Abstract: Excessive fretting wear at the taper-trunnion junction
(trunnionosis) apparently contributes to the high failure rates of hip
implants. Implant wear and corrosion lead to the release of metal
particulate debris and subsequent release of metal ions at the tapertrunnion
surface. This results in a type of metal poisoning referred to
as metallosis. The consequences of metal poisoning include;
osteolysis (bone loss), osteoarthritis (pain), aseptic loosening of the
prosthesis and revision surgery. Follow up after revision surgery,
metal debris particles are commonly found in numerous locations. Background: A stable connection between the femoral ball head
(taper) and stem (trunnion) is necessary to prevent relative motions
and corrosion at the taper junction. Hence, the importance of
component assembly cannot be over-emphasized. Therefore, the aim
of this study is to determine the influence of head-stem junction
assembly by press fitting and the subsequent
disengagement/disassembly on the connection strength between the
taper ball head and stem. Methods: CoCr femoral heads were assembled with High stainless
hydrogen steel stem (trunnion) by Push-in i.e. press fit; and
disengaged by pull-out test. The strength and stability of the two
connections were evaluated by measuring the head pull-out forces
according to ISO 7206-10 standards. Findings: The head-stem junction strength linearly increases with
assembly forces.
Abstract: The objective of the paper is a numerical study of heat
transfer between perforated metal plates and the surrounding air
flows. Different perforation structures can nowadays be found in
various industrial products. Besides improving the mechanical
properties, the perforations can intensify the heat transfer as well. The
heat transfer coefficient depends on a wide range of parameters such
as type of perforation, size, shape, flow properties of the surrounding
air etc. The paper was focused on three different perforation
structures which have been investigated from the point of the view of
the production in the previous studies. To determine the heat
coefficients and the Nusselt numbers, the numerical simulation
approach was adopted. The calculations were performed using the
OpenFOAM software. The three-dimensional, unstable, turbulent and
incompressible air flow around the perforated surface metal plate was
considered.
Abstract: Kurtbogazi Dam has gained special meaning for Ankara, Turkey for the last decade due to the rapid depletion of nearby resources of drinking water. In this study, the results of the analyses of Kurtbogazi Dam outlet water and the rivers flowing into the Kurtbogazi Dam were discussed for the period of last five years between 2008 and 2012. Some physical and chemical properties (pH, temperature, biochemical oxygen demand (BOD5), nitrate, phosphate and chlorine) of these water resources were evaluated. They were classified according to the Council Directive (75/440/EEC). Moreover, the properties of these surface waters were assessed to determine the quality of water for drinking and irrigation purposes using Piper, US Salinity Laboratory and Wilcox diagrams. The results showed that all the water resources are acceptable level as surface water except for Pazar Stream in terms of ortho-phosphate and BOD5 concentration for 2008.
Abstract: In this study, we investigated numerically heat
transfer by mixed convection coupled to radiation in a square cavity;
the upper horizontal wall is movable. The purpose of this study is to
see the influence of the emissivity ε and the varying of the
Richardson number Ri on the variation of average Nusselt number
Nu. The vertical walls of the cavity are differentially heated, the left
wall is maintained at a uniform temperature higher than the right
wall, and the two horizontal walls are adiabatic. The finite volume
method is used for solving the dimensionless Governing Equations.
Emissivity values used in this study are ranged between 0 and 1, the
Richardson number in the range 0.1 to 10. The Rayleigh number is
fixed to Ra=104 and the Prandtl number is maintained constant
Pr=0.71. Streamlines, isothermal lines and the average Nusselt
number are presented according to the surface emissivity. The results
of this study show that the Richardson number Ri and emissivity ε
affect the average Nusselt number.
Abstract: Pure nickel coatings have been successfully
electrodeposited on copper substrates by the pulse plating technique.
The influence of current density, duty cycle and pulse frequency on
the surface morphology, crystal orientation, and microhardness was
determined. It was found that the crystallite size of the deposit
increases with increasing current density and duty cycle. The crystal
orientation progressively changed from a random texture at 1 A/dm2
to (200) texture at 10 A/dm2. Increasing pulse frequency resulted in
increased texture coefficient and peak intensity of (111) reflection.
An increase in duty cycle resulted in considerable increase in texture
coefficient and peak intensity of (311) reflection. Coatings obtained
at high current densities and duty cycle present a mixed morphology
of small and large grains. Maximum microhardness of 193 Hv was
achieved at 4 A/dm2, 10 Hz and duty cycle of 50%. Nickel coatings
with (200) texture are ductile while (111) texture improves the
microhardness of the coatings.
