Abstract: The New Basel Capital Accord (Basel II) influences how financial institutions around the world, and especially European Union institutions, determine the amount of capital to reserve. However, as the recent global crisis has shown, the revision of Basel II is needed to reflect current trends, such as increased volatility and correlation, in the world financial markets. The overall objective of Basel II is to increase the safety and soundness of the international financial system. Basel II builds on three main pillars: Pillar I deals with the minimum capital requirements for credit, market and operational risk, Pillar II focuses on the supervisory review process and finally Pillar III promotes market discipline through enhanced disclosure requirements for banks. The aim of this paper is to provide the historical background, key features and impact of Basel II on financial markets. Moreover, we discuss new proposals for international bank regulation (sometimes referred to as Basel III) which include requirements for higher quality, constituency and transparency of banks' capital and risk management, regulation of OTC markets and introduction of new liquidity standards for internationally active banks.
Abstract: A bond graph model of a two degrees of freedom
PUMA is described. System inversion gives the system input
required to generate a given system output. In order to get the system
inversion of the PUMA manipulator, a linearization of the nonlinear
bond graph is obtained. Hence, the bicausality of the linearized bond
graph of the PUMA manipulator is applied. Thus, the bicausal bond
graph provides a systematic way of generating the equations of the
system inversion. Simulation results to verify the calculated input for
a given output are shown.
Abstract: In this work, we study the problem of determining
the minimum scheduling length that can satisfy end-to-end (ETE)
traffic demand in scheduling-based multihop WSNs with cooperative
multiple-input multiple-output (MIMO) transmission scheme. Specifically,
we present a cross-layer formulation for the joint routing,
scheduling and stream control problem by incorporating various
power and rate adaptation schemes, and taking into account an
antenna beam pattern model and the signal-to-interference-and-noise
(SINR) constraint at the receiver. In the context, we also propose
column generation (CG) solutions to get rid of the complexity
requiring the enumeration of all possible sets of scheduling links.
Abstract: The study aimed to investigate characteristics of
vegetative tissue for taxonomic purpose and possibly trend of waste
application in industry. Stems and branches of 15 species in Solanum
found in Thailand were prepared for fiber and examined by light
microscopy. Microstructural characteristic data of fiber i.e. fiber
length and width, fiber lumen diameter and fiber cell wall thickness
were recorded. The longest average fiber cell length (>3.9 mm.) were
obtained in S. lycopersicum L. and S. tuberosum L. Fiber cells from
S. lycopersicum also revealed the widest average diameter of whole
cell and its lumen at >45.5 μm and >29 μm respectively. However
fiber cells with thickest wall of > 9.6 μm were belonged to the
ornamental tree species, S. wrightii Benth. The results showed that
the slenderness ratio, Runkel ratio, and flexibility coefficient, with
potentially suitable for feedstock in paper industry fell in 4 exotic
species, i.e. Solanumamericanum L., S. lycopersicum, S.
seaforthianum Andr., and S. tuberosum L
Abstract: Functional near infrared spectroscopy (fNIRS) is a
practical non-invasive optical technique to detect characteristic of
hemoglobin density dynamics response during functional activation of
the cerebral cortex. In this paper, fNIRS measurements were made in
the area of motor cortex from C4 position according to international
10-20 system. Three subjects, aged 23 - 30 years, were participated in
the experiment.
The aim of this paper was to evaluate the effects of different motor
activation tasks of the hemoglobin density dynamics of fNIRS signal.
The chaotic concept based on deterministic dynamics is an important
feature in biological signal analysis. This paper employs the chaotic
properties which is a novel method of nonlinear analysis, to analyze
and to quantify the chaotic property in the time series of the
hemoglobin dynamics of the various motor imagery tasks of fNIRS
signal. Usually, hemoglobin density in the human brain cortex is
found to change slowly in time. An inevitable noise caused by various
factors is to be included in a signal. So, principle component analysis
method (PCA) is utilized to remove high frequency component. The
phase pace is reconstructed and evaluated the Lyapunov spectrum, and
Lyapunov dimensions. From the experimental results, it can be
conclude that the signals measured by fNIRS are chaotic.
