Abstract: The reheating furnace is used to reheat the steel slabs
before the hot-rolling process. The supported system includes the
stationary/moving beams, and the skid buttons which block some
thermal radiation transmitted to the bottom of the slabs. Therefore, it is
important to analyze the steel slab temperature distribution during the
heating period. A three-dimensional mathematical transient heat
transfer model for the prediction of temperature distribution within the
slab has been developed. The effects of different skid button height
(H=60mm, 90mm, and 120mm) and different gap distance between
two slabs (S=50mm, 75mm, and 100mm) on the slab skid mark
formation and temperature profiles are investigated. Comparison with
the in-situ experimental data from Steel Company in Taiwan shows
that the present heat transfer model works well for the prediction of
thermal behavior of the slab in the reheating furnace. It is found that
the skid mark severity decreases with an increase in the skid button
height. The effect of gap distance is important only for the slab edge
planes, while it is insignificant for the slab central planes.
Abstract: This paper presents the influence of the vertical
seismic component on the non-linear dynamics analysis of three
different structures. The subject structures were analyzed and
designed according to recent codes. This paper considers three types
of buildings: 5-, 10-, and 15-story buildings. The non-linear
dynamics analysis of the structures with assuming elastic-perfectlyplastic
behavior was performed using RAM PERFORM-3D software;
the horizontal component was taken into consideration with and
without the incorporation of the corresponding vertical component.
Dynamic responses obtained for the horizontal component acting
alone were compared with those obtained from the simultaneous
application of both seismic components. The results show that the
effect of the vertical component of ground motion may increase the
axial load significantly in the interior columns and, consequently, the
stories. The plastic mechanisms would be changed. The P-Delta
effect is expected to increase. The punching base plate shear of the
columns should be considered. Moreover, the vertical component
increases the input energy when the structures exhibit inelastic
behavior and are taller.
Abstract: Wicking and evaporation of water in porous knitted fabrics is investigated by combining experimental and analytical approaches: The standard wicking model from Lucas and Washburn is enhanced to account for evaporation and gravity effects. The goal is to model the effect of gravity and evaporation on wicking using simple analytical expressions and investigate the influence of fabrics geometrical parameters, such as porosity and thickness on evaporation impact on maximum reachable height values. The results show that fabric properties have a significant influence on evaporation effect. In this paper, an experimental study of determining water kinetics from different knitted fabrics were gravimetrically investigated permitting the measure of the mass and the height of liquid rising in fabrics in various atmospheric conditions. From these measurements, characteristic pore parameters (capillary radius and permeability) can be determined.
Abstract: Red pepper (Capsicum annum L.) has long been
recognized as a good source of antioxidants, being rich in ascorbic
acid and other phytochemicals. In Turkish cuisine red pepper is
sometimes consumed raw in salads and baked as a garnish, but its
most wide consumption type is red pepper paste. The processing of
red pepper into pepper paste includes various thermal treatment steps
such as heating and pasteurizing. There are reports demonstrating an
enhancement or reduction in antioxidant activity of vegetables after
thermal treatment. So this study was conducted to investigate the
total phenolic, ascorbic acid and total carotenoids as well as free
radical scavenging activity of raw red pepper and various red pepper
pastes obtainable on the market. The samples were analyzed for
radical-scavenging activity (RSA) and total polyphenol (TP) content
using 1,1-diphenyl-2-picrylhydrazyl (DPPH) and Folin-Ciocalteu
methods, respectively. Total carotenoids and ascorbic acid contents
were determined spectrophotometrically. Results suggest that hot
pepper paste contained significantly (P0.05) difference in RSA, ascorbic acid and total carotenoids
content between sweet and hot red pepper paste products. It is
concluded that the red pepper paste, that has a wide range of
consumption in Turkish cuisine, presents a good dose of phenolic
compounds and antioxidant capacity and it should be regarded as a
functional food.
