Abstract: Complexation of anthocyanins to mimic natural
copigmentation process was investigated. Cyanidin-rich extracts from
Zea mays L. ceritina Kulesh. and delphinidin-rich extracts from
Clitoria ternatea L. were used to form 4 anthocyanin complexes,
AC1, AC2, AC3 and AC4, in the presence of several polyphenols and
a trace metal. Characterizations of the ACs were conducted by UV,
FTIR, DSC/TGA and morphological observations. Bathochromic
shifts of the UV spectra of 4 formulas of ACs were observed at peak
wavelengths of about 510-620 nm by 10 nm suggesting complex
formation. FTIR spectra of the ACs indicate shifts of peaks from
1,733 cm-1 to 1,696 cm-1 indicating interactions and a decrease in the
peak areas within the wavenumber of 3,400-3,500 cm-1 indicating
changes in hydrogen bonding. Thermal analysis of all of the ACs
suggests increases in melting temperature after complexation. AC
with the highest melting temperature was morphologically observed
by SEM and TEM to be crystal-like particles within a range of 50 to
200 nm. Particle size analysis of the AC by laser diffraction gave a
range of 50-600 nm, indicating aggregation. This AC was shown to
have no cytotoxic effect on cultured HGEPp0.5 and HGF (all p>
0.05) by MTT. Therefore, complexation of anthocyanins was simple
and self-assembly process, potentially resulting in nanosized particles
of anthocyanin complex.
Abstract: Anthocyanins are natural pigments with effective UV
protection but their topical use could be limited due to their
physicochemical characteristics. An attempt to overcome such
limitations by complexation of 2 major anthocyanin-rich sources, C.
ternatea and Z. mays, has potentiated its use as topical antiinflammatory.
Cell studies indicate no cytotoxicity of the
anthocyanin complex (AC) up to 1 mg/ml tested in HaCaT and
human fore head fibroblasts by MTT. Croton oil-induced ear edema
in Wistar rats suggests an effective dose of 5 mg/cm2 of AC as a
topical anti-inflammatory in comparison to 0.5 mg/cm2 of
fluocinolone acetonide. Niosomal encapsulation of the AC
significantly prolonged the anti-inflammatory activity particularly at
8 h after topical application (p = 0.0001). The AC was not cytotoxic
and its anti-inflammatory and activity was dose-dependent and
prolonged by niosomal encapsulation. It has also shown to promote
collagen type 1 production in cell culture. Thus, AC could be a
potential candidate for topical anti-inflammatory agent from natural
resources.
Abstract: Food is widely packaged with plastic materials to
prevent microbial contamination and spoilage. Ionizing radiation is
widely used to sterilize the food-packaging materials. Sterilization by
γ-radiation causes degradation such as embrittlement, stiffening,
softening, discoloration, odour generation, and decrease in molecular
weight. Many antioxidants can prevent γ-degradation but most of
them are toxic. The migration of antioxidants to its environment
gives rise to major concerns in case of food packaging plastics. In
this attempt, we have aimed to utilize synergistic mixtures of
stabilizers which are approved for food-contact applications.
Ethylene-propylene-diene terpolymer has been melt-mixed with
hindered amine stabilizers (HAS), phenolic antioxidants and organophosphites
(hydroperoxide decomposer). Results were discussed by
comparing the stabilizing efficiency of mixtures with and without
phenol system. Among phenol containing systems where we mostly
observed discoloration due to the oxidation of hindered phenol, the
combination of secondary HAS, tertiary HAS, organo-phosphite and
hindered phenol exhibited improved stabilization efficiency than
single or binary additive systems. The mixture of secondary HAS and
tertiary HAS, has shown antagonistic effect of stabilization.
However, the combination of organo-phosphite with secondary HAS,
tertiary HAS and phenol antioxidants have been found to give
synergistic even at higher doses of Gamma-irradiation. The effects
have been explained through the interaction between the stabilizers.
After γ-irradiation, the consumption of oligomeric stabilizer
significantly depends on the components of stabilization mixture. The
effect of the organo-phosphite antioxidant on the overall stability has
been discussed.