Abstract: Power transformers are among the most important and
expensive equipments in the electric power systems. Consequently
the transformer protection is an essential part of the system
protection. This paper presents a new method for locating
transformer winding faults such as turn-to-turn, turn-to-core, turn-totransformer
body, turn-to-earth, and high voltage winding to low
voltage winding. In this study the current and voltage signals of input
and output terminals of the transformer are measured, which the
Fourier transform of measured signals and harmonic analysis
determine the fault's location.
Abstract: This research aims to study consumer acceptance of Tempeh from various raw materials (type of bean) and determine protein contents for comparison. Tempeh made from soybean, peanut, white kidney bean and sesame in the ratio: - soybean:sesame =1:0.1, soybean:white kidney:sesame =1:1:0.1, soybean:peanut:sesame =1:1:0.1 and peanut:white kidney bean: sesame =1:1:0.1. The study found that consumer is most satisfied with appearances on soybean mixed with white kidney and black sesame tempeh (3.98). The most satisfied tempeh with textures is soybean mixed with peanut and black sesame tempeh (4.00). The most satisfied tempeh with odor is peanut mixed with white kidney bean and black sesame tempeh (4.04). And the most satisfied tempeh with flavor is peanut mixed with white kidney bean and black sesame tempeh (4.2). The amount of protein in production, soybean tempeh has the highest protein. When we add sesame seeds, it made the protein content slightly decreased (1.86 and 0.6 %). When we use peanut as raw material, the protein content decreased 15.3%. And when we use
white kidney bean as raw material, the protein content decreased (22.77- 26.11%).
Abstract: Automatic reusability appraisal is helpful in
evaluating the quality of developed or developing reusable software
components and in identification of reusable components from
existing legacy systems; that can save cost of developing the
software from scratch. But the issue of how to identify reusable
components from existing systems has remained relatively
unexplored. In this research work, structural attributes of software
components are explored using software metrics and quality of the
software is inferred by different Neural Network based approaches,
taking the metric values as input. The calculated reusability value
enables to identify a good quality code automatically. It is found that
the reusability value determined is close to the manual analysis used
to be performed by the programmers or repository managers. So, the
developed system can be used to enhance the productivity and
quality of software development.
Abstract: .Hardware realization of a Neural Network (NN), to a large extent depends on the efficient implementation of a single neuron. FPGA-based reconfigurable computing architectures are suitable for hardware implementation of neural networks. FPGA realization of ANNs with a large number of neurons is still a challenging task. This paper discusses the issues involved in implementation of a multi-input neuron with linear/nonlinear excitation functions using FPGA. Implementation method with resource/speed tradeoff is proposed to handle signed decimal numbers. The VHDL coding developed is tested using Xilinx XC V50hq240 Chip. To improve the speed of operation a lookup table method is used. The problems involved in using a lookup table (LUT) for a nonlinear function is discussed. The percentage saving in resource and the improvement in speed with an LUT for a neuron is reported. An attempt is also made to derive a generalized formula for a multi-input neuron that facilitates to estimate approximately the total resource requirement and speed achievable for a given multilayer neural network. This facilitates the designer to choose the FPGA capacity for a given application. Using the proposed method of implementation a neural network based application, namely, a Space vector modulator for a vector-controlled drive is presented
Abstract: Obstructive sleep apnea in patients, between 70 and 80
percent, can be cured with just a posture correcting. The most import
thing to do this is detection of obstructive sleep apnea. Detection of
obstructive sleep apnea can be performed through heart rate variability
analysis using power spectrum density analysis. After HRV analysis
we needed to know the current position information for correcting the
position. The pressure sensors of the array type were used to obtain
position information. These sensors can obtain information from the
experimenter about position. In addition, air cylinder corrected the
position of the experimenter by lifting the bed. The experimenter can
be changed position without breaking during sleep by the system.
Polysomnograph recording were obtained from 10 patients. The
results of HRV analysis were that NLF and LF/HF ratio increased,
while NHF decreased during OSA. Position change had to be done the
periods.