Abstract: An integrated modeling approach was used in this study for energy planning and climate change mitigation assessment. The main objective of this study was to develop various green-house gas (GHG) mitigations scenarios in the energy demand and supply sectors for the state of Florida. The Long range energy alternative planning (LEAP) model was used in this study to examine the energy alternative and GHG emissions reduction scenarios for short and long term (2010-2050). One of the energy analysis and GHG mitigation scenarios was developed by taking into account the available renewable energy resources potential for power generation in the state of Florida. This will help to compare and analyze the GHG reduction measure against “Business As Usual” and ‘State of Florida Policy” scenarios. Two master scenarios: “Electrification” and “Energy efficiency and Lifestyle” were developed through combination of various mitigation scenarios: technological changes and energy efficiency and conservation. The results show a net reduction of the energy demand and GHG emissions by adopting these two energy scenarios compared to the business as usual.
Abstract: A large variety of pipe flange is required in marine
and construction industry. Pipe flanges are usually welded or screwed
to the pipe end and are connected with bolts. This approach is very
simple and widely used for a long time; however, it results in high
development cost and low productivity, and the productions made by
this approach usually have safety problem at the welding area. In this
research, a new approach of forming pipe flange based on cold
forging and floating die concept is presented. This innovative
approach increases the effectiveness of the material usage and save
the time cost compared with conventional welding method. To ensure the dimensional accuracy of the final product, the finite
element analysis (FEA) was carried out to simulate the process of
cold forging, and the orthogonal experiment methods were used to
investigate the influence of four manufacturing factors (pin die angle,
pipe flange angle, rpm, pin die distance from clamp jig) and predicted
the best combination of them. The manufacturing factors were
obtained by numerical and experimental studies and it shows that the
approach is very useful and effective for the forming of pipe flange,
and can be widely used later.
Abstract: Growing human population has placed increased
demands on water supplies and spurred a heightened interest in
desalination infrastructure. Key elements of the economics of
desalination projects are thermal and electrical inputs. With growing
concerns over use of fossil fuels to (indirectly) supply these inputs,
coupling of desalination with nuclear power production represents a
significant opportunity. Individually, nuclear and desalination
technologies have a long history and are relatively mature. For
desalination, Reverse Osmosis (RO) has the lowest energy inputs.
However, the economically driven output quality of the water
produced using RO, which uses only electrical inputs, is lower than the
output water quality from thermal desalination plants. Therefore,
modern desalination projects consider that RO should be coupled with
thermal desalination technologies (MSF, MED, or MED-TVC) with
attendant steam inputs to permit blending to produce various qualities
of water. A large nuclear facility is well positioned to dispatch large
quantities of both electrical and thermal power. This paper considers
the supply of thermal energy to a large desalination facility to examine
heat balance impact on the nuclear steam cycle. The APR1400 nuclear
plant is selected as prototypical from both a capacity and turbine cycle
heat balance perspective to examine steam supply and the impact on
electrical output. Extraction points and quantities of steam are
considered parametrically along with various types of thermal
desalination technologies to form the basis for further evaluations of
economically optimal approaches to the interface of nuclear power
production with desalination projects. In our study, the
thermodynamic evaluation will be executed by DE-TOP, an IAEA
sponsored program. DE-TOP has capabilities to analyze power
generation systems coupled to desalination plants through various
steam extraction positions, taking into consideration the isolation loop
between the nuclear and the thermal desalination facilities (i.e., for
radiological isolation).
Abstract: The market competition is moving from the single
firm to the whole supply chain because of increasing competition and
growing need for operational efficiencies and customer orientation.
Supply chain management allows companies to look beyond their
organizational boundaries to develop and leverage resources and
capabilities of their supply chain partners. This creates competitive
advantages in the marketplace and because of this SCM has acquired
strategic importance. Lean Approach is a management strategy that focuses on reducing
every type of waste present in an organization. This approach is
becoming more and more popular among supply chain managers. The supply chain application of lean approach is not frequent. In
particular, it is not well studied which are the impacts of lean
approach principles in a supply chain context. In literature there are
only few studies aimed at understanding the qualitative impact of the
lean approach in supply chains. Therefore, the goal of this research
work is to study the impacts of lean principles implementation along
a supply chain. To achieve this, a simulation model of a threeechelon
multi-product supply chain has been built. Kanban system (and several priority policies) and setup time
reduction degrees are implemented in the lean-configured supply
chain to apply pull and lot-sizing decrease principles respectively. To
evaluate the benefits of lean approach, lean supply chain is compared
with an EOQ-configured supply chain. The simulation results show
that Kanban system and setup-time reduction improve inventory
stock level. They also show that logistics efforts are affected to lean
implementation degree. The paper concludes describing
performances of lean supply chain in different contexts.
