Abstract: The effect of additional magnesium oxide (MgO) was
investigated by using the tungsten oxide supported on silica catalyst
(WOx/SiO2) physically mixed with MgO in a weight ratio 1:1. The
both fresh and spent catalysts were characterized by FT-Raman
spectrometer, UV-Vis spectrometer, X-Ray diffraction (XRD) and
temperature programmed oxidation (TPO). The results indicated that
the additional MgO could enhance the conversion of trans-2-butene
due to isomerization reaction. However, adding MgO would increase
the amount of coke deposit on the WOx/SiO2 catalyst. The TPO
profile presented two peaks when the WOx/SiO2 catalyst was
physically mixed with MgO. The further peak was suggested that
came from coke precursor could be produced by isomerization
reaction of undesired product. Then, the occurred coke precursor
could deposit and form coke on the acid catalyst.
Abstract: Failure of typical seismic frames has been found by
plastic hinge occurring on beams section near column faces. On the
other hand, the seismic capacity of the frames can be enhanced if the
plastic hinges of the beams are shifted away from the column faces.
This paper presents detailing of reinforcements in the interior beam–
column connections aiming to relocate the plastic hinge of reinforced
concrete and precast concrete frames. Four specimens were tested
under quasi-static cyclic load including two monolithic specimens
and two precast specimens. For one monolithic specimen, typical
seismic reinforcement was provided and considered as a reference
specimen named M1. The other reinforced concrete frame M2
contained additional intermediate steel in the connection area
compared with the specimen M1. For the precast specimens,
embedded T-section steels in joint were provided, with and without
diagonal bars in the connection area for specimen P1 and P2,
respectively. The test results indicated the ductile failure with beam
flexural failure in monolithic specimen M1 and the intermediate steel
increased strength and improved joint performance of specimen M2.
For the precast specimens, cracks generated at the end of the steel
inserts. However, slipping of reinforcing steel lapped in top of the
beams was seen before yielding of the main bars leading to the brittle
failure. The diagonal bars in precast specimens P2 improved the
connection stiffness and the energy dissipation capacity.
Abstract: With the growing of computer and network, digital
data can be spread to anywhere in the world quickly. In addition,
digital data can also be copied or tampered easily so that the security
issue becomes an important topic in the protection of digital data.
Digital watermark is a method to protect the ownership of digital data.
Embedding the watermark will influence the quality certainly. In this
paper, Vector Quantization (VQ) is used to embed the watermark into
the image to fulfill the goal of data hiding. This kind of watermarking
is invisible which means that the users will not conscious the existing
of embedded watermark even though the embedded image has tiny
difference compared to the original image. Meanwhile, VQ needs a lot
of computation burden so that we adopt a fast VQ encoding scheme by
partial distortion searching (PDS) and mean approximation scheme to
speed up the data hiding process.
The watermarks we hide to the image could be gray, bi-level and
color images. Texts are also can be regarded as watermark to embed.
In order to test the robustness of the system, we adopt Photoshop to
fulfill sharpen, cropping and altering to check if the extracted
watermark is still recognizable. Experimental results demonstrate that
the proposed system can resist the above three kinds of tampering in
general cases.
Abstract: Micro-electromechanical system (MEMS)
accelerometers and gyroscopes are suitable for the inertial navigation
system (INS) of many applications due to low price, small
dimensions and light weight. The main disadvantage in a comparison
with classic sensors is a worse long term stability. The estimation
accuracy is mostly affected by the time-dependent growth of inertial
sensor errors, especially the stochastic errors. In order to eliminate
negative effects of these random errors, they must be accurately
modeled. In this paper, the Allan variance technique will be used in
modeling the stochastic errors of the inertial sensors. By performing
a simple operation on the entire length of data, a characteristic curve
is obtained whose inspection provides a systematic characterization
of various random errors contained in the inertial-sensor output data.
Abstract: Heat transfer of leaves is a crucial factor in optimal
operation of metabolic functions in plants. In order to quantify this
phenomenon in different leaves and investigate the influence of leaf
shape on heat transfer, natural convection for pine, orange and olive
leaves was simulated as representatives of different groups of leaf
shapes. CFD techniques were used in this simulation with the
purpose to calculate heat transfer of leaves in similar environmental
conditions. The problem was simulated for steady state and threedimensional
conditions. From obtained results, it was concluded that
heat fluxes of all three different leaves are almost identical, however,
total rate of heat transfer have highest and lowest values for orange
leaves, and pine leaves, respectively.