Abstract: Liver disorders are one of the major problems of the
world. Despite its frequent occurrence, high morbidity and high
mortality, its medical management is currently inadequate. This study
was designed to evaluate the hepatoprotective effect of saponin
extract of the root of Garcinia kola on the integrity of the liver of
paracetamol induced wistar albino rats. Twenty five (25) male adult
wistar albino rats were divided into five (5) groups. Group I was the
Control group that received distilled water only, group II was the
negative control that received 2 g/kg of paracetamol on the 13th day,
and group III, IV and V were pre-treated with 100, 200 and
400mg/kg of the saponin extract before inducing the liver damage on
the 13th day with 2 g/kg of paracetamol. Twenty four (24) h after
administration, the rats were sacrificed and blood samples were
collected. The serum Alanine Transaminase (ALT), Aspartate
Transaminase (AST), Alkaline Phosphatase (ALP) activities,
Bilirubin and conjugated bilirubin, glucose and protein
concentrations were evaluated. The liver was fixed immediately in
Formalin and was processed and stained in Haematoxylin and Eosin
(H&E). Administration of saponin extract from the root of Garcinia
kola significantly decreased paracetamol induced elevated enzymes
in the test group. Also histological observations showed that saponin
extract of the root of Garcinia kola exhibited a significant liver
protection against the toxicant as evident by the cells trying to return
to normal. Saponin extract from the root of Garcinia kola indicated a
protection of structural integrity of the hepatocytic cell membrane
and regeneration of the damaged liver.
Abstract: The rate of natural gas dissociation from the Coal
Matrix depends on depressurization of reservoir through removing of
the cleat water from the coal seam. These waters are similar to brine
and aged of very long years. For improving the connectivity through
fracking /fracturing, high pressure liquids are pumped off inside the
coal body. A significant quantity of accumulated water, a combined
mixture of cleat water and fracking fluids (back flow water) is
pumped out through gas well. In Queensland, Australia Coal Seam
Gas (CSG) industry is in booming state and estimated of 30,000 wells
would be active for CSG production forecasting life span of 30 years.
Integrated water management along with water softening programs is
practiced for subsequent treatment and later on discharge to nearby
surface water catchment. Water treatment is an important part of the
CSG industry. A case study on a CSG site and review on the test
results are discussed for assessing the Standards & Practices for
management of CSG by-product water and their subsequent disposal
activities. This study was directed toward (i) water management and
softening process in Spring Gully CSG field, (ii) Comparative
analysis on experimental study and standards and (iii) Disposal of the
treated water. This study also aimed for alternative usages and their
impact on vegetation, living species as well as long term effects.
Abstract: Rotary draw bending is a method which is being used
in tube forming. In the tube bending process, the neutral axis moves
towards the inner arc and the wall thickness distribution changes for
tube’s cross section. Thinning takes place in the outer arc of the tube
(extrados) due to the stretching of the material, whereas thickening
occurs in the inner arc of the tube (intrados) due to the comparison of
the material. The calculations of the wall thickness distribution,
neutral axis shifting, and strain distribution have not been accurate
enough, so far. The previous model (the geometrical model)
describes the neutral axis shifting and wall thickness distribution. The
geometrical of the tube, bending radius and bending angle are
considered in the geometrical model, while the influence of the
material properties of the tube forming are ignored. The advanced
model is a modification of the previous model using material
properties that depends on the correction factor. The correction factor
is a purely empirically determined factor. The advanced model was
compared with the Finite element simulation (FE simulation) using a
different bending factor (Bf =bending radius/ diameter of the tube),
wall thickness (Wf = diameter of the tube/ wall thickness), and
material properties (strain hardening exponent). Finite element model
of rotary draw bending has been performed in PAM-TUBE program
(version: 2012). Results from the advanced model resemble the FE
simulation and the experimental test.
Abstract: Content-based image retrieval (CBIR) uses the
contents of images to characterize and contact the images. This paper
focus on retrieving the image by separating images into its three color
mechanism R, G and B and for that Discrete Wavelet Transformation
is applied. Then Wavelet based Generalized Gaussian Density (GGD)
is practical which is used for modeling the coefficients from the
wavelet transforms. After that it is agreed to Histogram of Oriented
Gradient (HOG) for extracting its characteristic vectors with Relevant
Feedback technique is used. The performance of this approach is
calculated by exactness and it confirms that this method is wellorganized
for image retrieval.
Abstract: Composite materials, due to their unique properties
such as high strength to weight ratio, corrosion resistance, and impact
resistance have huge potential as structural materials in automotive,
construction and transportation applications. However, these
properties often come at higher cost owing to complex design
methods, difficult manufacturing processes and raw material cost.