Abstract: Optimizing the parameters in the controller plays a
vital role in the control theory and its applications. Optimizing the
PID parameters is finding out the best value from the feasible
solutions. Finding the optimal value is an optimization problem.
Inverted Pendulum is a very good platform for control engineers to
verify and apply different logics in the field of control theory. It is
necessary to find an optimization technique for the controller to tune
the values automatically in order to minimize the error within the
given bounds. In this paper, the algorithmic concepts of Harmony
search (HS) and Genetic Algorithm (GA) have been analyzed for the
given range of values. The experimental results show that HS
performs well than GA.
Abstract: Objectives: To determine the nutritional status and
risk factors associated with women practicing geophagia in QwaQwa,
South Africa. Materials and Methods: An observational epidemiological study
design was adopted which included an exposed (geophagia) and nonexposed
(control) group. A food frequency questionnaire, anthropometric measurements and blood sampling were applied to
determine nutritional status of participants. Logistic regression
analysis was performed in order to identify factors that were likely to
be associated with the practice of geophagia. Results: The mean total energy intake for the geophagia group (G)
and control group (C) were 10324.31 ± 2755.00 kJ and 10763.94 ±
2556.30 kJ respectively. Both groups fell within the overweight
category according to the mean Body Mass Index (BMI) of each
group (G= 25.59 kg/m2; C= 25.14 kg/m2). The mean serum iron
levels of the geophagia group (6.929 μmol/l) were significantly lower
than that of the control group (13.75 μmol/l) (p = 0.000). Serum
transferrin (G=3.23g/l; C=2.7054g/l) and serum transferrin saturation
(G=8.05%; C=18.74%) levels also differed significantly between
groups (p=0.00). Factors that were associated with the practice of
geophagia included haemoglobin (Odds ratio (OR):14.50), serumiron
(OR: 9.80), serum-ferritin (OR: 3.75), serum-transferrin (OR:
6.92) and transferrin saturation (OR: 14.50). A significant negative
association (p=0.014) was found between women who were wageearners
and those who were not wage-earners and the practice of
geophagia (OR: 0.143; CI: 0.027; 0.755). These findings seem to
indicate that a permanent income may decrease the likelihood of
practising geophagia. Key Findings: Geophagia was confirmed to be a risk factor for
iron deficiency in this community. The significantly strong
association between geophagia and iron deficiency emphasizes the
importance of identifying the practice of geophagia in women,
especially during their child bearing years.
Abstract: Zinc borate is an important inorganic hydrate borate
material, which can be used as a flame retardant agent and corrosion
resistance material. This compound can loss its structural water
content at higher than 290°C. Due to thermal stability; Zinc Borate
can be used as flame retardant at high temperature process of plastic
and gum. In this study, the ultrasonic reaction of zinc borates were
studied using hydrozincite (Zn5(CO3)2·(OH)6) and boric acid
(H3BO3) raw materials. Before the synthesis raw materials were
characterized by X-Ray Diffraction (XRD) and Fourier Transform
Infrared Spectroscopy (FT-IR). Ultrasonic method is a new
application on the zinc borate synthesis. The synthesis parameters
were set to 90°C reaction temperature and 55 minutes of reaction
time, with 1:1, 1:2, 1:3, 1:4 and 1:5 molar ratio of starting materials
(Zn5(CO3)2·(OH)6 : H3BO3). After the zinc borate synthesis, the
products were analyzed by XRD and FT-IR. As a result, optimum
molar ratio of 1:5 is determined for the synthesis of zinc borates with
ultrasonic method.