Abstract: Ibeno, Nigeria hosts the operational base of Mobil
Producing Nigeria Unlimited (MPNU), a subsidiary of ExxonMobil
and the current highest oil & condensate producer in Nigeria. Besides
MPNU, other oil companies operate onshore, on the continental shelf
and deep offshore of the Atlantic Ocean in Ibeno, Nigeria. This study
was designed to delineate oil polluted sites in Ibeno, Nigeria using
geophysical methods of electrical resistivity (ER) and ground
penetrating radar (GPR). Results obtained revealed that there have
been hydrocarbon contaminations of this environment by past crude
oil spills as observed from high resistivity values and GPR profiles
which clearly show the distribution, thickness and lateral extent of
hydrocarbon contamination as represented on the radargram reflector
tones. Contaminations were of varying degrees, ranging from slight
to high, indicating levels of substantial attenuation of crude oil
contamination over time. Moreover, the display of relatively lower
resistivities of locations outside the impacted areas compared to
resistivity values within the impacted areas and the 3-D Cartesian
images of oil contaminant plume depicted by red, light brown and
magenta for high, low and very low oil impacted areas, respectively
confirmed significant recent pollution of the study area with crude
oil.
Abstract: The seismic risk mitigation from the perspective of
the old buildings stock is truly essential in Algerian urban areas,
particularly those located in seismic prone regions, such as Annaba
city, and which the old buildings present high levels of degradation
associated with no seismic strengthening and/or rehabilitation
concerns. In this sense, the present paper approaches the issue of the
seismic vulnerability assessment of old masonry building stocks
through the adaptation of a simplified methodology developed for a
European context area similar to that of Annaba city, Algeria.
Therefore, this method is used for the first level of seismic
vulnerability assessment of the masonry buildings stock of the old
city center of Annaba. This methodology is based on a vulnerability
index that is suitable for the evaluation of damage and for the
creation of large-scale loss scenarios. Over 380 buildings were
evaluated in accordance with the referred methodology and the
results obtained were then integrated into a Geographical Information
System (GIS) tool. Such results can be used by the Annaba city
council for supporting management decisions, based on a global view
of the site under analysis, which led to more accurate and faster
decisions for the risk mitigation strategies and rehabilitation plans.
Abstract: Pt/γ-Al2O3 membrane catalysts were prepared via an
evaporative-crystallization deposition method. The obtained Pt/γ-
Al2O3 catalyst activity was tested after characterization (SEM-EDAX
observation, BET measurement, permeability assessment) in the
catalytic oxidation of selected volatile organic compound (VOC) i.e.
propane, fed in mixture of oxygen. The VOC conversion (nearly
90%) obtained by varying the operating temperature showed that
flow-through membrane reactor might do better in the abatement of
VOCs.
Abstract: An unconventional composite inorganic ceramic
membrane capable of enhancing carbon dioxide emission decline was
fabricated and tested at laboratory scale in conformism to various
environmental guidelines and also to mitigate the effect of global
warming. A review of the existing membrane technologies for carbon
capture including the relevant gas transport mechanisms is presented.
Single gas permeation experiments using silica modified ceramic
membrane with internal diameter 20mm, outside diameter 25mm and
length of 368mm deposited on a macro porous support was carried
out to investigate individual gas permeation behaviours at different
pressures at room temperature. Membrane fabrication was achieved
using after a dip coating method. Nitrogen, Carbon dioxide, Argon,
Oxygen and Methane pure gases were used to investigate their
individual permeation rates at various pressures. Results show that
the gas flow rate increases with pressure drop. However above a
pressure of 3bar, CO2 permeability ratio to that of the other gases
indicated control of a more selective surface adsorptive transport
mechanism.
Abstract: Mangosteen (Garcinia mangostana) pericarp is
considered as agricultural waste and not fully utilized in food
products. It is widely reported that mangosteen pericarp contains high
antioxidant properties. The objective of this study is to develop novel
yellow alkaline noodle (YAN) substituted with different levels of
mangosteen pericarp powder (MPP). YAN formulation was
substituted with different levels of MPP (0%, 5%, 10% and 15%).
The effect on nutritional and antioxidant properties was evaluated.
Higher substitution levels of MPP resulted in significant increase
(p
Abstract: In this research numerical simulations are performed,
using the multi-relaxation-time lattice Boltzmann method, in the
range 3 ≤ β = w[d] ≤ 30 at Re = 100, 200 and 300, where β the
blockage ratio, w is the equispaced distance between centers of
cylinders, d is the diameter of the cylinder and Re is the Reynolds
number, respectively. Special attention is paid to the effect of the
equispaced distance between centers of cylinders. Visualization of
the vorticity contour visualization are presented for some simulation
showing the flow dynamics and patterns for blockage effect. Results
show that the drag and mean drag coefficients, and Strouhal number,
in general, decrease with the increase of β for fixed Re. It is found
that the decreasing rate of drag and mean drag coefficients and
Strouhal number is more distinct in the range 3 ≤ β ≤ 15. We found
that when β > 15, the blockage effect almost diminishes. Our results
further indicate that the drag and mean drag coefficients, peak value
of the lift coefficient, root-mean-square value of the lift and drag
coefficients and the ratio between lift and drag coefficients decrease
with the increase of Re. The results indicate that symmetry boundary
condition have more blockage effect as compared to periodic
boundary condition.