Traditionally, tapered laminated composite structures are
manufactured using autoclave manufacturing process by ply drop off
technique. Autoclave manufacturing though very powerful suffers
from high capital investment and higher energy consumption. As per
the current trends in composite manufacturing, Out of Autoclave
(OoA) processes are looked as emerging technologies for
manufacturing the structural composite components for aerospace
and defense applications. However, there is a need for improvement
among these processes to make them reliable and consistent. In this
paper, feasibility of using out of autoclave process to manufacture the
variable thickness cantilever beam is discussed. The minimum weight
design for the composite beam is obtained using constant stress beam
concept by tailoring the thickness of the beam. Ply drop off
techniques was used to fabricate the variable thickness beam from
glass/epoxy prepregs. Experiments were conducted to measure
bending stresses along the span of the cantilever beam at different
intervals by applying the concentrated load at the free end.
Experimental results showed that the stresses in the bean at different
intervals were constant. This proves the ability of OoA process to
manufacture the constant stress beam. Finite element model for the
constant stress beam was developed using commercial finite element
simulation software. It was observed that the simulation results
agreed very well with the experimental results and thus validated
design and manufacturing approach used.
Abstract: A capacity spectrum method (CSM), one of methodologies to evaluate seismic fragilities of building structures, has been long recognized as the most convenient method, even if it contains several limitations to predict the seismic response of structures of interest. This paper proposes the procedure to estimate seismic fragility curves using an incremental dynamic analysis (IDA) rather than the method adopting a CSM. To achieve the research purpose, this study compares the seismic fragility curves of a 5-story reinforced concrete (RC) moment frame obtained from both methods; an IDA method and aCSM. Both seismic fragility curves are similar in slight and moderate damage states whereas the fragility curve obtained from the IDA method presents less variation (or uncertainties) in extensive and complete damage states. This is due to the fact that the IDA method can properly capture the structural response beyond yielding rather than the CSM and can directly calculate higher mode effects. From these observations, the CSM could overestimate seismic vulnerabilities of the studied structure in extensive or complete damage states.
Abstract: For cycling, the analysis of the pedal force is one of the
important factors in the study of exercise ability assessment and
overuse injuries. In past studies, a two-axis measurement sensor was
used at the sagittal plane to measure the force only in the anterior,
posterior, and vertical directions and to analyze the loss of force and
the injury on the frontal plane due to the forces in the right and left
directions. In this study, which is a basic study on diverse analyses of
the pedal force that consider the forces on the sagittal plane and the
frontal plane, a three-axis pedal force measurement sensor was
developed to measure the anterior-posterior (Fx), medio-lateral (Fz),
and vertical (Fy) forces. The sensor was fabricated with a size and
shape similar to those of the general flat pedal, and had a 550g weight
that allowed smooth pedaling. Its measurement range was ±1000 N for
Fx and Fz and ±2000 N for Fy, and its non-linearity, hysteresis, and
repeatability were approximately 0.5%. The data were sampled at
1000 Hz using a signal collector. To use the developed sensor, the
pedaling efficiency (index of efficiency, IE) and the range of left and
right (medio-lateral, ML) forces were measured with two seat heights
(low and high). The results of the measurement showed that the IE was
higher and the force range in the ML direction was lower with the high
position than with the low position. The developed measurement
sensor and its application results will be useful in understanding and
explaining the complicated pedaling technique, and will enable
diverse kinematic analyses of the pedal force on the sagittal plane and
the frontal plane.
Abstract: The effect of the inclusion of thyme and rosemary
essential oils into chitosan films, as well as the microbiological and
physical properties when storing chitosan film with and without the
mentioned inclusion was studied. The film forming solution was
prepared by dissolving chitosan (2%, w/v), polysorbate 80 (4% w/w
CH) and glycerol (16% w/w CH) in aqueous lactic acid solutions
(control). The thyme (TEO) and rosemary (REO) essential oils (EOs)
were included 1:1 w/w (EOs:CH) on their combination 50/50
(TEO:REO). The films were stored at temperatures of 5, 20, 33°C
and a relative humidity of 75% during four weeks. The films with
essential oil inclusion did not show an antimicrobial activity against
strains. This behavior could be explained because the chitosan only
inhibits the growth of microorganisms in direct contact with the
active sites. However, the inhibition capacity of TEO was higher than
the REO and a synergic effect between TEO:REO was found for S.
enteritidis strains in the chitosan solution.