Abstract: This work deals with the problem of MHD mixed
convection in a completely porous and differentially heated vertical
channel. The model of Darcy-Brinkman-Forchheimer with the
Boussinesq approximation is adopted and the governing equations are
solved by the finite volume method. The effects of magnetic field and
buoyancy force intensities are given by the Hartmann and Richardson
numbers respectively, as well as the Joule heating represented by
Eckert number on the velocity and temperature fields, are examined.
The main results show an augmentation of heat transfer rate with the
decrease of Darcy number and the increase of Ri and Ha when Joule
heating is neglected.
Abstract: The research explores the relationship between
management responsibility and corporate governance of listed
companies in Kazakhstan. This research employs firm level data of
selected listed non-financial firms and firm level data “operational”
financial sector, consisted from banking sector, insurance companies
and accumulated pension funds using multivariate regression analysis
under fixed effect model approach. Ownership structure includes
institutional ownership, managerial ownership and private investor’s
ownership. Management responsibility of the firm is expressed by the
decision of the firm on amount of leverage. Results of the cross
sectional panel study for non-financial firms showed that only
institutional shareholding is significantly negatively correlated with
debt to equity ratio. Findings from “operational” financial sector
show that leverage is significantly affected only by the CEO/Chair
duality and the size of financial institutions, and insignificantly
affected by ownership structure. Also, the findings show, that there is
a significant negative relationship between profitability and the debt
to equity ratio for non-financial firms, which is consistent with
pecking order theory. Generally, the found results suggest that
corporate governance and a management responsibility play
important role in corporate performance of listed firms in
Kazakhstan.
Abstract: Radical technological innovations enable companies
to reach strong market positions and are thus desirable. On the other
hand, the innovation process is related to significant costs and risks.
Hence, the knowledge of the factors that influence success is crucial
for technology driven companies. Taking a previously developed
framework of Critical Success Factors for radical technological
innovations as a reference model, we conducted a structured and
focused literature review of eleven standard books within the field of
technology and innovation management. With this approach we aim
to evaluate, expand, and clarify the set of Critical Success Factors
detailed in this framework. Overall, the set of factors and their
allocation to the main categories of the framework could be
confirmed. However, the factor organizational home is not
emphasized and discussed in most of the reviewed literature. On the
other hand, an additional factor that has not been part of the
framework is described to be important – strategy fit. Furthermore,
the factors strategic alliances and platform strategy appear in the
literature but in a different context compared to the reference model.
Abstract: In this paper, various methods of providing restricted
earth fault protection are discussed. The proper operation of high and
low impedance Restricted Earth Fault (REF) protection for various
applications has been discussed. The maloperation of a relay due to
improper placement of CTs has been identified and a simple/unique
solution has been proposed in this work with a case study. Moreover,
it is found that the proper placement of CT in high impedance method
will provide the same result with reduced CT. This methodology has
been successfully implemented in Al Takreer refinery for a 2000
KVA transformer. The outcome of the paper may be included in
IEEEC37.91 standard to give the proper guidance for protection
engineers to sort out the issues related to mal functioning of REF
relays.
Abstract: The effects of wood ash from five common tropical
woods on the ignition point of four common tropical woods in
Nigeria were investigated. The ash and moisture contents of the wood
sawdust from Mahogany (Khaya ivorensis), Opepe (Sarcocephalus
latifolius), Abura (Mitragyna ciliata), Rubber (Heavea brasilensis)
and Poroporo (Sorghum bicolour) used, were determined using a
furnace (Vecstar furnaces, model ECF2, serial no. f3077) and oven
(Genlab laboratory oven, model MINO/040) respectively. The metal
contents of the five wood sawdust ash samples were determined
using a Perkin Elmer optima 3000 dv atomic absorption spectrometer
while the ignition points were determined using Vecstar furnaces
model ECF2. Poroporo had the highest ash content, 2.263g while
rubber had the least, 0.710g. The results for the moisture content
range from 2.971g to 0.903g. Magnesium metal had the highest
concentration of all the metals, in all the wood ash samples; with
mahogany ash having the highest concentration, 9.196ppm while
rubber ash had the least concentration of magnesium metal, 2.196
ppm. The ignition point results showed that the wood ashes from
mahogany and opepe increased the ignition points of the test wood
samples, Danta (Nesogordonia papaverifera), Ekpaya, Akomu
(Pycnanthus angolensis) and Oleku when coated on them while the
ashes from poroporo, rubber and abura decreased the ignition points
of the test wood samples when coated on them. However, Opepe saw
dust ash decreased the ignition point in one of the test wood samples,
suggesting that the metal content of the test wood sample was more
than that of the Opepe saw dust ash. Therefore, Mahogany and Opepe
saw dust ashes could be used in the surface treatment of wood to
enhance their fire resistance or retardancy. However, the caution to
be exercised in this application is that the metal content of the test
wood samples should be evaluated as well.