Abstract: This study investigates the use of a time-series of
MODIS NDVI data to identify agricultural land cover change on an
annual time step (2007 - 2012) and characterize the trend. Following
an ISODATA classification of the MODIS imagery to selectively
mask areas not agriculture or semi-natural, NDVI signatures were
created to identify areas cereals and vineyards with the aid of
ancillary, pictometry and field sample data for 2010. The NDVI
signature curve and training samples were used to create a decision
tree model in WEKA 3.6.9 using decision tree classifier (J48)
algorithm; Model 1 including ISODATA classification and Model 2
not. These two models were then used to classify all data for the
study area for 2010, producing land cover maps with classification
accuracies of 77% and 80% for Model 1 and 2 respectively. Model 2
was subsequently used to create land cover classification and change
detection maps for all other years. Subtle changes and areas of
consistency (unchanged) were observed in the agricultural classes
and crop practices. Over the years as predicted by the land cover
classification. Forty one percent of the catchment comprised of
cereals with 35% possibly following a crop rotation system.
Vineyards largely remained constant with only one percent
conversion to vineyard from other land cover classes.
Abstract: Corrosion of concrete sewer pipes induced by
sulphuric acid attack is a recognised problem worldwide, which is not
only an attribute of countries with hot climate conditions as thought
before. The significance of this problem is by far only realised when
the pipe collapses causing surface flooding and other severe
consequences. To change the existing post-reactive attitude of
managing companies, easy to use and robust models are required to
be developed which currently lack reliable data to be correctly
calibrated. This paper focuses on laboratory experiments of
establishing concrete pipe corrosion rate by submerging samples in to
0.5pH sulphuric acid solution for 56 days under 10ºC, 20ºC and 30ºC
temperature regimes. The result showed that at very early stage of the
corrosion process the samples gained overall mass, at 30ºC the
corrosion progressed quicker than for other temperature regimes,
however with time the corrosion level for 10ºC and 20ºC regimes
tended towards those at 30ºC. Overall, at these conditions the
corrosion rates of 10 mm/year, 13,5 mm/year and 17 mm/year were
observed.
Abstract: We evaluate the performance of a numerical method
for global optimization of expensive functions. The method is using a
response surface to guide the search for the global optimum. This
metamodel could be based on radial basis functions, kriging, or a
combination of different models. We discuss how to set the cyclic
parameters of the optimization method to get a balance between local
and global search. We also discuss the eventual problem with Runge
oscillations in the response surface.
Abstract: Rehabilitation of dam components such as foundations, buttresses, spillways and overtopping protection require a wide range of construction and design methodologies. Geotechnical Engineering considerations play an important role in the design and construction of foundations of new dams. Much investigation is required to assess and evaluate the existing dams. The application of roller compacting concrete (RCC) has been accepted as a new method for constructing new dams or rehabilitating old ones. In the past 40 years there have been so many changes in the usage of RCC and now it is one of most satisfactory solutions of water and hydropower resource throughout the world. The considerations of rehabilitation and construction of dams might differ due to upstream reservoir and its influence on penetrating and dewatering of downstream, operations requirements and plant layout. One of the advantages of RCC is its rapid placement which allows the dam to be operated quickly. Unlike ordinary concrete it is a drier mix, and stiffs enough for compacting by vibratory rollers. This paper evaluates some different aspects of RCC and focuses on its preparation progress.
Abstract: Agro-industry is one of major industries that have
strong impacts on national economic incomes, growth, stability, and
sustainable development. Moreover, this industry also has strong
influences on social, cultural and political issues. Furthermore, this
industry, as producing primary and secondary products, is facing
challenges from such diverse factors such as demand inconsistency,
intense international competition, technological advancements and
new competitors. In order to maintain and to improve industry’s
competitiveness in both domestics and international markets, science
and technology are key factors. Besides hard sciences and
technologies, modern industrial engineering concepts such as Just in
Time (JIT) Total Quality Management (TQM), Quick Response
(QR), Supply Chain Management (SCM) and Lean can be very
effective to support to increase efficiency and effectiveness of these
agricultural products on world stage. Onion is one of Thailand’s
major export products which bring back national incomes. But, it is
also facing challenges in many ways. This paper focused its interests
in onion packing process and its related activities such as storage and
shipment from one of major packing plant and storage in Mae Wang
District, Chiang Mai, Thailand, by applying Toyota Production
System (TPS) or Lean concepts, to improve process capability
throughout the entire packing and distribution process which will be
profitable for the whole onion supply chain. And it will be beneficial
to other related agricultural products in Thailand and other ASEAN
countries.