Abstract: Exact solution of an unsteady MHD flow of elasticoviscous
fluid through a porous media in a tube of elliptic cross
section under the influence of magnetic field and constant pressure
gradient has been obtained in this paper. Initially, the flow is
generated by a constant pressure gradient. After attaining the steady
state, the pressure gradient is suddenly withdrawn and the resulting
fluid motion in a tube of elliptical cross section by taking into
account of the porosity factor and magnetic parameter of the
bounding surface is investigated. The problem is solved in two-stages
the first stage is a steady motion in tube under the influence of a
constant pressure gradient, the second stage concern with an unsteady
motion. The problem is solved employing separation of variables
technique. The results are expressed in terms of a non-dimensional
porosity parameter, magnetic parameter and elastico-viscosity
parameter, which depends on the Non-Newtonian coefficient. The
flow parameters are found to be identical with that of Newtonian case
as elastic-viscosity parameter, magnetic parameter tends to zero, and
porosity tends to infinity. The numerical results were simulated in
MATLAB software to analyze the effect of Elastico-viscous
parameter, porosity parameter, and magnetic parameter on velocity
profile. Boundary conditions were satisfied. It is seen that the effect
of elastico-viscosity parameter, porosity parameter and magnetic
parameter of the bounding surface has significant effect on the
velocity parameter.
Abstract: Polylactic acid (PLA) is the most commercially
available bio-based and biodegradable plastic at present. PLA has
been used in plastic related industries including single-used
containers, disposable and environmentally friendly packaging owing
to its renewability, compostability, biodegradability, and safety.
Although PLA demonstrates reasonably good optical, physical,
mechanical and barrier properties comparable to the existing
petroleum-based plastics, its brittleness and mold shrinkage as well as
its price are the points to be concerned for the production of rigid and
semi-rigid packaging. Blending PLA with other bio-based polymers
including thermoplastic starch (TPS) is an alternative not only to
achieve a complete bio-based plastic, but also to reduce the
brittleness, shrinkage during molding and production cost of the
PLA-based products. TPS is a material produced mainly from starch
which is cheap, renewable, biodegradable, compostable, and nontoxic.
It is commonly prepared by a plasticization of starch under
applying heat and shear force. Although glycerol has been reported as
one of the most plasticizers used for preparing TPS, its migration
caused the surface stickiness of the TPS products. In some cases,
mixed plasticizers or natural fibers have been applied to impede the
retrogradation of starch or reduce the migration of glycerol. The
introduction of fibers into TPS-based materials could reinforce the
polymer matrix as well. Therefore, the objective of the present
research is to study the effect of starch type (i.e. native starch and
phosphate starch), plasticizer type (i.e. glycerol and xylitol with a
weight ratio of glycerol to xylitol of 100:0, 75:25, 50:50, 25:75 and
0:100) and fiber content (i.e. in the range of 1-25 %wt) on properties
of PLA/TPS blend and composite. PLA/TPS blends and composites
were prepared using a twin-screw extruder and then converted into
dumbbell-shaped specimens using an injection molding machine. The
PLA/TPS blends prepared by using phosphate starch showed higher
tensile strength and stiffness than the blends prepared by using native
one. In contrast, the blends from native starch exhibited higher
extensibility and heat distortion temperature (HDT) than those from
the modified starch. Increasing xylitol content resulted in enhanced
tensile strength, stiffness and water resistance, but decreased
extensibility and HDT of the PLA/TPS blend. Tensile properties and
hydrophobicity of the blend could be improved by incorporating
silane treated-jute fibers.
Abstract: The present study deals with the characterization of
CrSiN coatings obtained by PVD magnetron sputtering systems.
CrSiN films were deposited with different Si contents, in order to
check the effect of at.% variation on the different properties of the
Cr–N system. Coatings were characterized by scanning electron
microscopy (SEM) for thickness measurements, X-ray diffraction.
Surface morphology and the roughness characteristics were explored
using AFM, Mechanicals properties, elastic and plastic deformation
resistance of thin films were investigated using nanoindentation test. We observed that the Si addition improved the hardness and the
Young’s modulus of the Cr–N system. Indeed, the hardness value is
18,56 GPa for CrSiN coatings. Besides, the Young’s modulus value
is 224,22 GPa for CrSiN coatings for Si content of 1.2 at.%.
