Abstract: The manufacturing technology of band cotton is very
delicate and depends to choice of certain parameters such as torsion
of warp yarn.
The fabric elasticity is achieved without the use of any elastic
material, chemical expansion, artificial or synthetic and it’s capable
of creating pressures useful for therapeutic treatments.
Before use, the band is subjected to treatments of specific
preparation for obtaining certain elasticity, however, during its
treatment, there are some regression parameters. The dependence of
manufacturing parameters on the quality of the chemical treatment
was confirmed.
The aim of this work is to improve the properties of the fabric
through the development of manufacturing technology appropriately.
Finally for the treatment of the strip pancake 100% cotton, a
treatment method is recommended.
Abstract: Because of architectural condition and structure application, sometimes mass source and stiffness source are not coincidence, and the structure is irregular. The structure is also might be asymmetric as an asymmetric bracing in plan which leads to unbalance distribution of stiffness or because of unbalance distribution of the mass. Both condition lead to eccentricity and torsion in the structure. The deficiency of ordinary code to evaluate the performance of steel structures against earthquake has been caused designing based on performance level or capacity spectrum be used. By using the mentioned methods it is possible to design a structure that its behavior against different earthquakes be predictive. In this article 5- story buildings with different percentage of asymmetric which is because of stiffness changes and kind of bracing (x and chevron bracing) have been designed. The static and dynamic nonlinear analysis under three acceleration recording has been done. Finally performance level of the structure has been evaluated.
Abstract: New advancement of technology and never satisfying demands of the civilization are putting huge pressure on the natural fuel resources and these resources are at a constant threat to its sustainability. To get the best out of the automobile, the optimum balance between performance and fuel economy is important. In the present state of art, either of the above two aspects are taken into mind while designing and development process which puts the other in the loss as increase in fuel economy leads to decrement in performance and vice-versa. In-depth observation of the vehicle dynamics apparently shows that large amount of energy is lost during braking and likewise large amount of fuel is consumed to reclaim the initial state, this leads to lower fuel efficiency to gain the same performance. Current use of Kinetic Energy Recovery System is only limited to sports vehicles only because of the higher cost of this system. They are also temporary in nature as power can be squeezed only during a small time duration and use of superior parts leads to high cost, which results on concentration on performance only and neglecting the fuel economy. In this paper Kinetic Energy Recovery System for storing the power and then using the same while accelerating has been discussed. The major storing element in this system is a Flat Spiral Spring that will store energy by compression and torsion.
The use of spring ensure the permanent storage of energy until used by the driver unlike present mechanical regeneration system in which the energy stored decreases with time and is eventually lost. A combination of internal gears and spur gears will be used in order to make the energy release uniform which will lead to safe usage. The system can be used to improve the fuel efficiency by assisting in overcoming the vehicle’s inertia after braking or to provide instant acceleration whenever required by the driver. The performance characteristics of the system including response time, mechanical efficiency and overall increase in efficiency are demonstrated. This technology makes the KERS (Kinetic Energy Recovery System) more flexible and economical allowing specific application while at the same time increasing the time frame and ease of usage.
Abstract: Based on the standard finite element method, a new
finite element method which is known as nonlocal finite element
method (NL-FEM) is numerically implemented in this article to
study the nonlocal effects for solving 1D nonlocal elastic problem.
An Eringen-type nonlocal elastic model is considered. In this model,
the constitutive stress-strain law is expressed interms of integral
equation which governs the nonlocal material behavior. The new
NL-FEM is adopted in such a way that the postulated nonlocal elastic
behavior of material is captured by a finite element endowed with a
set of (cross-stiffness) element itself by the other elements in mesh.
An example with their analytical solutions and the relevant numerical
findings for various load and boundary conditions are presented and
discussed in details. It is observed from the numerical solutions that
the torsional deformation angle decreases with increasing nonlocal
nanoscale parameter. It is also noted that the analytical solution fails
to capture the nonlocal effect in some cases where numerical
solutions handle those situation effectively which prove the
reliability and effectiveness of numerical techniques.
Abstract: Recent years, adaptive pushover methods have been
developed for seismic analysis of structures. Herein, the accuracy of
the displacement-based adaptive pushover (DAP) method, which is
introduced by Antoniou and Pinho [2004], is evaluated for Irregular
buildings. The results are compared to the force-based procedure.
Both concrete and steel frame structures, asymmetric in plan and
elevation are analyzed and also torsional effects are taking into the
account. These analyses are performed using both near fault and far
fault records. In order to verify the results, the Incremental Dynamic
Analysis (IDA) is performed.