Some physical properties were modified by the inclusion of
essential oils. The addition of essential oils does not affect the
mechanical properties (tensile strength, elongation at break, puncture
deformation), the water solubility, the swelling index nor the DSC
behavior. However, the essential oil inclusion can significantly
decrease the thickness, the moisture content, and the L* value of
films whereas the b* value increased due to molecular interactions
between the polymeric matrix, the loosing of the structure, and the
chemical modifications. On the other hand, the temperature and time
of storage changed some physical properties on the chitosan films.
This could have occurred because of chemical changes, such as
swelling in the presence of high humidity air and the reacetylation of
amino groups. In the majority of cases, properties such as moisture
content, tensile strength, elongation at break, puncture deformation,
a*, b*, chrome, 7E increased whereas water resistance, swelling
index, L*, and hue angle decreased.
Abstract: The design, manufacture, and operation of thin-walled
pressure vessels must be based on maximum safe operating pressure
and an adequate factor of safety (FoS). This research paper first
reports experimental evaluation of longitudinal and hoops stresses
based on working pressure as well as maximum pressure; and then
includes a critical study of factor of safety (FoS) in the design of a
glass fiber pressure vessel. Experimental work involved the use of
measuring instruments and the readings from pressure gauges.
Design calculations involved the computations of design stress and
FoS; the latter was based on breaking strength of 55 MPa for the
glass fiber (pressure-vessel material). The experimentally determined
FoS value has been critically compared with the general FoS allowed
in the design of glass fiber pressure vessels.
Abstract: Batteries of electric vehicles (BEV) are becoming
more attractive with the advancement of new battery technologies
and promotion of electric vehicles. BEV batteries are recharged on
board vehicles using either the grid (G2V for Grid to Vehicle) or
renewable energies in a stand-alone application (H2V for Home to
Vehicle). This paper deals with the modeling, sizing and control of a
photovoltaic stand-alone application that can charge the BEV at
home. The modeling approach and developed mathematical models
describing the system components are detailed. Simulation and
experimental results are presented and commented.
Abstract: To date, one of the few comprehensive indicators for
the measurement of food security is the Global Food Security Index
(GFSI). This index is a dynamic quantitative and qualitative
benchmarking model, constructed from 28 unique indicators, that
measures drivers of food security across both developing and
developed countries. Whereas the GFSI has been calculated across a
set of 109 countries, in this paper we aim to present and compare, for
the Middle East and North Africa (MENA), 1) the Food Security
Index scores achieved and 2) the data available on affordability,
availability, and quality of food. The data for this work was taken
from the latest available report published by the creators of the GFSI,
which in turn used information from national and international
statistical sources. MENA countries rank from place 17/109 (Israel,
although with resent political turmoil this is likely to have changed)
to place 91/109 (Yemen) with household expenditure spent in food
ranging from 15.5% (Israel) to 60% (Egypt). Lower spending on food
as a share of household consumption in most countries and better
food safety net programs in the MENA have contributed to a notable
increase in food affordability. The region has also, however,
experienced a decline in food availability, owing to more limited
food supplies and higher volatility of agricultural production. In
terms of food quality and safety the MENA has the top ranking
country (Israel). The most frequent challenges faced by the countries
of the MENA include public expenditure on agricultural research and
development as well as volatility of agricultural production. Food
security is a complex phenomenon that interacts with many other
indicators of a country’s wellbeing; in the MENA it is slowly but
markedly improving.
Abstract: This paper presents analysis and design of a wideband
Wilkinson power divider for wireless applications. The design is
accomplished by transforming the lengths and impedances of the
quarter wavelength sections of the conventional Wilkinson power
divider into U-shaped sections. The designed power divider is
simulated by using ADS Agilent technologies and CST microwave
studio software. It is shown that the proposed power divider has
simple topology and good performances in terms of insertion loss,
port matching and isolation at all operating frequencies (1.8 GHz,
2.45 GHz and 3.55 GHz).
Abstract: This paper presents the development of a single-ended 38.5 kS/s 10-bit programmable reference SAR ADC which is realized in MIMOS’s 0.35 µm CMOS process. The design uses a resistive DAC, a dynamic comparator with pre-amplifier and a SAR digital logic to create 10 effective bits ADC. A programmable reference circuitry allows the ADC to operate with different input range from 0.6 V to 2.1 V. The ADC consumed less than 7.5 mW power with a 3 V supply.