Abstract: In the present study, analysis of heat transfer is carried
out in the slip flow region for the fluid flowing between two parallel
plates by employing the asymmetric heat fluxes at surface of the
plates. The flow is assumed to be hydrodynamically and thermally
fully developed for the analysis. The second order velocity slip and
viscous dissipation effects are considered for the analysis. Closed
form expressions are obtained for the Nusselt number as a function of
Knudsen number and modified Brinkman number. The limiting
condition of the present prediction for Kn = 0, Kn2 = 0, and Brq1 = 0
is considered and found to agree well with other analytical results.
Abstract: The advancements in technology allow the
development of a new system that can continuously measure surface
soil erosion. Continuous soil erosion measurements are required in
order to comprehend the erosional processes and propose effective
and efficient conservation measures to mitigate surface erosion.
Mitigating soil erosion, especially in Mediterranean countries such as
Greece, is essential in order to maintain environmental and
agricultural sustainability. In this paper, we present the Automated
Soil Erosion Monitoring System (ASEMS) that measures surface soil
erosion along with other factors that impact erosional process.
Specifically, this system measures ground level changes (surface soil
erosion), rainfall, air temperature, soil temperature, and soil moisture.
Another important innovation is that the data will be collected by
remote communication. In addition, stakeholder’s awareness is a key
factor to help reduce any environmental problem. The different
dissemination activities that were utilized are described. The overall
outcomes were the development of a new innovative system that can
measure erosion very accurately. These data from the system help
study the process of erosion and find the best possible methods to
reduce erosion. The dissemination activities enhance the stakeholders
and public's awareness on surface soil erosion problems and will lead
to the adoption of more effective soil erosion conservation practices
in Greece.
Abstract: The present study focused on the investigation of the
effects of roughness elements on heat transfer during natural
convection in a rectangular cavity using numerical technique.
Roughness elements were introduced on the bottom hot wall with a
normalized amplitude (A*/H) of 0.1. Thermal and hydrodynamic
behaviors were studied using computational method based on Lattice
Boltzmann method (LBM). Numerical studies were performed for a
laminar flow in the range of Rayleigh number (Ra) from 103 to 106
for a rectangular cavity of aspect ratio (L/H) 2.0 with a fluid of
Prandtl number (Pr) 1.0. The presence of the sinusoidal roughness
elements caused a minimum to maximum decrease in the heat
transfer as 7% to 17% respectively compared to smooth enclosure.
The results are presented for mean Nusselt number (Nu), isotherms
and streamlines.
Abstract: The study conducted a simulation of the effect of sea
water to the bonding capacity of GFRP sheet on the concrete beams
using a simulation tank. Fiber reinforced polymer (FRP) has been
developed and applied in many fields civil engineering structures on
the new structures and also for strengthening of the deteriorated
structures. The FRP has advantages such as its corrosion resistance as
well as high tensile strength to weight ratio. Compared to the other
FRP materials, Glass composed FRP (GFRP) is relatively cheaper.
GFRP sheet is applied externally by bonding it on the concrete surface.
The studies regarding the application of GFRP sheet have been
conducted such as strengthening system, bonding behavior of GFRP
sheet including the application as reinforcement in new structures. For
application to the structures with direct contact to sea environment, a
study regarding the effect of sea water to the bonding capacity of
GFRP sheet is important to be clarified. To achieve the objective of the
study, a series of concrete beams strengthened with GFRP sheet on
extreme tension surface were prepared. The beams then were stored on
the sea water tank for six months. Results indicated the bonding
capacity decreased after six month exposed to the sea water.
Abstract: Carbon Fiber Reinforced Plastics (CFRPs) are widely
used for advanced applications, in particular in aerospace, automotive
and wind energy industries. Once cured to near net shape, CFRP
parts need several finishing operations such as trimming, milling or
drilling in order to accommodate fastening hardware and meeting the
final dimensions. The present research aims to study the effect of the
cutting temperature in trimming on the mechanical strength of high
performance CFRP laminates used for aeronautics applications. The
cutting temperature is of great importance when dealing with
trimming of CFRP. Temperatures higher than the glass-transition
temperature (Tg) of the resin matrix are highly undesirable: they
cause degradation of the matrix in the trimmed edges area, which can
severely affect the mechanical performance of the entire component.
