Abstract: The purpose of suspension system in automobiles is to
improve the ride comfort and road handling. In this research the ride
and handling performance of a specific automobile with passive
suspension system is compared to a proposed fuzzy logic semi active
suspension system designed for that automobile. The bodysuspension-
wheel system is modeled as a two degree of freedom
quarter car model. MATLAB/SIMULINK [1] was used for
simulation and controller design. The fuzzy logic controller is based
on two inputs namely suspension velocity and body velocity. The
output of the fuzzy controller is the damping coefficient of the
variable damper. The result shows improvement over passive
suspension method.
Abstract: Fault tolerance is critical in many of today's large computer systems. This paper focuses on improving fault tolerance through testing. Moreover, it concentrates on the memory faults: how to access the editable part of a process memory space and how this part is affected. A special Software Fault Injection Technique (SFIT) is proposed for this purpose. This is done by sequentially scanning the memory of the target process, and trying to edit maximum number of bytes inside that memory. The technique was implemented and tested on a group of programs in software packages such as jet-audio, Notepad, Microsoft Word, Microsoft Excel, and Microsoft Outlook. The results from the test sample process indicate that the size of the scanned area depends on several factors. These factors are: process size, process type, and virtual memory size of the machine under test. The results show that increasing the process size will increase the scanned memory space. They also show that input-output processes have more scanned area size than other processes. Increasing the virtual memory size will also affect the size of the scanned area but to a certain limit.
Abstract: We investigate sonic cues for binaural sound localization within classrooms and present a structural model for the same. Two of the primary cues for localization, interaural time difference (ITD) and interaural level difference (ILD) created between the two ears by sounds from a particular point in space, are used. Although these cues do not lend any information about the elevation of a sound source, the torso, head, and outer ear carry out elevation dependent spectral filtering of sounds before they reach the inner ear. This effect is commonly captured in head related transfer function (HRTF) which aids in resolving the ambiguity from the ITDs and ILDs alone and helps localize sounds in free space. The proposed structural model of HRTF produces well controlled horizontal as well as vertical effects. The implemented HRTF is a signal processing model which tries to mimic the physical effects of the sounds interacting with different parts of the body. The effectiveness of the method is tested by synthesizing spatial audio, in MATLAB, for use in listening tests with human subjects and is found to yield satisfactory results in comparison with existing models.
Abstract: Spatial outliers in remotely sensed imageries represent
observed quantities showing unusual values compared to their
neighbor pixel values. There have been various methods to detect the
spatial outliers based on spatial autocorrelations in statistics and data
mining. These methods may be applied in detecting forest fire pixels
in the MODIS imageries from NASA-s AQUA satellite. This is
because the forest fire detection can be referred to as finding spatial
outliers using spatial variation of brightness temperature. This point is
what distinguishes our approach from the traditional fire detection
methods. In this paper, we propose a graph-based forest fire detection
algorithm which is based on spatial outlier detection methods, and test
the proposed algorithm to evaluate its applicability. For this the
ordinary scatter plot and Moran-s scatter plot were used. In order to
evaluate the proposed algorithm, the results were compared with the
MODIS fire product provided by the NASA MODIS Science Team,
which showed the possibility of the proposed algorithm in detecting
the fire pixels.
Abstract: Fluency is a skill that, unfortunately, many students
lack. This deficiency causes students to be frustrated with, and
overwhelmed by, the act of reading. However, research suggests that
the repeated reading method may help students to improve their
fluency. This study examines the effects of repeated readings on
student fluency. The study-s overarching question is: What effect do
increases in repeated reading have on reading fluency among middle
school students from diverse backgrounds? More specifically, the
authors examine whether repeated reading improves the fluency,
reading speed, reading-oriented self-esteem, and confidence of
students of diverse academic abilities, socio-economics statuses, and
racial and ethnic backgrounds. To examine these questions the
authors conducted a study using repeated reading strategies with a
sample of students from an urban, middle school in the southeastern
United States. We found that, on average, the use of repeated reading
strategies increased students- fluency, words per minute (wpm)
reading score, reading-oriented self-esteem, and confidence.
Abstract: Reliable water level forecasts are particularly
important for warning against dangerous flood and inundation. The
current study aims at investigating the suitability of the adaptive
network based fuzzy inference system for continuous water level
modeling. A hybrid learning algorithm, which combines the least
square method and the back propagation algorithm, is used to
identify the parameters of the network. For this study, water levels
data are available for a hydrological year of 2002 with a sampling
interval of 1-hour. The number of antecedent water level that should
be included in the input variables is determined by two statistical
methods, i.e. autocorrelation function and partial autocorrelation
function between the variables. Forecasting was done for 1-hour until
12-hour ahead in order to compare the models generalization at
higher horizons. The results demonstrate that the adaptive networkbased
fuzzy inference system model can be applied successfully and
provide high accuracy and reliability for river water level estimation.