Abstract: This paper presents the 20-GHz fractional PLL (Phase
Locked Loop) circuit for the next generation Wi-Fi by using 90 nm
TSMC process. The newly suggested millimeter wave 16/17
pre-scalar is designed and verified by measurement to make the
fractional PLL having a low quantization noise. The operational
bandwidth of the 60 GHz system is 15 % of the carrier frequency
which requires large value of Kv (VCO control gain) resulting in
degradation of phase noise. To solve this problem, this paper adopts
AFC (Automatic Frequency Controller) controlled 4-bit millimeter
wave VCO with small value of Kv. Also constant Kv is implemented
using 4-bit varactor bank. The measured operational bandwidth is 18.2
~ 23.2 GHz which is 25 % of the carrier frequency. The phase noise of
-58 and -96.2 dBc/Hz at 100 KHz and 1 MHz offset is measured
respectively. The total power consumption of the PLL is only 30 mW.
Abstract: This paper reported an experimental research of
steady-state heat transfer behaviour of a gas flowing through a fixed
bed under the different operating conditions. Studies had been carried
out in a fixed-bed packed methanol synthesis catalyst percolated by air
at appropriate flow rate. Both radial and axial direction temperature
distribution had been investigated under the different operating
conditions. The effects of operating conditions including the reactor
inlet air temperature, the heating pipe temperature and the air flow rate
on temperature distribution was investigated and the experimental
results showed that a higher inlet air temperature was conducive to
uniform temperature distribution in the fixed bed. A large temperature
drop existed at the radial direction, and the temperature drop increased
with the heating pipe temperature increasing under the experimental
conditions; the temperature profile of the vicinity of the heating pipe
was strongly affected by the heating pipe temperature. A higher air
flow rate can improve the heat transfer in the fixed bed. Based on the
thermal distribution, heat transfer models of the fixed bed could be
established, and the characteristics of the temperature distribution in
the fixed bed could be finely described, that had an important practical
significance.
Abstract: In this paper, a uniform calculus-based approach for
synthesizing monitors checking correctness properties specified by a
large variety of logics at runtime is provided, including future and past
time logics, interval logics, state machine and parameterized temporal
logics. We present a calculus mechanism to synthesize monitors from
the logical specification for the incremental analysis of execution
traces during test and real run. The monitor detects both good and bad
prefix of a particular kind, namely those that are informative for the
property under investigation. We elaborate the procedure of calculus
as monitors.
Abstract: Recently, web services to access from many type devices
are often used. We have developed the shortest path planning
system called "Bus-Net" in Tottori prefecture as a web application
to sustain the public transport. And it used the same user interface
for both devices. To support both devices, the interface cannot use
JavaScript and so on.
Thus, we developed the method that use individual user interface
for each device type to improve its convenience. To be concrete,
we defined formats of condition input to the path planning system
and result output from it and separate the system into the request
processing part and user interface parts that depend on device types.
By this method, we have also developed special device for Bus-Net
named "Intelligent-Bus-Stop".
Abstract: Image compression can improve the performance of
the digital systems by reducing time and cost in image storage
and transmission without significant reduction of the image quality.
Furthermore, the discrete cosine transform has emerged as the new
state-of-the art standard for image compression. In this paper, a
hybrid image compression technique based on reversible blockade
transform coding is proposed. The technique, implemented over
regions of interest (ROIs), is based on selection of the coefficients
that belong to different transforms, depending on the coefficients is
proposed. This method allows: (1) codification of multiple kernals
at various degrees of interest, (2) arbitrary shaped spectrum,and (3)
flexible adjustment of the compression quality of the image and the
background. No standard modification for JPEG2000 decoder was
required. The method was applied over different types of images.
Results show a better performance for the selected regions, when
image coding methods were employed for the whole set of images.
We believe that this method is an excellent tool for future image
compression research, mainly on images where image coding can
be of interest, such as the medical imaging modalities and several
multimedia applications. Finally VLSI implementation of proposed
method is shown. It is also shown that the kernal of Hartley and
Cosine transform gives the better performance than any other model.