In this study, a 9.50mm diameter CVD diamond coated carbide tool
with six flutes was used to trim 24-plies CFRP laminates. A
300m/min cutting speed and 1140mm/min feed rate were used in the
experiments. The tool was heated prior to trimming using a
blowtorch, for temperatures ranging from 20°C to 300°C. The
temperature at the cutting edge was measured using embedded KType
thermocouples. Samples trimmed for different cutting
temperatures, below and above Tg, were mechanically tested using
three-points bending short-beam loading configurations. New cutting
tools as well as worn cutting tools were utilized for the experiments.
The experiments with the new tools could not prove any correlation
between the length of cut, the cutting temperature and the mechanical
performance. Thus mechanical strength was constant, regardless of
the cutting temperature. However, for worn tools, producing a cutting
temperature rising up to 450°C, thermal damage of the resin was
observed. The mechanical tests showed a reduced mean resistance in
short beam configuration, while the resistance in three point bending
decreases with increase of the cutting temperature.
Abstract: This study presents a kinematic positioning approach
that uses a global positioning system (GPS) buoy for precise ocean
surface monitoring. The GPS buoy data from the two experiments are
processed using an accurate, medium-range differential kinematic
technique. In each case, the data from a nearby coastal site are
collected at a high rate (1 Hz) for more than 24 hours, and
measurements are conducted in neighboring tidal stations to verify
the estimated sea surface heights. The GPS buoy kinematic
coordinates are estimated using epoch-wise pre-elimination and a
backward substitution algorithm. Test results show that centimeterlevel
accuracy can be successfully achieved in determining sea
surface height using the proposed technique. The centimeter-level
agreement between the two methods also suggests the possibility of
using this inexpensive and more flexible GPS buoy equipment to
enhance (or even replace) current tidal gauge stations.
Abstract: The aim of the performed work is to establish the 2D
and 3D model of direct unsteady task of sample heat treatment by
moving source employing computer model on the basis of finite
element method. Complex boundary condition on heat loaded sample
surface is the essential feature of the task. Computer model describes
heat treatment of the sample during heat source movement over the
sample surface. It is started from 2D task of sample cross section as a
basic model. Possibilities of extension from 2D to 3D task are
discussed. The effect of the addition of third model dimension on
temperature distribution in the sample is showed. Comparison of
various model parameters on the sample temperatures is observed.
Influence of heat source motion on the depth of material heat
treatment is shown for several velocities of the movement. Presented
computer model is prepared for the utilization in laser treatment of
machine parts.
Abstract: This study aims at improving the urban hydrological
cycle of the Orléans agglomeration (France) and understanding the
relationship between physical and chemical parameters of urban
surface runoff and the hydrological conditions. In particular water
quality parameters such as pH, conductivity, total dissolved solids,
major dissolved cations and anions, and chemical and biological
oxygen demands were monitored for three types of urban water
discharges (wastewater treatment plant output (WWTP), storm
overflow and stormwater outfall) under two hydrologic scenarios (dry
and wet weather). The first results were obtained over a period of five
months. Each investigated (Ormes, l’Egoutier and La Corne) outfall
represents an urban runoff source that receives water from runoff
roads, gutters, the irrigation of gardens and other sources of flow over
the Earth’s surface that drains in its catchments and carries it to the
Loire River. In wet weather conditions there is rain water runoff and
an additional input from the roof gutters that have entered the
stormwater system during rainfall. For the comparison the results La
Chilesse is a storm overflow that was selected in our study as a
potential source of waste water which is located before the (WWTP). The comparison of the physical-chemical parameters (total
dissolved solids, turbidity, pH, conductivity, dissolved organic
carbon (DOC), concentration of major cations and anions) together
with the chemical oxygen demand (COD) and biological oxygen
demand (BOD) helped to characterize sources of runoff waters in the
different watersheds. It also helped to highlight the infiltration of
wastewater in some stormwater systems that reject directly in the
Loire River. The values of the conductivity measured in the outflow
of Ormes were always higher than those measured in the other two
outlets. The results showed a temporal variation for the Ormes outfall
of conductivity from 1465 μS cm-1 in the dry weather flow to 650 μS
cm-1 in the wet weather flow and also a spatial variation in the wet
weather flow from 650 μS cm-1 in the Ormes outfall to 281 μS cm-1
in L’Egouttier outfall. The ultimate BOD (BOD28) showed a
significant decrease in La Corne outfall from 181 mg L-1 in the wet
weather flow to 95 mg L-1 in the dry weather flow because of the
nutrient load that was transported by the runoff.