In general, the adaptive network-based fuzzy inference system
provides accurate and reliable water level prediction for 1-hour ahead
where the MAPE=1.15% and correlation=0.98 was achieved. Up to
12-hour ahead prediction, the model still shows relatively good
performance where the error of prediction resulted was less than
9.65%. The information gathered from the preliminary results
provide a useful guidance or reference for flood early warning
system design in which the magnitude and the timing of a potential
extreme flood are indicated.
Abstract: The orthogonal processes to shape the triangle steel plate into a equilateral vertical steel are examined by an incremental elasto-plastic finite-element method based on an updated Lagrangian formulation. The highly non-linear problems due to the geometric changes, the inelastic constitutive behavior and the boundary conditions varied with deformation are taken into account in an incremental manner. On the contact boundary, a modified Coulomb friction mode is specially considered. A weighting factor r-minimum is employed to limit the step size of loading increment to linear relation. In particular, selective reduced integration was adopted to formulate the stiffness matrix. The simulated geometries of verticality could clearly demonstrate the vertical processes until unloading. A series of experiments and simulations were performed to validate the formulation in the theory, leading to the development of the computer codes. The whole deformation history and the distribution of stress, strain and thickness during the forming process were obtained by carefully considering the moving boundary condition in the finite-element method. Therefore, this modeling can be used for judging whether a equilateral vertical steel can be shaped successfully. The present work may be expected to improve the understanding of the formation of the equilateral vertical steel.
Abstract: To derive the fractional flow equation oil
displacement will be assumed to take place under the so-called
diffusive flow condition. The constraints are that fluid saturations at
any point in the linear displacement path are uniformly distributed
with respect to thickness; this allows the displacement to be described
mathematically in one dimension. The simultaneous flow of oil and
water can be modeled using thickness averaged relative permeability,
along the centerline of the reservoir. The condition for fluid potential
equilibrium is simply that of hydrostatic equilibrium for which the
saturation distribution can be determined as a function of capillary
pressure and therefore, height. That is the fluids are distributed in
accordance with capillary-gravity equilibrium.
This paper focused on the fraction flow of water versus
cumulative oil recoveries using Buckley Leverett method. Several
field cases have been developed to aid in analysis. Producing watercut
(at surface conditions) will be compared with the cumulative oil
recovery at breakthrough for the flowing fluid.
Abstract: An explicit axisymmetrical FE methodology is
developed here to study the particle temperature arising in WC-Co
particle on an AISI 1045 steel substrate. Parameters of constitutive
Johnson-cook model were used for simulation. The results show that
particle velocity and kinetic energy have important role in
temperature arising of particles.
Abstract: Natural fibres have emerged as the potential reinforcement material for composites and thus gain attraction by many researchers. This is mainly due to their applicable benefits as they offer low density, low cost, renewable, biodegradability and environmentally harmless and also comparable mechanical properties with synthetic fibre composites. The properties of hybrid composites highly depends on several factors, including the interaction of fillers with the polymeric matrix, shape and size (aspect ratio), and orientation of fillers [1]. In this study, natural fibre kenaf composites and kenaf/fibreglass hybrid composites were fabricated by a combination of hand lay-up method and cold-press method. The effect of different fibre types (powder, short and long) on the tensile properties of composites is investigated. The kenaf composites with and without the addition of fibreglass were then characterized by tensile testing and scanning electron microscopy. A significant improvement in tensile strength and modulus were indicated by the introduction of long kenaf/woven fibreglass hybrid composite. However, the opposite trends are observed in kenaf powder composite. Fractographic observation shows that fibre/matrix debonding causes the fibres pull out. This phenomenon results in the fibre and matrix fracture.
Abstract: Image Edge Detection is one of the most important
parts of image processing. In this paper, by fuzzy technique, a new
method is used to improve digital image edge detection. In this
method, a 3x3 mask is employed to process each pixel by means of
vicinity. Each pixel is considered a fuzzy input and by examining
fuzzy rules in its vicinity, the edge pixel is specified and by utilizing
calculation algorithms in image processing, edges are displayed more
clearly. This method shows significant improvement compared to
different edge detection methods (e.g. Sobel, Canny).
Abstract: This work presents a methodology for the selection
and design of propeller oriented to the experimental verification of
theoretical results. The problem of propeller selection and design
usually present itself in the following manner: a certain air volume
and static pressure are required for a certain system. Once the
necessity of fan design on a theoretical basis has been recognized, it
is possible to determinate the dimensions for a fan unit so that it will
perform in accordance with a certain set of specifications. The same
procedures in this work then can be applied in other propeller
selection.
Abstract: A Space Vector based Pulse Width Modulation
control technique for the three-phase PWM converter is proposed in
this paper. The proposed control scheme is based on a synchronous
reference frame model. High performance and efficiency is obtained
with regards to the DC bus voltage and the power factor
considerations of the PWM rectifier thus leading to low losses.
MATLAB/SIMULINK are used as a platform for the simulations and
a SIMULINK model is presented in the paper. The results show that
the proposed model demonstrates better performance and properties
compared to the traditional SPWM method and the method improves
the dynamic performance of the closed loop drastically.
