115 students of
the Faculty of Chemical Sciences and Engineering of the
Autonomous University of California. Thirteen individual
measurements were taken in a sitting position. The results obtained
allow forming a reliable anthropometric database for statistical
studies and analysis and inferences of specific distributions, so the
opinion of experts in occupational medicine recommendations may
emit to reduce risks resulting in an alteration of the vital signs during
the execution of their school activities. Another use of these analyses
is to use them as a reliable reference for future deeper research, to the
design of spaces, tools, utensils, workstations, with anthropometric
dimensions and ergonomic characteristics suitable to use.
Abstract: Pollution of the Klip River has caused
microorganisms inhabiting it to develop protective survival
mechanisms. This study isolated and characterized the heavy metal
resistant bacteria in the Klip River. Water and sediment samples were
collected from six sites along the course of the river. The pH,
turbidity, salinity, temperature and dissolved oxygen were measured
in-situ. The concentrations of six heavy metals (Cd, Cu, Fe, Ni, Pb
and Zn) of the water samples were determined by atomic absorption
spectroscopy. Biochemical and antibiotic profiles of the isolates were
assessed using the API 20E® and Kirby Bauer Method. Growth
studies were carried out using spectrophotometric methods. The
isolates were identified using 16SrDNA sequencing. The uppermost
part of the Klip River with the lowest pH had the highest levels of
heavy metals. Turbidity, salinity and specific conductivity increased
measurably at Site 4 (Henley on Klip Weir). MIC tests showed that
16 isolates exhibited high iron and lead resistance. Antibiotic
susceptibility tests revealed that the isolates exhibited multitolerances
to drugs such as Tetracycline, Ampicillin, and
Amoxicillin.