Abstract: This work is the first dowel in a rather wide research
activity in collaboration with Euro Mediterranean Center for Climate
Changes, aimed at introducing scalable approaches in Ocean
Circulation Models. We discuss designing and implementation of
a parallel algorithm for solving the Variational Data Assimilation
(DA) problem on Graphics Processing Units (GPUs). The algorithm
is based on the fully scalable 3DVar DA model, previously proposed
by the authors, which uses a Domain Decomposition approach
(we refer to this model as the DD-DA model). We proceed with
an incremental porting process consisting of 3 distinct stages:
requirements and source code analysis, incremental development of
CUDA kernels, testing and optimization. Experiments confirm the
theoretic performance analysis based on the so-called scale up factor
demonstrating that the DD-DA model can be suitably mapped on
GPU architectures.
Abstract: Roadway planning and design is a very complex
process involving five key phases before a project is completed;
planning, project development, final design, right-of-way, and
construction. The planning phase for a new roadway transportation
project is a very critical phase as it greatly affects all latter phases of
the project. A location study is usually performed during the
preliminary planning phase in a new roadway project. The objective
of the location study is to develop alignment alternatives that are cost
efficient considering land acquisition and construction costs. This
paper describes a methodology to develop optimal preliminary
roadway alignments utilizing spatial-data. Four optimization criteria
are taken into consideration; roadway length, land cost, land slope,
and environmental impacts. The basic concept of the methodology is
to convert the proposed project area into a grid, which represents the
search space for an optimal alignment. The aforementioned
optimization criteria are represented in each of the grid’s cells. A
spatial-data optimization technique is utilized to find the optimal
alignment in the search space based on the four optimization criteria.
Two case studies for new roadway projects in Duval County in the
State of Florida are presented to illustrate the methodology. The
optimization output alignments are compared to the proposed Florida
Department of Transportation (FDOT) alignments. The comparison is
based on right-of-way costs for the alignments. For both case studies,
the right-of-way costs for the developed optimal alignments were
found to be significantly lower than the FDOT alignments.
Abstract: The structures obtained with the use of sandwich
technologies combine low weight with high energy absorbing
capacity and load carrying capacity. Hence, there is a growing and
markedly interest in the use of sandwiches with aluminum foam core
because of very good properties such as flexural rigidity and energy
absorption capability. In the current investigation, the static threepoint
bending tests were carried out on the sandwiches with
aluminum foam core and glass fiber reinforced polymer (GFRP)
skins at different values of support span distances aiming the analyses
of their flexural performance. The influence of the core thickness and
the GFRP skin type was reported in terms of peak load and energy
absorption capacity. For this purpose, the skins with two different
types of fabrics which have same thickness value and the aluminum
foam core with two different thicknesses were bonded with a
commercial polyurethane based flexible adhesive in order to combine
the composite sandwich panels. The main results of the bending tests
are: force-displacement curves, peak force values, absorbed energy,
collapse mechanisms and the effect of the support span length and
core thickness. The results of the experimental study showed that the
sandwich with the skins made of S-Glass Woven fabrics and with the
thicker foam core presented higher mechanical values such as load
carrying and energy absorption capacities. The increment of the
support span distance generated the decrease of the mechanical
values for each type of panels, as expected, because of the inverse
proportion between the force and span length. The most common
failure types of the sandwiches are debonding of the lower skin and
the core shear. The obtained results have particular importance for
applications that require lightweight structures with a high capacity
of energy dissipation, such as the transport industry (automotive,
aerospace, shipbuilding and marine industry), where the problems of
collision and crash have increased in the last years.
Abstract: A field study was conducted to evaluate the efficacy
of lavender for phytoremediation of contaminated soils. The
experiment was performed on an agricultural fields contaminated by
the Non-Ferrous-Metal Works near Plovdiv, Bulgaria. The
concentrations of Pb, Zn and Cd in lavender (roots, stems, leaves and
inflorescences) and in the essential oils of lavender were determined.
Lavender is a plant which is tolerant to heavy metals and can be
grown on contaminated soils, and which can be referred to the
hyperaccumulators of lead and the accumulators of cadmium and
zinc, and can be successfully used in the phytoremediation of heavy
metal contaminated soils. Favorable is also the fact that heavy metals
do not influence the development of the lavender, as well as on the
quality and quantity of the essential oil. The possibility of further
industrial processing will make lavender economically interesting
crops for farmers of phytoextraction technology.