Abstract: This paper highlights an innovative and nontraditional
violence prevention program that is making a noticeable impact in
what was once one of the country’s most violent communities. With
unique and tailored strategies, the Operation Peacemaker Fellowship,
established in Richmond, California, combines components of
evidence-based practices with a community-oriented focus on
relationships and mentoring to fill a gap in services and increase
community safety. In an effort to highlight these unique strategies
and provide a blueprint for other communities with violent crime
problems, the authors of this paper hope to clearly delineate how one
community is moving forward with vanguard approaches to invest in
the lives of young men who once were labeled their community’s
most violent, even most deadly, youth. The impact of this program is
evidenced through the fellows’ own voices as they illuminate the
experience of being in the Fellowship. In interviews, fellows describe
how participating in this program has transformed their lives and the
lives of those they love. The authors of this article spent more than
two years researching this Fellowship program in order to conduct an
evaluation of it and, ultimately, to demonstrate how this program is a
testament to the power of relationships and love combined with
evidence-based practices, consequently enriching the lives of youth
and the community that embraces them.
Abstract: The photovoltaic (PV) panel with no galvanic
isolation system is well known technique in the world which is
effective and delivers power with enhanced efficiency. The PV
generation presented here is for stand-alone system installed in
remote areas when as the resulting power gets connected to electronic
load installation instead of being tied to the grid. Though very small,
even then transformer-less topology is shown to be with leakage in
pico-ampere range. By using PWM technique PWM, leakage current
in different situations is shown. The results shown in this paper show
how the pico-ampere current is reduced to femto-ampere through use
of inductors and capacitors of suitable values of inductor and
capacitors with the load.
Abstract: Developing our knowledge of when pineapple roots
grow can lead to improved water, fertilizer applications, and more
precise culture management. This paper presents current
understanding of morphological traits in pineapple roots, highlighting
studies using incubation periods and various solid MS media treated
with different sucrose concentrations and pH, which directly assess in
vitro environmental factors. Rooting parameters had different optimal
sucrose concentrations and incubation periods. All shoots failed to
root in medium supplemented with sucrose at 5 g/L and no roots
formed within the first 45 days in medium enriched with sucrose at
10 g/L. After 75 days, all shoots rooted in medium enriched with 10
and 20 g/L sucrose. Moreover, MS medium supplied with 20 g/L
sucrose resulted in the longest and the highest number of roots with
27.3 mm and 4.7, respectively. Root function, such as capacity for P
and N uptake, declined rapidly with root length. As a result, the
longer the incubation period, the better the rooting responses would
be.
Abstract: This study and the field test comparisons were carried
out on the Algerian Derguna – Setif transmission systems. The
transmission line of normal voltage 225 kV is 65 km long,
transported and uses twin bundle conductors protected with two
shield wires of transposed galvanized steel. An iterative finite-element method is used to solve Poisons
equation. Two algorithms are proposed for satisfying the current
continuity condition and updating the space-charge density. A new approach to the problem of corona discharge in
transmission system has been described in this paper. The effect of
varying the configurations and wires number is also investigated. The
analysis of this steady is important in the design of HVDC
transmission lines. The potential and electric field have been
calculating in locations singular points of the system.