Abstract: A thermosyphon system is a heat transfer loop which
operates on the basis of gravity and buoyancy forces. It guarantees a
good reliability and low maintenance cost as it does not involve any
mechanical pump. Therefore, it can be used in many industrial
applications such as refrigeration and air conditioning, electronic
cooling, nuclear reactors, geothermal heat extraction, etc. But flow
instabilities and loop configuration are the major problems in this
system. Several previous researchers studied that stabilities can be
suppressed by using nanofluids as loop fluid. In the present study a
rectangular thermosyphon loop with end heat exchangers are
considered for the study. This configuration is more appropriate for
many practical applications such as solar water heater, geothermal
heat extraction, etc. In the present work, steady-state analysis is
carried out on thermosyphon loop with parallel flow coaxial heat
exchangers at heat source and heat sink. In this loop nanofluid is
considered as the loop fluid and water is considered as the external
fluid in both hot and cold heat exchangers. For this analysis onedimensional
homogeneous model is developed. In this model,
conservation equations like conservation of mass, momentum, energy
are discretized using finite difference method. A computer code is
written in MATLAB to simulate the flow in thermosyphon loop. A
comparison in terms of heat transfer is made between water and
nanofluid as working fluids in the loop.
Abstract: A Distributed Denial of Service (DDoS) attack is a
major threat to cyber security. It originates from the network layer or
the application layer of compromised/attacker systems which are
connected to the network. The impact of this attack ranges from the
simple inconvenience to use a particular service to causing major
failures at the targeted server. When there is heavy traffic flow to a
target server, it is necessary to classify the legitimate access and
attacks. In this paper, a novel method is proposed to detect DDoS
attacks from the traces of traffic flow. An access matrix is created
from the traces. As the access matrix is multi dimensional, Principle
Component Analysis (PCA) is used to reduce the attributes used for
detection. Two classifiers Naive Bayes and K-Nearest neighborhood
are used to classify the traffic as normal or abnormal. The
performance of the classifier with PCA selected attributes and actual
attributes of access matrix is compared by the detection rate and
False Positive Rate (FPR).
Abstract: Vertical Handover(VHO) among different
communication technologies ensuring uninterruption and service
continuity is one of the most important performance parameter in
Heterogenous networks environment. In an integrated Universal
Mobile Telecommunicatin System(UMTS) and Wireless Local
Area Network(WLAN), WLAN is given an inherent priority over
UMTS because of its high data rates with low cost. Therefore
mobile users want to be associated with WLAN maximum of the
time while roaming, to enjoy best possible services with low cost.
That encourages reduction of number of VHO. In this work the
reduction of number of VHO with respect to varying number of
WLAN Access Points(APs) in an integrated UMTS and WLAN
network is investigated through simulation to provide best possible
cost effective service to the users. The simulation has been carried
out for an area (7800 × 9006)m2 where COST-231 Hata model
and 3GPP (TR 101 112 V 3.1.0) specified models are used for
WLAN and UMTS path loss models respectively. The handover
decision is triggered based on the received signal level as compared
to the fade margin. Fade margin gives a probabilistic measure of
the reliability of the communication link. A relationship between
number of WLAN APs and the number of VHO is also established
in this work.
Abstract: In this paper, the transient device performance analysis
of n-type Gate Inside JunctionLess Transistor (GI-JLT) has been
evaluated. 3-D Bohm Quantum Potential (BQP) transport device
simulation has been used to evaluate the delay and power dissipation
performance. GI-JLT has a number of desirable device parameters
such as reduced propagation delay, dynamic power dissipation,
power and delay product, intrinsic gate delay and energy delay
product as compared to Gate-all-around transistors GAA-JLT. In
addition to this, various other device performance parameters namely,
on/off current ratio, short channel effects (SCE), transconductance
Generation Factor (TGF) and unity gain cut-off frequency (fT ) and
subthreshold slope (SS) of the GI-JLT and GAA-JLT have been
analyzed and compared. GI-JLT shows better device performance
characteristics than GAA-JLT for low power and high frequency
applications, because of its larger gate electrostatic control on the
device operation.