Abstract: This paper features the modeling and design of a
Robust Decentralized Fast Output Sampling (RDFOS) Feedback
control technique for the active vibration control of a smart flexible
multimodel Euler-Bernoulli cantilever beams for a multivariable
(MIMO) case by retaining the first 6 vibratory modes. The beam
structure is modeled in state space form using the concept of
piezoelectric theory, the Euler-Bernoulli beam theory and the Finite
Element Method (FEM) technique by dividing the beam into 4 finite
elements and placing the piezoelectric sensor / actuator at two finite
element locations (positions 2 and 4) as collocated pairs, i.e., as
surface mounted sensor / actuator, thus giving rise to a multivariable
model of the smart structure plant with two inputs and two outputs.
Five such multivariable models are obtained by varying the
dimensions (aspect ratios) of the aluminium beam. Using model
order reduction technique, the reduced order model of the higher
order system is obtained based on dominant Eigen value retention
and the Davison technique. RDFOS feedback controllers are
designed for the above 5 multivariable-multimodel plant. The closed
loop responses with the RDFOS feedback gain and the magnitudes of
the control input are obtained and the performance of the proposed
multimodel smart structure system is evaluated for vibration control.
Abstract: Worm propagation profiles have significantly changed
since 2003-2004: sudden world outbreaks like Blaster or Slammer
have progressively disappeared and slower but stealthier worms
appeared since, most of them for botnets dissemination. Decreased
worm virulence results in more difficult detection.
In this paper, we describe a stealth worm propagation model
which has been extensively simulated and analysed on a huge virtual
network. The main features of this model is its ability to infect any
Internet-like network in a few seconds, whatever may be its size while
greatly limiting the reinfection attempt overhead of already infected
hosts. The main simulation results shows that the combinatorial
topology of routing may have a huge impact on the worm propagation
and thus some servers play a more essential and significant role than
others. The real-time capability to identify them may be essential to
greatly hinder worm propagation.
Abstract: TiO2/Ag composite films were prepared by
incorporating Ag in the pores of mesoporous TiO2 films using a
photoreduction method. The Ag nanoparticle sizes were in a range of
3.66-38.56 nm. The TiO2/Ag composite films were characterized by
X-ray diffraction (XRD), scanning electron microscopy (SEM) and
transmission electron microscropy (TEM). The TiO2 films and
TiO2/Ag composite films were immersed in a 0.3 mM N719 dye
solution and characterized by UV-Vis spectrophotometer. The
TiO2/Ag/N719 composite film showed that an optimal size of Ag
nanoparticles was 19.12 nm and, hence, gave the maximum optical
absorption spectra. The improved absorption was due to surface
plasmon resonance induced by the Ag nanoparticles to enhance the
absorption coefficient of the dye.
Abstract: In this paper, we present a cost-effective wireless
distributed load shedding system for non-emergency scenarios. In
power transformer locations where SCADA system cannot be used,
the proposed solution provides a reasonable alternative that combines
the use of microcontrollers and existing GSM infrastructure to send
early warning SMS messages to users advising them to proactively
reduce their power consumption before system capacity is reached
and systematic power shutdown takes place.
A novel communication protocol and message set have been
devised to handle the messaging between the transformer sites, where
the microcontrollers are located and where the measurements take
place, and the central processing site where the database server is
hosted. Moreover, the system sends warning messages to the endusers
mobile devices that are used as communication terminals. The
system has been implemented and tested via different experimental
results.
Abstract: Today-s Information and Knowledge Society has
placed new demands on education and a new paradigm of education
is required. Learning, facilitated by educational systems and the
pedagogic process, is globally undergoing dramatic changes. The aim
of this paper is the development of a simple Instructional Design tool
for E-Learning, named IDEL (Instructional Design for Electronic
Learning), that provides the educators with facilities to create their
own courses with the essential educational material and manage
communication with students. It offers flexibility in the way of
learning and provides ease in employment and reusability of
resources. IDEL is a web-based Instructional System and is designed
to facilitate course design process in accordance with the ADDIE
model and the instructional design principles with emphasis placed
on the use of technology enhanced learning. An example case of
using the ADDIE model to systematically develop a course and its
implementation with the aid of IDEL is given and some results from
student evaluation of the tool and the course are reported.