For the Space Vector based Pulse Width Modulation, Sine signal
is the reference waveform and triangle waveform is the carrier
waveform. When the value sine signal is large than triangle signal,
the pulse will start produce to high. And then when the triangular
signals higher than sine signal, the pulse will come to low. SPWM
output will changed by changing the value of the modulation index
and frequency used in this system to produce more pulse width. The
more pulse width produced, the output voltage will have lower
harmonics contents and the resolution increase.
Abstract: One of the main objectives of order reduction is to
design a controller of lower order which can effectively control the
original high order system so that the overall system is of lower
order and easy to understand. In this paper, a simple method is
presented for controller design of a higher order discrete system.
First the original higher order discrete system in reduced to a lower
order model. Then a Proportional Integral Derivative (PID)
controller is designed for lower order model. An error minimization
technique is employed for both order reduction and controller
design. For the error minimization purpose, Differential Evolution
(DE) optimization algorithm has been employed. DE method is
based on the minimization of the Integral Squared Error (ISE)
between the desired response and actual response pertaining to a
unit step input. Finally the designed PID controller is connected to
the original higher order discrete system to get the desired
specification. The validity of the proposed method is illustrated
through a numerical example.
Abstract: The purpose of this study was to investigate the religious behavior of students in high school and universality in Lamerd , a town in the south of Iran, with respect to increase in their level of education and age. The participants were 450 high school and university students in all levels from first year of junior high school
to the senior university students who were chosen through multistage
cluster sampling method and their religious behavior was
studied. Through the revised questionnaire by Nezar Alany from the University of Bahrain (r = 0/797), the religious behavior of the subjects were analyzed. Results showed that students in high school
in religious behavior were superior to the students of university (003/0>p) and there was a decline of religious behavior in junior high school third year students to second students of the same school
(042/0>p). More important is that the decrease in religious behavior was associated with increase in educational levels (017/0>p) and age (043/0>p).
Abstract: MM-Path, an acronym for Method/Message Path, describes the dynamic interactions between methods in object-oriented systems. This paper discusses the classifications of MM-Path, based on the characteristics of object-oriented software. We categorize it according to the generation reasons, the effect scope and the composition of MM-Path. A formalized representation of MM-Path is also proposed, which has considered the influence of state on response method sequences of messages. .Moreover, an automatic MM-Path generation approach based on UML Statechart diagram has been presented, and the difficulties in identifying and generating MM-Path can be solved. . As a result, it provides a solid foundation for further research on test cases generation based on MM-Path.
Abstract: In this paper the principle, basic torque theory and design optimisation of a six-phase reluctance dc machine are considered. A trapezoidal phase current waveform for the machine drive is proposed and evaluated to minimise ripple torque. Low cost normal laminated salient-pole rotors with and without slits and chamfered poles are investigated. The six-phase machine is optimised in multi-dimensions by linking the finite-element analysis method directly with an optimisation algorithm; the objective function is to maximise the torque per copper losses of the machine. The armature reaction effect is investigated in detail and found to be severe. The measured and calculated torque performances of a 35 kW optimum designed six-phase reluctance dc machine drive are presented.
Abstract: This paper presents the use of three-dimensional finite
elements coupled with infinite elements to investigate the ground
vibrations at the surface in terms of the peak particle velocity (PPV)
due to construction of the first bore of the Dublin Port Tunnel. This
situation is analysed using a commercially available general-purpose
finite element package ABAQUS. A series of parametric studies is
carried out to examine the sensitivity of the predicted vibrations to
variations in the various input parameters required by finite element
method, including the stiffness and the damping of ground. The
results of this study show that stiffness has a more significant effect
on the PPV rather than the damping of the ground.
Abstract: This paper describes the design of new method of
propagation delay measurement in micro and nanostructures during
characterization of ASIC standard library cell. Providing more
accuracy timing information about library cell to the design team we
can improve a quality of timing analysis inside of ASIC design flow
process. Also, this information could be very useful for semiconductor
foundry team to make correction in technology process. By
comparison of the propagation delay in the CMOS element and result
of analog SPICE simulation. It was implemented as digital IP core for
semiconductor manufacturing process. Specialized method helps to
observe the propagation time delay in one element of the standard-cell
library with up-to picoseconds accuracy and less. Thus, the special
useful solutions for VLSI schematic to parameters extraction, basic
cell layout verification, design simulation and verification are
announced.
Abstract: The Genetic Algorithm (GA) is one of the most important methods used to solve many combinatorial optimization problems. Therefore, many researchers have tried to improve the GA by using different methods and operations in order to find the optimal solution within reasonable time. This paper proposes an improved GA (IGA), where the new crossover operation, population reformulates operation, multi mutation operation, partial local optimal mutation operation, and rearrangement operation are used to solve the Traveling Salesman Problem. The proposed IGA was then compared with three GAs, which use different crossover operations and mutations. The results of this comparison show that the IGA can achieve better results for the solutions in a faster time.