Abstract: The effects of wood ash from five common tropical
woods on the ignition point of four common tropical woods in
Nigeria were investigated. The ash and moisture contents of the wood
sawdust from Mahogany (Khaya ivorensis), Opepe (Sarcocephalus
latifolius), Abura (Mitragyna ciliata), Rubber (Heavea brasilensis)
and Poroporo (Sorghum bicolour) used, were determined using a
furnace (Vecstar furnaces, model ECF2, serial no. f3077) and oven
(Genlab laboratory oven, model MINO/040) respectively. The metal
contents of the five wood sawdust ash samples were determined
using a Perkin Elmer optima 3000 dv atomic absorption spectrometer
while the ignition points were determined using Vecstar furnaces
model ECF2. Poroporo had the highest ash content, 2.263g while
rubber had the least, 0.710g. The results for the moisture content
range from 2.971g to 0.903g. Magnesium metal had the highest
concentration of all the metals, in all the wood ash samples; with
mahogany ash having the highest concentration, 9.196ppm while
rubber ash had the least concentration of magnesium metal, 2.196
ppm. The ignition point results showed that the wood ashes from
mahogany and opepe increased the ignition points of the test wood
samples, Danta (Nesogordonia papaverifera), Ekpaya, Akomu
(Pycnanthus angolensis) and Oleku when coated on them while the
ashes from poroporo, rubber and abura decreased the ignition points
of the test wood samples when coated on them. However, Opepe saw
dust ash decreased the ignition point in one of the test wood samples,
suggesting that the metal content of the test wood sample was more
than that of the Opepe saw dust ash. Therefore, Mahogany and Opepe
saw dust ashes could be used in the surface treatment of wood to
enhance their fire resistance or retardancy. However, the caution to
be exercised in this application is that the metal content of the test
wood samples should be evaluated as well.
Abstract: An experimental study with four different types of bed
conditions was carried out to understand the effect of roughness in
open channel flow at two different Reynolds numbers. The bed
conditions include a smooth surface and three different roughness
conditions, which were generated using sand grains with a median
diameter of 2.46 mm. The three rough conditions include a surface
with distributed roughness, a surface with continuously distributed
roughness and a sand bed with a permeable interface. A commercial
two-component fibre-optic LDA system was used to conduct the
velocity measurements. The variables of interest include the mean
velocity, turbulence intensity, correlation between the streamwise and
the wall normal turbulence, Reynolds shear stress and velocity triple
products. Quadrant decomposition was used to extract the magnitude
of the Reynolds shear stress of the turbulent bursting events. The
effect of roughness was evident throughout the flow depth. The
results show that distributed roughness has the greatest roughness
effect followed by the sand bed and the continuous roughness.
Compared to the smooth bed, the streamwise turbulence intensity
reduces but the vertical turbulence intensity increases at a location
very close to the bed due to the introduction of roughness. Although
the same sand grain is used to create the three different rough bed
conditions, the difference in the turbulence intensity is an indication
that the specific geometry of the roughness has an influence on
turbulence structure.
Abstract: The influence of Islam on arts can be found primarily
in calligraphy, arabesque designs and architecture. Also, geometric
designs were used quite extensively. Muslim craftsmen produced
stunning designs based on simple geometric principles and traditional
motifs which were used to decorate many surfaces. The idea of
interlacing simple rectilinear lines to form the patterns impressed
Arabs. Nomads of Persia, Turks and Mongols were equally
impressed with the designs so they begin to use them in their homes
in carpet weaving. Islamic designs, motifs and colours which were
used became common place and served to influence people’s tastes.
Modern life style and contemporary products have changed the style
of people’s daily lives, however, people still long for the nomadic
way of life. This is clearly reflected in people’s homes. In a great
many Muslim homes, Islamic decorative motifs can be seen along
with traditional ‘Bedouin’ style furnishing, especially in homes of the
Arabian Peninsula.
Abstract: In this paper, we present a comparative study of three
methods of 2D face recognition system such as: Iso-Geodesic Curves
(IGC), Geodesic Distance (GD) and Geodesic-Intensity Histogram
(GIH). These approaches are based on computing of geodesic
distance between points of facial surface and between facial curves.
In this study we represented the image at gray level as a 2D surface in
a 3D space, with the third coordinate proportional to the intensity
values of pixels. In the classifying step, we use: Neural Networks
(NN), K-Nearest Neighbor (KNN) and Support Vector Machines
(SVM). The images used in our experiments are from two wellknown
databases of face images ORL and YaleB. ORL data base was
used to evaluate the performance of methods under conditions where
the pose and sample size are varied, and the database YaleB was used
to examine the performance of the systems when the facial
expressions and lighting are varied.